Search Documents

By S. T. L. Harrison, M. A. Fagan-Endres, M. D. Odidi

This paper investigated the ability of eight common hydrodynamic models – tanks in series (TIS); three compartmental model configurations (Comp-1, Comp-2 and Comp-3); advection dispersion (AD); piston exchange (PE); piston exchange-diffusion variant (PE-D) and piston dispersion exchange (PDE) – to simulate residence time distribution (RTD) data generated from tracer tests conducted on a packed bed composed of different size fractions of malachite ore. The chosen materials were packed into 0.1 m internal diameter columns to a depth of 0.155 m and drip irrigated at 5.11 L/ m2.h. The four size fractions tested were: 1 – 2 mm, 2 – 2.8 mm, 4.75 – 5.6 mm and 13.6 – 16 mm. Step-up tracer tests were conducted using potassium chloride. The results showed that an increase in the particle size of the malachite ore had little effect on overall bed porosity but resulted in significantly lower values of liquid holdup. Two of the monoporosity models tested, TIS and Comp-2, were the most affected by the changes in bed size fraction due to their inherent inability to cope with high degrees of non-ideal flow present in the larger particle systems. The dual porosity models performed relatively better with the dominant trend being a reduction in dynamic to total liquid holdup as particle size increased. Of all the models tested, the PDE and TIS models were the best and worst performers respectively, with R2 values averaging at 0.997 and 0.679 across all experiments respectively. Though the Comp-1, Comp-3 and PE-D models also performed well, the addition of the dispersion coefficient to take the axial spread of fluid molecules into account added a layer of complexity that allowed the PDE model to perform relatively better than the other dual porosity models. Keywords: Heap leaching, packing material, hydrodynamics, malachite, PSD, modelling

Jan 1, 2020

By C. Kasatuka

Globalization creates investment opportunities for enterprises around the world. Attracting foreign investment has been a key challenge for economic growth in developing countries. Corruption, political instability, armed conflict, and other internal problems affect foreign direct investment (FDI) inflows negatively. A framework of criteria provides a basis for comparing non-commercial risk (NCR) among twenty-three mineral economies. Countries competing for foreign direct investment inflows are ranked from least to most risky. This study compares Inward FDI Performance Index (IND) with NCR ratings in developing countries and shows that risk is increasingly mitigated by means of appropriately structured insurance. Given the option for countries with similar mineral potential, investors will generally invest in the country that offers lower non-commercial risk. Keywords: foreign direct investment, non-commercial risk, developing countries.

Jan 1, 2006

By C. Swart

Automation technologies are increasingly adopted in different mines world-wide. This paper presents the technical aspects of vehicle automation applications at two Noranda operating mines. Teleoperation of 5 LHDs at Noranda?s Bell Allard mine is used in order to meet aggressive mining requirements under difficult conditions. The equipment is performing under high demand for reliability and performance. In order to further increase performance, automated loading has been commissioned on one of the LHDs and is being tested. Results to date indicate improved performance with respect to an operator through better filling of the bucket, fewer passes at the muck pile and shorter cycles. Noranda?s Brunswick mine is currently commissioning an automated haulage zone where two optically guided trucks transport ore from a remotely operated chute to two ore passes. Expected operational advantages include increased system capacity and enhanced safety and comfort for the operator. Monitoring to date indicates that the trucks can operate reliably under the conditions imposed by mine production.

Jan 1, 2002

Mining is an inherently risky business; from the technical, environmental, social, and economic uncertainties associated with advancing an exploration prospect to a viable project to the operating, market, and safety risks and uncertainties attached to a developed mine. Since we cannot totally escape the risk and uncertainty related to resource projects, as an industry we should improve our presentation of the upside and downside risks in the context of the project?s development path and maturity. More transparent, consistent, and balanced views of technical confidence will better inform both internal and external stakeholders about the expected risk in the project. International reporting codes set out the minimum standards, recommendations, and guidelines for public reporting of Exploration Results, Mineral Resources, and Mineral Reserves. However, the reporting code principles of transparency and materiality are largely subject to the interpretation of the competent person(s), which may introduce a degree of subjectivity in reporting, particularly the level of disclosure regarding supporting information. It is fundamental that Mineral Resources, Mineral Reserves, and study outcomes are reported so as to unambiguously present the level of inherent technical uncertainty (or confidence) in a project, while conveying a balanced view of the opportunities a project presents. Reporting needs to consider various stakeholders who may rely on this information, and present the data in the context of the changing risk profile associated with project development paths and project maturity. This paper discusses the interdependence of resource-to-reserve conversion, the consideration of various technical-economic study types, and the level of confidence conveyed to stakeholders relying on these technical reports and other company public announcements.

Jan 1, 2014

By L. Li

The performance of microemulsified diesel and conventional diesel collectors in coal flotation was compared by flotation indicators, including combustible recovery, ash content of the clean coal, and the flotation index. An efficient separation with lower dosage was obtained using the microemulsified diesel collector. Under optimum separation conditions, the microemulsion consumption was 100 g/t less compared with diesel. The saving in diesel consumption using the microemulsion reached about 70%, disregarding the consumption of the surfactant and cosurfactant. Frothing tests showed that the frother dosage was decreased by using the microemulsion collector, because of the surfactant and cosurfactant added during preparation. The microemulsified diesel collector is superior to the conventional diesel collector in terms of diesel consumption and separation efficiency, but the selectivity requires further improvement. Keywords froth flotation, microemulsified collector, coal.

Nov 1, 2013

By S. T. Johansen, C. Colomb, B. Ravary

Combustion and thermal NOx formation have been modelled using the Computational Fluid Dynamics (CFD) commercial code Fluent 6.1. The aim was to predict and give a better understanding of the combustion in electric arc furnaces for the production of ferro-silicon and silicon metal. Another important objective was to assess the impact of a number of operating parameters on the NOx formation. The CFD tools used are de-scribed with a special focus on models for species and turbulence transport. Sensitivity studies have been carried out to study the influence of several parameters: sub-models, process gas composition and distribution at the charge surface and influence of the presence of SiO. The main conclusions are: ?Using the combination of a realistic design, boundary conditions and models, the simulated NOx level is in quantitative agreement with measurements. The presence of water vapor is particularly important because of its influence on the specific heat of the mixture and resulting temperature. ?Release of significant amounts of SiO from the charge surface results in an important increase of NOx, even if we applied a simplified combustion model for SiO gas. However, because of lack of thermal and compositional data for blowing situations (when SiO flows directly from the arc cavity through open channels to the charge surface), no quantitative validation is possible. The way SiO is distributed (uniformly or as a jet) has a limited impact on the result in our computations.

Jan 1, 2007

By B. J. Vorster

AngloGold South Africa region currently consists of twelve gold plants. These plants use a combined total of $20 million of cyanide per annum. Of this, the major portion (60%) is consumed at two Ergo dump retreatment plants. Historically the primary motivation for cyanide control at Ergo has been one of leach/cost optimization. However, more recently, with the increased public awareness of cyanide in the environment, a secondary but increasingly important motivation for control has been to ensure that only the minimum amount of cyanide is added to the process whilst not compromising leach performance. Following a brief overview of the Ergo process, the methodology in determining the amount of cyanide to be added is described. The paper then traces the developments in cyanide control from very basic manual systems to the current automated control system. In line with the increasingly sophisticated control systems, developments also took place in regards to the method of cyanide analysis. The development of these analysers is also discussed. Whilst cyanide is one of the major drivers, if not the major driver of gold dissolution, it cannot be viewed in isolation particularly with respect to the relationship between cyanide and oxygen as ascertained from the Elsner?s well-known equation. Consequently, in order to control cyanide addition, knowledge of the relative cyanide/oxygen profiles is necessary. Various means investigated at Ergo for pulp oxygenation have therefore been included for the sake of completeness. Finally a comparison is made of the control achieved from the current system compared to the original manual system. The knowledge and experience gained at Ergo is now being used to draw up guidelines for the installation and optimization work at the other AngloGold plants. The net effect of this will be reduced cyanide consumption for the region, which also, apart from the obvious economic benefit, translates into a reduced environ-mental risk.

Jan 1, 2001

By A. Nel

The gold mining industry in South Africa stands to benefit much from the implementation of the self-directed work team concept. Its introduction implies flatter hierarchical structures, empowerment of the workforce and increased participation. Research indicates that half of the initiatives to implement self-directed work teams, however, fail, and it is therefore imperative for companies to be aware of the factors impacting on the effectiveness of self-directed work teams in order to focus on these early in the implementation phase. The objective of the study was to qualitatively determine these factors. Semi-structured interviews based on the phenomenological method were carried out. The sample included members of, and individuals involved with, self-directed work teams (N= 26) from a large gold mining company in South Africa. Results show that most respondents rated the availability of resources to do their work as the most important factor affecting their effectiveness.

Jan 1, 2006

By S. R. Dindarloo

Although blasting is one of the most widely used methods for rock fragmentation, it has a major disadvantage in that it causes adjacent ground vibrations. Excessive ground vibrations can cause a wide range of problems, from nearby residents complaining to ecological damage. Prediction of blast-induced ground vibration is essential for evaluating and controlling the many adverse consequences of surface blasting. Since there are several effective variables with highly nonlinear interactions, no comprehensive model of blast-induced vibrations is available. In this study, the support vector machine (SMV) algorithm was employed for prediction of the peak particle velocity (PPV) induced by blasting at a surface mine. Twelve input variables in three categories of rock mass, blast pattern, and explosives were used for prediction of the PPV at different distances from the blast face. The results of 100 experiments were used for model-building, and 20 for testing. A high coefficient of determination with low mean absolute percentage error (MAPE) was achieved, which demonstrates the suitability of the algorithm in this case. The very high accuracy of prediction and fast computation are the two major advantages of the method. Although the case study was for a large surface mining operation, the methodology is applicable to all other surface blasting projects that involve a similar procedure.

Jan 1, 2015

By P. Forbes

Mining and metallurgical processing companies that have adopted the principles of good environmental management often find it difficult to carry out an environmental assessment that yields meaningful opportunities for improved performance. This topic was investigated by means of a case study of a South African Base Metal Refinery (BMR) producing primarily nickel. A process-based Life Cycle Assessment (LCA) was carried out on the refining process, with the environmental impacts related to the production of reagents and utilities forming part of the assessment. The lifecycle inventory (LCI) was based on plant operating data spanning 31 months of production, from which a baseline environmental profile could be generated and interpreted to indicate the main sources of potential environmental impacts. Consequently, opportunities for improved environmental performance could be identified from the LCA model, which expressly related potential environ-mental liability to specific sub-processes in the assessed industrial operation. The on-site steam plant was found to be the primary source of potential environmental impacts in most of the impact categories considered. In closing, the paper discusses some of the limitations encountered in use of the LCA method. Keywords: life cycle assessment; LCA; life cycle inventory; LCI; base metal refinery; improved environmental performance; environ-mental management systems; nickel refining.

Jan 1, 2000

By A. Cichowicz

The objective of this work is to quantify the effect of the rock mass surrounding a stope or a tunnel on the seismic signal so that the rockburst damage on the excavation can be derived. It has been shown that the transfer function of rock mass surrounding an excavation can be modelled using a damped oscillator. The method of estimating the transfer function is extended in this paper. The parameters of a damped oscillator are estimated using inversion techniques and the transfer function is modelled as a time-varying system. The technique is tested on data acquired at three different sites in two deep gold mines. Employment of a modal model of the transfer function was suitable in two cases. Application of this technique is essential to track the time variation of the natural frequency during ground motion caused by a seismic event.

Jan 1, 1999

By R. G. Tarr

During an intense and accurate study of initiation systems used on an AngloGold mine, Mine A, poor drilling practices were revealed. Graphic results of all actual measurements taken are shown below. [ ] Accurate drilling of shot holes will determine whether a mining operation is payable or not and at what pay limit mining can take place. Losing 30 cm of a potential 120 cm-hole length will result in a number of consequences, i.e.: ?Higher stoping costs ?Drilling of one shot hole twice in every five shifts ?Increased explosive cost as a result ?Excess stress on hangingwall and footwall due to bad face shape ?Excessive blast damage before the area is worked out. No wonder we have such a high-risk operation. Drilling accuracy is crucial to the profitability on any mine as profits are directly related to the quality and utilization of the drilled shot holes.

Jan 1, 2000

By B. Andresen, S. T. Johansen, H. Tveit, S. Grådahl, B. Ravary

The Norwegian ferroalloy industry has high ambitions regarding environmental standards. Basic research work has been performed to improve the fundamental understanding of ferroalloy processes and the environ-mental aspects. This paper will present work dealing with the understanding of formation and control of NOx, PAH and dioxins. During this work various techniques and methods have been applied, such as comprehensive industrial measurements, laboratory experiments, model development and application of Computational Fluid Dynamics (CFD). The main goal has been to reduce the environmental impact of ferroalloy plants, by means of improving the combustion processes done by introducing new charging routines and optimized furnace operations, instead of installing expensive gas treatment systems. The Norwegian obligations in accordance with the Gothenburg protocol are to reduce the NOx emissions by 30%, compared with the 1990 level within 2010. Measures developed in this work have resulted in 40-60%reduction in NOx emission, and major reductions in PAH and dioxins for ferrosilicon and silicon metal plants. This has been achieved by introducing semi continuous charging and improved furnace operations. Semi continuous charging and optimized furnace operations are shown to reduce the blowing activity (i.e. emission of large quantity of SiO over the charge by direct channelling from the crater zone). It also reduces variation in off-gas temperature and dust production. To understand the processes and to achieve our results we have used online equipment, with fast sample rates and response times, to measure the off-gas compositions and temperatures. Most of the measuring techniques used are based upon optical principles making use of the absorption- and emission spectrum of the gases. In addition a new prototype instrument is developed for continuous measurement of off-gas characteristics, total dust amount and off-gas temperature. The presented work is a result of a long term co-operation research and development teamwork, between the industry and the research community, and has improved both the process and reduced the emissions. The work has introduced new process design and operation standards, and has resulted in ferroalloy production with better environmental standards.

Jan 1, 2007

By R. J. Durrheim, Y. Yabe, M. S. D. Manzi, DSeis team, N. Z. Nkosi, S. B. Mngadi, Jr. H. Ogasawara

On 5 August 2014, the Orkney M5.5 earthquake, the largest in South African gold mining districts, occurred with an unusual strike-slip mechanism at great depth of 4.78 km below the surface. In a rare case, the ML 5.5 earthquake occurred within the area covered by the legacy 2D and 3D reflection seismic data acquired in the 1990s and 2000s for gold exploration and mine development. In addition, the earthquake ML 5.5 rupture plane was recorded and accurately delineated by the underground in-mine seismic network near the source region. The integration of the legacy 2D reflection seismic data and mine seismicity data allowed us to identify a near-vertical structure, striking northnorthwest-south southeast (NNW-SSE). The ICDP-DSeis team drilled three holes (Hole A, Hole B, and Hole C), and two holes (Hole B and Hole C), intersected the upper edges of the ML 5.5 rupture. These holes recovered metasediments, metabasalts, intrusive rocks including dolerite sills and lamprophyre dykes adjacent to the fault zone, and the fault gouge. Late Prof. Tullis Onstott and geomicrobiologists installed a packer in Hole A and successfully recovered saline water and detected gas (~10 MPa). Slip weakening and rupture propagation are significantly influenced by the existence of fault gouges and the production of wear material between two sliding rock surfaces. Using the fault gouge material recovered from Hole C, we conducted friction experiments under dry and room temperature conditions at high slip velocity of ~100 mm/s and normal stress of 2 MPa. The resulting steady-state frictional strength was ~0.66 over a slip weakening distance of ~9.1 m. The steady-state frictional strength was high, which may be caused by large gouge thickness, and the rate of wear generation. As a result, it is proposed that the Moab Khotsong ML 5.5 seismogenic zone is complex and could be controlled by three main processes: a) the complex structural architecture of the seismogenic zone (e.g., intersection of fault, lamprophyre dykes, and dolerite sills); b) the mechanical process induced by tectonic and/or mining related stresses; and c) the mechanical and chemical processes caused by the water and rock interaction.

Jan 12, 2025

By C. Musingwini

In the past ten to fifteen years, many organizations have applied business process re-engineering (BPR) to significantly improve their business competitiveness or stave off closures. The mining industry in Southern Africa is no exception and documented examples can be drawn from South Africa. Although the concept is superficially simple, its application has been marked by a high failure rate of about 70 per cent because it has been generally misunderstood. Shabanie mine, a chrysotile asbestos fibre producer in Zimbabwe took cognisance of this fact by cautiously embarking on a modular BPR programme in October of 2002. A year was used as a complete cycle or module for re-evaluation of the programme. Shabanie mine adopted BPR as part of management efforts to remain competitive amid serious threats to operational viability. These threats included hyper-inflation driven rising production costs, a declining world asbestos market and a possibility that Russia could take over the shrinking world asbestos market by dumping low-priced asbestos fibre. The only competitive advantage that the mine had was the high quality of its long-fibre chrysotile asbestos. The major BPR thrust was therefore to redesign processes for improved productivity and ultimately achieve a lower cost per ton of final asbestos fibre product. In addition, corporate culture change and cost-saving were also factored into the programme. This paper discusses the implementation experience of the BPR programme at the mine. The main BPR beneficial highlights are improved productivity, sizeable cost-savings, positive corporate culture change and identification of secondary projects. One of the lessons learnt from this programme is that mining companies will have to deal with the HIV/AIDS pandemic if they are to sustain high levels of productivity into the future.

Jan 1, 2005

By E. V. Lilford

Equity investors and project sponsors have divergent views about expected or minimum returns that should be generated by a mineral project. Irrespective of their views, the fundamental estimation of the corporate cost of capital remains singularly determinable, with additive components of risk and uncertainty often incorporated in the final analysis. This paper discusses and details the fundamental, numerical determination of the corporate cost of capital.

Jan 1, 2006

By J. H. Zietsman

It has previously been observed that industrial high-titania slags display a compositional invariance, remaining close to stoichio-metric M3O5. The present study focuses on this invariance and the phenomena which may cause it. The invariance was studied using thermochemical calculations and a mechanism is proposed for the observed behaviour. The mechanism suggests that a combination of thermochemical equilibrium and transient slag solidification and melting results in the observed compositional invariance. The proposed mechanism provides new insights and prompts questions about other mechanisms in the smelting process.

Jan 1, 2004

By R. P. Goel, P. N. Chaudhary, R. K. Minj

The bulk of high carbon ferromanganese produced in India continue to have more than 0.35% phosphorus since they are produced by carbothermic reduction process. The low phosphorus manganese ores are depleting fast and ferromanganese manufacturers will have no option but to use medium and low grade ores having high phosphorus content resulting in high phosphorus in the product. A systematic study was taken up at NML to solve this problem. Initially, a thermodynamic analysis was carried out for which Ba-P-O ternary predominance diagrams were constructed at several temperatures to predict the most suitable conditions for selective removal of phosphorus from high carbon ferromanganese. These conditions required a usage of a flux having a high level of basicity, moderate oxygen potential as well as low melting temperature. The experimental results showed that it was possible to remove phosphorus from high carbon liquid ferromanganese from 0.56%to 0.18% using BaCO3 based fluxes at the rate of 16-wt% of the ferromanganese charged. However, the Mn loss varied in the range of 2-5%. The objective of the subsequent study carried out at the laboratory scale was to optimize the flux consumption as well as minimize the Mn loss with effective dephosphorization by using BaO based calcined pellets instead of BaCO3 based powders. It was felt that the handling of pellets under plant conditions would be easier and also eliminate the loss of flux as a dust, which occurs when powder is added. These pellets were forced towards the bottom of the melt for better efficiency. For this purpose, a plunging system was designed and fabricated in-house that helped in reducing the flux consumption to less than 5% and also improved the kinetics of the process. The desired results were achieved within 10 minutes of the addition of the flux. The know-how is ready for transfer to interested parties and authors are willing to conduct large scale trials with them.

Jan 1, 2007

It is estimated that the tailings dam of the Mouteh Gold Mine, in Iran, contains more than 770 kg of gold. Microscopic analysis reveals that sulphide minerals and active carbon are the main sources of the gold in the tailings residue. Flotation and cyanidation tests on the samples of tailings were conducted. Flotation concentrates, containing around 87.79% of the gold, which were associated with sulphide minerals, were recovered. By regrinding, roasting, and cyanidation of the flotation concentrate, the gold dissolution recovery was in the range of 87.8 to 98.4%. The carbon-in-column method was used to recover 98% of the gold from the solution. Keywords: gold ore, pyrite, flotation, roasting, cyanidation

Jan 1, 2009

Interest in the potential use of high-density, thickened tailings has recently increased significantly. Reasons for considering this new technology vary across projects, but commonly include the need to conserve water, perceived lower risk of catastrophic failure, potential easier closure, or even reduced overall costs. As with any new technology, there has been some tendency to overstate its potential benefits. This paper reflects on whether or not the potential benefits that have been attributed to paste and thickened tailings have been realized. Using a grading system, thirteen benefits that were ascribed to the new technology some years ago are evaluated. Data is taken from case studies, and it is suggested that the key proven benefits appear to be reduced operating costs in some cases, reduced wall-building costs, and reductions in water consumption. One key potential benefit that has not been universally achieved is a reduction in the footprint of the tailings facility. Reports in the literature highlight the sometimes confusing nature of trade-off studies. Unless full life-of-mine costs are considered, these studies can be misleading and incorrect. The need to establish a consistent basis for comparative studies is discussed.

Jan 1, 2012