Search Documents

By B. J. I. Adair, K. R. Weller

The bulk scavenger tailing from Aberfoyle's Hellyer Concentrator, which represents about one-third of the total tailing, runs about 2.5-3 g/t gold and 140-200 g/f silver. Both values are very finely disseminated, particularly the gold. Aberfoyle wished to establish whether ultra-fine grinding followed directly by cyanide leaching could be applied to the tailing for recovery of gold and silver. The work comprised the determination of gold and silver recoveries as a function of grind size and leaching time, the specific energy consumption required for continuous wet grinding of the tailing to the specified product size in a small horizontal continuous stirred mill, and an estimate of the rate of media consumption. The maximum extraction of gold, 23.3% was obtained from the finest product, with the highest cyanide concentration and longest leach time, confirming earlier work. A similar result was obtained for silver. The specific energy requirement for milling rose from 27.7 kWh/t for a P80 of 8.1 um to 219 kWh/t for a Pea of 2.3 um. The consumption of ceramic media was about 1.6 g/kg of final product. An extensive QEM'SEM Trace Mineral Search on the unground tailing failed to identify any gold-bearing particles but did identify silver-bearing particles which displayed a variety of textural associations and liberation characteristics.

Jan 1, 1998

By L. Borsch

Geochemical laboratories are commonly criticized by geologists about poor analytical reproducibility and erratic anomaly patterns, especially when gold and trace metals from resistant minerals are reported. Geochemical analysis in mineral exploration is a compromise between high productivity on the one hand, imposed by large numbers of samples, and analytical precision and accuracy on the other. However, the physical properties of resistant minerals, such as cassiterite, gold, beryl, chromite, zircon and others, interfere with both of these requirements. Therefore, the degree of sample homogeneity that can reasonably be achieved in sampling and sample preparation must be considered. Subsequently, the understanding of its effects on analytical data quality and the consequences on data interpretation will provide a basis for understanding the problems common to exploration as an interdisciplinary science. Complaints about poor and inadequate analytical performance are not confined to exploration geochemistry. They are a common feature in mining and metallurgy and wherever sampling and analysis of "grains" are concerned - the "nugget" or "grain size effect." The "grain size" effect Poor analytical reproducibility is normal for gold and a well-defined group of other elements usually found in resistant placer minerals. Those who use and interpret geochemical data must realize and appreciate the chemical, the physicochemical, the physical and the mineralogical properties of the elements and their minerals. Especially for the "placer" minerals and their elements, such comprehensive interpretation is crucial. The most important factor to consider is the behavior of a mineral and its metal component(s) during weathering and their integration into the sampled medium, in exploration mostly sediments and soils. (Data interpretation for samples of water, gas, to a certain extent rock, follows different patterns.) A mineral may be chemically and physically stable or it may easily disintegrate physically or decompose chemically, or any combination of such processes, at varying degrees. The breakdown products, in turn, may or may not, interreact with the environment. If the nature of an element or a mineral predestines it for a heterogenous distribution in the sample medium, then nature, size and number of grains likely to occur should be considered in relation to the sample portion taken for analysis. This allows the estimation of their effect on analytical precision and accuracy. Elaborate and sophisticated statistical calculations exist on this subject. But these approaches do not cope with the complexity of the natural surface environment. The miner alogical, chemical and environmental behavior of elements and minerals can be estimated but not calculated. However, the mineral grain sizes and their influence on analytical precision can be precisely calculated if certain conditions, assumptions and idealizations are made. If the geochemical and mineralogical characteristics of minerals and elements are understood, such calculations demonstrate the grain (or nugget) effects that mineral properties and (geo)chemical behavior of minerals and elements cause on the precision and accuracy of geochemical analysis through their influence on sample homogeneity. Two other factors that influence the sample homogeneity and the nugget effect are the efficiency of sample preparation and the sample portion taken for analysis. In this way, certain element- or mineral-specific parameters can be established as a guide for the sampling program. The information, for example, may assist in determining sampling procedures in the field, especially the sample weight to be taken for "representative samples." Also, it may help assess whether analytical data, as provided by the laboratory, are acceptable. Finally, it may help determine the approach in data interpretation. However, all such simplified calculations are based on idealized, that is, unreal assumptions and conditions. As such, they represent one extreme end on the scale of probabilities. The reality is found somewhere away from this extreme, towards homogeneity. An example from a study of an eluvial gold prospect may be given for illustration: •Original sample weight: 20 kg (44 lbs) of rock gravel, crushed and ground to -0.18 mm (-80 mesh). •Au content: 20 grains of Au, average size of about 0.5 mm3 (0.03 cu in.) each = 7.5 mg each, making a total of about 150 mg Au in the sample = 7.5 ppm Au. Assumptions •Au occurs in the sample as free, discrete grains only. •Not more than one grain, if any, goes into each sample split (analyte) portion (20 grains of 7.5 mg Au each). •Analysis of original rock sample: 100 g sample for analysis, 20 kg/100 g = 200 samples 20 samples with 1 grain each: result, - 75 ppm Au. 180 samples with no grain: result, 0 ppm Au chances 1:9 •10 g sample for analysis:

Jan 1, 1996

By Diómedes Sarmiento

Centromin is a Mining Company owned by the peruvian government. It's considered as one of the major mining and metallurgical center in Latin America. The main operations of the Company are: Mining, Concentration, Smelting and Refining of several metals (Figure 1). At present, dentromin operates with six mining units: Cerro de Pasco, Morococha, Casapalca, San Cristobal, Yauricocha and Cobriza; which are located in the Central part of the country between 2 100 m and up to 4 800 m above sea level. The installed capacity of concentration all together ranges about 14 000 tons per day. There's also a metallurgical plant in La Oroya with a production capacity of 220 000 tons per year of refined metal. The production of the Company is diversified in twenty two (22) final pro- ducts, whose major productions are : copper, lead, zinc, silver, gold, tungg ten and bismuth. The minor products are: arsenic, antimony, cadmiun, teluriun, sulphuric acid, indium, selenium, etc.

Jan 1, 1979

By W. L. Price

The intelligent selection of wire cloth and perforated plate for screening surfaces seems a rather confusing subject to the newcomer in aggregate processing. The proper application of various screening surfaces is a complicated one and one could consider himself an expert only after many years of working with all applications. However, part of the subject matter could be simplified considerably for, the average screen user. In this paper an attempt will be made to do this, by presenting some comparative specification data along with cost figures Unfortunately, it is impossible in the limited scope of this paper to give actual service comparison records between different cloths or cloth and plate. Anyone who has considered making actual service comparisons for competing screening media is well aware of the almost insurmountable problems Their solution would form the basis for a separate paper on that subject alone. Therefore, this paper will be limited to comparative data up to the point of installation.

Jan 1, 1961

By K. A. Brame, L. G. Austin, R. S. C. Rogers

The breakage parameters of phosphate ore were determined by batch first-ordering grinding studies in a laboratory ball mill according to the Austin, Klimpel, and Luckie procedures. The results were scaled to five larger mills of 0.56, 0.82, 8.36, 4.41, and 5 m in diameter assuming equilibrium ball charges for the full-scale mills. The results were used to predict product size distributions and capacities for batch grinding in the smaller mills and open-circuit grinding in the larger mills. The predicted capacities were in approximate agreement with experimental values except for the 5-m diam mill. The Bond method gave capacity predictions that were 4570 to 150% too high.

Jan 1, 1987

By G. L. Smit

The Buffelsfontein Gold Mining Company is situated in the Klerks-dorp district of the Province of the Transvaal in the Republic of South Africa, approximately 100 miles west of Johannesburg. Gold production commenced in January 1957 and Uranium treatment of residue slimes as a by-product started in July 1957. The mining property is 5435 mining claims in extent, the equivalent of 7,988 acres or 12.5 square miles. The mine was initially exploited by the Pioneer Twin Shaft System, consisting of a 26 feet diameter down-cast shaft and a 22 feet diameter up-cast shaft, sunk in the north-west area of the mine to cater for the hoisting and ventilation requirements for a milling rate of 150,000 tons per month.

Jan 1, 1964

By William R. Yernberg

The 2002 Arizona Conference was held Dec. 8 and 9, 2002, at the Doubletree Hotel at Reid Park in Tucson. The annual conference is organized by the Arizona Conference Board of Directors, which represents SME sections in Arizona and adjacent areas. The conference provides an opportunity for individuals and corporations associated with mining in the region to get together once each year to discuss the status of the industry. The meeting featured a keynote address, a distinguished lecture and about 30 technical papers. As was the case at the 2001 meeting, the economy, the price of copper and foreign competition continue to be the hot topics of discussion among the attendees. The domestic copper industry still faces challenges due to low copper prices dictated by the world market and because of a weakened domestic economy. There continues to be concern about the Arizona region’s copper industry in light of the mergers, downsizing and shutdowns that have occurred during the past several years.

Jan 1, 2003

By F. M. Doyle, Jiang Tao, Xu Shi, Chen Jin, E. Peters

Tafel curve technique and leaching tests have been applied to study the kinetics of gold leaching with thiosulfate. Results show that cupric ions and ammonia play the part of catalysts in the leaching of gold with thiosulfate. The activation energy of gold dissolution is calculated as 27.99 KJ/mol in the absence of both cupric ions and ammonia. However, the energy is reduced to 15.54 KJ/mol in a solution of 0.01 mol/L Cu (NH3)2 4* and 0. 5moVL total ammonia. The reaction order of Cu (NH,) g is one in the range of 0.001~0.1mol/L. These results support the electrochemical-catalytic mechanism pro- posed by the authors and explains the behavior of cupric ion and ammonia (Jiang Tao, et al., 1993)

Jan 1, 1993

By Rusty Winn

"R.E. Janes Gravel Co. is an aggregates producer is located along a paleo-channel of the Ogallala formation (locally known as the Slaton Channel) approximately 48.3 km (30 miles) southeast of Lubbock, TX. In an attempt to beneficiate the 25.4-mm (1-in.) concrete aggregate product, a log washer was installed in the processing line to liberate and remove fines (clay) from the finished product. The introduction of this extra cleaning step increased fines in the finished product, exacerbating the original problem. Several other processing options were investigated before a geological analysis was undertaken to try and define the lithology of the formation and formation characteristics in an attempt to alleviate this problem.Initial assessmentsThe mined resources are mid-Miocene to early Pliocene (16-4 mya) in age and is the eastern exposure of the Ogallala formation of the Southern High Plains escarpment. The Ogallala formation consists of coarse-grained alluvial sediments in paleovalley channel ways from the Rocky Mountains with fine Aeolian and paleosol deposition on the uplands across the High Plains region of the United States. Locally, these Rocky Mountain sediments from New Mexico were transported and deposited in a paleochannel that is approximately 0.805 km (0.5 miles) wide and 15.25 to 18.3 m (50 to 60 ft) in depth. As this channel cut across the Southern High Plains it eroded local rock sources of Late Cretaceous limestones and Triassic sandstones and mudstones incorporating them into the younger Ogallala depositional sequence.Depositional historyThe channel currently being mined is a nontypical Ogallala deposit. The Ogallala in the panhandle of Texas is divided into two units, the Couch and the Bridwell. The Couch is the older of the two and exhibits alluvial sedimentation of thicker and larger gravel (up to 76.2 mm or 3 in.) deposits fining upward to Aeolian sedimentation and thick friable caliche deposits. The Bridwell overlies the Couch and is characterized by alluvial sedimentation, a distinctive red tint and smaller gravel components (typically no larger than 25.4 mm or 1 in.) fining upward to Aeolian sedimentation and thick, well-indurated caliche cap. The Slaton Channel divides these two units and shares lithologic components of both, yet is lithologically distinct due to its Cretaceous Age limestone gravels that can be < 3.66 m (12 ft) in size. Caliche/calcrete is a calcareous (CaCO3) deposit that forms in the B horizon of soils as a rain water leachate of CaCO3 from the upper A horizon."

Jan 1, 2014

By Lok W. Home

INTRODUCTION Today, raise drilling (boring) has become the stan¬dard method of raising throughout the Western world. It is estimated that the majority of raise footage com¬pleted in 1977 was accomplished by the raise drilling method. Extensive replacement of the drill and shoot system by mechanized raise drilling has occurred be¬cause users have recognized one or more of the follow¬ing advantages. In a direct cost per meter comparison, mechanized raise drilling is economically more attractive than drilling and shooting. Mechanized raise drilling offers improved personnel safety over the drilling and shooting method. Mechanized raise drilling is a faster and more predictable method for excavation than is drilling and shooting. The raise cost per unit of length becomes less as the raise length increases, offering greater flexibility in the overall design of mines. Mechanized raise drilling provides a substantial reduction in labor requirements. 6) Mechanized raise drilling improves the working environment. 7) Mechanized raise drilling improves the rock in¬tegrity of round, unblasted raises. Increasing acceptance of the raise drilling technique is enhanced by continuing equipment development. Today, a wide range of machines and capabilities is available, machine drive systems have been improved, reliability has been increased, and cutter technology is being improved quite rapidly. Table 1 lists the four major manufacturers of raise drilling machines, cutters, and reamers, together with the approximate number of machines that each company had in operation at the end of 1977. Although Reed and Smith are major suppliers of reamers and cutters, they do not manufacture the drilling machines. Four or five other relatively minor suppliers have built machines, reamers, and cutters for raise drilling, but they did not have a substantial num¬ber of machines in the field at the end of 1977. MACHINES FOR MECHANIZED RAISE DRILLING There are three principal arrangements for making machine-bored raises. They include the use of standard raise drills, reversible raise drills, and blind-hole or box¬hole raise drills. Standard Raise Drills The standard raise drilling machine is set up on one mine level or on the surface, and a pilot hole is drilled from that level or surface to a level below. When the pilot hole has been drilled, the raise then is reamed back from the lower level to the upper level or the surface. This arrangement is illustrated in Fig. 1. Reversible Raise Drills The reversible raise drilling machine is set up on a lower level of the mine, and a pilot hole is drilled up¬ward to a higher level. The raise then is reamed back from the upper level to the lower level. This arrange¬ment is illustrated in Fig. 2. The machines used for this type of raise drilling normally are capable of being used as standard raise drills. Blind-Hole or Boxhole Raise Drills The blind-hole or boxhole raise drilling machine is set up on a lower level of the mine, and a full diameter raise is bored to a higher level without the use of a pilot hole. This type of machine is illustrated in Fig. 3. Drill Recommendations If access to upper and lower mine levels is equal, the standard raise drill should be used. The complexity of the equipment and associated handling procedures for boxhole drilling far outweigh any mechanical advantage or reduction in the number of operations, provided that access to an upper level is available. If there is good access to a lower level but only limited access to an upper level, the use of a reversible raise drill should be considered. If there is no access to an upper level, a blind-hole or boxhole raise drill is the only practical mechanized system. MACHINE SELECTION There are six major considerations in selecting a machine for raise drilling. These include operating range, cutter loading, machine structure and main¬tenance, drill string configuration, drive system, and automated controls. Operating Range As shown in Table 2 and Figs. 4 through 6, raise drilling machines are available for a wide range of hole sizes. Standard raise drill ratings range from raises of 0.9 m (3 ft) diam and 120 m (400 ft) length up to raises of 3.5 m (12 ft) diam and 900 m (3000 ft) length. Boxhole raise drilling machines are available for raises ranging from 0.9 m (3 ft) to 2 m (6 ft) diam with lengths up to 90 m (300 ft). Table 2 lists, among other criteria, the torque and thrust of typical machines; torque and thrust are the main criteria for analyzing the capacity of a machine. The raise sizes shown in Table 2 assume a condition of medium hard to hard rock formations and optimum cutter loading. The recommended raise size for a given machine can be exceeded when raising softer rock formations or when the operator is willing to accept a lower level of performance; the performance is related directly to the 1093

Jan 1, 1982

By A. B. Van Cleave

It was first pointed out in 1934 by Gaudin (1) that the "oily" oxidation product of the alkyl xanthate ion-dialkyl dixanthogen, might be the "active flotation agent" on sulphide minerals and there have been a number of studies supporting this hypothesis (2,3,4). However, all of these studies have relied largely on electrochemical evidence. Galena, being a semiconductor, may be used as an electrode in aqueous solution and it was shown that ethyl xanthate ion does not adsorb with charge transfer in the absence of oxygen unless the potential of the galena surface is above -100 mv versus the hydrogen electrode (H2 E). At this potential the galena surface is slightly hydrophobic but does not become strongly hydrophobic unless the potential is raised to 210 mv (versus H2 E). It is suggested that, at potentials of 210 mv or above, ethyl xanthate ions are oxidised to diethyl dixanthogen and that chemisorption of oxygen raises the galena surface to this potential. On the other hand, examination of xanthated galena surfaces by chemical or physical methods (5,6,7) has failed to detect dixanthogen and it has been shown that dixanthogen may be reduced to lead xanthate at a lead sulphide surface. (5,8)*. It was suggested by Leja and Poling (5) that, as dixanthogen is a neutral molecule it would not be repelled by the negatively charged galena surface so that the adsorption was envisaged as taking place through homogeneous oxidation of the xanthate ion to dixanthogen, adsorption and reduction of the dixanthogen to a chemisorbed lead xanthate species. In paper I of this series (11) it was shown that the thiosulphate ion, which forms on galena surfaces in slurries at the pH normally used for flotation, will reduce dixanthogen. There is, therefore, the impasse that the electrochemical evidence requires that xanthate ion be oxidised to dixanthogen at the galena surface while the chemical evidence shows that the reverse reaction takes place.

Jan 1, 1973

By Dermot Winters

The Surface Mining Control and Reclamation Act (SMCRA, or the Act) was enacted on August 3, 1977. The Act was written, in part, to put an end to uneven environmental standards and to establish minimum national standards. Certainly, one of the motivating factors for passage of the Act was the success of the Federal Coal Mining Health and Safety Act of 1969 in reducing deaths and injuries in the coal industry nationwide. Section 516 (b) (1) of the Act requires *that subsidence be prevented from causing material damage to the extent technologically and economically feasible except in those instances where the mining technology requires planned subsidence in a predictable and controlled manner. Section 516 (c) of the Act authorizes the regulatory authority to suspend underground mining if there is imminent danger to inhabitants of urbanized areas, cities, towns, and communities. On December 13, 1977, the interim program, which applies a portion of the performance standards of the Act, was promulgated. Then on September 18, 1978, the proposed permanent program was published for public comment. Finally, on March 13, 1979, the final permanent program was promulgated and the States were given a period of time to submit their programs for approval.

Jan 1, 1986

The Mining Foundation of the Southwest will hold its 15th annual American Mining Hall of Fame Awards banquet on Saturday, Dec. 6,1997 in Tucson, AZ, preceeding the Arizona Conference of SME. The Mining Foundation&apos;s Hall of Fame, located in Tucson, recognizes outstanding contributions to the mining industry by individuals and industry partners. A permanent display of honoree vitae is located at the Arizona Historical Society at 949 E. Second St. in Tucson. Each year, one living award recipient and up to two honorees from mining history are chosen by the Hall of Fame committee and the board of governors of the Mining Foundation. In 1989, the Mining Foundation also initiated a Medal of Merit to recognize outstanding individual technical and professional contributions to the mineral industry. And in 1995, an award was instituted to recognize contributions made by companies and organizations in partnership with the mining industry. This year&apos;s inductee is James R. Moffett, chairman and chief executive officer of Freeport-McMoRan Copper and Gold Inc. He will be present as guest of honor and featured speaker. The Hall of Fame will induct John V. Dorr, metallurgist and chemical engineer. Also inducted will be Frederick L. Ransome, a geologist. Medals of Merit will be awarded to Hugo T. Dummett, senior vice president, Exploration BHP Minerals, and Spencer R. Titley, professor in the Department of Geosciences at the University of Arizona. An Industry Partnership Award will be presented to the Colorado School of Mines for its continued support to the mining industry through education and research. The banquet will be held at the The Westin LaPaloma in Tucson beginning with cocktails at 6:30 p.m. Tickets are available from Clare A. Roscoe, manager, Mining Foundation of the Southwest, telephone 520-577-7519, fax 520-577-7073.

Jan 1, 1997

By M. J. Miller, N. Ripepi, M. Karmis, J. M. Conrad

Unmineable coal seams present an opportunity to sequester carbon dioxide emissions from power plants, while enhancing the recovery of coalbed methane. Injected carbon dioxide is adsorbed and stored on the coal surface while releasing methane that can be commercially recovered. Carbon sequestration, therefore, allows the utilization of unexploited mineral resources while reducing “greenhouse” gas emissions. This paper presents the feasibility, efficiency and enhanced recovery potential of coalbed methane production using carbon dioxide sequestration in the Central Appalachian Basin. The focus of research is on geological characterization of unmineable coal seams in Central Appalachia and the corresponding carbon dioxide storage capacity. Virginia Tech and Marshall Miller & Associates, Inc. conducted this research under the Department of Energy’s Southeast Regional Carbon Sequestration Partnership program.

Jan 1, 2006

By Lee Ann Arrington-Webb

Thiele Kaolin Co. has invested much time and money in achieving and maintaining its IS0 9002 certification. Through a regimen of process control and documentation, routine audits and a commitment to quality management, this kaolin producer is a competitive pigment supplier in a worldwide market. Background In 1987, the International Organization for Standards developed the ISO 9000 quality management system. This series of standards is used as a means to ensure customers that a quality management system is in place. Certification of a company does not mean that an individual product is of high quality. Rather, it demonstrates a supplier&apos;s ability to meet its customers&apos; product and service needs. It also shows that a company has documented records to assure product consistency. The ISO 9000 system was begun in England during the early 1980s. During the mid-1970s, the British manufacturing industry was experiencing low quality. In an attempt to boost quality standards, the British government established the BS 5750 standards system. In 1987, BS 5750 was incorporated into ISO 9000. The ISO 9000 series consists of three levels of certification. ISO 9001 is the model for quality assurance in "design/development, production, installation and servicing." This standard applies to companies that rely on research and development to bring products that frequently change to market. ISO 9002 involves "production and installation" only. This standard is relevant to industries that produce a specific product according to specifications - either their own or their customer&apos;s. ISO 9003 is the model in "final inspection and test." This standard is the least detailed of the 9000 series. It is also the most applicable to companies that purchase, inspect or sort and resell. The quality system requirements for certification are outlined in the 18 elements of ISO 9002. These include: 4.1 - Management responsibility. 4.2 - Quality systems. 4.3 - Contract review. 4.4 - Design control. 4.5 - Document and data control. 4.6 - Purchasing. 4.7 - Control of customer-supplied product. 4.8 - Product identification and traceability. 4.9 - Process control. 4.10 - Inspection and testing. 4.11- Control of inspection, measuring and test equipment. 4.12 - Inspection and test status. 4.13 - Control of nonconforming product. 4.14 - Corrective and preventive action. 4.15 - Handling, storage, packaging, preservation and delivery. 4.16 - Control of quality records. 4.17 - Internal quality audits. 4.18 -Training. Continuous improvement, though implied in maintaining these requirements, could potentially be included in the quality system requirements in the next revision. The ISO 9000 requirements and documentation system is shown in the hierarchy pyramid (Fig. 1). A company&apos;s quality policy serves as the top of the pyra-

Jan 1, 1997

By R. A. Hevia

Florida Power and Light is the fifth largest investor-owned electric utility in the country. It has a service territory that covers 35 counties, or 28,000 square miles, 2.5 million customers, and serves 5.6 million people. The total installed capacity is 13,470 MW, generated by four nuclear units, 36 oil and/or gas fired units, and 48 gas turbine units. Traditionally, FPL has been an oil-based utility. In 1979, this dependency on oil became obvious when 42 million barrels of oil were burned during the year. At that time, it was also projected that, based on the current estimates of customer growth and available generation capacity through 1990, FPL&apos;s residual fuel oil consumption would increase from the 1979 level of 42 million barrels (6.7 million m3) per year to approximately 55 million barrels (8.7 million m3) per year by the mid-1990&apos;s. Concern over this was further aggravated by the fact that it was difficult to estimate both the price and quantity of fuel oil that would be available over the next decade since changes in the world market, decisions by oil producers and refiners, and international political developments would all affect the availability of oil. Also, at that time, the price of residual fuel oil had increased drastically, and there was no reason to think that these prices would soon stabilize. Thus, oil back-out became a primary objective of FPL and since then, FPL has been actively investigating ways to decrease fuel oil consumption.

Jan 1, 1985

By V. Nasri, S. Rashidi

The Baltimore Red Line Project is a proposed 22.7-km (14.1-mile) long east-west light rail transit (LRT) line envisioned to connect the areas of Woodlawn, Edmondson Village, West Baltimore, downtown Baltimore, Inner Harbor East, Fells Point, Canton and the Johns Hopkins Bayview Medical Center Campus. The Red Line LRT System has two tunnel segments - the Cooks Lane Tunnel (CLT) and the Downtown Tunnel (DTT). The CLT segment is roughly 1,920-m (6,300-ft) long. It commences at the west portal located at the highway ramp for I 70 (to be removed) and terminates at the east portal that is at the intersection of Edmondson Avenue (U.S. Route 40) and Glen Allen Drive. This segment of the project consists of the following construction components: approximately 1,458 m (4,786 ft) of tunnels, 143 m (469 ft) of cut-and-cover tunnel, and 318 m (1,045 ft) of retained cut (U) section. The approximate horizontal alignment for the Red Line LRT Project is shown in Fig. 1.

Jan 1, 2014

By H. R. Coles

Test work conducted in the 6.4 and 10.52 m Aerofall Mills at the Iron Ore Company of Canada Carol Project showed that the conventionally used ?deflector?-type liners which form the basic principle of Aerofall Mill grinding did not necessarily provide the best grinding performance. A new design, using low profile liners incorporating radial ribs of a proper height, actually improved the mill throughput in the order of 9 to 20% without sacrificing grinding efficiency. In addition, the new design reduced liner weight and scrap losses, which resulted in a reduction of liner consumption by 25%. It provided better protection to the mill shell and reduced the overall maintenance cost for the mill

Jan 1, 1980

By X. Cheng

The mechanism of cathodic decomposition of pyrrhotite was studied in deoxygenated solutions at natural, near neutral pH using potential and cyclic voltammetric measurements. Reaction products on pyrrhotite surfaces were examined by AES and XPS, and by analyzing the voltammograms for the electron balance of the reactions. Surface properties of the pyrrhotite/solution interface were characterized using ac impedance technique. The parameters of an equivalent circuit were determined by the nonlinear least squares fit (NLLSF) technique. The effect of cathodic polarization on floatability was investigated by micro-flotation tests. Possible implications to the flotation separation of chalcopyrite-pyrrhotite ores are discussed.

Jan 1, 1993

By Greg Sanders, Bill Lueck, Michael Gilbert, Mahmood Khwaja

"The city of Minneapolis contracted with CDM Smith to update and provide a conceptual design for improvements to mitigate surcharge flooding in the Central City Storm Water Tunnel System (CCSTS). As a part of the project, CDM Smith conducted a field survey and condition assessment of the existing tunnel system. Information from the survey was then used to update the existing XPSWMM model and develop system wide alternatives.The CCSTS provides storm-water runoff drainage for nearly the entire area of the city’s downtown commercial district. The system consists of deep storm-water tunnels constructed in the St. Peter Sandstone, approximately 21 m (70 ft) below the street’s surface. The primary tunnels comprising the Central City storm water tunnel system are located below Hennepin Avenue, Nicollet Mall, Lesalle Avenue, Marquette Avenue South, 2nd Avenue South, South 5th Street, Washington Avenue South, Portland Avenue South, 2nd Street South, and Chicago Avenue South, as shown in Fig. 1. This network of tunnels conveys the runoff from a 305-acre tributary area that is generally bound by Hennepin Avenue and 1st Avenue North to the east, 12th Street to the south, 4th Avenue South and 7th Avenue South to the west, and 2nd Street South. These tunnels were constructed between 1936 and 1940, except for the Marquette Avenue South tunnel, which was constructed between 1963 and 1964.The CCSTS operates as a gravity flow system. These tunnels were constructed within the St. Peter Sandstone layer of bedrock and emerge from the bedrock at the Mississippi River below St. Anthony Falls. The Central City and the adjacent Chicago Avenue tunnel system converge into a single outfall at the Mississippi River. The runoff discharges from the converged outfall to a side channel of the Mississippi River, called a tailrace, located near the Guthrie Theater. The Minneapolis Division of Surface Water and Sewers provided 32 historic plats detailing the plan and profile of the tunnel system.The tunnel plans show nine different cross-section configurations. Eight configurations within the overall system generally show the same geometric “cathedral” shape with the inside dimensions varying from 1.2 to 1.8 m (4 to 6 ft) in width and 1.8 to 2.4 m (6 to 8 ft) in height. For analysis, these eight configurations were reduced to three configurations with regards to tunnel liner, cross-sectional area and support. For simplicity, the three configurations are described according to the three types of tunnel support used during construction: none required, light timber and heavy timber"

Jun 1, 2019