Search Documents

By Constantine C. Popoff

The Hermada antimony deposit is in the Sewtooth Range in southwestern Idaho, about 77 miles by road northeast of Boise. Stibnite mineralization occurs over an area one mile wide from west to east and two miles long. It is locally referred to as the Swanholm district. In 1947 high- grade stibnite ore was discovered on the East Fork of Swanholm Creek. Since then, ore in commercial quantity has been produced by the Hermada Mining Co. The total output for 1947-50 was about 5,000 tons of ore, containing 640 short tons of antimony metal.

Jan 1, 1953

By H. C. Verakis, M. L. Harris, M. J. Sapko, K. L. Cashdollar

In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. The National Institute for Occupational Safety and Health (NIOSH) has developed a hand-held instrument that uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture. This instrument is called the Coal Dust Explosibility Meter (CDEM). In this study, NIOSH personnel accompanied Mine Safety and Health Administration (MSHA) inspectors on their routine band surveys in five and three underground coal mines in MSHA District 2 (PA) and District 11 (AL), respectively. While underground, NIOSH personnel and MSHA inspectors used the CDEM to assess the explosibilities of the dust samples. The values of percent incombustible content (% IC) determined by the CDEM agreed well with those obtained later by low temperature ashing (LTA) in both MSHA and NIOSH laboratories. Further, the meter identified some samples as potentially explosible that LTA analysis had found to possess sufficient rock dust for inerting. The CDEM provides more information on the hazards in the mine. Rapid identification of areas with explosible dust mixtures using the CDEM allows for immediate intervention rather than a wait of several weeks for laboratory analysis.

By L. Crocker

The Bureau of Mines investigated processes for recovering a marketable lithium product from the montmorillonite-type clays of the McDermitt caldera. The clay deposit, located on the Nevada-Oregon border, is estimated to contain over 3 million short tons of lithium. Limestone-gypsum roasting and selective chlorination proved most successful for extracting lithium from the clays; 80-pct Li recovery was achieved using either technique. With both processes, lithium silicate in the clay was converted to a water-soluble compound-either lithium sulfate or lithium chloride. The lithium was then recovered as a carbonate by water leaching the calcine, concentrating the leach solution by evaporation, and precipitating the lithium with soda ash. The operating costs for the limestone-gypsum roast process were estimated at $2.02/lb Li2C03; selective chlorination operating costs were estimated at $3.85/1b Li2C03. The current selling price of Li2C03 is about $1.50/lb. A detailed flowsheet, material balance, and process evaluation are presented for the limestone-gypsum roast process. In addition, lithium reserves and resources are discussed and the McDermitt clays are described.

Jan 1, 1988

By Stephen Utter

Stresses induced by block-caving mining were estimated from in-place measurements of strain or deformation in rock and concrete around mine openings. The four types of gages used for measurements in the Climax Molybdenum mine during 1959-61 were Whittemore gage, Carlson strain meter,2 Valore strain cell, and Climax extensometer. Gage performance in the laboratory was evaluated by stressing instrumented rock and concrete specimens in a universal testing machine and by comparing measurements taken by the gages and a standard gage. Gage performance in the mine was evaluated by comparing measurements taken during an 18-month test. The Whittemore gage, Carlson strain meter, and the Climax extensometer proved suitable for the investigation; the Valore strain cell, effective in the laboratory tests, gave erratic measurements in the mine.

Jan 1, 1965

By Fred W. Snow

This paper describing the mining practices at the Magma mine, Superior, Ariz., is one of a series being prepared by the Bureau of Mines on mining prac¬tices, methods, and costs in the various mining districts in the United States. At present (1929) practically all the mineral production in the Superior district is from the Magma mine of the Magma Cooper Co. The ore is mined for its copper but contains associated silver and gold. Both direct smelting ore and ore of concentrating grade are produced. The mining methods now in use at the Magma mine were adopted or developed as knowledge was gained of the physical condition of the ore bodies and the inclosing formations; the wall rock is soft and crushed and the ore is relatively hard. In general, existing methods have been adapted to fit local conditions, but some of the mining practices used were originated at this mine. Most of the ore is mined by a combination of rill stopes and pillar stopes. The pillars are extracted by underhand mining.

Jan 1, 1929

By E. R. Spencer, D. R. Babich, L. A. Alcorn, A. K. Smith

Noise is one of the most pervasive health hazards in mining. A compilation of Mine Safety and Health Administration (MSHA) noise survey data for fiscal year 1990 shows that approximately 40% of the total samples taken for longwall occupations exceeded the Permissible Exposure Limit (PEL) of 100% (Gigliotti et al., 1991). To effectively determine worker noise exposures on longwall coal mining systems, it is necessary to provide accurate baseline measurements for these mining systems. This research was designed to develop measurement methods and test procedures for identifying noise sources that are major contributors to the underground noise exposure of longwall coal mining system workers. The measurement system that was used to analyze the noise sources around a stageloader used stationary dosimeters in a documented repeatable pattern to record the sound pressure and dose levels. A time-motion study of the cutting cycle and stageloader operator’s work cycle was done to correlate the sound levels at measurement locations and the resulting operator’s daily dose with significant noise events. Results from the underground measurements show that the highest sound levels recorded were at the stageloader discharge segment and tailpiece controls, where sound levels remained about the same throughout the test.

By Duvall Wilbur I.

This is the second report to be presented on th application of stress analysis to underground Mining problems. In part I2/ of this investigation the stress distribution around single openings in unidirectional and hydrostatic stress fields was analyzed. Relationships between maximum stress concentration and size and shape of openings were determined by the photoelastic method. In most cases the results were verified by mathematical methods This report considers the stress distribution in pillars formed by two or more openings in a. unidirectional stress field. Relationships between stress concentrations and size and shape of pillars are developed. Applied to mining, results snow how estimates may be made of the stress distribution in pillars, what factors cause high local stresses, and how local stress concentrations may be reduced by proper design of mine openings. The photoelastic method was used, as in Part I, to study the stress distributions, and, whenever possible, the results were verified mathematically. A description of the photoelastic method and equipment is .given in Part I.

Jan 1, 1948

By Frank B. Fulkerson

This is the second of two interrelated studies of waterborne transportation. The first study discussed transportation of mineral commodities on the inland waterways of the South-Central States.2 Together, the two surveys describe and analyze the flow of foreign and inland waterborne commerce of the gulf coast. All the principal mineral-industry imports and exports of the gulf coast are mentioned in the report, including metals, nonmetals, and mineral fuel products, The gulf coast foreign trade in mineral industry products was determined to be composed of a small number of commodities.

Jan 1, 1971

By Sara J. Davenport

The human race has been exposed to copper for thousands of years, as copper and gold were the metals first used by man (1). if According to Ramazzini (2), "of all the metals that man's ingenuity has contrived to dig out of the bowels of the earth, iron and copper are the most useful, far more so than silver and gold." Workings of copper in the oldest known copper mine associated with the smelting of this metal have been traced back to 4300 B. C. Facts revealed by archeological research in India, Austria, Hungary, France, Italy, and Spain indicate that the use of copper probably began about 5000 B.C. (3), and that about 4000 B.C. a copper age came intermediate between the stone and bronze ages (4). Copper ores are rather widely distributed and are found in nearly every country. Many of the copper minas of Europe have been worked since before the Roman Empire. The must important mines in Europe occur in the district around Huelva, extending into Spain and Portugal. The German deposits are located mainly about Mansfeld (Rhenish Prussia); they have been worked continuously for 1,000 years. Some of the mines in Africa have been worked by the natives for centuries, and China has produced copper from shallow pits for thousands of years. India also has many ancient mines worked in the early centuries (2).

Jan 1, 1953

By C. S. Compton, D. R. Dolinar, D. C. Oyler

More than 80% of U.S. roof bolts are fully-grouted, but about 1500 roof falls are reported each year. Anchorage failure of a fully grouted bolt can occur when the roof is active near the top of the hole. This paper reports on an extensive series of short-encapsulation pull tests (in which the bolts are installed with only 1 ft of resin) that were conducted in the National Institute for Occupational Safety and Health (NIOSH) Mine Safety Research Laboratory and operating mines in WV and PA. The tests confirmed that poor anchorage can been countered under some weak rock conditions. Suggestions for improving anchorage are included.

By Kenneth L. Cook

From March 1944 to July 1945 the Division of Geophysical Exploration of the Federal Bureau of Mines made magnetometer surveys of some of the principal iron ore deposits of the Iron Springs district, Iron County, Utah. The district comprises a belt about 23 miles long and 3 miles wide. Most of the large ore bodies are found as pods of replacement ore within a favorable limestone bed lying at the margins of three separate igneous intrusions in the district The magnetic surveys were confined chiefly to this geologically favorable zone at the margins. The iron ore is a mixture of magnetite and hematite. The magnetite content of the ore ranges from 14 to 58 percent. Magnetic anomalies of 1,250 gammas or more were usually found over the near-surface ore bodies. About 62,000 magnetometer stations were taken over a total traverse distance of about 300 miles. Outcropping ore bodies were surveyed to determine, insofar as was possible from the magnetic data, their probable length, width, depth, extent, strike, dip, and tonnage. Geologically favorable areas where no ore is exposed were explored in an endeavor to find new ore bodies. Favorable locations were determined for exploratory diamond drilling, both in areas of exposed ore bodies and in areas of newly discovered magnetic anomalies. Forty-five separate magnetic anomalies that indicate the possible existence of ore bodies were observed. Of these, 13 anomalies are caused by outcropping ore bodies of proved commercial size. Five are caused by non-outcropping ore bodies of proved commercial size which were discovered, in whole or in part, as a result of the geophysical surveys. Of the remaining anomalies, which lie in virtually un-tested areas where few or no ore bodies are exposed, six probably are caused by large, unexposed replacement ore bodies, nine are possibly caused by large, unexposed replacement ore bodies, and six are probably caused by unexposed magnetite veins of some small commercial importance,

Jan 1, 1949

By John Wilson

This report describes the performance of Phase I of a project to design, analyze, and demonstrate a multilift longwall mining method applicable to mining coal seams twelve (12) feet or more in thickness. A non-simultaneous multilift operation is the most viable thick seam mining technique for introduction to the United States coal industry. In the case of the proposed site at Emery, Utah it will result in an increase in coal extraction from 30% with present methods to at least 50% and possibly more. The major technological advance involved in this project is mining a lower lift under a previously mined upper lift. To accomplish this, entries must be developed and maintained beneath the upper lift gob. This will necessitate the use of steel supports at frequent intervals throughout the lower lift' entry system. This has not been done in the U.S. to date. An economic analysis of the project indicates that, while this method will result in a higher than average cost per ton for coal mined, the coal would be competitive with current-operation in the area.

Jan 1, 1976

By E. Don Dilling, Wm. F. Hergert, J. W. Pennington, C. E. Wood, M. J. Slendlove, H. A. Doerner

"INTRODUCTION The Bureau of Mines began a study of various methods for producing magnesium metal from magnesite ores in 1936 at Pullman, Wash., with the cooperation of Washington State College. This work included a study of the basic principles involved in the reduction of magnesium oxide by carbon, which soon led to the development of a continuous process. In May 1939, a small pilot plant was operated, which included a small single-phase arc furnace with a hydraulic feed mechanism and an oil-spray device for shock cooling the metal vapor. 5/Subsequently, the Ford Motor. Co., Dearborn, Michigan, began a study of this process on a larger scale. A pilot plant with a nominal capacity of 10 pounds of magnesium metal per hour was constructed and operated intermittently. A larger unit with a nominal capacity of 100 pounds of magnesium per hour was partly constructed when war activities prevented experimental work.In the meantime, the process was greatly improved through continued investigation by the Bureau of Mines at Pullman, and these improvements were successfully tested by continuous operation in a small pilot plant having a normal capacity of 4 pounds an hour."

Aug 1, 1945

By Galen G. Waddell

Dilation and contraction of the rock surrounding horizontal access open-ings of a deep mine were analyzed during stope advance to determine what type of measurements, made with relatively inexpensive instrumentation, would best reflect the rock behavior. A variety of instruments, mostly mechanical extensometers, were used. Detailed descriptions are given of Down-the-hole extensometers, floating rockbolt clusters, transit surveys, and other instruments and measuring techniques. Although all of the radial-deformation-rate graphs illustrated useful rock behavior data, the most informative graphs were compiled from data procured with the radial extensometers that penetrated, to various depths, the rock around the access openings. An analysis is given of measurement data on the rock around lateral drifts and across and adjacent to the nearly vertical vein of the Star mine, Burke, Idaho. Several useful relationships were found between the rock deformation rate and the stoping process. Information was produced on the elastic state of rock around an underground opening, effectiveness of stope support, rheology of rock, zone of influence around stopes, effectiveness of rockbolts, axis of maximum strain in a plane perpendicular to the long axis of the lateral, and other phenomena. This information could be of particular value in determining location, design, and support of underground openings.

Jan 1, 1966

By F. V. Meriwether

The Bureau of Mines, in cooperation with the Federal, State, and local health services, and the mining companies, and miners? organizations, has for several years been carrying on sanitary surveys of mining districts in various states, with the purpose of collecting information on good and poor practices in mine sanitation, construction of approved wash-houses and change houses, the measures being taken to combat preventable diseases, the essential features of good houses for mining towns, and other conditions affecting the health and efficiency of miners and their families. The knowledge thus gained is disseminated for the common benefit of the mining industry. The sanitary conditions in the coal-mining districts of Alabama, as found by a recent survey made by the writer, are presented in this report. In addition to the towns on which this report is chiefly based, at least twice as many were visited where no details :were taken, but their general conditions are taken into consideration in summing conditions in the coal districts.

Jan 1, 1926

By C. W. Owings

"PURPOSE OF REPORTMany bituminous coal-mine officials realize that coal dust presents an ever-present coal-mine explosion hazard, and that persons forced to breathe large quantities of it may be more subject to respiratory infection than persons working in less dusty atmospheres. As an outgrowth of the realization that coal dust should be allayed at its source, many mining companies have expressed the desire to install dust-allaying equipment, and in a number of mines, water or wetting solution is being applied on the cutter bars of mining machines, on mobile loaders, belts or conveyors underground, and tops of mine cars. Spraying equipment also has been installed on dumps to allay dust during dumping operations. Dust-allaying equipment has not been standardized, however, because manufacturers have found that many prospective purchasers of such equipment have different ideas. These manufacturers wish to standardize, so far as feasible, the types and placement of such equipment. Many mine officials, although interested, do not know the best or most effective methods for allaying dust.For a number of years the Bureau of Mines has advocated allaying dust by applying water or, more recently, water modified by a wetting agent on the cutter bar of mining machines and by applying water to loaded and empty mine cars in order to keep as much dust as possible from spilling onto the haulage roads. In recent years this Bureau has also advocated applying water with or without a wetting agent during mechanical loading of coal and during unloading of coal from trackless cars or buggies and from elevating conveyors. It has now become apparent that specific arrangement of pipes, hose, and nozzles should be standardized to at least some extent. It is the purpose of this report, therefore, to give in detail suggested arrangement of dust-allaying equipment in the hope that both manufacturers and mine officials will have available dust-allaying equipment with maximum efficiency to do the desired work."

Nov 1, 1945

Since mid-July, most domestic producers have been marketing 99.5 percent unalloyed aluminum ingot at 53-57 cents per pound. Dealers in the United States have recently quoted ingot at 52.3-52.8 cents. On October 2, London Metal Exchange will trade aluminum, selling contracts on a cash and a 3-month basis. New York dealers were quoting August ingot at 52.3 52.8 cents. The Bonneville Power Administration announced that, effective December 20. 1978, electric power rates charged primary aluminum producers in the Pacific Northwest would be increased The increase (equivalent to about 4 cents per pound of aluminum produced) will raise the average rate to about 8.7 mills per kw-hr compared to 3.2 mills per kw-hr.

Jan 1, 1978

By W. C. Sanborn

The Bureau of Mines program of investigation and development of domestic mineral deposits had as its wartime objective the most effective immediate utilization of these resources in the interest of National security. Since the war, the results of individual projects are being prepared for publication as rapidly as practicable. Numerous chromite deposits were examined, among them those of the French Hill Mine in northern California. Situated 16 miles east of Crescent City, 76 miles from the nearest railroad shipping point at Grants Pass, Oreg., this deposit had a recorded yield of about l4,000 tons of metallurgical-grade chromite to the end of 1943. By the end of 1946, total production was more than 25,000 tons, averaging 43 percent Cr2O3, with a chrome:iron ratio of about 2.5:1.

Jan 1, 1948

By J. R. Thoenen

In June 1929 the Bureau of Mines issued a 13-page Information Circular entitled "Mineral wool." This was one of the first publications to present to the public some technical aspects of the mineral-wool industry. Since that time several articles have appeared on the subject in the technical press as well as publications by State organizations. Inquiries for information on mineral wool have continued to be received by the Bureau of Mines in large numbers, and in 1935 it was decided, with the cooperation of the is industry, to make a field survey of the plants then producing and to collect therefrom technical data to be compiled in a paper for public distribution. As a first step, a brief questionnaire was mailed to the known producers asking if they would cooperate for publication. Favorable replies were received from of percent of the manufacturers, and the field work was started. As the study progressed and tie number of plants visited grew, it became more and more apparent that the industry had made rapid strides in technical operation and control of their product, as well as in increasing production during the mast decade.

Jan 1, 1938

By Theron A. Klinefelter, Sidney Speil, Sidney Gottlied

"INTRODUCTION The investigation of domestic talcs by the United States Department of the Interior Bureau of Mines, was initiated in December 1941 at the request Gen. Charles Hines of the United States Army. The urgency for such study was expressed by General Hines as follows:The radio-manufacturing industry has recently been expanded by the Army to provide sufficient, capacity for defense needs, and considerable concern has been expressed by the supply Arms and Services over maintaining continued availability of supplies of the necessary raw material. These ceramic products are used by the Signal Cores in all Army radio equipment, and to a greater degree in the new special ultra-high-frequency equipment. The Air Corps has recently become a user large amounts of radio-grade ceramics for aircraft spark-plug covers required for high-altitude operations. In addition, the use of this material is essential to the proper functioning of the radio-navigation aids of the Civil Aeronautics Board.Progress in the Bureau of Mines studies on talc was made available to representatives of the Army and Navy through frequent interim reports. Through the efforts of the several war agencies concerned with raw-materials supply and the domestic talc producers, the condition of scarcity that developed in 1942 passed to one of ease in 1943, and has so continued to date. Tentative estimate of reserves delineated indicates a supply of high-grade steatite sufficient to meet military war requirements for at least 4 or 5 years."

Apr 1, 1945