Search Documents

By Jared Redyke

Thursday, October 14, 1999 marked another important milestone for America’s space program. At exactly 10:05 AM EST on a beautiful, sunny Florida morning, Dykon, Inc. of Tulsa, Oklahoma detonated approximately 300 pounds of explosives to fell the seven million pound Umbilical and Mobile Service Towers at Space Launch Complex 41 (SLC-41) at NASA’s Cape Canaveral Space Station. Completed in 1965 at the height of the Space Race to the moon, the Mobile Service Tower/Umbilical Towers (MST/UT) were part of the Titan rocket launch facilities. The MST was 265 feet high and weighed over five million pounds. The UT was 175 feet high and weighed over 2 million pounds.

Jan 1, 2001

By Richard J. Mainiero, Michael S. Wieland, Harry C. Verakis

The Bureau of Mines, U.S. Department of the Interior, has been conducting research on delay blasting in underground coal mines in support of the efforts of Mine Safety and Health Administration (MSHA), U.S. Department of Labor, to revise coal mine blasting regulations. Part of the research centered on developing an understanding of the factors that lead to misfires of permissible explosives. Research was conducted to determine whether frequency of misfires was related to borehole spacing. For a wide variety of permissible explosives, misfires were observed for about 50 X of the holes at 45-cm (18-in) spacing. Misfires were also observed for 60-cm (24-in) spacing, but the frequency of misfires was much lower than observed for the 45-cm (18-in) spacing. The Bureau has recommended that hole spacings of less than 60 cm (24 in) be prohibited.

Jan 1, 1986

By Larry R. Fletcher

Excessive flyrock, which is blasted rock that travels beyond the secured blast area, is responsible for 25 pct of the blasting injuries that occur in surface mining. Excessive flyrock is also a frequent cause of damage to mine equipment and facilities.

Jan 1, 1986

By Thomas A. Simpson, Yung-Kwaun Jow, Dennis L. Gamble

Construction of the $200 million Riverchase Galleria Mall in Hoover, Alabama was started in early 1984. The construction area consists of about 70 acres. The extensive building complex requires heavy concrete foundations which have to be poured during the early stages of construction and on a nearly daily situation so that contractual agreements can be met on a timely basis.

Jan 1, 1985

By R W. Givens

This paper presents blast casting design variables that have been developed and are currently being used at the High Power Energy mine in West Virginia. The shot specifications are summarized in Table I. The two active casting pits were designed with casting in mind and as a result are better designed and more efficient. About 55% of the overburden material is effectively cast and clean up is done by a bulldozer, front-end-loader, and trucks. This results in a 15X decrease in the cost of coal production.

Jan 1, 1988

By N H. Maerz

The digital image analysis program WipFrag has been developed under contract to INCO for use in quality control of underground blasting operations. This paper outlines the relevance of fragmentation to underground mining, the hardware and photography requirements, and key features and operating principles of the software.

Jan 1, 1995

By Herschel Sanson

Success of underground blasting operations depends upon a number of interrelated factors. These include conditions at the place, blasting methods, face preparation, type of cap, powder selection, transportation and storage. In addition, much of the work is closely regulated by state and federal regulations.

Jan 1, 1975

By J Mensah, G C. Sen

Often large boulders of rock have to be fragmented in civil or mining engineering operations. These oversize boulders are encountered after primary blasts in both surface and underground excavations of minerals. Various methods are employed to break large boulders into a manageable size for loading and crushing. These methods range from mechanical breaking (such as drop-ball and hydraulic impactor) to the use of explosives. Apart from these, static agents (such as expanding chemicals) are used in special circumstances.

Jan 1, 1989

By Jim Daly

The word “Enron” has taken on a totally different meaning since its leaders were caught juggling the books, President Clinton’s reputation was destroyed not by what he did but by how he tried to cover it up, Martha Stewart spent time in prison for not being honest. Our society is tolerant of mistakes we humans make but has become very critical about what we do following those mistakes. The blasting industry is in a similar position. We have all heard the stories of the tree stump that came down through someone’s roof, of the windows that were broken, of the casualties that occurred when a blast was not properly guarded. What was done following these incidents? In the mind of the public, not enough.

Jan 1, 2007

By Andre Koekemoer, Gys Landman

At the moment, electronic initiation is migrating from a position of a specialist niche to that of a more widely applied technology. Ease of use and deployment rate are becoming aspects of greater concern for end users.

Jan 1, 2011

By B T. Lusk, John J. Silva Castro

The signature hole method uses a convolution operation to predict the waveform of a production blast based on the record of a waveform produced by a single blast hole. Convolution is a mathematical operation on two functions, (generally the product) to produce a third one. Recent research communication and publications highlight a lack of discussion in the literature about the available methodologies to calculate the convolution for blast vibration prediction. The goal of this paper is to discuss and present in detail for students in ground vibrations from blasting, several techniques to calculate the convolution between signals when the signature hole method is used. Convolution is a straightforward operation when signals produced by each hole are assumed the same, however; variations in the signals from each hole in a production blast require a more complex convolution operation. A graphical procedure is shown in this paper to solve a convolution when signals vary hole-to-hole (as expected in a mining production blast). The graphical methodology was tested using a recorded blast event and the results were compared to the regular mathematical procedure (convolution) and the results from a commercial software used in the mining industry. Results show that the graphical procedure is in agreement with the results from the other two.

Jan 1, 2014

By Jon Andrews

Purpose: To show how in managing risk in avalanche control blasting has changed throughout the years, and try to define the term “Acceptable Risk”. History: The history and the way we manage risk in avalanche control blasting to the avalanche control crews and public has change over the years dramatically. From the mid 1800s to about 1920 was the Risk vs. Rewards era, the Industrial Revolution. Now it is a Risk vs. Liability, the age of Liability.

Jan 1, 2009

By H. Bilgin, Sedat Esen

In this paper, the ground vibrations induced by blasting for stripping work at Sekkoy Open Cast Coal Mine belonging to TKI Yenikoy Lignite Mine (YLI) are investigated and the procedures for monitoring and control of ground vibrations are presented. Ground vibration measurements are conducted in the direction of Turkish Electricity Authorities’ Yenikoy Establishment and social facilities because of the complaints and annoyance arising from this site. Forty ground vibration records are taken in this direction and the vibrations are measured in transverse, vertical, longitudinal components together with peak vector sum. After then the scaled distance relationship is determined at 95% confidence value. Further, Fast Fourier Transform analyses are carried out to determine dominant frequencies for both ground and the structures and amplification factors. When the records taken at four different structures together with the ground are evaluated, it is observed that one of the apartment buildings is amplified the amplitude of longitudinal component 4.3 times. The maximum allowable amount of explosive that can be fired safely at this mine is calculated and recommended on. In the determination of safe amount, 95% confidence line, USBM RI8507 and OSMRE criteria, the dominant frequencies of both ground and the structure, amplification factor and the human response are taken into account.

Jan 1, 2001

By Harnish Miller, Scott G. Giltner

One of the concerns with locating radioactive waste storage sites in salt deposits is how to permanently seal the underground storage areas once they have reached their storage capacity. The compaction of salt using explosives has been identified as a potential method of producing permanent seals in both entryways and shafts to storage areas. This paper describes the test procedure and results of a preliminary investigation to determine the feasibility of utilizing explosives in the compaction of salt. Three simple tests were carried out to measure the degree to which loose salt could be compacted.

Jan 1, 1996

By B. A. Cheeseman, R. Skaggs, C. F. Yen, S. Wolf

Shallow buried explosives pose a significant threat to lightweight vehicles and their onboard personnel. To date, designers of lightweight vehicles are limited in their knowledge of what occurs during the blast. The high intensity, short term loading imparted by the explosion is enormously complex and can be significantly affected by a number of parameters including the size, shape, type, detonation point and depth of burial (DOB) of the explosive and the type, density and water content of the soil. Recent advancements in numerical simulations have enabled the complex blast event to be accurately modeled by coupling Eulerian and Lagrangian analyses: the former is well suited to modeling the blast and while the latter, the structural response. Further validation of the modeling technique is considered in the current paper, which details simulations performed utilizing the coupled Eulerian-Lagrangian analysis to the study the blast output of explosives buried in saturated sand. These experiments varied explosive charge size, its depth of burial, the target stand-off (SO) distance and target plate dimension. The investigation concludes with a discussion of the accuracy of the numerical simulations when compared with the experimental observations.

Jan 1, 2005

By Yonghun Jong, Chungin Lee

The main purpose of this study was to apply the artificial neural network (ANN) models to determine optimal powder factors and predict peak particle velocities, based on a series of observations and input parameters. The used blasthole pattern was V-cut. The locations of blastholes and ignition patterns remained almost constant. The input parameters were 14 geological conditions (i.e., dip, dip direction, spacing, separation, and persistence of 2 discontinuity sets, tunnel orientation, rock strength, RQD, and RMR) and 4 blasting conditions (i.e., distance between blasting points and measuring points, charge weight per delay, drilling length, and blasting efficiency). Data for the ANN application in this study were recently collected in a highway tunnel under construction in Korea. The main rock type in the site was biotitic granite. An optimum ANN model was determined by training models with collected data. The trained model was used to evaluate the prediction capability of the optimum model. It was shown that the ANN model could predict the powder factor and the peak particle velocity depended upon the selected input parameters. Particularly, the ANN model predicted more accurate peak particle velocities than those obtained by the blasting vibration equation. Moreover, the more dominant factors among the input parameters could be determined by analysis of the relative strength effect.

Jan 1, 2002

By Hapsari Rosa, Ross Cowie

Conventional blasting activities in the mining process use various types of explosives, with the primary raw materials being Ammonium Nitrate and diesel fuel. The quality and specifications of the two raw materials significantly affect the performance of explosives. One program from the Indonesian Ministry of Energy and Mineral Resources requires mixing 30% Bio Diesel 30 with 70% diesel fuel oil in several industrial sectors, including mining, to reduce greenhouse gas emissions and stabilize CPO prices. This program aims very well for environmental sustainability and the palm oil business. However, it turns out that this change impacts the performance and results of the blasting process in the mining industry, which is the appearance of fumes. This paper will discuss the tests carried out in the laboratory on Bio Diesel 30, the explosive products used, and rock samples were taken from a mine in East Java, Indonesia. The aim is to determine what factors can cause fumes utilizing a mixture of Bio Diesel 30 with pure diesel fuel. The parameters tested were visual differences, infrared spectrometry, density and viscosity, surface tension and contact angle for Bio Diesel 30, stability test for explosives, and the SEM-EDS method for rock samples.

Feb 6, 2023

By Ron Woolf, Corry Goumans

This paper describes rock slope remediation performed along America’s first Superhighway, the Pennsylvania Turnpike and in particular, the specialized drilling equipment designed and built by Pacific Blasting to complete this work. This S-month project was performed on an existing rock cut slope within the Bedford Narrows, a gap formed by the Juniata River through Evitts Mountain. These rocks are in the folded Juniata and Tuscarora Formations within the Valley and Ridge Province and strike northeast with near vertical to slightly overturned bedding.

Jan 1, 2001

By Lon D. Santis

This paper reports on an evaluation of the safety characteristics of short lead, 5 centimeter (cm), Magnadet1 detonators. The Magnadet initiation system uses magnetic induction principles to transfer electric energy from the firing line to the detonator without a physical connection. This study was initiated because the Magnadet initiation system represents a new technology and the Bureau is interested in ensuring that no potential safety hazards are introduced into the nation's mining environment. The Magnadet system and its proper use are described along with a discussion of how it works. The potential hazards examined are: stray current from mine service power, lightning, DC current, static electricity, and radio frequency transmissions. Tip strength is also evaluated. Experiments were conducted to evaluate some hazards and theoretical methods were used to evaluate others. The results showed that the Magnadet short lead initiation system does not exhibit any unusual safety hazards. The new system is at least six times as resistant to common hazards as currently used electric initiation systems, so long as the insulation is intact.

Jan 1, 1992

By Randy Wheeler

In recent years the issue of seismograph calibration and accuracy has been a major focal point of the ISEE Blast Vibration and Seismograph Section. In fact, questions concerning the consistency and reliability of seismograph measurements essentially led to the development of this ISEE section. One of the early actions of the section involved the development of “Field Practice Guidelines” for the use of seismographs. These guidelines specifically state that “Placement and coupling of the vibration sensor are the two most important factors to ensure accurate ground vibration recordings.” This paper will address the results obtained from using different coupling methods to record vibration and airblast levels generated from production blasting in a limestone quarry. The data obtained clearly indicate that seismometer burial provides the best coupling for recording ground vibrations. Microphone height has also been an issue regarding the accuracy of recorded airblast levels. The data we obtained indicates that microphone height is not a significant factor.

Jan 1, 2004