Search Documents

By D Schneider, H Elliott

The advantages and disadvantages of using inclined boreholes in blasting has been under discussion for a long time. Some recognized disadvantages are that drilling costs, both operating and capital costs, are higher for inclined holes than for vertical ones, and that drilling accuracy is more difficult to maintain. People who have used angled holes in practice, on the other hand, have claimed that the quality of blast results was improved. In fact, their popularity has increased, especially in Australia.

Jan 1, 1988

By Seokbin Lim

According to published literature, the equation of motion of linear shaped charges (LSCs) has been investigated as early as the 1960s in a few research organizations. However, due to the comparatively low penetration performance, the amount of research has not been extensive, and the use of this device is quite limited in very specialized applications. Traditionally, the equation of motion of an LSCs’ liner shares the same basis as conical shaped charges (CSCs) because they are under the same functional category and generally have similar geometric configuration. However, the nature of LSCs is not quite similar with that of CSCs due to multiple reasons, and they required a new set of equations to properly address their performance. In this paper, we reviewed different sets of approaches in describing the liner collapse behavior of LSCs mostly based on the author’s contributions.

Jan 1, 2014

By Lina Lopez, Jose Sanchidrian, Manuel Lopez, Pablo Segarra

Previous work in which rock properties and blasting parameters (geometry, charging and timing) were reported together with truck filling times, is taken as a starting point for a thorough analysis of the influence of the former on the mucking velocity. The experimental set was composed by 11 blasts made in an open pit mine. Non-parametric, distribution-free statistics is applied. The mucking rates (in bank cubic meters per unit of bucket volume and per hour) appear to be clearly dependent on the explosive energy and powder factor, both magnitudes combined as energetic powder factor (energy per unit of rock volume). The mucking rate is a non-monotonic function of such factor in the range of the blasts analyzed. The determination of the function is optimum when the fraction of the explosive below grade is not considered and when the explosive energy is qualified as that delivered at a partial detonation regime. Different types of loaders seem appropriate for different energy levels. At low levels both front loaders and rope shovels obtain small productivities without a statistically significant difference in their performance. At high energy levels, front loaders qualify higher than rope shovels. Mucking velocities can be equally small at low energy powder factors and at high ones if rope shovels are involved.

Jan 1, 2008

By Bethany Witter, Dyno Nobel

In the past decades, a technological explosion has caused generational shifts. First, millennials experienced a technological shift to computers and cellphones. Next, Generation Z experienced a shift to smart phones and social media. These two generations are immersed in technology and are accustomed to constant connectivity. How do the extractive and construction industries gain the interest of younger generations and integrate them into the industry?

Feb 1, 2020

By Cameron McKenzie, John Heilig, Patrick Andrieux, Andree Drolet

It is widely accepted that both underground and surface blasting operations can de-stabilise excavations to the point where it can threaten the feasibility of mining through personnel safety or OK dilution. Research has been undertaken to outline a practical method in which the impact of blasting will be accounted for during the early excavation design stage by modelling, and during the following production stages by monitoring rock response to blasting operations.

Jan 1, 1994

By Hu Wenjun

This paper changes the section of copper of copper to aluminum adapter bar into aluminum plate covered one face or double face with copper coat, and changes the conductor material of knife switch, fuse box, plug and socket into steel plate covered one face or double face with copper plate, and manufactures the composite (two layers or three layers) metal plates by means of explosion welding with the plates installed horizontally. Introduced in this paper are the blasting designing technique, manufacturing process and the electrical performances of the explosion bonded products. Besides, this paper presents the designing and manufacturing technique of cumulative charges and their time detonating units for cutting off the retired nuclear submarine pipes. Experiments on cutting off the stainless steel pipes by cumulative flow and on the time detonation are made. Keywords: explosive welding, electric, explosion bonded products, retired nuclear installation; pipe; blasting cutting; cumulative charge; time detonation

Jan 1, 2000

By Bethany Witter

In the past decades, a technological explosion has caused generational shifts. First, millennials experienced a technological shift to computers and cellphones. Next, Generation Z experienced a shift to smart phones and social media. These two generations are immersed in technology and are accustomed to constant connectivity. How do the extractive and construction industries gain the interest of younger generations and integrate them into the industry? The Virginia Tech Student Chapter of the International Society of Explosives Engineers handled this same issue with its recruitment efforts and event planning from 2017-2019. The first critical component of integrating Generation Z college students into the extractive industries is clear and frequent communication via email. Next, Generation Z often values the motivation behind work when choosing a career, so advertising technological advancements, benefits, and ways people can contribute to improving the industry also helps attract young generations. Similarly, advertising opportunities for people to work outside with their hands, travel, and secure stable careers can attract students. At Virginia Tech, the most effective way to attract and maintain the interest of students in extractive industries is to put the students in the field. Field trips to mines and factories experienced the most stable attendance and highest survey reviews of all other chapter events. Guest presentations from industry professionals were often well attended, but attendance tapered off as the academic year progressed and students grew busier. Periodic trips throughout the year maintained student engagement and often supplemented their curriculum. The student chapter was relatively successful in attracting students, but it struggled to maintain attendance levels in the latter portion of the academic year. In the future, the industry can increase its recruitment of Generation Z and Millennials into the workforce by working more closely with university programs to provide resources and opportunities for hands-on experiences for students.

By William McFerren, Pragasen Moodley

In contrast to global trends, African, especially South African, surface mining operations have shown a significant rate of adoption of Electronic Detonators (ED’s) over the last few years. Proven benefits of converting to ED’s from pyrotechnic initiation systems have aided this market conversion. These benefits are experienced throughout the mining operation. Benchmarking exercises, prior to the introduction of ED’s, form part of the conversion process and allow for quantifying improvements. Extensive work has been done on quantifying the benefits of converting to ED’s and have shown that results can be reproducible. Improvements have been experienced in many applications and include environmental impact control, improved mining efficiencies, increased cast benefit and improved size distribution. These step changes in blasting results, in conjunction with the adoption of ED technology have aided the rapid conversion of the African surface market.

Jan 1, 2004

By Tony Francelj, D. Scott Scovira, Remi Proulx

The Meikle Mine is a high-grade, underground gold mine that utilizes a primary and secondary stoping method with delayed backfill. The newly developed Rodeo Mine will start production using similar mining methods in late 2001. The combined production for the mines will be 4100 stpd of ore in 2002. Dilution of the secondary stopes resulting from blast induced overbreak of the backfill placed in the primary stopes was an issue identified as being a major contributor to the total mining cost at the Meikle Mine. To address the overbreak issue, a low-density, polystyrene enhanced bulk emulsion was developed and introduced to the mine. The density and energy of the emulsion was varied until an optimal level was reached. The use of a low-density bulk emulsion has greatly reduced the overbreak of the primary stope backfill when blasting the secondary stopes. Benefits to the mines include reduced secondary stope dilution, lowered total mining cost, and increased revenues.1

Jan 1, 2002

By R C. Berglund

Since the Republic Mine began production in the mid 1950's, drilling and blasting practices have continually changed. In recent years, progress has been achieved through the development of more precise blast engineering methods, in greatly increasing the use of non-water resistant ammonium nitrate explosives, and in changing to a non-electric in-hole delay initiation system. Also, recent experience indicates that ammonium nitrate fueled with nitropropane and methanol is a viable substitute for aluminized AN-FO.

Jan 1, 1980

By W. J. Birch

The recording of information is critical to the blasting process, whether it be for planning purposes, statutory requirements or environmental compliance. The review and analysis of past data can play a key part in a blast.s design. Statutory records must be held to preserve operational licenses and well-maintained monitoring records are a vital defence for today.s litigious society. However a single blasting event can be responsible for generating vast amounts of data. This information maybe collected pre or post-blast and in their individual ways may have a requirement to be logged, processed, analysed, reviewed and reported before eventually being archived.

Jan 1, 2002

By Campbell Robertson

The evolution of electronic detonators in commercial mining, construction and demolition has been a transformative journey, characterized by technological innovation, enhanced safety measures and improved precision. This abstract explores the historical progression and key advancements in electronic detonator technology highlighting its impact on the industry as well as the challenges in deploying these types of technologies. Electronic detonators represent a significant departure from traditional initiation systems offering precise timing capabilities and improved reliability and safety. The early development of electronic detonators can be traced back to the late 20th century with the introduction of basic electronic initiation systems. These early iterations provided a glimpse into the potential for greater control and accuracy in blasting operations. As technology progressed, electronic detonators underwent significant refinement incorporating advanced features such as programmable delay times, multiple firing sequences, expanded blast size and enhanced communication capabilities. These advancements revolutionized the way explosives are deployed in mining and demolition applications enabling engineers to tailor blasts to specific geological or environmental conditions and structural requirements. One of the most notable developments in electronic detonator technology is the integration of microprocessor-based control systems. These systems allow for precise calibration of detonation parameters, including timing, sequence, and energy distribution. By leveraging microprocessor technology electronic detonators have become increasingly sophisticated offering unprecedented levels of precision and safety in blasting operations. The advent of wireless communication technologies has further augmented the capabilities of electronic detonators. Wireless detonation systems enable remote initiation and real-time monitoring of blasting operations enhancing safety by reducing the need for personnel in hazardous environments. The evolution of electronic detonators has also been driven by a growing emphasis on sustainability and environmental stewardship. Modern electronic detonation systems are designed, amongst other objectives, to minimize environmental impact, achieve optimal fragmentation outcomes and reduced misfire rates during blasting. These advancements not only improve safety for workers and surrounding communities but also contribute to a more sustainable approach to mining and/or demolition activities. In conclusion, the evolution of electronic detonators has transformed the landscape of commercial mining and demolition offering unprecedented levels of data integration, precision, safety, and environmental responsibility. As technology continues to advance, electronic detonators are poised to play an even greater role in shaping the future of blasting and explosives engineering.

Jan 21, 2025

By Thierry Bernard, Pierre M. Vuillaume, Michel Kiszlo

In the context of its studies for the french ministry of the environment and for the French national coal board, INERIS (the French institute for the industrial environment and hazards, formerly CERCHAR) has made a complete critical survey of the methods generally used to reduce the levels of blasting vibrations.

Jan 1, 1996

By Alday B. Andrews

A computer program called Seiswise that predicts the character and intensity of ground vibration generated by surface blasting operations was developed and field tested. The program uses the time histories of one or more pilot shots in combination with various initiation sequences to construct synthetic seismograms which are examined to select designs that will produce low levels of ground vibration.

Jan 1, 1990

By Ray Heater, Qian Liu, Alan Bauer

The channel effect is a phenomenon that takes place with decoupling explosive charges; an air shock wave propagating ahead of the detonation wave in the annular space around the explosive charge compresses the charge so that the process of detonation is modified and even stopped. For commercial explosives, such as AN/FO slurries and emulsions, the channel effect causes partial detonation under certain conditions. To simulate and evaluate the phenomenon, a hydrodynamic model was developed based on the assumption that the pre-shock wave is produced by Mach reflection at the tube walls. Based on instrumented experimental studies with the above explosives in diameters ranging from 25 to 90 mm in pipe sizes ranging from 35 to 127 mm, it has been possible to demonstrate that a criterion for failure based on a critical impulse concept fits the experimental data well. Critical impulse values for the various explosives tested are presented along with the necessary correlations between charge and borehole diameter required to produce this.

Jan 1, 1988

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Simav Bargu, Savas Gorgun, Derya Kucukbrtem, Esat Tansev

Although many research studies had been carried out in the past in order to eliminate environmental issues produced from blasting unfortunately a general approach or formula has not been established yet because of the complexity of the matter. In addition to the wave and ground motion characteristics, the complexity of blasting parameters and site factors restrict the developing of a general criterion. So experimental site-specific studies should be still done in order to predict and control blasting effects.

Jan 1, 2002

By John Horgan, Ethan Marcoux

Explosives have been used to demolish many unsafe structures around the world. However, it is unlikely any demolition job has ever involved destroying buildings already buried 40 feet (12 meters) into the world’s largest ice sheet. That is what happened to the original research station at the geographic South Pole, built back in the 1950s, following a series of discrete explosions between 2011 and 2013.

Jan 1, 2015

By Duane Skidmore, Francis Otuonye, Calvin J. Konya

Proper stemming not only affects the rock breakage process, but also controls the unwanted side effects of blasting such as airblast, ground vibration, and flyrock. Little research has been conducted on the behavior of borehole stemming material under high pressure loading conditions. The methods of selecting stemming particle size and necessary stemming length were previously determined only by trial and error in the field.

Jan 1, 1982

By Charles G. Wade

In the ensuing years nitroglycerin-based dynamites will continually be replaced by water-based explosives. Until recently, the choice of a high explosive water-based product was limited to some type of water gel. Now, there is another choice. New emulsions are available having several degrees of sensitivity over a wide range of diameters. This paper discusses the properties of these new emulsions, e.g., physical and thermochemical; the relationship between diameter and explosive properties; and the effects of aluminum on total energy. There is also discussion of some of the unique properties of emulsions, their advantages, and how they differ from water gels.

Jan 1, 1978

By Donald D. Eilers, Pharis E. Williams, Thomas O. McKnown

The Continuous Reflectometry for Radius vs. Time Experiment (CORRTEX) system was developed by the Los Alamos National Laboratory for determining the energy released in a nuclear explosion by measuring the position of its shock front as a function of time. The CORRTEX system, fielding techniques, and the methods and software for data reduction and analysis were developed over a 15 year period with hundreds of measurements made on nuclear tests and high explosive experiments. CORRTEX is a compact, portable, fast-sampling, microprocessor-controlled system, based on time domain reflectometry, requiring only a 24 volt power source and a sensing element. Only the sensing element (a length of 50 ohm coaxial cable) is expended during the detonation.

Jan 1, 1995