Search Documents

By J. Chai, Q. Yuan, B. Qiu

"Overburden strata deformation monitoring is one of the key problems in ground control. Using geophysical method through surface drilling to detect strata deformation is commonly used in the industry. In this paper, a geophysical method based on the distributed optical fiber sensing (DOFS) system were conducted in the laboratory, where a DOFS-based strata deformation monitoring experiment was performed with three physical models. The results show that the DOFS method precisely detects the rock mass deformation and strata structure forming with the Brillouin frequency shifts (BFS) representation. The BFS curves are divided into three phases, which reflects the horizontal three zones developed in the overburden. The BFS distribution presents a multiple stages form, the 1st stage corresponds to the caving zone and the 2nd stage corresponds to the fracture zone. Based on the multiple stages form, the evolution of the water flowing through fractured zone have been determined and the controlling effect of key strata over the water flowing fracture has been pointed out. In the end, the comparison validation proves the accuracy and reliability of this method, and it could be a new approach for the ground control research. INTRODUCTION Overburden rock strata above the work face space will propagate from slight deformation, part destruction to violent movement because of the underground coal mining. It is fundamental and an intrinsic requirement of ground control to monitor the mining-induced rock mass deformation.[1] Overburden strata have their significant mechanical behaviors and movement under damage deformation and fracture. Overburden strata deformation affect the mining ground pressure control directly, and performance in the relationship of supporting equipment and the surrounding rock, the mining-induced fracture distribution and the loss of underground water resource, the ground surface structure stability and the ecological environment.[2] From the perspective of the concept of safe and efficient scientific coal mining: the overburden strata deformation is an important part of mining method selection and reasonable supporting solutions decision which can solve the issues like the roof supporting force calculation, overburden fracture distribution and gas drainage, ground subsidence, separation of coal and rock control and top-coal recovery rate and so on. From the perspective of green and ecological mining: the overburden strata deformation is the key basis of studying the mining-induced ground subsidence and mining area ecological damage, and such engineering problem like environmental protection in mining area, ecological restoration in mining subsided land and the water conservation in fragile ecology area of mining could be solved based on it.[3-6] Therefore, the mining-induced overburden strata deformation is the key of ground control and needs to be controlled artificially."

Jan 1, 2017

By M. Stuart

The copper-silver-mercury orebody of Gortdrum Mines (Ireland) Limited is located 3 miles north of the town of Tipperary in the Republic of Ireland. A drilling programme from 1964 to 1966 delineated an ore¬body of 4.19 million tons of copper ore assaying 1.19% Cu and 0.75 ozs per ton Ag, which could be mined from an open pit. Testwork having shown that the ore was amenable to conventional flotation techniques, it was decided to build a concentrator of 500,000 tons ore per year capacity. Stripping of the open pit commenced in 1966 and in the autumn of 1967 the concentrator started up. The first shipments of concentrates were made to the smelter in Europe in late 1967. In the spring of the following year, word was received from the smelter that these early shipments contained between 1% and 2% Hg, and that the smelter could not accept further shipments of this quality.

Jan 1, 1973

By B. R. Arvidson

Sharper separation and improved control of the top size increases the fine particle product yield. As the milling circuit recycle stream is reduced, the overall capacity is increased. In some cases, a doubling of throughput is realized, although 25 to 30% increase is more typical. Alternatively, the energy demand may be reduced, although the best economic improvement results from higher capacity. A comparison with a high-pressure roller mill circuit shows that an optimized ball mill circuit retrofitted with the new air classifier has lower energy consumption. The new air classifier features low energy demand and substantially lower maintenance compared to similar equipment. Design and operation of this recently patented classifier are discussed. Several industrial installations will be described.

Jan 1, 1999

By X. P. Zheng

Barium fluorphlogopites were synthesized in the laboratory in order to investigate the effects of composition and crystal parameters on surface properties and floatability. The negative surface charge of mica is determined by the barium content, the crystal cell volume, the distance between layer structure and the Ba-O bond length. The higher barium content, the larger the cell volume and distance between the layer structure and the longer the Ba-O bond, the more negatively charged the surface is and hence the more easily adsorbed to cationic collectors. When an anionic collector (sodium oleate) is used, barium oleate forms on the mica surface and hence chemical adsorption occurs.

Jan 1, 1993

Power consumption of stirred media mills has been studied by an approach developed from work on stirred reactors. Relationships between torque required to rotate both disc and pin impellers immersed in dense particulate media as a function of speed, impeller and tank dimensions, and other relevant variables are evaluated. Data collected during numerous different experimental conditions are analyzed. The results can be summarized and presented in the form of characteristic plots, general equations and dimensionless group correlations involving power and modified Reynolds numbers. Special attention is directed towards the rheological properties of the media, which is considered as non-Newtonian liquids and hence, the equation of power law liquids is employed. Procedure for estimating parameters of effective viscosity and scale-up guidelines with respect to power consumption are put forward.

Jan 1, 1994

By Hemendra N. Kalia

Several attempts have been made in the past sixty or so years to commerciliaze the vast oil shale deposits of the United States of America. However, the industry has yet to become viable and economic. To date, it has not been possible to produce oil from the oil shales at a competitive price when compared to the oil produced from oilfields by conventional methods. However, the development work has been quite fruitful in furthering the art of thick bed mining and technology of in situ retorting. The in situ method has the potential of recovering oil from thick beds and the resource recovery potential is much greater than that from underground mining and surface retorting. In situ methods require that the shales/ marlstones be fragmented ' in place to induce adequate porosity and permeability to allow in situ' heating of the fragmented shales. This can be accomplished by using explosives. However, it has been found that the existing blasting systems, though very efficient, are somewhat lacking. The explosive become insensitive when shot in multiple vertical decks. They can also become insensitive when spaced horizontally at close proximity to other charges. Also, since the blasting is done in a very limited free face, this limits the delay time that can be allowed between charges. Consequently it is not always possible to predict the performance of the blasting system on a routine basis. Furthermore, since it is not possible to undertake secodary blasting, it is imperative that the blast design function properly. Recent, successful retorting by Occidental Petroleum Company of retorts seven and eight suggests that some of these problems may have been overcome. This paper addresses some aspects of in situ retorting and problems those have impeded the development of a viable oil shale industry in the U.S.A.

Jan 1, 1983

By J. B. Lott

The authors' company has recently undertaken a development programme aimed at exploring the relationships between the variables of greatest importance in the design of mixer-settlers for metallurgical solvent extraction applications. Such applications vary from relatively small scale plants treating copper mine waters, nickel containing effluents, etc., where the total flowrates may be of the order of a few hundreds of gallons per minute, to very large scale plants treating several thousands of gallons per minute of leach liquors containing copper, uranium or other metals. This paper outlines the physical and mechanical factors which must be taken into account when designing mixer-settler systems for large scam. solvent extraction plants. The performance of the equipment will also be dependent upon the chemistry of the system, including the kinetics and thermodynamics of the ion exchange reaction itself, the effect of impurities flocculants, surfactants, temperature, etc., but these will not be dealt with here. Much of the laboratory work has been carried out using copper containing solutions and either LIX 64* or LIX 64N* as the solvent dissolved in various grades of kerosene. For simplicity, all the graphs and tables of results which are presented and discussed here will refer to the LIX-copper system, although the conclusions will in many cases be generally applicable to other systems also. The LIX-copper process is now sufficiently well known to obviate the need for a full description, however, an outline flowsheet of the process is shown in Figure 1. The ultimate objective of a laboratory programme for a particular extraction application is to provide data upon which a mixer-settler system can be designed to handle a given throughput of leach liquor and extract from this liquor the maximum quantity of metal for the minimum cost. In other words, the objective is to determine the design and operating parameters which achieve the optimum balance between capital and operating costs. * Trade-marks for General Mills solvents.

Jan 1, 1971

Zirconium chloride is of great commercial importance as starting materials for production of ZrO2, Zirconium metal and other Zirconium compounds from its main resources (Zircon Sands). The present study concerns with preparation of pure ZrO2 from Zircon by direct chlorination technique. Different parameters affecting the chlorination process are studied viz. carbon, chlorine flow rate temperature and time. The chlorination extent is determined from the loss in weight and chemical analysis of reaction products. The maximum chlorination extent -92% are achieved at 1100°C for 30 min. Zirconium oxide is produced from the collected zirconium tetrachloride either by calcination at 900°C or by hydrolysis in water in presence of RCI with a purity = 99%. Evaluations of the products of the process are investigated microscopically and by X-ray diffraction. The apparent activation energy of the chlorination of Zircon is determined to equal 36 kJ/mole.

Jan 1, 1997

By AJIT SWAIN, SUNATI MOHANTY

The abstract discusses the importance of predicting the dewatering performance of industrial hydrocyclones from laboratory models. It highlights the challenge of scaling up design and operating parameters for efficiency estimation. The paper describes experiments with a 2-inch and 4-inch hydrocyclone using silica sand. It details the development of a model using the Nageswararao hydrocyclone model and a simulator to estimate model parameters. The model is validated with experimental data, and a new model is developed using 4-inch hydrocyclone data. The technique is then extended to predict dimensions for a full-scale dewatering cyclone operating at higher throughput and solid concentration.

Mar 30, 2022

By Dave G. Osborne

With the growing exportation of coal from North America to the Pacific Rim countries and Europe, has come an increasing awareness of the need to determine economically optimized amounts of incombustibles (ash and moisture contents) for the shipped product. Despite the fact that demand bas caused a steady improvement in selling price, particularly for thermal coals, growing production and transportation costs have compelled producers to keep a sharp eye open for ways and means of minimizing the latter since this probably represents the greatest single potential for making savings. Consequently the Coal Industry has become acutely aware of the economic ramifications of eliminating moisture in particular, thereby producing further saving in the cost of transportation of product from the mine to the consumer. There is, however, a lower limit to which dewatering or drying can be taken and this relates to dustiness which is a function of the characteristics of the coal and the methods used for handling and storage during trans-shipment. Overdrying can lead to serious dust losses and difficulties in handling particularly if the coal contains a large proportion of fines. The ways and means for achieving this "happy medium" of optimization in moisture removal are seemingly undergoing gradual modification largely assisted by the following factors. a) Improvement in effectiveness of coal dewatering and drying equipment. b) Improvement in operational availability and utilization of the equipment. c) The development of surfactants, polymer flocculants and other agents which in many cases can be almost tailor made to suit specific applications.

Jan 1, 1982

The accurate estimation of ore reserves along with capital and operating costs are two key components to the successful outcome of any feasibility study. In recent years, there have been many project failures caused by improper estimation of ore reserves. The accurate estimation of ore reserves for any deposit relies heavily on understanding its geology and underlying assumptions unique to the estimation techniques being used. The assumptions unique to commonly used traditional and geostatistical reserve estimation technique will be reviewed. The shortcomings of the estimation techniques and their possible impact on a given project's economic outcome will be discussed. The latest developments in geostatistics in overcoming existing reserve estimation problems will be presented.

Jan 1, 1994

By Mason L. Dicks

For many years The Hanna Mining Company has been investigating the flotation of the non-magnetic iron ores located in the Western Mesabi Range of Minnesota.1 During the 1950's a number of anionic iron procedures were evaluated and in the late 1950's and early 1960's the anionic silica floats and the cationic silica floats were tested with improved results.2 The cationic float became more attractive and effective by the use of the improved ether amines. About 1962 a desliming process by selective flocculation was developed by the U.S. Bureau of Hines at Minneapolis', Minnesota.3, 4, 5 This is a very efficient method of desliming and was first tried with the anionic silica float and then the more practical cationic silica float. In the mid 1960's The Hanna Research Laboratory began studies to optimize the selective flocculation process for our ores. This was followed by studies to optimize the cationic silica float after desliming by selective flocculation. This testwork was done on large, 500 to 1000 tonne bulk samples of oxidized taconite which were later successfully piloted at .68t/h (1500 Lbs. /hr.). A program was then begun to test the oxidized portions of numerous taconite drill holes to outline the ore bodies and develop mining plans. This paper will discuss our optimization results of both the selective flocculation and the cationic silica float as applied to our various ores. In addition the pilot plant studies and drill core testwork will be discussed.

Jan 1, 1978

By Yuting Xue

Classification of rock and coal is one preliminary problem for fully automated or intelligent mining. It assists in automated rib stability analysis and enables the shearer to adjust the drums without human intervention. This paper studies the classification of rock from coal on rib images using machine learning techniques. A database of rock and coal images was created by filtering photographs taken by NIOSH researchers during site visits. Machine learning was conducted on patches, smaller images randomly extracted from each rock or coal image. After training, the classifier was validated with the testing dataset and achieved an accuracy score of 0.9.

Jan 13, 2022

By A. K. Stagg

Toxic substances in On solutions can retard biological leaching of copper sulfide dump ores. On solutions were analyzed for metals, organics, and chloride, and showed inhibitory concentrations of aluminum, manganese, and chloride. Inhibition of bacterial activity by the solid fraction of On solution, with and without the organic constituents, was evaluated. Toxicity to bacterial species was evaluated by monitoring bacterial numbers, pH, Eh, and rates of iron oxidation. The On solution solids were toxic at 50 -60% of their field concentration. Most of the toxicity of the On solution was due to the organic fraction. Different SX reagents show varying degrees of inhibition of T. ferrooxidans. Bacterial inhibitory effects of carriers and lixiviants used in the SX plant should be determined so that entrained SX reagents do not retard biological dump leach systems. The reagents used should be the most cost effective and the least toxic.

Jan 1, 1994

By W. A. Crosby

All mine operators using explosives want to maximize explosive performance while minimizing blasting costs. Use of bulk explosive products such as AN/FO, heavy AN/FO, slurries and emulsions has greatly improved blasting efficiency over the years. Many operators have improved energy output from these products by adding aluminum. A major problem facing them is the fluctuation in aluminum price. The question therefore becomes, when is it economically advantageous to use aluminum in bulk products? This paper answers this question by first reviewing the energy output from the main types of aluminized and non aluminized bulk mixed explosives and then by showing the relationship between the different products on a cost and energy basis. The paper finally presents examples of charts and tables which will aid mine operators to conveniently select the most economically correct bulk explosive, including the level of aluminum addition.

Jan 1, 1991

By D. Malhotra

The number of variables which can effect flotation of molybdenite is very large. This paper discusses the effect of two operating variables, namely, the degree of aeration and agitation, on the grade and recovery of molybdenite. A series of factorially designed flotation tests were carried out in a "Leeds Automatic Laboratory Flotation Cell." The analysis of flotation results indicate that molybdenite can be characterized into fast-floating and slow-floating components. The rates of fast-floating components, which do not create a problem in flotation, could be varied by changing agitation of airflow rates. However, the rate of slow-floating components was stable and was only a function of residence time in the float machine. The degree of aeration has a significant effect on the grade of MoS2 with only a slight effect on the recovery of MoS2. The degree of agitation has a slight effect on the grade, but does not effect the recovery of molybdenite. The implications of the results on the design of flotation cells and control and optimization of the existing circuits is subsequently discussed.

Jan 1, 1977

By Miles L. Silberman

Three major suites of igneous rocks were erupted in the Great Basin in middle and late Cenozoic time. The first, most likely, resulted from sub- duction of a Pacific plate (Farallon plate) beneath the North American plate, resulting in eruption of andesitic rocks in the northern Great Basin between 42 and 43 m.y. ago. Between 34 and 17 m.y. ago, igneous activity migrated to the southwest, largely as eruption of volumincus rhyolite-quartz latite ash-flow sheets, ending about 17 a.y. ago with the onset of crustal extension and north-south-trending Basin and Range (rift) faulting. The second volcanic suite erupted between 17 and 8 m.y. ago in the northern Great Basin; is mostly basaltic or bimodal basalt-rhyolite. The third volcanic suite consists of andesitic and rhyolitic lavas and some basalt erupted between about 22 to 6 m.y. ago in the western Great Basin along the northwest-trending Walker Lane fault zone. Hydrothermal ore deposits are associated with all suites of igneous rocks, but the largest production has come from mines associated with andesitic rocks of the third (western Great Basin) suite. The oldest (34 to 42 m.y.) andesitic rocks (first suite) of the northern Great Basin have produced some large deposits; slightly younger silicic rocks of this suite are mostly barren. Many small ore deposits are associated with the 17- to 8-m.y.-old basalts (second suite) of northern Nevada.

Jan 1, 1976

By Clarence Hardy Long

In January of 1969 the United States Department of Health, Education and Welfare, through the National Air Pollution Control Administration, published a series of Air Quality Criteria (4'S) and Control Techniques (6,7) for air pollutants in compliance with the 1967 Clean Air Act which will affect the operation of all fuel burning equipment in the very near future. The design of equipment for the future which will use fossil fuels will also be affected. The purpose of this paper is to discuss some of the modifications which might be anticipated in the future for fuel burning equipment. One class of the several air pollutants looked at first by the USDHEW was the sulfur oxides. Other pollutants, such as nitrogen oxides, will be studied and controls for these will supposedly be written in due time. The obvious use of low-sulfur fuels, coal, oil and natural gas is suggested by the Control Technique(6). Conversion to other sources of power, such as nuclear energy and hydropower, is also suggested. The statement is made that since possible hydroelectric sources are limited and nuclear plants are not yet available on a large scale, the changeover to these sources of power will not be overnight. The bulletin (6) suggests that one possible solution in some areas may be the use of low sulfur coals for short periods of time during periods of severe air pollution. A curve showing the effect of this was given in the 1969 April issue of the Power magazine, where A. E. Boyer and F. B. Kaylor of Stone and Webster also described a computer program called DOSAGE which might be used to check weather, temperature, humidity, wind direction and velocity, and sound an alarm when that 0.1% of the time per season is here that requires the use of low-sulfur fuel. Inversion is eminent! Once this has passed operation on regular fuel may be resumed. This would mean a separate storage

Jan 1, 1970

By J. A. Delgadillo, C. A. Pérez-Alonso

"Tumbling mills using balls as grinding media are used extensively in the mining and cement industries to produce fine powders; however, it is well known that the process of size reduction is highly energy-intensive. For this reason, much of today’s comminution research is aimed at understanding grinding mechanisms, by estimating power draft and modeling milling circuits using the discrete element method (DEM). DEM predicts individual particle trajectories, the distribution of energy and contact forces at each collision, lifter wear and power draw. This paper presents a prediction of the discharge particle size distribution using three components, mass balance model (sometimes referred to as a population balance model, PBM), impact energy distribution of the mill obtained from the simulation of the charge motion using DEM and breakage characteristics of particles determined from drop-ball tests. DEM simulation of the charge of a tumbling mill was done using the code MinProSim 1.0 to obtain impact spectra at different operative conditions. Then, the population balance model (PBM), based on impact energy distribution, was used to predict the final particle size distribution in a batch mill and compared with experimental data. It is demonstrated that the DEM-PBM approach allows a reliable solution to predict particle size distribution for tumbling mills. Ideally, the model has to predict size distribution for any operational condition and feed characteristic; however, it has been shown that predictions include some degree of error.IntroductionThe discrete element method (DEM) has recently become a powerful numerical tool that can be used to investigate internal mill charge in ball mills. The early work of Cundall and Strack (1979) used DEM to analyze soil as a discrete medium. Later, the method was improved to simulate the operation of tumbling mills and optimize the design in order to increase the efficiency of energy utilization. Also, it is of great interest to relate ore breakage based on impact energy spectra obtained by DEM simulations and the breakage distribution function used in the PBM to predict particle size distribution in tumbling mills.King and Borgeous (1993) broke single particles in an ultra fast impact load cell to compute the phenomenological parameters in a microscopically more detailed population balance model. Kapur et al. (1997) simulated the size spectra of progeny particles produced by impact grinding as a function of the impact energy. Narayanan (1987), Narayanan and Whiten (1988) and Lira and Kavetsky (1990) estimated the energy-dependent breakage distribution function for scaleup and modeling of industrial ball mills."

Jan 1, 2015

By Panshi Xie, Yingyi Zhang, JIANJIE DUAN, Shenghu Luo

A multi-layer gangue roof of a steeply dipping coal seam with a large mining height face area was analyzed using physical simulation, numerical simulation, theoretical analysis, and field measurement methods to evaluate the roof deformation and the mechanisms associated with the instability of the hard gangue and soft coal interlayer. The results indicated that the first weighting step of the multi-gangue roof was larger than that of a non-gangue roof, but periodic weighting steps were similar. The overburden collapse height was lower in the multi-gangue roof than in the non-gangue roof due to the buffering and supporting function of the collapsed gangue. Moreover, the failure of the coal interlayer was the key factor in the collapse of the multi-layer gangue. A mechanical model was established for the hard gangue and soft coal interlayer based on a revised Prandtl squeezing theory. The limited load of the interlayer and maximum resistance of the shield support was thusmodeled. The maximum resistance of the support increased with the dip angle of the seam and burial depth. It also increased with the interlayer thickness at thicknesses below 2.75 m. It reached a peak when the interlayer thickness was between 2.75 and 3 m and exhibited a decreasing trend when the thickness was greater than 3 m. The results were confirmed using physical simulation and a field test. Certain measures were proposed to control the stability of the gangue roof, including zoning control of the mining height and resistance and advancing the support while maintaining roof contact, thus ensuring the integrity of the support and surrounding rock system.

Jun 30, 2020