Search Documents

By Henk L. C. Meuzelaar

Most of us are aware of the relationship between the golden-yellow resin spots on Upper Cretaceous Wasatch Plateau coals and fossil tree resins (?amber?). Nevertheless, confusion remains about the exact chemical composition and structure of commercial coal resin preparations as well as their observed heterogeneity. In order to arrive at a more detailed chemical description we need to distinguish between micropetrographic, organic geochemical and process technological definitions of coal resins, which may include substantial quantities of constituents unrelated to fossil tree resins. New information on composition and origin obtained by Curie-point pyrolysis/evaporation in combination with isobutane chemical ionization mass spectrometry, as presented in this paper, points to the presence of four more or less distinct resin components: (1) a sesquiterpenoid polymer; (2) sesqui-and triterpenoid monomers and dimers; (3) a suite of triterpenoid alcohols, ketones and acids; and (4) a series of increasingly aromatized hydrocarbons with naphthalene and picene type skeletons. Moreover, a strong similarity is found between the composition of recent Dammar resin and fossil Wasatch Plateau coal resins. Some of the technological implications of these findings and the consequent need for a more precise chemical definition and nomenclature are discussed.

Jan 1, 1990

By J. M. Wempen

As development in underground coal mines progresses away from the critical components of the ventilation system, including the main fans and ventilation shafts, resistance is markedly increased. This results in higher pressure and flow requirements from the main fan(s) to maintain adequate face ventilation, which often requires that the primary ventilation system is upgraded with additional shafts and surface fans. The use of booster fans underground is a potentially practical alternative. This study presents simulations of the use of booster fans in two underground ventilation scenarios, one longwall and one room and pillar. The booster fan effects on the power requirements of the ventilation systems are evaluated.

Jan 1, 2011

By John L. Schroder

The design of an underground mining operation requires the integration of transportation, ventilation, ground control, and mining methods to form a system which provides the highest possible degree of safety for mine personnel; the lowest cost per ton of product; the most suitable quality of final product, considering its intended use; the maximum percent recovery of the reserve, consistent with cost and subsidence rights; and the minimum disturbance to the environment. The selection of mining method is generally the controlling factor in overall mine design. Some important considerations in the choice of mining method are : 1) Depth of cover over the coal seam. 2) Strength and thickness of rock strata in the overburden. 3) Characteristics of the coal seam, including thickness, nature and location of impurities or irregularities, dip (or pitch), nature and direction of cleavage, hardness, and structural strength of the coal. 4) Nature and strength of the immediate roof (top) over the coal seam. 5) Nature and strength of the floor (bottom) under the coal seam. 6) Presence and amount of explosive gas (methane). 7) Quantity of water likely to be encountered in the mining operation. 8) Any previous or concurrent mining in seams above or below the coal seam to be worked. 9) Any restrictions on recovery required for subsidence control. Topographical and geological reports and maps of the area are usually available from state and federal geological surveys, and contain excellent general information to guide more detailed investigations. Exploratory drilling, and the plotting and analysis of the information thus obtained, are essential steps in any development program, and aid in the correlation and evaluation of information gained by other means. Other good sources of information are operating coal mines that may be in the same seam in nearby properties. Such mines may indicate in advance much about roof control, drainage, ventilation, and other mining problems.

Jan 1, 1981

By Bradford F. Townsend

A study was made on six collapses that occurred during large-diameter tunnelling through weak sedimentary rocks and soil using SES methods in three stages?top heading, bench and invert. The collapsed lengths are between 20 m and 277 m. The collapses were re-mined using essentially the same tunnel-ling method with larger excavation profiles to accommodate the designed remedial measures consisting of ground treatment, pre-support and stronger initial support/outer lining required to carry higher ground loads acting in the collapsed lengths. The paper presents information on the collapses and the design and execution of the remedial measures.

Jan 1, 2008

By D. W. Scott

Ontario has a diverse industrial mineral resource base including abundant resources of structural industrial minerals such as sand and gravel, crushed stone, building stone, clay, shale, limestone and dolostone. These resources are used in the production of aggregates, brick, metallurgical stone, fillers, lime, cement and other construction materials. The majority of the operations are in deposits of Paleozoic and Quaternary age in southern Ontario, close to the major markets. Province-wide, there were over 140 million metric tonnes of aggregates produced in 1985, approximately 115 million tonnes of which was produced in southern Ontario with the remainder being largely from Crown land in northern Ontario. The structural industrial minerals account for over 80% of the value of total industrial mineral production, with the remaining 20% of the value king accounted for by the non-structural minerals being led by salt which is produced in southwestern Ontario. A host of other non-structural industrial minerals are known but production is currently restricted to calcite, gypsum, quartz, talc, nepheline syenite and by-product metallurgical sulphur products (Fig. 1). Location and Market Area Major production is in the area closest to the large markets of urbanized southern Ontario and the northeastern and north-central United States. In general, with the abundant variety and widespread resources of industrial minerals and the large population within 400 miles of most deposits, the market offers great potential. Ontario's 9 million population accounts for about 35% of the entire gross domestic product of Canada of $476.361 billion dollars in 1985. This equates to about 113 of the nation's buying power being within a 200 km (125 miles) radius of Toronto. This major concentration of industrial and economic activity has resulted in a well developed industrial minerals industry fulfilling most of the structural industrial minerals demand in Ontario, as well as a subsidiary demand in neighbouring provinces and states.

Jan 1, 1987

By M. R. Haibach, M. L. Shema, J. M. Silvis

"Since 2005, longwall coal mine operators in Pennsylvania (US) have been required to collect extensive hydrologic and biological data to document pre- and post-mining conditions of aquatic resources (streams and wetlands) overlying the subsidence control plan areas. Continued operation of the longwall mine is dependent upon empirical data demonstrating that the undermined aquatic resources have either been maintained or restored to an accepted range of pre-mining conditions. This study used quantitative hydrologic methods and comparative biological metrics to examine response of aquatic resources to longwall subsidence at the Bailey Mine located in Greene County, Pennsylvania. This study analyzed data from over 25 miles of streams and over 8 acres of wetlands that traverse the 4,779-acre study area. Hydrologic analysis of flow intermittency suggested that there are variable degrees of change to headwater streams immediately following mining; however, the majority of the effects are reversible through streamflow mitigation measures. Furthermore, the post-mining discharge from streams can be restored to within the range of pre-mining conditions the majority of the time. Biological assessments showed that greater than 95% of assessed stream length has maintained its ability to support benthic macroinvertebrate communities following mining and intervention (i.e., mitigation). Comparative metrics of the benthic macroinvertebrate communities showed that the biological community in 48 of the 50 sample sites is being maintained or restored across both high- and low-gradient streams. The effectiveness of intervention was further substantiated by the similarity in recovery times between streams having no intervention (median = 2.1 years, 95th percentile = 4.9 years) and streams with intervention, when recovery times were measured from the date of the intervention (median = 1.7 years, 95th percentile = 4.7 years). Changes to individual wetlands were observed between the pre- and post-mining assessments, but cumulatively a net gain of 7% in wetland acreage was realized. Hydrologic assessments were used to infer whether there was a potential that streams had been affected by mining; however, the ultimate test of stream recovery is based on biological metrics that establish the relative quality of the biological communities following mining. Overall, the hydrologic balance is being protected and the aquatic life use of streams is being maintained within the Bailey Mine’s subsidence control plan areas."

Jan 1, 2017

By Yun Bai, Sarah Wilson, Michael Salcher, Mark Trim

Over the last decade more than 62 miles (100 km) of civil transport tunnels were constructed in Sydney, Australia, using the sequential excavation method (SEM). The WestConnex motorway tunnels, each stage of which used over 20 roadheaders to excavate up to 40 tunnel headings, had numerous caverns up to 100 feet (30 m) wide and 82 feet (25 m) high. SEM tunnels in North America typically have far fewer active headings. This paper examines the differences in scope and risk allocation for construction phase services, including comparison of the Permit to Tunnel (PTT) process in Australia and the Required Excavation and Support process in North America.

Jun 23, 2024

By James J. Anthony

High-angle in-pit conveying is an idea that is being seriously studied by a number of important mining companies in North America. Its application in coal, iron ore, and copper mining is expected to reduce mine operating costs considerably compared with the conventional discontinuous methods, such as truck haulage, which are fuel, labor, and maintenance intensive. Therefore, a mine introducing high-angle in-pit conveyors will gain a competitive advantage over mines which continue to use conventional haulage. While the capital outlay for in-pit conveyor systems obviously varies depending on pit depth, the angle of incline, and the capacity required, it generally will not exceed that of truck haulage when all Factors are taken into consideration. These factors include the cost of excavation, as measured in relation to the volume of minerals mined, the cost of building truck ramps and roads, and the capital outlay for the trucks and maintenance facilities. In many cases, in Fact, the capital outlay will be less than for truck haulage. This cost advantage will best be realized by new mines, whereas in existing producing mines the switch from truck haulage may involve the abandonment of a substantial capital asset.

Jan 1, 1983

The fundamental objective of mine plans are usually to maximize the mine profit by extracting ore at the lowest possible cost over the mine life while some technical constraints are satisfied. Since the costs associated with the operation of trucks and shovels as resources are significant, determining the optimum number and allocation of these resources is an essential issue. This paper presents a Mixed Integer Linear Programming (MILP) model to determine the optimum number of shovels and trucks required to meet the short-term plan?s goals. Also, the model takes into account the allocation of trucks and shovels to mining faces. This model minimizes operational costs, while attempting to meet the production demand and to satisfy technological constraints. This paper also analyzes the operations of trucks and shovels in an open pit mine using ARENA simulation software.

Jan 1, 2012

By William C. Baldwin

Unitization and containerization continue to grow with great rapidity throughout the world today. Every industrial nation outside of the Iron Curtain is devoting more and more time toward research of these developing sciences. Unitization and containerization are proving to be the solution to many of modern industry's most pressing handling and shipping problems. Manufacturers make large savings, carriers receive many benefits, and customers take an increasing interest in demanding that their shipments either be unitized or containerized. Unit-loads consist of items, packages or bulk materials pre-assembled into a convenient mass for handling by mechanized equipment and to fit the internal dimensions of carriers. It has been found that unitized handling and shipping offers cost savings too great to be ignored by anyone interested in the distribution of goods. At present, the benefits from unitized shipping and handling are being enjoyed only to a small extent due to the failure of many persons concerned with handling practices in recognizing only some of the advantages of unitization. Before the full benefits of unitized handling and shipping can be realized, some major changes in packaging and distribution practices will be necessary on the part of industry. Numerous investigations in the last two years show conclusively that there are more advantages and more inherent savings for shipping goods on pallets in unit loads than by any other method. There is no question that unit-load handling can offer significant advantages to the user over piece-by-piece package handling. Reduction in handling costs is the primary objective of such activities, but it is by far not the sole objective. Some of the other benefits that can be realized are:

Jan 1, 1973

By E. R. Spencer

An assessment of U.S. western hard-rock miners? noise exposures was conducted as part of a multi-year National Institute for Occupational Safety and Health (NIOSH) survey of noise exposures in each sector of the mining industry. Noise from selected mining equipment and operator noise exposures were measured, analyzed, and tabulated for dissemination to the participating sites and are being used to direct NIOSH research and interventions to address the greatest noise hazards. Eighty-two noise dosimeter measurements were obtained, along with time-motion studies as the miners operated hard-rock mining machines. Ninety-six percent of the operators had daily noise doses that exceeded the Mine Safety and Health Administration?s permissible exposure level. The average gold miner dosages while operating the following equipment were: haul trucks - 261%, load-haul-dumps (LHDs) - 235%, single boom drills - 221%, bolters - 214%, and dual boom drills - 163%. The worst exposure level was a silver miner with a daily dose of 873%. Time-motion data showed that this miner?s exposure accumulated most rapidly while operating a jack-leg drill. These results will be used to help prioritize noise control development by NIOSH and other partners. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By T. C. Eisele

The use of column flotation was considered for the ?reverse flotation? of iron ore, where the gangue (quartz) was recovered in the froth product. This use of the froth for carrying the gangue mineral rather than carrying the valuable concentrate significantly changes the operational requirements of the column. The objective of this work was to determine which of several column flotation technologies would be most suitable for this type of flotation operation. Studies were carried out using both the Jameson column and the Deister column. Comparative results are presented that show the capabilities of both column types in this application relative to conventional Wemco flotation cells. Columns were demonstrated to have grade-recovery performance superior to what could be achieved with conventional cells. Two-stage flotation with the columns could produce a concentrate that was up to 70.2% Fe at 87.5% iron recovery, compared to 70.4% Fe at only 77.7% iron recovery for four stages of flotation in conventional cells. It was shown to be particularly important to operate the columns to recover a maximum of the quartz gangue into the froth. It was noted that there are often problems in scale-up of laboratory columns to plant scale, because the increase in height and the decrease in the ratio of height to diameter at the larger scale allows more axial mixing and bubble coalescence, both of which degrade the column performance. Horizontal baffling was shown to improve column performance by reducing axial mixing and breaking up large bubbles, and so the use of such baffles in the reverse flotation application was investigated.

Jan 1, 2007

By Susan L. Bednarz

Recent advances in digital cameras and image processing allow photographers to produce excellent high-resolution action shots in low light and high contrast conditions commonly encountered underground. Digital photography is often used for construction and inspection documentation for underground structures. Designers, owners, and contractors benefit from quality photographs that document incremental progress and project milestones. Documentation photos serve as a lasting record of as-built conditions, are an important marketing tool, and help the owner build public support for expensive public works projects. When the project is complete, the only mementos that the participants will hold onto are the photographs.

Jan 1, 2008

By Steven W. Hunt, Safdar A. Gill

Design and construction of temporary shafts for underground facilities often require evaluation of bottom stability due to rupture (blow-ins) caused by water pressure acting on a bottom plug. This paper provides an overview of shaft bottom stability evaluation methods for the case of a relatively watertight soil plug which overlies an artesian aquifer. Methods of considering plug perimeter shear, plug buckling and pressure relief are discussed. Minimum factors of safety are suggested. Future use of the shaft subgrade is also considered. Bottom plug failure case histories at several shafts are evaluated. This paper should be useful to project designers, ground support system design engineers and contractors involved with construction of shafts for underground facilities

Jan 1, 1997

By F. Wendling, R. C. Nascimento, S. S. Wendling

"The objective of this research is to study the quality of blast-furnace iron ore pellets with binary basicity 1 fired on a pilot scale using the two main firing processes that are presently in use in the world and comparing them. Currently, the great majority of pellet producers use the traveling grate process because of its higher production capacity. In this study, the physical and chemical qualities of the pellet feed, limestone, anthracite and bentonite were determined and the amount of additives for a blast furnace pellet with the defined basicity was calculated. The physical properties of the green and dried pellets were determined accordingly. Produced pellets, after being fired on a pilot scale using traveling grate and grate kiln, were subjected to chemical analysis and physical testing. No significant difference was observed in the metallurgical quality — that is, reducibility index (RI), reducing disintegration index (RDI) and swelling index (SWI) — of the pellets produced by both processes. However, a comparison of cold physical tests — tumble and cold compression strength — shows improved quality of the pellets fired using the grate kiln process.IntroductionThe development of human civilization owes much to iron and steel (Sun et al., 2015). Iron is the most used metal in the world, and it is the main component of steel, which is present in materials for structural engineering, automotive and general industrial applications (Liu et al., 2014). Increased global demand has led to a decrease in the resources of ore with high iron content (Zhang et al., 2015), and currently 95 percent of the iron ore in China needs processing before smelting as its iron (Fe) content is only about 30 percent on average (Liu et al., 2014).Pelletizing is a process to economically agglomerate iron ore pellet feed into pellet form. After balling, green pellets are conveyed to the final step of the manufacturing process (Pena, 1982). The process is a multifaceted one, involving high temperatures, air flow gas turbulence and complex equipment geometry (Larsson et al., 2009). The pellets are fed into blast furnaces, which are now predominantly used in the extraction of iron. Ore processing also requires physical separation, including crushing, grinding and water removal (Sun et al., 2015).The increase in steel consumption favors the exploitation of low-concentration ores and the production of pellets (Halt and Kawatra, 2014). Pellet quality is affected by various factors, such as their physical and chemical characteristics and their temperatures and residence times in the furnace (Halt, Silva and Kawatra, 2015). Different geological settings lead to a wide range of different minerals (Graça et al., 2015).This work aims to generate important information for the pellet industry in the area of physical and metallurgical qualities of the agglomerates obtained by two processes: traveling grate and grate kiln."

Jan 1, 2017

By P. Eger

In 1991, LTV Steel Mining Company decided to close an open pit taconite mine in northeastern Minnesota, using a passive treatment approach consisting of limiting infiltration into the stockpiles and wetland treatment to remove metals. Over 50 million metric tons of sulfide-containing waste had been stockpiled adjacent to the mine during its 30 years of operation. Drainage from the stockpiles contained elevated levels of copper, nickel, cobalt and zinc. Nickel is the major trace metal in the drainages, and prior to closure annual median concentrations ranged from 1.5-50 mg/L. Copper, cobalt and zinc are also present but are generally less than 5% of the nickel values. Median pH ranges from 5.0 to 7.5, but most of the stockpile drainages have pH greater than 6.5. Based on the chemical composition of each stockpile, a cover material was selected. The higher the potential a stockpile had to produce acid drainage, the lower the permeability of the capping material required. Covers ranged from overburden soil removed at the mine to a flexible plastic liner. Predictions of the reduction in infiltration ranged from 40% for the native soil to over 90% for the plastic liner. Five constructed wetlands have been installed since 1992, and have removed 60-90% of the nickel in the drainages. Total capital costs for all the infiltration reduction and wetlands exceeded $6.5 million, but maintenance costs are less than 1 % of those for an active treatment plant. Since mine drainage problems can continue for over a hundred years, the lower annual operating costs should pay for the construction of the wetland treatment systems within seven years.

Jan 1, 1999

By J. Wickens

Haile Gold Mine is located near Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The relatively low grade and refractory nature of the deposit has been a challenge for efficient processing since the start of mining on the property. Early processing techniques included gravity separation and barrel chlorination. The last operation employed heap leaching in 1985 through 1992. After being closed and reclaimed for over 20 years, the property is poised to re-open and produce once again. In this chapter of the Mine?s legacy, flotation and ultra-fine grinding will be employed to achieve economic extraction of gold and silver from the pyrite. This paper briefly reviews some of the mine?s history, the metallurgical testing, the flowsheet and discusses design considerations. KEY WORDS: process plant, flash flotation, leaching, SMD, stirred media detritor

Feb 27, 2013

By Richard Hanke

Tunnel construction on the Brightwater Conveyance System?s East and Central contracts required ground modifications of the existing site soils, comprised of sandy alluvium to very dense glacial till, to assist with both hand-mined and TBM tunneling operations at vertical access shafts. The ground modification program was completed with a modified double fluid jet grouting system to construct continuous overlapping soilcrete columns to depths up to 94-ft below existing grade. This paper presents the sequence and methodology for the ground modification work and capabilities of jet grouting for structural support and groundwater control in the challenging soil profile present at the Brightwater Conveyance System Project.

Jan 1, 2008

By W. J. Schlitt

The development of forced aeration as an approach to enhancing copper sulfide leaching is traced from its earliest development up to present day operations using this technology. Both large-scale field tests and commercial operations are covered. The historical portion is preceded by an introductory discussion of the role of air (oxygen) in sulfide leaching. Sufficient aeration may be achieved via naturally induced convective airflow. However, cases are identified where this is insufficient, leading to retardation of the sulfide leach rate. For these situations, forced aeration may be beneficial. The historical portion of the paper focuses on the major field tests that have been conducted in Montana, Nevada and Utah, along with commercial operations in the United States, Australia, Chile and Peru. The paper concludes with some general comments about the applicability of forced aeration, which are based on the information developed to-date.

Jan 1, 2006

By Abhilash, S. Sarkar, T. Venugopalan, P. Meshram

"To explore blast furnace slag as a secondary resource for rare earth elements (REEs), blast furnace slag containing lanthanum (La), cerium (Ce), erbium (Er) and neodymium (Nd) in concentrations of 17, 16, 4 and 44 ppm, respectively, was processed with sulfuric acid while optimizing the parameters of acid concentration, temperature and pulp density. The experiments showed that recovery rates of 92, 36, 35 and 52 percent for La, Ce, Nd and Er, respectively, were achieved at 1 to 5 weight/volume (w/v) percent pulp density using particles smaller than 250 µm and treating with 1 M sulfuric acid for one hour at room temperature. Raising the temperature to 95 °C promoted the dissolutions of Ce and Nd to 89 and 84 percent, respectively, for the same 1 M acid concentration and one-hour duration at 5 w/v percent pulp density. Cyanex 923 was preferred over Cyanex 301 for the purification of REEs from leach liquor. In another route, the leach liquor was subjected to precipitation with 0.5 to 1 M oxalic acid, resulting in a product with 4 to 5 percent concentration of REEs.IntroductionRare earth elements (REEs) are important materials in numerous high-technology applications, but they have high supply risk, giving rise to the study of new sources. The recycling of REEs has been well researched, especially on a small scale, but has not been widely implemented. Less than 1 percent of REEs were recycled in 2011 (Binnemans et al., 2013). REEs occur in a large number of minerals in oxidic compounds, such as oxides, carbonates, phosphates and silicates, and are present as mixtures at 10 to 300 mg/kg concentrations in many rock formations, such as basalts, granites, gneisses, shales and silicate rocks. The most abundant REE in the Earth’s crust is cerium (Ce), at a concentration of 20 to 70 mg/kg, followed by neodymium (Nd) and lanthanum (La), with heavier REEs being less abundant (Binnemans et al., 2013). REEs occur in nature in their oxidized forms in salts and minerals due to their electropositive nature and high affinity for oxygen. The possibility of recovering REEs"

Jan 1, 2017