Search Documents

By Steven W. Hunt

"A paper called “Global Experience with Soft Ground and Weak Rock Tunneling under Very High Groundwater Heads” was presented at the North American Tunneling 2006 conference (Holzhäuser et.al 2006). It summarized global experience with earth pressure balance (EPB) and slurry shield tunneling on nine projects that encountered groundwater heads ranging from 6 to 11 bar. Since then, additional projects have been completed with groundwater heads ranging from 7 to 15 bar. Of these, the high pressure tunneling experience on the Lake Mead Intake No. 3 project in Nevada and on the Eurasia Tunnel (Istanbul Strait Crossing) had the greatest lengths of tunneling at face pressure over 7 bar. Experience with sustained pressurized face tunneling at groundwater heads over 7 bar and risk management observations are the focus of this paper. INTRODUCTION High groundwater head, particularly at 7 bar or more, is a major challenge when tunnelling in high permeability ground and on drives long enough to require cutter changes. It has a strong impact on design and operation of Tunnel Boring Machines (TBMs) in order to protect the main bearing from contamination, prevent excessive groundwater inflow, ensure face stability and enable access to the cutterhead and excavation chamber for maintenance. During the past 20 years, TBM manufacturers and suppliers have made tremendous improvements that allow tunneling at groundwater pressures to 17 bar or more. The most significant risk with high pressure tunneling is generally that of excavation chamber access and potentially the cutterhead for cutter changes, cutterhead repairs and TBM maintenance. Hyperbaric interventions are possible and safety variances have been approved for saturation dive interventions at pressures as high as 17 bar (Lake Mead Intake No. 3). While high pressure hyperbaric intervention equipment is available and safety approvals can be obtained at many locations, few contractors consider the cost and risk of hyperbaric interventions over 7 bar to be acceptable as the primary means of excavation chamber access. Experience with high pressure tunneling prior to 2006 was summarized in a paper entitled “Global Experience with Soft Ground and Weak Rock Tunneling under Very High Groundwater Heads” (Holzhäuser et.al 2006). That paper provided information on 9 projects: South Bay Ocean Outfall, San Diego; Channel Tunnel (French Side), France; Storebaelt Tunnel, Denmark; 4th Elbe Tunnel, Germany; Wesertunnel, Germany; Westerschelde Tunnel, Netherlands; St. Petersburg Red Line, Russia; Nara Prefecture Water Conveyance Tunnel, Japan; and Tokyo Wan Aqua Line Tunnel, Japan – see Table 1."

Jan 1, 2016

By John Reilly

Traditional methods of project procurement of have remained virtually unchanged in the U.S. infrastructure construction industry for more than 50 years. The traditional method, Design-Bid-Build (DBB), uses a two-step process that separates planning and design from construction. Design is generally done by the public agency and their consultants and the subsequent construction contract is procured from the private sector, almost always by a “low-bid” approach. This method has worked well for many projects, delivering quality work for the lowest bid price. This is particularly true for those projects where the work, and the public agency’s management procedures, are well understood by the contracting community and there is relatively low uncertainty in the work or conditions, particularly geotechnical conditions for underground construction. However, concerns exist with the DBB process. It is time consuming because all planning and design work must be completed prior to beginning any construction work and it is of concern for complex or large projects, plus those with significant risk, where the separation of design and construction, in conjunction with pressures resulting from the low-bid environment, often result in substantial cost and schedule increases. Frequently, these increases occur in a non-productive, inefficient, adversarial work environment leading to claims, disputes and costly litigation (Quick 2002).

Jan 1, 2007

Mine Terex articulated dump trucks are working on a large restoration project of an abandoned open cast coal site in Blacklaw, central Scotland. The project is part of the construction of a 42-turbine wind farm complex. During the scheduled 18-month duration of the project, three 28-t(31-st) Generation 7 TA30 dump trucks and the six 36.5-t (40-st) TA40articulated trucks are estimated to move about 1Mm3 (1.3 million cu yd)of material. The trucks are working12-hour shifts, 5.5days a week.

Jan 1, 2005

By Adolph V. Mitterer

International Minerals and Chemical Corporation operates one of six potash mines in the Carlsbad potash basin. More than 90 percent of America's potash is produced at Carlsbad and IMC accounts for about one-fifth of that amount, Since the Company began operations in 1941 it has mined nearly 50 million tons of ore. Of the two types of ore mined at Carlsbad the principal tonnage is sylvinite in which sylvite-potassium chloride-is the ore mineral. It is produced by IMC as well as by all other mines in the area, In addition to sylvinite IMC is the exclusive producer of langbeinite ore--potassium-magnesium sulfate. From its two ores, International produces a spectrum of 8 high-quality agricultural and industrial chemical products.

Jan 1, 1959

By K. A. Natarajan, K. Karthiga Devi

"A biodegradable flocculant was produced during growth of Bacillus megaterium. The major component of the bioflocculant was found to be a polysaccharide composed of some proteins. Fourier transform infrared (FTIR) spectra analysis revealed the presence of carboxyl and hydroxyl groups in the bioflocculant, and thermal characterization by differential scanning calorimetry (DSC) showed the transition and crystalline melting point at 90-105°C. The effects of bioflocculant dosage and pH on the flocculation of mineral suspensions were evaluated. The bioflocculant exhibited good flocculating capability on mineral suspensions and achieved flocculating efficiencies of 90 percent for kaolinite and 85 percent for hematite suspensions at a dosage of only 5 mL/L. The maximum arsenite removal was found to be 90 percent at a bioflocculant dosage of 2 g/L, which is better than traditional chemical flocculants. This study demonstrates that microbial bioflocculants have potential for application in environmental cleanup, such as in the flocculation of mineral fines and in the remediation of solutions that contain toxic heavy metals.IntroductionBioflocculants are biopolymers produced by microorganisms during their growths. The predominant components of a bioflocculant are extracellular polymeric substances such as glycoprotein, protein, cellulose and nucleic acid (Salehizadeh and Shojaosadati, 2001). Bioflocculants have gained much wider attention due to their biodegradability and safety. In recent years, the study of bioflocculants has attracted wide attention. Bioflocculants can be nontoxic, harmless and eco-friendly. Normally, they exhibit different functional properties, serving as stabilizer, dispersant or thickener. Among these properties, flocculation is of major interest. For example, Phormidium sp. strain J-1, isolated from a drainage channel, exhibited excellent flocculation activity for bentonite particles in liquid suspension (Fattom and Shilo, 1984). A protein bioflocculant produced by Rhodococcus erythropolis could efficiently flocculate suspended solids while losing their flocculating activity by enzymatic digestion (Kurane et al., 1994, Takeda et al., 1991). Klebsiella sp. strain S11 screened from activated sludge was unable to flocculate without the addition of calcium chloride (Dermlim et al., 1999)."

Jan 1, 2015

By Raymond L. Zahradnik

Marco Polo reported that the Chinese used "black rocks" for fuel, and recent studies indicate that the Chinese may have used coal in small amounts for two or three millennia previously. The use of coal as a major source of energy however, did not begin until about the twelfth century, when the inhabitants of the northeast coast of England discovered that certain black rocks found along the seashore--and thereafter known as "sea soles" would burn. Since this initial discovery, coal has been mined continuously, first in England and shortly thereafter in present Belgium, France, and Western Germany, and finally in all coal-bearing areas of the world, in ever increasing amounts. The production of coal in the United States began about 1820, when 14 tons were reportedly mined. Since that time the production of coal increased steadily until about 1907, after which the rate has fluctuated between the extremes of about 400 and 700 million tons per year. Bituminous coal and lignite production was 590 million tons in 1974. Value of production was $8. 9 billion. Anthracite production was b.3 million tons with a value of $157.5 million.

Jan 1, 1975

By Peter F. Mataich

The phosphate mining industry is a highly competitive one, one in which survival depends on the plant's ability to produce at costs equal to, or below, the competition. The solution toward getting costs down is usually one of scaling up the plants to get the most tons through at the lowest possible cost. Control of these plants has been an art. Few of them are well instrumented because until a few years ago reliable instrumentation was non-existent. International Minerals and Chemical Corporation was a pioneer in applying computer techniques to ore reserves analysis and mine planning and the success in these areas led to the question of whether we could not extend the advantages of computer processing into the plant itself. There was a great deal of doubt on the operator's end that this could be done successfully because of the lack of instrumentation and the fact that plant control was largely an art that was learned only after many years of experience. However, in 1965 the instrumentation picture began to look up and the new generation of process computers just coming on the market were considerably lower in cost than the previous ones. A preliminary study of the installation costs and the probable benefits that could be realized from computer control convinced us that a process control computer should be seriously considered for a new phosphate mining plant which was being designed.

Jan 1, 1969

By B. Boutilier, R. Mendoza

"First Majestic Silver Corp. (FMS) is a silver mining company founded in 2002 that operates exclusively in Mexico. It has six producing silver mines, one of which is the La Encantada silver mine (La Encantada) located in the state Coahuila. La Encantada is located near the southern United States border and 708 km (440 miles) north of the city Torreon.La Encantada is located in the Sierra Madre Oriental and is a high-temperature carbonate replacement deposit. Mineralization in La Encantada occurs in many different forms such as veins, chimneys, breccia pipes and reefs (mantos). Mineralization is mainly oxides of iron, zinc, lead and manganese, with high concentrations of sulfides at depth relating to two main intrusive events: the Milagros Intrusive and the La Prieta Skarn.Mining began in La Encantada during the 1950s with small vertical shafts, drifts and raises. It focuses on the high-grade silver zones using traditional hoists and extraction methods, before branching into two main separate mining camps: El Plomo and Penoles camp. Penoles, the previous owner, focused mainly on large ore bodies using post pillar cut-and-fill mining method to extract the higher-grade material. Due to the type of ground, irregularity of pillars, and rock conditions, large amounts of high-grade pillars had to be left in situ to ensure the stability of the excavations. The mined-out areas would then be filled with lower-grade material to assist in the stability of the secondary level. These room-and-pillar development entries were 2.5 m x 2.5 m (8.2 ft x 8.2 ft) and spaced every 10 m (32 ft), leaving a vertical pillar of 7.5 m (25 ft). First Majestic acquired La Encantada in 2006. After the acquisition of the mine, the company began the conversion of the surveying reference system from a local grid (Maria Isabel Shaft as 0,0) to the Nav27 coordinate system, and subsequently converted to the WGS84 coordinate system in 2015. Due to the extensive history of the mine, different areas were surveyed with different systems, causing significant challenges when designing the principal extraction levels, pillar heights and ramp locations. To overcome this difficulty, the entire mine was resurveyed and the old workings transposed to the new coordinate system, except for some inaccessible areas due to poor ground conditions or ground collapses. To further ensure pillar height and the safety of the mine workers, probe holes were drilled during the development process."

Sep 1, 2019

By Robert W. Bartlett

Heap biooxidation of sulfidic refractory gold ore requires large amounts of oxygen, as shown in Figure 1. Bacteria, Thiobaci/lus ferrooxidans, are donnant at oxygen concentrations below about 3% in air (1 ppm in aqueous solution) because ofmonod kinet­ics. Hence, the maximum possible utilization is only about 75%, and it may be much less than that due to poor air sweep effi­ciency. At the maximum oxygen utilization, an ore containing two percent pyrite requires nearly 100 cubic meters of air per tonne (4,000 cubic feet per ton). The stoichiometric air require­ment to oxidize arsenopyrite is similar to that of pyrite. While the leaching solution percolating through the heap introduces some dissolved oxygen, the amount is insignificant because of the low solubility of oxygen in water, 7 to 8 ppm at atmospheric saturation. There are only three ways to provide oxygen to the heap: either air flow by natural convection, diffusion of oxygen from the surface (through stagnant air in the air-filled void space in the heap), or forced air ventilation of the heap. Each of these processes will be reviewed.

Jan 1, 1996

By M. Vesely

Abrasive grinding, leading to ultrafine product and "critical size" material build-up inside the mill, is proposed as the cause of high power consumption and low capacity in many fully autogenous grinding processes. Addition of steel balls (hence, semiautogenous grinding) or pebble removal and separate crushing have been used, with different efficiencies, to overcome the problem. Information and data for the conceptual analysis, basic design and operation of a pebble crusher at the Los Bronces semiautogenous grinding plant is presented along with data showing a production increase of 1000 mtpd and significant operating costs savings.

Jan 1, 1985

By M. Rieber

Building on earlier work, an analysis relevant to international (Australasian) minerals trade is developed which accounts for both the impetus of globalization and national reaction or protection. At the firm level, integrated multinationals are contrasted with trade service providers. At the industry level tariff and, particularly, such barriers as quotas, standards, labor and environmental issues are explored. Specific areas examined include: location of both inventories and processing, sources of finance and currency risk, shipping availability and terms as related to processing level, residuals management or environmental controls, and “fair” labor standards. Intraregional rather than global trade is currently most likely.

Jan 1, 2002

By G. Le Bel

The paper proposes three methods to determine optimum lifetime of a mining project1. The conclusion is that the three methods arrive at the same optimum production rate (by coincidence). It is also stated that: "The stochastic and option pricing models, in addition to providing a more realistic optimum mine life than the traditional NPV (net present value) calculation, showed that the example project has the potential for substantially higher return. By explicitly considering a project's potential risks, the stochastic or option pricing techniques can more accurately describe its probable investment performance." This discussion is intended to demonstrate that: • It is no coincidence that the three methods arrive at the same optimum production rate. • The stochastic and option pricing models do not provide a more realistic optimum mine life than the traditional NPV calculation. • The potential for a substantially higher return is misrepresented. First, a review of investment decision theory in mining is needed. Net present value is the preferred performance measure because of the flexibility offered when comparing various alternatives. However, it presents the following disadvantages: • The discount rate selection is not straightforward. • The NPV obtained represents a deterministic characterization of the variables included in the cash flow calculations, i.e. a single-point estimate.

Jan 1, 1993

By M. D. Johnson

Mina Santa Rosa, in west central Panama, is the first large-scale gold mine in Panama and will soon be the largest single-mine gold producer in central America (Fig. 1). At full production, the mine will process 1.8 Mt/a (2 million stpy) of ore and produce more than 1.8 t/a (60,000 oz/year) of gold and 9.3 t/a(300,000 oz/year) of silver. Mina Santa Rosa is a subsidiary of Greenstone Resources of Toronto, Ontario. Freeport-McMoRan geologists first visited the area in 1985. Their rock chip sampling adjacent to old shafts and adits confirmed widespread gold and trace element geochemistry anomalies. Surface mineralization appeared to be localized in and adjacent to narrow veinlets. However, they recognized astructural setting similar to the Nevada Tertiary volcanic-hosted epithermal gold systems.

Jan 1, 1996

By Hans von Michaelis

The current exploration boom in Central and South America shows no sign of abating and, if anything, is growing. This is despite an inevitable cooling in the recent frenzied buying of resource stocks on the Canadian exchanges which have funded much of the Latin American exploration. Several factors appear to be driving the boom. Firstly, the resource potentials in this vast under-explored regions are nothing short of phenomenal. Secondly, after decades of stifling nationalization and restrictions that stood in the way of foreign investment, especially in mining, emerging nations the world over now suddenly find themselves competing with each other to be the most attractive.

Jan 1, 1995

By J. M. Mutmansky, Y. J. Wang

The usual method employed to determine the direction of flow in a connecting airway in advance is to conduct a survey between the two existing nodes being connected by means of the new airway. It is then assumed that airflow will take place from the node with higher pressure to the node with lower pressure. The purpose of this paper is to examine this direction-of-flow problem -- using properties of the system characteristic curve for a two-terminal network -- and specify some conditions that ensure that flow will take from the higher-pressure node to the lower-pressure node. It is concluded that the only requirement is that all characteristic curves of fans in the network should be strictly decreasing. Five numerical examples illustrate some important properties of the direction-of-flow problem.

Jan 1, 1999

By Lloyd M. English

During the past 30 years, the research arena has changed significantly in all fields, mining included. The relative representation of the topics of research, how the research is performed and who has performed the research have all changed. Although there are a lot of subjective ideas and anecdotal "analyses" concerning these changes, there has been no actual study of these trends to verify the facts. This study was divided into six five-¬year periods for the purposes of comparison. Some of the trends analyzed are co-authorship, research areas, research sponsors and cooperative efforts. In today's research arena, 30 years is a long time. Technology has advanced more rapidly than in any time previously and that pace continues to increase. There are more researchers, more tools for research and an increasing number of companies, agencies and institutions engaged in research. The pace of change and its impact is often discussed and debated at professional meetings and in institutions that engage in research. These conversations will often influence the research decisions of the participants in directions to take or subjects to pursue.

Jan 1, 1995

Recent U.S. mine disasters identified a need for improved training of miners in escape from mine fires and explosions. Researchers at the National Institute for Occupational Safety and Health?s (NIOSH) Spokane Research Laboratory (SRL) have designed fire-escape training software for use in a mine-safety training course. The software allows four trainees to work together in a virtual world via a computer network. Trainees responded favorably and showed a marked improvement in locating the proper evacuation routes on subsequent trials. In collaboration with the Pittsburgh Research Laboratory (PRL), a more elaborate fire evacuation scenario is being developed. Further study is needed to confirm that virtual training will translate to improved safety outcomes in the real world. Keywords: virtual reality (VR), safety, training, mining, mine fire evacuation

Jan 1, 2009

By C. Wen

In Huoqiu region of Anhui Province, Fe2O3 occurs mainly in the form of specularite. Besides quartz, the gangue minerals include iron-bearing silicates such as chlorite and sericite which account for about 10% of the total gangue. The separation effect of conventional collectors is poor in the flotation of the minerals, that is, the average grade of iron concentrates is only 60-62%. Using the developed amphoteric collector can successfully realize not only the separation of specularite from various gangue minerals with results of iron concentrate grade above 65% and iron recovery of above 80% but also low temperature flotation at 15°C.

Jan 1, 2012

By Richard E. Thill

Backfilling of mine voids is used to prevent or control the effects of subsidence on surface structures. The pumped-slurry, blind-backfilling process has been particularly successful for stabilizing ground over abandoned and inaccessible underground coal mines. Using this newer technology, vast quantities of backfill material can be distributed over wide areas in underground openings from a small number of injection boreholes. The rapid and successful development of this backfilling method, however, has outstripped technology for monitoring and controlling backfill placement. Surface or borehole remote sensing methods are needed to determine where fill material is being distributed underground and how effectively the material is packed in the voids. In search for improvements in backfill monitoring and control technology, potential remote geophysical sensing, process monitoring, and tracer methods were evaluated to select candidate systems for monitoring backfill placement under the constraints imposed by the injection process and the surface and subsurface conditions. ' A multiple objective ranking matrix, based on theoretical considerations as well as pragmatic experience with systems working in related or similar conditions, was used to narrow down potential methods to several most-favored candidates. Two of the candidates were field tested under actual operating conditions at a backfilling site in the Wilkes-Barre-Scranton region of northeastern Pennsylvania. Although process and acoustic emission monitoring indicated promise for improving existing backfill monitoring technology, more extensive testing under different conditions at various sites is required to establish the validity and utility of these methods. Results indicate that no single method is adequate in itself for backfill monitoring, and that a successful system will require the Integration of several methodologies.

Jan 1, 1982

The first of this three part series examines he history and some of the properties and characteristics of explosives. Use of explosives is discussed for underground and surface coal operations—the largest consumers in the mining industry. Part two of the series will deal with explosives use in surface and underground hardrock operations. Part three will discuss explosives transportation, storage, handling, and destruction.

Jan 7, 1981