Search Documents

By John H. Paugh

Hydraulic slurrying and pumpability characteristics of phosphate matrix (ore) have not been quantitatively defined. An elemental triangular diagram analysis of rock/sediment texture is used to classify the nature of the ore; then related to empirical field data of hydraulic pressureand production yardage ratios. This experiment is applied as a geotechnical tool to provide empirical data of ore slurry and pumpability characteristics as key considerations in the design of slurry pipeline systems. A real texture variability maps are developed on a section of land to assist mine engineering planning.

Jan 1, 1981

By John Dodd

Advances in the technology of abrasion resistant irons and steels, which could help in combating abrasion and wear in mining operations, are reviewed. Nodular irons alloyed with nickel or copper and molybdenum, with acicular, bainitic or bainitic-martensicic microstructures are described. These alloy irons combine excellent castability and relatively easy machinabilitv with good resistance to wear. Recent progress in the development of high chromium molybdenum alloy irons is outlined, by which high temperature heat treatment of massive castings can be eliminated, alloy costs can be reduced and cracking problems avoided. Data is also given on the erosion-corrosion resistance of these irons. Trends in the development of improved cast steels are outlined. Factors influencing the toughness and abrasion resistance of manganese steels are considered. The 6% Mn 1% Mo manganese steels are shown to have a useful combination of toughness and abrasion resistance. Composite castings are seen as a means of com- bating abrasion in applications involving severe impact. A brief appraisal is given of recently developed martensitic wrought steels with improved weldability.

Jan 1, 1981

By Q. Xu

The adsorption behavior of gold in ammoniacal solutions on to activated carbon has been studied. The gold loading capacity of the activated carbon used in the system and the recovery efficiency by the adsorption were examined. The parameters affecting the adsorption of gold on to activated carbon included temperature, agitation speed, concentration of 'cation and anion as well as that of ammonia. It was found that the maximum gold loading on activated carbon used was about 10 kg of gold per ton of carbon. The recovery of gold by the adsorption from ammoniacal solutions was dependent upon the initial gold concentration in the solution. A recovery of 98% of gold was obtained on to the activated carbon under experimental conditions after 120 hour adsorption. It was also found that the initial adsorption rate was relatively fast compared to the whole period of the adsorption. The apparent activation energy for the adsorption was measured to be 15.8 kJ/mol. It was believed that the kinetics of gold adsorption on activated carbon was controlled by pore diffusion.

Jan 1, 1995

By D. L. Kiser

Conventional and advanced coal preparation technologies were investigated through both a literature search and through direct contact with investigators and developers. In addition to a brief description of each process, performance characteristics including feedstock type, ash and sulfur reduction, thermal energy recovery and cost are provided in a tabular form. Seven of the most commonly utilized conventional coal preparation processes, including those respectively accepting coarse, intermediate and fine coal feed, were reviewed. It was found that certain properly implemented and well maintained conventional processes were capable of better than 75 percent ash removal while recovering 90 percent or more of the inherent thermal energy. Almost 50 advanced coal preparation processes were investigated based on biological, chemical and physical principles. Physical processes investigated included cycloning, homogeneous heavy media, electrostatic, high gradient magnetic, flotation and selective coalescence. Using pulverized coal as a feedstock, some of these processes are respectively reported to be capable of removing better than 95 percent ash. 95 percent pyritic sulfur, and 50 percent organic sulfur while incurring energy losses of less than 5 percent.

Jan 1, 1986

By B. J. Arnold, F. F. Aplan

Prior laboratory work has demonstrated that much of the fine ash forming minerals entering a flotation froth are there as a result of water carryover- from the bulk contents of the flotation cell (Arnold and Aplan, 1986a). Using a bank of four 8.5 m3 (300 cu ft) Wemco flotation cells cleaning a well-liberated Lower Kittanning seam coal, test results show that the sulfur and ash content of the froth is directly related to the water content of the froth (or inversely related to the percent solids in the froth). Reagent changes that result in a watery froth produce a higher ash content in the froth. A direct comparison of laboratory and plant results show that the standard laboratory flotation test produces a product higher in sulfur and ash than that produced in the plant. Caution should be exercised when extrapolating laboratory test results to the plant situation. A method of estimating coal flotation product quality in the plant based on laboratory tests is given.

Jan 1, 1991

By D. S. Davies

Further development of the Nitric-Sulfuric Leach (NSL) process has led to an improved design of the leach and nitric acid recovery steps. NO produced in the leach step is reacted with oxygen, regenerating N02, which is sparged directly into the leach reactor. Leaching is simplified to two steps and the nitric acid plant is replaced with an oxidation recycle gas sys-tem. Laboratory work substantiated the concept and led to selection of operating conditions. The lab work also pointed to improved process control compared to use of nitric acid as the sole oxidant. Recovery of copper from purified pregnant liquor is modified to use air agitation electrowinning improving cathode quality and lowering tankhouse costs. Economic evaluation shows reduction of capital requirements from $2400/AT to $2000/AT in 1978 dollars for 50,000 TPY of copper production.

Jan 1, 1978

By Brij M. Moudgil

Separation of oil shale from waste material or into high grade and low grade fractions can have a major influence on the economics of the surface (ex-situ) retorting process. Different components of shale rock vary significantly in physical and surface chemical properties such as specific gravity, color, water wettability etc. Various techniques which utilize the difference in one or more of the above propartis have been proposed to preconcentrate the oil shale before retorting. A discussion of the techniques proposed such as gravity separation, sorting and froth flotation is presented.

Jan 1, 1982

By P. Lan

Gold is often associated with arsenopyrite in many refractory gold ores. The selective recovery of arsenopyrite by flotation is therefore necessary in order to maximize the recovery of gold. However, the complexity of arsenopyrite flotation often makes it difficult to obtain a high recovery from real lean gold ore. This paper presents the results of arsenopyrite flotation by ultrasonic pretreatment in micro flotation experiments and bench scale flotation tests. The tests showed that pure arsenopyrite exhibited low natural floatability due to the oxidation on the mineral surface under ambient conditions. Using ultrasonic pretreatment, the oxidation film was ruptured and the floatability was enhanced greatly. The presence of Fe (III) was found to inhibit the flotation of arsenopyrite and this depression was also removed by the ultrasonic pretreatment. This result explained why the arsenopyrite in real ore is often difficult to float and how ultrasonic pretreatment can effectively improve the arsenopyrite flotation in real gold ores. Guanidine (GMM) was found to be a superior collector for arsenopyrite in acidic medium and xanthate in alkaline medium.

Jan 1, 1998

By Francis Martino

There are numerous techniques and predictive models used by geologists and mining engineers to define coal reserves and plan mines. The traditional reserve estimation methods commonly used include the isopach, triangular, polygonal, inverse-distance weighting, weighted-moving-average, and trend-surface methods. Geostatistically-based estimation techniques are now being examined by many geologists and mine planners as a superior alternative to these traditional methods. With today's coal mine development costs often exceeding $100 million, and power generation $1 billion, it is logical that a technique that can indicate the degree of confidence associated with a reserve estimate (fuel supply), and thus also the degree of risk, is highly desirable to the coal producer, the financiers, and those desiring to commit to coal utilization under short or long-term supply arrangements.

Jan 1, 1983

By K. V. Godfrey

With the increasing need to exercise better control over mill circuits has come a requirement to develop rapid, accurate means of measuring circuit parameters. One of the most important parameters is the assay of the material in the circuit (or about to be introduced to the circuit). To date, most on-stream analysis has been performed using X-ray fluorescence equipment. Neutron activation offers an alternative method in certain circumstances, and one which has several interesting advantages. Recognizing the need for a simple, safe neutron activation unit suitable for on-stream analysis in the mineral industries, Atomic Energy of Canada Limited has designed, built and tested the SHERLOCK system. One prototype (SHERLOCK I) is located in Ottawa and is now used primarily in research. A second prototype (SHERLOCK III) is located in Vancouver at the laboratories of B.C. Research. This unit is being used for some development research and for evaluating the unit in specific applications. Most of the work completed to date has been aimed at proving the technique and in developing some of the parameters needed to design systems for a milling plant. Funding for the work has been through research grants and through sponsor¬ship by interested companies.

Jan 1, 1971

By İsmail İnce

The existence of water is one of the most effective factors in deterioration of natural building stones. In the process of deterioration, capillary water absorption is the most significant procedure of water penetration into the building stones. Pyroclastic rocks have been widely utilized as building stone especially in historical buildings and monuments since ancient times in the Central Anatolia in Turkey. Nowadays, this type of rocks is used in the restoration of historical buildings as well as in the construction of modern buildings. Pyroclastic rocks are highly susceptible to deterioration process. Capillary rise has a significant influence on water penetration into building stones. Therefore, it is quite important to identify the factors affecting the values of capillarity, capillary rising speed, and capillary rise that define capillary water absorption in these rocks. To this end, pyroclastic rock samples in different textures were compiled from the Cappadocia region, in Central Anatolia. First, petrographic, mineralogical, geochemical, physical, and pore diameter distribution properties of the samples were determined in the laboratory. Then, capillarity values with capillary rise and capillary rise speeds dependent on time were established. Based on the data obtained, correlation coefficients between matrix percentage and capillary water absorption rate and capillary rise values of pyroclastic rocks were calculated and found to be as 0.850 and 0.891, respectively. Thus, the article proposes a new empirical equation to practically calculate the capillary rise value depending on the matrix percentage (MP) and median pore diameter (MPD) values.

Nov 30, 2020

By Alan Bauer

In recent years there has been increasing interest in employing the technique of explosive casting in strip mines. Explosive casting, applied to dragline mining, describes the procedure whereby the overburden is horizontally displaced by blasting causing a portion of the material to be thrown into the previously mined cut. Therefore, it is not necessary to subsequently excavate this waste with the stripping equipment. In addition, allowing the overburden unrestricted movement during the blast most often results in improved fragmentation and enhanced machine productivity. The method is receiving attention because the capital and maintenance costs of stripping equipment has risen rapidly in relation to explosives costs. Improved productivity is necessary to maintain unit costs at an acceptable level.

Jan 1, 1983

By Erik S. Bernard

"INTRODUCTION Reinforced Concrete (RC) members such as beams and columns are usually required to include stirrups to maintain post-crack shear capacity, and some may include stirrups that act as confining steel to maintain structural integrity during a seismic event (eg. NZS3101, ACI 318). To achieve seismic resistance, the spacing between stirrups is usually required to be much closer than is ordinarily prescribed for non-seismically resistant structures. Each stirrup must also fully enclose the longitudinal reinforcement with long end-hooks to ensure that the contained concrete is sufficiently restrained during reverse-cycle loading and the reinforcing bars are confined to prevent buckling. The close spacing between stirrups can lead to congestion of reinforcement within members, and can also be expensive to construct due to the labor-intensive nature of steel fixing. A possible alternative to closely-spaced stirrups is the use of fibers to provide restraint and confinement during a seismic event, although this is not yet recognized in codes. Previous experimental research (Jiuru et al, 1992; Filiatrault et al, 1995; Bayasi and Gebman, 2002; Billington and Yoon, 2004) has demonstrated that steel fibers are relatively effective in this application, but suffer the problem that their stiffness can make them difficult to consolidate within an already tight reinforcement cage, especially if they are relatively long (>40 mm). Moreover, steel fiber reinforced concrete (SFRC) is subject to embrittlement with the passage of time, leading to a steady loss of ductility beyond crack widths of 1-2 mm (Banthia and Trottier, 1994; Bernard and Hanke, 2002; Bernard, 2014; Bjontegaard et al, 2014; Bernard, 2015). Since cracks during seismic events are generally much larger than this, embrittlement may present a challenge to the long-term efficacy of SFRC during seismic events. An alternative to steel fibers for enhancement of seismic resistance is the use of macro-synthetic fibers. This type of fiber usually offers the advantage of being flexible so that consolidation is easier between reinforcing bars. They also offer superior durability compared to steel fibers and can reduce flexural crack widths (Bernard, 2016). Several recent small-scale investigations (Ma et al, 2012; Carnovale, 2012; Osorio et al, 2014) have indicated that macro-synthetic fibers can produce meaningful improvements in seismic resistance if used in combination with conventional steel reinforcing bars. The present investigation has extended research in this field by examining whether embossed macro-synthetic fibers can be used to increase the spacing between stirrups while maintaining seismic resistance."

Jan 1, 2016

By Knut H. Hubert

The GRATE-KILN System plant at Svappavaara, Sweden, was constructed for LKAB by Allis-Chalmers under a turnkey contract and commissioned in 1969. The plant was designed to produce iron ore pellets from magnetite concentrate at 6100 mtpd using imported fuel oil. It represented the state of the art for plants of its type at the time. Fuel rated capacity was attained within one week of start-up. Product quality, power usage, fuel consumption and machine wear were within warranty limits during sustained production thereafter. As operator skills improved and gas handling system reserve capability was utilized, the plant frequently produced acceptable product at up to 115% of design capacity. During the period 1969 to 1976, market demands increased for high-quality pellets while energy costs rose steadily. At the same time, important advances in the design of GRATE-KILN Systems were being made in other plants constructed by Allis-Chalmers.

Jan 1, 1980

By Sahendra Ram, Priyadarshi Onam, Abhishek Kumar Singh

A numerical simulation study is carried out for assessment of stability of coal pillars having dirt bands by varying its size and depths. Physico-mechanical properties of dirt bands including thickness and its position in pillar system are varied in the simulation study. Results of the simulation study are correlated with the available empirical approaches of pillar strength are validated with field observations. It is observed that the presence of weak dirt bands significantly influences the strength of pillar. An attempt is made to develop correction factor for the available empirical approaches, which are developed without considering the weak dirt bands in pillar system. The findings of the study will be helpful for suitable design of different size of coal pillars at different depths and stages of depillaring operations.

Feb 1, 2025

The criteria used to design, operate and control flotation columns are significantly different from those used for conventional flotation machines. Therefore, a computer-aided design (CAD) package for column flotation has been developed. The simulator has been set up using guidelines developed at Virginia Tech and information published in literature during the past few years. The simulator is useful for determining the proper design and appropriate operating conditions for a column cell to fit a specific set of conditions. In addition, the simulator can be used for training in column operation and for trouble-shooting operational problems. Simulation results have been found to be in good agreement with experimental data obtained using laboratory columns.

Jan 1, 1990

By M. T. Ityokumbul

The liquid phase mixing in Western Research Centre (WRC) pilot plant flotation column with diameter of 0.76 m has been characterized using a salt tracer. The process variables studied were gas and liquid flow rates. The response of the column to a tracer pulse input was monitored at three axial and two radial locations. For all the experimental conditions investigated in the present study, radial and axial concentration gradients were not observed. It is thus concluded that the 2 tph flotation column is behaving as a well mixed tank. This finding is consistent with the observed poor recoveries of coarse fractions in the column flotation circuit. Based on the findings of this report, it is recommended that several schemes of reducing the backmixing be implemented and evaluated for their effectiveness in improving the column recoveries.

Jan 1, 1994

By D. Antonov

The physical and mechanical properties of coal play a important role in the planing and design of coal mines. However, due to the complexity conditions in situ and the influence of unknown factors, it is hard for people to evaluate the physical and mechanical properties of coal directly. In this research, uniaxial compressive stress was used to change the attribute of coal samples, and the ultrasonic measure technique was used to evaluate the physical and mechanical properties of coal. The results of laboratory test showed that there was a strong relation between uniaxial stress and velocity of ultrasonic wave. Sensitivity analysis with numerical simulation was used to define the relation between the physical-mechanical parameters of coal and ultrasonoc wave. With the dynamic analysis module of FLAC, three elastic and plastic models were built to model the coal samples. The modeling parameters were changed pro rata, and the correlation of coal and ultrasonic wave properties were summarized and presented. The result from this research will be base for further analysis of caving behavior of coal.

Jan 1, 2010

By Bradley S. Van Gosen, Anjana K. Shah, George M. Bedinger, Donald I. Bleiwas, Karl J. Ellefsen

"Ancient and modern coastal deposits of heavy mineral sands (HMS) are the principal source of several heavy industrial minerals, with mining and processing operations on every continent except Antarctica. For example, HMS deposits are the main source of titanium feedstock for the titanium dioxide (TiO2) pigments industry, obtained from the minerals ilmenite (Fe2+TiO3), rutile (TiO2) and leucoxene (an alteration product of ilmenite). HMS deposits are also the principal source of zircon (ZrSiO4), from which zirconium dioxide (ZrO2) is obtained for uses mostly in refractory products. Sometimes monazite [(Ce,La,Nd,Th) PO4] is recovered as a byproduct mineral, sought for its rare earth elements, and thorium (Ault and others, 2016; Sengupta and Van Gosen, 2016; Van Gosen and Tulsidas, 2016).HMS are sediments containing dense (heavy) minerals that accumulate with sand, silt and clay in coastal environments, locally forming economic concentrations of the heavy minerals (Fig. 1). Economic (mined) HMS deposits include Holocene sediments on modern coasts, such as examples in India and Brazil, as well as coastal deposits formed by transgressions and regressions of the seas during intervals in the Quaternary, Tertiary and Cretaceous, such as in Australia and the southeastern United States. Economic deposits typically contain heavy-mineral concentrations of at least two percent. Individual heavy minerals are commonly defined as minerals with a specific gravity greater than approximately 2.9 g/cm3. These minerals are generally resistant to chemical weathering and physical degradation and thus survive well in fluvial and coastal environments. Heavy minerals in coastal HMS deposits may include, in order of general abundance, ilmenite, leucoxene, rutile, magnetite, zircon, staurolite, kyanite, sillimanite, tourmaline, garnet, epidote, hornblende, spinel, iron oxides, sulfides, anatase, monazite, cassiterite and xenotime. Of these, ilmenite, leucoxene, rutile and zircon are the primary economic minerals. Garnet, monazite, cassiterite and xenotime are occasionally recovered as byproducts. The heavy minerals as a suite typically make up no more than 15 weight percent of a deposit and usually much less. Quartz and clay minerals form the bulk of the sediment. The geology of HMS deposits and examples of significant districts are summarized in Van Gosen and others (2014) and Hou and Keeling (2016)."

Oct 1, 2016

By P. B. Queneau

An operating problem encountered at the Moa Bay operation in Cuba, where nickeliferous laterite ore is processed by sulfuric acid pressure leaching, is the formation of alunite and hematite deposits on the autoclave walls. The AMPX Extractive Research & Development, Inc., metallurgical laboratory (Golden, Colorado) has made substantial improvements in the Moa Bay process in the areas of metal recovery, energy consumption, and feed versatility. One of the advantages of AMAX's process is its ability to treat substantial portions of nickel- and magnesium-rich serpentine while maintaining acid utilization efficiency. The process minimizes scale formation by combining staged acid addition with vigorous agitation and 270°C operation, but does not eliminate scaling. This paper describes how advantage can be taken of MgSO4?XH20 precipitation both to inhibit alunite scaling and to disperse hematite scale within the MgSO4?XH20 matrix. Cooling the autoclave from its 270°C operating temperature down to 180°C takes advantage of the reverse solubility of magnesium sulfate. The magnesium dissolves, liberating entrained hematite, thus providing a means for control of autoclave scale with minimum process disruption.

Jan 1, 1984