Search Documents

By Bo-Hyun Kim, Mark K. Larson

"Researchers at the National Institute for Occupational Safety and Health (NIOSH) have advocated the use of instrumentation in underground mine ground control studies to aid in understanding failure mechanisms and to calibrate numerical models. The purpose of these efforts is to reduce accidents and fatalities in underground mines resulting from inadequate design of mining layout or supports. A recent examination of some results of stress change measurement raised some questions about the validity of elastic solutions in ground, such as coal. Particularly under deep cover as is prevalent in the western United States, the coal around a borehole would likely have yielded so that post-yield behavior would govern the response of the instrument.A numerical experiment was conducted by NIOSH researchers using the FLAC software (Itasca Consulting Group, 2016) to investigate the response of the borehole pressure cell (BPC) and the biaxial stressmeter to varying degrees of plastic behavior. The pre-encapsulated BPC cell pressure exhibits increasing departure from the elastic case with decreasing post-peak-strength slope of the stress-strain curve. On the other hand, because the BSM usually provides much more confinement to the surrounding rock than does the BPC, the measurements obtained from the BSM do not depart significantly from the changes in secondary principal stresses and directions as calculated by the elastic solution.INTRODUCTIONSeveral years ago, Larson et al. (2000) described several instruments that NIOSH had used in underground field studies and how to monitor them with dataloggers. This information is still relevant because of the need to understand how excavation affects the stability of mines and thus, the safety of mining personnel. One class of instruments described in that paper includes those instruments that measure change in rock stress. Although several such instruments might be used to measure stress change, the focus of this paper is on two instruments with which NIOSH has had more recent experience—the borehole pressure cell (BPC) (Geokon, 2018a; RST Instruments, 2018) and the biaxial stressmeter (BSM) (Geokon, 2018b). Other instruments, such as the CSIRO hollow inclusion stress cell (HICell) (Earth Sciences, 2019; Worotnicki and Walton, 1976) may be included in future studies.Early studies in the development of the BPC were those of Panek and Stock (USBM, 1964), Sellers (1970), Lu (1984), and Babcock (1986). Babcock’s work is particularly useful, but his setting and testing range was far below what we experienced in the NIOSH study, and it was Babcock’s data reduction scheme from his laboratory experiments that was used to calculate stress change in the NIOSH study (NIOSH, 2019a)."

Jan 1, 2019

By V. F. Hollister

Copper and gold were discovered in the Copper Canyon area of the Battle Mountain district of Lander County, Nevada, in August of 1866. By 1876 a gravity plant was con¬centrating oxidized Copper Canyon copper-gold ores. The history of mining in the district to 1967 has been summarized by John E. Frost (in press) as a case history of the discovery of the Battle Mountain porphyry copper deposits. His summary is not repeated here; rather, the present case history covers exploration since 1967, primarily for gold ores. Subsequent to the construction by Duval of facilities to mine the porphyry copper deposits in 1967, Duval established a geologic staff at the mine to continue district exploration. The staff was guided by David W. Blake, who acted as chief geologist for Duval's exploration in this part of Nevada. Blake's activities led to the publication of numerous technical articles, including his contribution to the US Geological Survey Professional Paper 798-B. A part of that volume is attached as a reprint (pages 23 through 66) as an explanation of the geological setting of mineralization in the district. The work by Blake and his staff recognized metal zonation in the skarn environment at Copper Canyon, and their studies were incorporated in the development of the Tomboy-Minnie gold deposits that are peripheral to the porphyry. Exploration continued beyond the immediate vicinity of the porphyry and the Fortitude ore zones were discovered. These skarn deposits are described in the attached article by Wotruba, Benson, and Schmidt, published in the July 1986, MINING ENGINEERING. The continued exploration successes at Battle Mountain reflect on the well organized and effective exploration team developed at the mine. The team has provided successive discoveries in a district known mostly for ore bodies that are exhausted in a few years' time.

Jan 1, 1990

By Nasri Munfah

Long Island Rail Road’s (LIRR) service to New York City is limited to Penn Station on the West Side of Manhattan, which is operating at its practical capacity for the commuter railroad. This situation imposes serious considerations for future growth and limits the destination of many Long Island commuters. The East Side Access Project will provide a connection of the LIRR to the landmark Grand Central Terminal (GCT)on the East Side of Manhattan. The construction of the connection will require significant tunneling and underground work utilizing a variety of construction techniques. In Queens, the connection will require five soft ground tunnels using pressurized face tunnel boring machine. In Manhattan, the connection will require a series of rock tunnels and caverns connecting to two deep large station caverns under GCT to accommodate eight tracks with four platforms in a stacked configuration. The caverns housing train rooms are connected to the lower level of GCT where a large concourse will be provided. With a budget of $4.3 Billion, The East Side Access Project is the largest transportation project ever undertaken in New York City. This paper provides an overview of the project, discusses its environmental and the engineering challenges, and provides an insight into the design development to date.

Jan 1, 2001

By J. B. Hiskey, V. M. Sanchez

Electrochemical oxidation of arsenopyrite (FeAsS) has been investigated as an attempt to gain a better understanding of its dissolution chemistry. Rest potential measurements, cyclic voltammetry and constant potential experiments were conducted in the pH range from 8 to 12 in the absence and the in the presence of cyanide. A two-step reaction sequence is suggested by the electrochemical measurements. The initial step is described by: [FeAsS+6H20=Fe(OH)3+H2AsO3- +S°+7H++6e] The second step involves the oxidation of the arsenite and sulfur according to the following reactions: [H2As03-+H20=HAsO24-+3H++2e and S° +4 H2O=SO4-+3H++6e] Stoichiometric determinations confirm that 14 electrons are involved in the overall reaction.

Jan 1, 1992

By Ava Walker

The first form of a surety bond was an honest handshake between two or more parties agreeing to a decision, and their personal guarantee of following through to completion. This has all changed. In 1895, the United States Treasury Department disclosed that $35 million worth of personal surety guarantees on file had become worthless. A law was then passed requiring all surety bonds, in favor of the United States, must be corporate surety bonds. Today, a surety bond is one of the nation's leading fi¬nancial instruments used to guarantee the completion of an obligation. One hundred-fifty years before cor¬porate surety bonds, outcrops near Richmond, VA, were being mined. These surface mines became under¬ground mines. Today, both are still being used to obtain a leading energy source, coal. Since that time, more than 5956 km2 (1.47 million acres) of coal mined lands have been reclaimed in the US (Coal News, August, 1987). More than 25,000 state and Federal mining permits cover¬ing 14,164 km2 (3.5 million acres) have been issued during the last 10 years. Coal production has exceeded 7.2 Gt (8 billion st). More than 5665 km2 (1.4 million acres) of mined land has been reclaimed by active coal mining opera¬tions and 267 km2 (66,000 acres) of abandoned mined lands have been re¬claimed by others. Reclamation bonds were freely writ¬ten in the 1970s. So why are they almost extinct today? Contract bond losses have been severe in the past several years, sureties reporting losses exceed¬ing 110%. But the same proof is not provided on coal reclamation bonds. A surety bond is generally required when one party has an agreement with another party, and that party wants a guarantee from a third party that a job will be completed according to the terms and conditions of a written contract. In the case of a reclamation bond, the surety company (surety) is the financial party. It extends the credit and a guarantee to the obligee (the State, Commonwealth, or Office of Surface Mining) that the principal (the coal operator/company) will complete the terms and conditions of the contract (the rules and regulations governing mining and reclamation). The Surety Association of America defines a surety bond as an agreement providing for monetary compensation should there be a failure to perform specified acts within a stated period. Webster's Dictionary defines surety in the following ways: "l: the state of being sure; 2a: a pledge or other formal engagement given for the fulfillment of an undertaking and; 3b: one who has become legally liable for the debt, de¬fault, or failure in duty of another." Banks never make accommodation loans. Either the loan is good or no loan is made. Surety companies feel the same way about surety bonds. In fact, the average person does not realize the dangers of becoming surety for another. How does a surety determine if a company is worthy of receiving surety credit? How is a coal account under¬written today for an obligation that may not be released for many years? When a surety company executes a reclama¬tion bond, it financially puts its name behind the coal company and its guaran¬tee that should the coal miner default on the obligation, the surety will fulfill the contract. How is the surety to determine if a coal company may still be in business five, 10, 20, or 40 years from today?

Jan 1, 1989

By Elvin R. Beach, Jaroslaw Drelich

Pull-off forces were measured for 8-9 pm diameter polystyrene (PSI particles on smooth spin- coated polystyrene films and hexadecanethiol (HDT) self-assemble monolayer surfaces using atomic force microscopy (AFM). Three parameters were controlled during experimentation: (i) the maximum applied load pressing the particle onto the substrate was varied from 50 to 4,000 nN, (ii) loading/unloading rate for the particle to attach and separate from the substrate varied from 0.01 to 9.3 Hz, and (iii) contact time for particle to reside on the substrate surface before retracting the particle to separate it from the surface changed from I µsecond to 200 seconds. the pull-off forces increased with increasing applied loading, increasing loading/unloading rate, and increasing contact time for the PS particle on PS film and on HDT monolayer. The PS particles experience elastic and plastic deformations duringpull-08 force measurements. Plastic deformation is primarily associated with flattening of surface irregularities. The results obtained in this research suggest that the particle-substrate contact areas of the magnitude comparable to those predicted by the JKR contact mechanical model can be reached in the AFM experiments by using high applied loads and long particle-substrate contact times. This result re-opens the prospect of' using AFM for studying surface energies of deformable micro-particles, even if the micro-particles have small irregularities on the surface.

Jan 1, 2003

By Michael J. Cruickshank

MICHAEL J. CRUICKSHANK SENIOR AUTHOR Marine mining is a very broad field. It encompasses every facet of terrestrial mining but with the unique addition of a superimposed liquid overburden, which is itself mineralized. It is the unique aspects of marine mining that are discussed in this section. In keeping with the times, a systems approach is taken in the presentation of the material. The environment is first described, and this is followed in logical sequence by the common requirements for working there, then the mineral exploration phase, the exploitation and, finally, the operational restraints imposed by man and nature. Free use is made of tables and figures from original and published works and extensive listings of reference material round out each section. The title "Marine Mining" was chosen in preference to ocean or underwater mining because it is broad enough to include oceans, beaches and inland seas. The selection of terms sometimes may seem odd but they have not been chosen arbitrarily. All things are reduced, where possible, to basics and defined. Applying systems terminology, the word "platforms" is used in the functional sense and includes not only airborne, waterborne and fixed platforms, but man himself in his capacity as a working diver. If there is confusion it is often because of familiarity with a word in a context personal to the reader. For example, what does extraction mean to you-or mining or exploitation? Cost data have been interspersed throughout the section whenever they could be obtained. The use of these data should be tempered with understanding because no two situations are alike and improvements in marine technology are constantly being made. The names of individual authors are listed with each subsection. Where no name is given, the responsibility has been that of the senior author. Acknowledgment is sincerely made to the U.S. Bureau of Mines, and latterly the National Oceanic and Atmospheric Administration, for encouraging and supporting the preparation of the work ; to the secretarial staff at the Marine Minerals Technology Center and to Donald Eisman for editing. To the many other contributors who may not be listed by name, grateful acknowledgment is also due. It is hoped that the chapter will be useful to the practicing mining engineer who suddenly is assigned to marine work or to the experienced marine engineer who is equally suddenly assigned to mining work. It is not possible to put "everything-you -need-to¬-know" into one section, but. the very full bibliographies at the end of the text should adequately fill in for those who wish to know more. 20.1-THE MARINE ENVIRONMENT Marine mining is set apart as a separate discipline by the marine environment. The following subsections describe the environment from the point of view of the physicist, the chemist and the geologist. The interrelationship of these disciplines with the economic mineral potential of the oceans and seas is apparent from the description of the marine mineral resources. The marine environment is an extremely complex natural phenomenon with which the marine mining engineer must learn to live. It can be the source of his wealth or his frustrations and sometimes both. It can never be ignored.

Jan 1, 1973

By K. L. Gabby

Selective removal of mercury from cyanide leaching solutions while retaining silver has been a long-standing problem, due to the chemical similarity of mercury and silver. In order to be practical, a mercury removal process needs to be both highly selective and use inexpensive materials. This paper reports the use of zinc sulfide (ZnS) as a precipitant for mercury. The mercury cyanide complex (Hg(CN)4 2-) undergoes a replacement reaction with the zinc sulfide, forming insoluble HgS, while the silver cyanide complex (Ag(CN)2 -) remains in solution. Under appropriate conditions, the separation of mercury from silver is nearly quantitative, with close to 100% removal of mercury, while nearly none of the silver is precipitated.

By H. C. Harrell

The Tennessee Valley Authority began employing geophysical well logging for foundation investigations in October 1973. Since that time more than 3,000 holes have been evaluated for engineering purposes. The Tennessee Valley Authority has not actively used geo-physical well logging for exploration of construction materials, but we feel that much of the information derived from geophysical logs for foundation exploration is applicable to the construction materials industry. This paper will then discuss geophysical logging as applied to foundation engineering and, by implication, the feasibility of use in construction materials exploration. The use of geophysical logging and percussion drilling instead of coring has greatly expanded TVA's data acquisition capabilities and has also resulted in substantial savings in time and money. Economical boreholes are obtained through the use of large percussion track drills (Figure 1). This equipment is capable of drilling through the overburden, setting steel casing on the top of rock, and drilling the rock beneath the casing. Holes as deep as 400 feet (121.9 m) have been drilled by this method.

Jan 1, 1977

By Meili Zhu, Qingpu Shi

High temperature, methane, dust and other disasters are getting more serious with mining depth getting deeper and the development of mechanization in underground mines. An application of a descensional ventilation to a coalface is one of the effective measures to solve the above problemes. The descensional ventilation is an venttilation that an airflow in a coalface wouuld downflow along an inclination of a coalface and the direction of the airflow is the same as coalflow. Since 1960's, the descensional ventilation has been applied to 171 coalfaces in 46 coal mines of 23 coal mine administrations in China, such as Pingdingshan , Zhongliangshan, Pubai, Huangshi coal mine administrations. Among the 171 coalfaces, there were 104 coalfaces taking 60.8% in gently inclined seam. The coalfaces in inclined seam and steep seam were individually taking 18.7 % and 20.5 %. There were 77 coalfaces taking 45 % of the total in low gassy coal mines and coal and methane outburst mine were individually taking 17% and 38%. There were 141 coalfaces taking 82.5% of the total in potential danger of dust explosion. There were 125 coalfaces taking 73.1% of the total in potential danger of spontaneous combustion. Therefore, the descensional ventilation can be used in coalfaces under different conditions in China. The practice at home and abroad shown that the application of the descensional ventilation to coalfaces has obvious results in dust control, temperature control, preventing methane accumulation at top corner angle and control of spontaneous combustion in goaf. To more safely and reliably apply the descensional ventilation to coalface and to provide a way for the development of mine ventilation technology in China, the paper will have discussions on the following problems: METHANE EMISSION AND DISTRIBUTION AT COALFACE WITH DESCENSIONAL VENTILATION Methane emission in a coalface with a descensional ventilation is an argued issue for many years. Base on the coal practice, special similar model tests and researches in China, the followings are our main comments. The Descensional Ventilation can Reduce the Methane, Accumulation at the Top Corner Angle. The measurements in six coalfaces with the downward airflow in Qinhemen Mine, Fuxin Coal Mine Administrations shown that the methane concentration at the top corner angle is often up to l% when the coalface has the upward, airflow. The max. methane concentration at the top corner angle is about 0.49 to 0.7% when the coalface has the descensional ventilation. Therefore, with the descensional ventilation, it basically solved the overlimited gas concentration at the top corner angle which is a potential danger to coal production. Because the direction of upfloating gas is opposite to the direction, of the descensional airflow, the descensional ventilation; could increase a turbulent flow mixing capacity of the methan gas and air, and reduce a possibility of methane; accumulation. Due to an air leakage in goat when the coalface with the descensional ventilation lower than an air leakage in goat when the coalface with the, ascensional ventilation, a less methane quantity will release from goat at the descensional ventialtion. It should be pointed out that due to a higher air leakage at ascensional ventilation and the direction of the air; leakage same to the direction of the natural upfloating methane in goaf, those will cause a large methane; accumulation at the top of the goaf and easy bring about, methane accumulation and overlimited methane concentration at the top corner angle with an ventilation vortexflow at the top corner angle. On the other hand, because the direction of the upfloation force function is upward, the descentional ventilation could minimize as possibility of methane accumulation at top corner angle in coal with the descensional ventiltion.

Jan 1, 1991

By R. M. Barker

The historic Getchell property, near Golconda, NV, is being mined from the Getchell Main Under- ground workings, a footwall extension of the Getchell open-pit deposits along the Getchell fault. Drift-and-fill techniques are used to extract the ore through a ramp access. The adjacent Turquoise Ridge deposit is under development by two vertical shafts. These two mines will continue to provide feed to the Getchell's 2.9 ktld (3,200 stpd) mill/autoclave circuit. This will take Getchell Gold from its current production rate of 6.2 t/a (200,000 oz/year) to more than 12.4 t/a (400,000 oz/year) by 1999.

Jan 1, 1997

By Richard Newcomb, Michael Rieber, William A. Vogely

INTRODUCTION The solid fossil and nuclear fuels, but especially uranium, are given prominent, indeed leading, roles by energy experts in most long range estimates of world energy futures. Optimistic forecasts are inspired partly by the disproportionately large solid fuels resource base compared to present rates of consumption or to oil and gas resources, and partly by the vision of inexpensive high technology applications. Such a view overlooks the fact that while resource- use disparities and new technologies give allure to the promise of the solid fuels, they do not guarantee cheap solutions to the basic problems of solid fuel uses: viz., their relatively difficult conditions for efficient ignition and control, including the management of environmentally acceptable residuals disposal. Contrary to the varied versions of this optimistic hypothesis, this paper shows that a great many persistent economic and technical problems interfere with such a simple inference. These act as constraints which qualify or dispute much of the national energy policy based on existing modeling of solid fuel requirements and optimistic engineering evaluations. The assumptions and techniques of such exercises are sometimes at fault. As often as not, however, the distortions created in open market fuel com- petition due to misdirected national energy policies themselves are to blame for misdirected efforts. A number of interesting implications result. Among them are the distinct possibility that the low technology applications will dominate, so that more direct coal and less synfuel or nuclear use will occur; that, accordingly, exhaustion rates for uranium will be low, that the most extensive growth of solid fuel through 2000 will be in conventional pulverized coal cumbustors, and that the traded share of the world coal bum will be much larger than predicted. These trends will place much more pressure on oil and gas prices than forecast by most experts. On the way to these findings the paper demonstrates that solid fuel resource adequacy in situ, balanced against the projections of demands as capacity requirements, mean little as conventionally measured by years to exhaustion or potential supply schedules. Indeed, all stock concepts of demand requirements or of fuel re- sources must be tied to the paths of the unit costs and the deliverable prices of all substitute fuels and systems over time. This requires a dynamic analysis of supply and demand, integrated with geological and engineering constraints, to provide insights into the multiple modes of market and product substitution. Market forces rather than technical promise will determine the allocation of the solid fuels. Moreover, the equilibrium paths of individual fuel prices and market shares are not easily simulated by general or network models, and decision makers will continue to rely on the partial, local comparison of alternatives in their choices of fuel systems at any time. 'The economics of the solid fuels differs from that of other energy sources in important ways relating to their form in use, conversion efficiency, (dis)economies and externalities. Petroleum and gas are in a more convenient form for

Jan 1, 1985

By J. D. McKay

The Bureau of Mines devised a column flotation technique using either fine or coarse bubbles and compared it with conventional flotation on a Montana chromite ore. On deslimed ore, fine-bubble column flotation produced a 44.7-pct-Cr203-grade rougher concentrate with 87-pct recovery, compared with 43.8- and 43.5-pct-Cr203-grade rougher concentrates with 85- and 77-pct recovery for coarse-bubble column flotation and conventional flotation, respectively. On undeslimed ore, coarse-and fine-bubble column flotation produced rougher concentrates containing approximately 41.5-pct-Cr203 with 95-pct recovery, exceeding conventional flotation which produced 35.6-pct-Cr203-grade concentrates with 87-pct recovery.

Jan 1, 1985

By Jeffrey A. Yonkey, Timothy J. Lutz, Jacob L. Carr, Christopher C. Jobes

"Since 1984, there have been 39 fatalities involving striking and pinning of the operator and other workers by the continuous mining machine (CMM). In January 2015, the U.S. Mine Safety and Health Administration (MSHA) finalized a regulation to require proximity detection systems on all continuous mining machines except full-face machines (MSHA, 2015). Proximity detection systems are designed to stop machine motion to protect miners from striking/pinning hazards. Several MSHAapproved proximity detection systems are commercially available.NIOSH researchers have been involved in the development and testing of proximity detection technology since creating the HASARD system (Schiffbauer, 2002) and have recently conducted research intended to develop more advanced proximity detection technology for CMMs (DuCarme et al. 2013; Jobes et al. 2012; Carr, DuCarme et al. 2013 and Carr, Li et al. 2013). In addition, NIOSH has also conducted research investigating how the signals of a proximity detection system propagate (Li, Carr et al. 2013 and Li, Jobes et al. 2012) and have developed a novel method for determining the location of a personal wearable device (PWD) relative to the magnetic field generators (Carr et al. 2010 and Jobes, et al. 2012).To evaluate the performance of proximity detection systems implemented in industry, NIOSH researchers conducted tests in 2013 on three systems installed on CMMs at three underground mines in Illinois and West Virginia. The results of these tests indicated that, while generally consistent performance was observed, there were opportunities for improving performance. These results were presented at the 2014 SME Annual Meeting (Carr, Lutz, et al. 2014). Since that time, second-generation systems have become available to the industry and are becoming more commonly used.Beginning in early 2014, NIOSH researchers conducted underground testing of these secondgeneration proximity detection systems installed on CMMs. Five tests were conducted on four installations of second-generation proximity detection systems, with one installation being tested twice. The tests were conducted at mines located in Illinois, Virginia and Kentucky with seam heights ranging from 137 cm (54 in.) to 213 cm (84 in.). These tests were conducted using the same test protocol used during first-generation testing, which is summarized in the following section."

Jan 1, 2014

By Raphael G. Kazmann

The predicted warming of the earth's surface, presently the subject of much debate, controversy and legislation, is based on what is termed "the greenhouse effect." This is the result of the property of certain atmospheric gases. These gases allow the passage of radiant energy to the earth's surface and reflect back, to the earth, the infrared radiation given out by the heated surface. Physicists have computed that if there were no greenhouse effect the average temperature of the earth, now about 15° C (60T), would be close to -18° C (OT). Just what gases have produced this salubrious effect? Water vapor is the most important. Then come carbon dioxide, methane and a number of minor constituents of the atmosphere, both natural and man-made. Climate change, its cause and its impact on human activities have been the subject of scientific and historical study for more than a century. Recently, some scientists have concluded that if the man-made increase in the carbon dioxide and other greenhouse gases continues, by the late 21st century the earth's global average temperature will rise between 2° to 8° F. This temperature rise would cause the water in the oceans to expand and the massive polar glaciers to melt. In 1980, it was predicted that the sea level would rise 7.6 m (25 ft) by the late 21st century. By 1985, the predicted rise was 1 m (3 ft); and by 1989, it was 0.3 m (1 ft) (Jastrow, Nierenberg and Seitz, 1990). Agricultural scientists have pointed out that an increase in atmospheric carbon dioxide would enhance biological growth including the production of foodstuffs.

Jan 1, 1992

By John Newby, Ulf Gwildis, Ken Massé, Guillaume Roux

How to connect an effluent conveyance tunnel to riser shaft and diffuser arms of an outfall system is dictated by the ground conditions, which ideally include rock or soil strata of low permeability. Where such favorable conditions are beyond reach, both the complexity of designing and the risk of constructing this crucial system connection increase disproportionally. This paper describes the considerations that went into the approach of connecting a 5-m-diameter TBM drive with the in-river riser shaft of the Annacis Island WWTP New Outfall System in the highly permeable Fraser River sands at hydrostatic pressures exceeding 3 bar.

Jun 23, 2024

By M. Popescu

In the southern part ?f the Occidental Carpathians an iron ore body embedded in crystalline schist was exploited. The presence of minerals such as magnetite, pyrite, pyro-chorine, allanite, monazite and xenotime, which also include within their structure substituted thorium isomorphic, was pointed out. The iron ore was processed by crushing, grinding and magnetic separation in order to obtain magnetite concentrates. The environment was affected by pollution generated by the mining activities. In 1995 due to the economic reasons, it was decided to cease mining exploitation and remediate the area. The paper presents the ecological impact caused by mining activities on a number of environmental targets and the population. The pollution sources, namely sterile dumps and mine waters are characterized (from the physical, chemical and radiometric point of view); the pollution pathways and theirs effects on potential targets, namely soil, vegetation, hydrographic network and population are identified as well. The degree of pollution due to all sources was assessed and maps of pollution sources distribution were generated. The supplementary effective doses for the population were assessed using rigorous scenarios and considering all exposure pathways. The rehabilitation plan includes solutions for dumps geometrization, covering and revegetation as well as mine waters management.

Jan 1, 2005

By Carl (Original by) Hrovatic

Land is a precious resource and should be treated as such by all members of our society. The soil covering this earth is only a very thin outer layer, varying in thickness from a few inches to a few feet and covering the rocks and minerals lying beneath the surface. The wise use of this valuable commodity is the responsibility of everyone. Many everyday activities disturb e earth's surface. Examples are highway construction, housing and commercial developments, agriculture, and various types of mining. This chapter discusses the relationships of the environment to land as it applies to surface operations in the coal industry. Mining by surface methods disturbs, for a brief period of time, thousands of acres of land annually. In addition, refuse piles, slurry ponds, abandoned mine structures, unprotected mine openings, and unsightly cleaning plants can also adversely affect land unless properly handled.

Jan 1, 1981

By Brian Fulcher, Matthew Bartlett, Jarrett E. Carlson

This paper discusses the challenges to complete the construction of two large underground Metro stations and connecting tunnels in the Tren Urbano system. The completion work includes the installation of specialized mechanical and electrical systems, extensive architectural finishing as well as coordination with systemwide power and controls installed by others. A unique feature of this project was the simultaneous design and construction of the structural/civil/architectural/mechanical/electrical works by KKZ separately from the power and control systems under the management of the Owner, its consultants and other contractors. Completion of this project comes after almost six years of continuous design and construction in a dense urban environment. The project was confronted by many challenges that could only be met with the combined efforts of the Joint Venture team in close cooperation with the Owner and its System wide Contractor. This paper will also address many of the major design and construction changes implemented to suit the Owner’s requirements.

Jan 1, 2003

By D. Chakravarty, G. Samanta, B. Samanta

The present study highlights the planning and design aspects of a well-known openpit copper deposit in India. The mine has been operational since 1982 and presently reaches a depth of 168 m below the surface. The present planning effort has been given due consideration in view of the recent upsurge of copper prices in the global market. The prime focus of the study has been directed towards examining the possible extent of final pit beyond the current pit outline and generating an extraction sequence of future mining operations. To this end, an orebody model of the deposit has been developed and the optimized pit has been derived using L-G 3D algorithm. A sensitivity analysis has also been performed to scrutinize the possible effects of the changing economic scenarios on the ultimate pit configuration. It has been observed that with the current production rate, mine life can be extended another 40 years. With a five-year production plan, these materials can be extracted in eight push-back schemes. The extraction sequence of these push-backs has been outlined in this paper.

Jan 1, 2011