Search Documents

By Stephen C. Tadolini, Thomas M. Barczak

An underground investigation was designed and implemented by the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of pre-driven longwall recovery rooms supported with pumpable concrete roof supports. The pumpable roof supports were instrumented with hydraulic pressure cells to measure support loading. Displacement of the support was also measured to assess the support reaction to ground movements. Movement up to 12.5 m (40 ft) into the roof was measured with sonic probes and multipoint extensometers. Borehole pressure cells were installed in the panel fender and outby pillars to evaluate load transfer. Shield loading was also assessed to determine the impact of the panel fender yielding on face loading. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 3.12 m (10 ft) from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 15-20 cm (6-8 inches) once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 10 m (32 ft) horizon with total deformation ranging from five to 10 cm (2 to 4 inches), indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in instabilities that can lead to catastrophic results. Understanding the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields is providing valuable information for the refinement of the NIOSH Ground Reaction Curve for standing and intrinsic roof support system design.

By Rolland L. Blake

Petrographic methods of examination were used by the Bureau of Mines on a suite of samples of ultramafic rock from Soapstone Ridge, Ga., located about 8 miles south-southeast of Atlanta. The samples were analyzed to determine (1) their potential for releasing regulatory particles upon crushing and grinding and (2) their concentration of fibrous particles that approach the dimensions of amphibole and serpentine asbestos minerals. Such particles might be generated during grading and excavation for housing and industrial development and could become a health concern. Light optical microscopy, scanning electron microscopy, and X-ray diffraction were the techniques used to examine the samples. Six of the twelve samples contained amphibole as a major mineral; in five, it was a moderate to minor mineral. One sample contained no amphiboles, and serpentine was not observed or identified by X-ray diffraction in any of the samples. In nine of the samples, the amphiboles exhibited a habit that was either prismatic or acicular, but not asbestiform. Two of the samples did contain asbestos, occurring as small veins or fracture fillings, which represented only a minor percentage of the total sample. Similar petrographic screening is recommended for examining any rock deposit or mine location to delineate hazardous and nonhazardous mineral areas.

Jan 1, 1982

By W. H. Young

THE DOMEST[C bituminous coal and lignite industry remained fairly steady in 1959 compared with 1958. Although mechanization continued to expand and production increased slightly, consumption, average value, exports, and employment decreased. The percentage of underground production mechanically loaded, the percentage of total production mined by stripping, and tonnage per man per day were at their highest levels. Production.-The output of bituminous coal and lignite in 1959-412 million tons-was 0.4 percent greater than the 410.4 million tons produced in 1958. Production was retarded in 1959, largely owing to the steel strike and reduced exports.

Jan 1, 1960

By Robert K. Koch

Laboratory-scale studies on defluorination of natural and synthetic fluorspars by pyrohydrolysis at 1,500° C. were made to determine the feasibility of developing a process for producing hydrogen fluoride from siliceous fluorspars. It was found that the reaction (at 1,500° C.) is not promising for process development, even though a silica-free offgas can be generated. The primary difficulty is the low hydrogen fluoride content of the offgases; an HF content of 6 percent was the best achieved. Previous research by the Bureau of Mines has demonstrated that offgases averaging 27 percent hydrogen fluoride can be produced under carefully controlled conditions at 1,280° C. The lower temperature process is a better method for production of HF. However, charges in which the CaF to Si02 mole ratio varied from 0.4 to 2 could be processed with similar results. Also, combined alumina and ferric oxide contents up to 25 mole-percent did not noticeably alter the rate of defluorination. Therefore, virtually any natural siliceous fluorspar would respond in essentially the same manner when exposed to water vapor at 1,500° C.

Jan 1, 1962

By M. M. Tilman

The Federal Bureau of Mines developed a rolling method that improves creep resistance and yield strengths of lead alloys containing up to 5 wt-pct Sb. The 0.69-inch-thick slab-cast alloys were breakdown-rolled to 0.226 inch and finish-rolled to 0.063 inch at 5-or 20-pct reduction per pass. Rolling was at room temperature to simulate conventional cold rolling, and at 75°, 125°, and 175° C. Two alternative methods evaluated consisted of (1) a single cold final pass followed by annealing and (2) a single hot final pass. Two additional processing methods involving percipitation strengthening were included for comparison. Compared with conventional cold rolling, hot rolling at 125° and 175° C with multiple light passes vastly improves creep resistance and raises yield strengths. Tensile strengths are less affected. The other treatments also improve creep resistance significantly and generally improve tensile properties; magnitudes vary with treatment and composition.

Jan 1, 1975

By W. P. Yant

The widespread use of toluene in industry and the importance of air analysis in industrial-hygiene surveys have created a need for a simple and accurate method for determining toluene vapor in air. Most of the methods used to determine small quantities of toluene in liquid or vapor form are based on the measurement of its physical properties. Methods based on fractional distillation, determination of specific gravity, use of the interferometer, use of the spectrograph, and sorption on solid sorbents with subsequent determination of gain in weight have been employed. Distillation and specific-gravity methods are not applicable to the small quantities of toluene found in the air, and use of the interferometer, spectrograph, and sorption methods either are not specific for toluene in the presence of other volatile substances or require expensive equipment.

Jan 1, 1936

By W. W. Adams

"The National Safety Competition of 1930, the seventh annual contest conducted by the United States Bureau of Mines to promote safety in the mines and quarries of the United States, has been concluded, and the five winners of the bronze trophies, The Sentinels of Safety,' which are provided by the Explosives Engineer magazine and awarded annually for the most excellent safety records, have been determined by the committee of award. One trophy was awarded to an anthracite mine in Pennsylvania, one to a bituminous coal mine in the same State, one to an iron-ore mine in Michigan one to a gypsum mine in Ohio, and one to an iron-ore opencut mine in Michigan.These trophies were awarded to the companies for having the smallest loss of time from accidents in proportion to the total number of man-hours worked by all employees at their mine or quarry. Honorable mention was awarded to each mine or quarry that ranked second, third, fourth, or fifth in its own ground and to all plants that were operated without a lost-time accident during the contest year. Eighty-four out of 337 plants that competed for the trophies were operated without an accident that disabled an employee beyond the day on which the accident occurred.Under the contest rules, all mines and quarries were divided into five groups, four of the groups representing different classes of underground mining operations (anthracite, bituminous coal, metallic ore, and nonmetallic mineral), and the fifth group repre-senting the quarrying or opencut mining of minerals whether metallic or nonmetallic. Twenty-seven mines were included in the anthracite group, 68 in the bituminous group, 52 in the metal group, 24 in the nonmetallic-mine group, and 166 in the quarry and opencut-mine group. The total of 337 mines and quarries was 26 more than the number of plants that completed the contest during the previous year.The committee of award which determined the winners of the contest was composed of seven members, all known throughout the mineral industry but not connected with the United States Bureau of Mines. The committee included W. H. Cameron, managing director of the National Safety Council; William Green, president of the American Federation of Labor; James F. Callbreath, Secretary of the American Mining Congress; T. T. Read, Vinton professor of mining of Columbia University and editor of Mining and Metallurgy; C. B. Huntress, executive secretary of the National Coal Association; A. J. Curtis, assistant to the general manager of the Portland Cement Association; A. T. Goldbeck, director of the bureau of engineering of the National Crushed Stone Association."

Jun 1, 1931

By W. P. Yant

The widespread use of toluene in industry and the importance of air analysis in industrial-hygiene surveys have created a need for a simple and accurate method for determining toluene vapor in air. Most of the methods used to determine small quantities of toluene in liquid or vapor form are based on the measurement of its physical properties. Methods based on fractional distillation, determination of specific gravity, use of the interferometer, use of the spectrograph, and sorption on solid sorbents with subsequent determination of gain in weight have been employed. Distillation and specific-gravity methods are not applicable to the small quantities of toluene found in the air, and use of the interferometer, spectrograph, and sorption methods either are not specific for toluene in the presence of other volatile substances or require expensive equipment.

Jan 1, 1936

By John Millhiser, Margaret Bonarek, Dennis McLaughlin

This report contains a description of the contract activities performed by ENSCO, Inc. under contract No. H0178069. The purpose of this project was to enhance the Bureau of Mine's Cableless Electronic Survey System use to aid in the drilling of long (approx. 2000 feet) boreholes in coal. This drilling is performed as part of the methane drainage program. The system that was ultimately developed was field tested and demonstrated in actual in-mine drilling activities. The significance of this system as compared to previous drill survey systems is the fact that it surveys without having to be inserted and removed for each survey point. It is so designed that it can withstand the shock and vibration experience by the drill string during drilling. This means an increased productivity is now possible in that drill operators can determine drill bit positioning in a near real-time environment.

By W. P. Diamond, John C. LaScola, D. M. Hyman

In 1972, the Bureau of Mines developed a direct-method test for measuring the gas content of virgin coal core samples for coal mine health and safety considerations. Since that time, approximately 1,500 coal samples from more than 250 coalbeds in 17 States have been collected for gas content determination. The gas content data, when combined with geologic and engineering studies, can be used as a basis for a preliminary estimate of mine ventilation requirements, and to determine if methane drainage in advance of mining should be considered. The data are also critical in delineating coalbed methane resources and in utilization feasibility studies. This report makes the Bureau's extensive data base of gas content data more readily available to the coal and gas industries. The data are presented in tabular form, alphabetically by coalbed name and by State. The components of the total gas content (lost, desorbed, and residual gas) are given, Location (State and county), sample depth, coalbed or formation name, and coal rank are included for geographic and geologic identification.

Jan 1, 1986

By Jacqueline A. McClaskey

The U.S. Bureau of Mines (USBM) Information and Analysis Directorate collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The USBM's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the USBM survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By Robert E. Hershey

1. The investigation shows that the Sewanee coal bed is the most important bed in Grundy County arid is the only bed that has had any sustained production. There is no production, at the present time, from any of the other coal beds in the county. The Richland (Lower Sewanee or Coke Oven) coal bed has been prospected but has never been developed extensively. The Angel coal bed has been worked to a very small extent near Beersheba Springs, Tenn., for local consumption. The Battle Creek coal bed has been worked sporadically near Monteagle, Tenn. 2. Known measured and indicated reserves in the Sewaneee coal bed, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 15 millon short tons as of January 1, 1953. Of this total, 10 million tons represents coal 28 inches and more thick. Areas in the bed were omitted from the estimate where available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By S. H. Ash

"INTRODUCTION Mine fires have occurred since underground mining of minerals began, and they are still occurring. The technical literature is replete with papers relating to mine fires.Means and methods for controlling and extinguishing mine fires and preventing explosions and other accidents require the collection and analyses of samples of the atmospheres surrounding the fire. Such atmos¬pheres are complex mixtures of gases (1, 3, 4, 15, 21, 23).3/SUMMARYExperiences at mine fires (1, 3, 4, 15, 21, 23) have proved conclusively that mine-air analyses furnish the only means of judging what is going on in a mine fire area. Mine-air analyses give evidence of conditions that require immediate protection, govern the order and control the manner in which a fire is fought, show the necessity of bulkheads and establish the places to construct them, indicate whether or not a fire is being controlled or is being extinguished, and govern procedure in sealing and unsealing mine fires.It is commonly believed that danger to life and property from mine-fire atmospheres is greatest in coal mines; this is true only to the degree that the explosion hazard is greater in coal mines than in noncoal mines because of the presence of combustible gases. The problem of gas poisoning is greater in noncoal mines because of the more frequent occurrence of poisonous and innocuous gases, oftentimes the lack of controlled ventilation, and usually greater difficulties in sealing mine-fire areas. Sulfide minerals present a serious hazard in many metal-mine fires when sulfur dioxide is formed. The country rock or ore body itself may contain or be limestone, which may be calcined. Emanations of carbon dioxide are found."

Dec 1, 1950

By M. K. Larson, J. P. Dunford, E. G. Zahl, T. M. Brady

Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, Spokane, WA, have collaborated with three Western longwall coal mines in an on going effort to develop technologies that will aid in providing safe and stable working areas. The goal of the research described here is to develop a stress monitoring system that will provide immediate information to mine managers for making daily safety decisions as areas of poor ground are mined through. Initial work has focused on answering preliminary questions regarding the reliability and use of stress change patterns. Research is concentrated on monitoring horizontal stress because horizontal stress is transmitted over long distances through stiff strata, thus allowing an extended length of entry to be monitored. This paper presents an explanation of the concept, key results from field tests at two mine sites, and a proposed process for implementing a monitoring system. System design layouts, instrument use, data collection and interpretation methods, and processes to present findings to mine staff are described. Additional validation and correlation with actual failure mechanisms are required before this approach can be recommended at ongoing operations. However, initial results indicate that this approach shows promise in mines prone to bumps and roof falls associated with large stress changes. In particular, analyses of measured changes in horizontal stresses appear useful.

By D. R. Dolinar, J. Pablic, D. C. Oyler, T. P. Mucho

At a mine in central PA, high horizontal stresses have caused long running roof falls resulting in hazardous conditions for the miners and the premature abandonment of panels. Because of these conditions, the mine requested assistance of the National Institute for Occupational Safety and Health (NIOSH) in utilizing the 'advance and relieve method to mitigate the affects of horizontal stress on the mine roof. "Advance and relieve" mining involves the removal of a pillar or a portion of a pillar during development, thereby creating a cave along one side of the panel. Following cave development, the horizontal stress is relieved over the workings adjacent to the cave in the active panel. The mine has used this system in three panels with a significant reduction in stress damage and no large roof falls.

By M. Hertzberg

This Bureau of Mines report describes experimental and theoretical studies of diffusion flames in free convection. The cross-coupling between buoyancy-induced flows and the combustion process is explored as it relates to the size, structure, and radiative balance of flames. New data are presented for the size-dependent radiance oscillations of diffusion flames and for the angular distribution of the total radiant intensity from a small methanol pool flame. Both amplitude and frequency of the measured oscillations are compared with theoretical predictions that are based on a new view of the structure of diffusion flames. This new view, which is at variance with the traditional one, assumes uniform reaction in the diffusive mixing zone, and recognizes the significance of the role played by convective buoyancy and its duality in both aiding and impeding flame propagation. Buoyancy quenches propagation at low burning velocities, introducing a real discontinuity in the combustion rate. A "flammable volume" is thus defined as that bound between lean- and rich-limit contours. However, in the flow disturbances generated by combustion waves that consume that volume, buoyancy aids propagation by promoting the convective mixing of a new flammable volume. The measured radiance oscillations are manifestations of these propagation and remixing cycles.

Jan 1, 1978

By Eric B. Sansone

The Federal Coal Mine Health and Safety Act of 1969 requires coal mine operators to sample accurately the amount of respirable dust in the mine atmosphere. A technique approved for such sampling employs a 10 mm nylon cyclone followed by a membrane filter (nominal pore size ????= 5 µm) and a pump. The pump is required to provide a flow rate of 2.0 ± 0.1 liters per minute. Calibrations have yielded a range of flow rates (1.4 to 2.8 1pm) at which the cyclone should be operated to remove the non-respirable portion of the dust. The purpose of this project was to evaluate the performance of the 10 mm nylon cyclone at flow rates of 1.8 and 2.0 1pm using a polydisperse coal dust aerosol. The penetration characteristics of the cyclone were to be compared to the United States Atomic Energy Commission's respirable dust standard. The effect of relative humidity on cyclone penetration characteristics was also to be observed.

Jan 1, 1973

By Ruth A. Holmes

A Bureau of Mines method for recovering nickel, cobalt, and copper from low-grade domestic laterites is described, which includes the unit operations of solvent extraction and electrowinning. Previous Bureau work indicated that addition of Na2S04 (sodium sulfate) to the nickel electrolyte improved current efficiency in nickel electrowinning. The present study determines the compatibility of Na2S04 with nickel strip-ping in the solvent extraction operation of the Bureau method. The effect of adding 100 g/l Na2S04 on nickel stripping, phase disengagement, and pH was determined in comparative laboratory-scale tests. In continuous-circuit testing, Na2S04 reduced stripping efficiency to the extent that five, instead of four, strip stages were required for complete stripping of nickel from the loaded solvent. In tests made in a phase-disengagement cell that had a variable settler area, the addition of Na2S04 did not significantly affect phase separation characteristics. The pH of the nickel electrolyte in the temperature range of 20° to 65° C was also unaffected by the addition of Na2S04. An economic evaluation showed that the energy saved by adding Na2S04 to the electrolyte would more than offset the cost of adding another stripping stage.

Jan 1, 1983

By James H. Scott

A technique of seismic refraction data analysis has been developed in which a digital computer is used to generate a two-dimensional model representing a layered-earth depth interpretation. Travel times are picked on seismic records by the human interpreter. These times, together with shot point and geophone locations and refraction layer control information, are submitted to the computer on punched cards. A first approximation delineation of each refraction horizon is obtained by a computer adaptation of the delay-time method. The approximation is then tested and improved by the computer through the use of a ray-tracing procedure in which ray travel times computed for the model are compared against field-measured travel times. The model is subsequently adjusted in an iterative manner so as to minimize the discrepancy between computed and measured travel times. The Fortran program is listed in the appendix of the report together with instructions for preparing data cards and examples of results.

Jan 1, 1972

By B. M. Bench

This Bureau of Mines report describes photo lineaments obtained from stereoscopic examination of vertical aerial photographs and by the Ronchi grating study of aerial photoindex sheets. The photolineaments are compared with the trends of oriented fracture systems procured by measuring the compass direction of joints in bedrock. The relative reliability of the methods is shown, and the results are presented in graphical, tabular, and written form. Analyses of field measurements of strikes of bedrock joints in the project area indicate for the most part two intersecting sets of major joints oriented N 76° W -N 15° E, and N 57° W -N 27° E. The analyses of lineaments determined by stereoscopic examination of aerial photographs show dominant trends of lineament zones of weakness to be an average of N 65° W -N 20° E. Analysis of lineaments found by Ronchi grid viewing of aerial photoindex sheets indicate dominant trends of N 70° W -N 27° E. The three methods give similar findings and verify the work of previous authors. The Ronchi grid method is a useful guide, but it cannot be substituted for the two more painstaking methods.

Jan 1, 1977