Search Documents

By Aditya Ayithi, William G. Ryan, Dean Herbst

"For rock socketed drilled shafts, it is a common practice not to include the frictional resistance of overburden soils into the nominal capacity estimation. The primary reason often being cited is “overburden soils resistance is negligible compared to that of rock socket resistance.” However, in certain geological conditions, where the rock layer is located at greater depths, friction resistance from overburden layers can be significant. In addition, at such great depths, shaft drilling becomes very complicated and expensive. In these situations, considering the resistance of the overburden layers can be an economic alternative.This paper presents a case study of an Osterberg cell (O-cell) load test conducted on a 161.8 feet long and 78-inch diameter instrumented test shaft. Based on initial designs, a 72-inch diameter rock socket of lengths 23 and 26 feet was required to provide a LRFD factored friction resistance of 3,200 kips. The load test results revealed that the material in the 72-inch diameter socket does not represent a true rock. However, the test results also proved that the factored friction resistance of overburden layers is greater than the required design resistance. Based on the load test results, it was decided to allow the overburden soils frictional resistance to be considered in the shaft design, resulting in significant economic savings.INTRODUCTIONRock socketed drill shaft design guidelines of various State Department of Transportation (DOTs) agencies allow friction and/or end bearing resistance of only the rock socket portion into the design capacity estimation. It is typical to neglect the frictional resistance of overburden soils. However, in certain geological conditions where the rock layer is at greater depths, friction resistance of the overburden soils can be significant. In this case the friction resistance of overburden soils was verified via the specified instrumented O-cell test program and then used as part of the design capacity.PROJECT DESCRIPTIONAs part of I-29 improvement project, Iowa Department of Transportation (Iowa DOT) planned to replace the dual four lane bridges that cross the Floyd River in Sioux City, Iowa with dual six lane bridges (Fig. 1). Expected benefits from this improvement include improved safety, traffic operations and roadway infrastructure conditions.BRIDGE SUBSTRUCTUREThe project consists of two individual bridges; a new south bound bridge and a new north bound bridge. The south bound bridge is 646-ft long and the north bound bridge is 644-ft long. Both are six-span, pretensioned and pre-stressed concrete beam bridges of varying width. Bridge foundations were designed such that the abutments of both bridges will be supported on driven steel piles and the bridge piers will be on drilled shaft foundations."

Jan 1, 2016

By B. Philip Shull, Allen W. Cadden, Johanna M. Simon, Michael S. Senior

A 670 linear meter (2,200 linear foot) large-diameter sanitary sewer interceptor installation at depths ranging from 3 to 10 m (10 to 30 ft) below existing grade in an area with a high water table requires careful attention to design and performance of the system during construction. Highly variable soil and rock conditions at the site necessitated the design and construction of various excavation support systems along the alignment. In addition to the subsurface condition challenges faced at this site, the proposed sewer pipe was to be installed between an existing active combined sewer main and a high pressure gas main feeding the nearby city. What better way is there to monitor performance of the system than to require a detailed instrumentation system? Instrumentation system specifications and designs are becoming more commonplace in the industry, but it is always important to sit back and take a look at the whole picture. What are you looking to gain from your monitoring? What pieces of information are useful? What interpretations can you derive from the instrumentation you have selected? This paper will address the instrumentation system used to monitor the 670 m (2,200 ft) excavation from the specification requirements to the implementation and interpretation. This case history will delve into the challenges faced and methods used to overcome those challenges on this particular support of excavation (SOE) project. A combination of soldier pile, lagging and sheeting, and shoring systems was used to achieve the necessary excavation support. In designing the systems, attention was given to the configuration of the bracing system to allow the sections of largediameter pipe to feasibly be installed in the excavation while maintaining the SOE system.

By Juan M. Pestana, Jeremy M. Gasser, Cuneyt Gokmen, Paul J. Sabatini, William Tanner, Daniel J. Woeste

An access pathway and working platform were designed and constructed for equipment access for a Deep Soil Mixing (DSM) pilot study over a coal combustion residual (CCR) surface impoundment (SI). The DSM pilot study was conducted to evaluate slurry mix designs and construction techniques for installing DSM columns up to 95 feet deep. Two-dimensional (2-D) limit equilibrium and 2-D finite element analyses were used to evaluate multiple failure mechanisms including: (i) bearing capacity, (ii) punching shear of mixed ground and underlying CCR, (iii) effect of fluidized DSM columns on working platform stability, and (iv) liquefaction. The analysis results were used to design ground improvement required to increase bearing capacity and stability of the CCR under the proposed equipment access route. A long-reach excavator was used to perform shallow bucket mixing and walk onto the CCR SI atop previously mixed cells following a minimum cure time and acceptance of quality control test results. Prior to mobilizing the DSM rig, a static load test was conducted to evaluate performance of the working platform. Both the access pathway and working platform demonstrated acceptable performance under the design loads during the DSM pilot study. This case study emphasizes the economic and safety benefits that can be realized by appropriately designing critical temporary work items such as access pathways and working platforms in difficult ground conditions. INTRODUCTION A Deep Soil Mixing (DSM) pilot study was conducted at a coal combustion residual (CCR) surface impoundment (SI) to evaluate slurry mix designs and construction techniques for closure design of the SI (Site). Sluicing of CCR at the facility ceased and closure will be initiated based on requirements in the final United States Environmental Protection Agency (USEPA) Rule for Disposal of Coal Combustion Residuals from Electric Utilities, 40 CFR 257, effective October 19, 2015. The proposed closure approach involves constructing a DSM containment structure (DSM Wall) to separate the SI into two areas: (i) a closure by removal area; and (ii) a consolidate and cap-in-place area. The proposed DSM Wall would retain the CCR within the consolidated closure footprint and provide a barrier between the two areas of the SI. The predominant CCR in the SI where the pilot study was conducted were fly ash and bottom ash. CCR materials in surface impoundments are generally soft and saturated as a result of being sluiced into place and can present stability and safety challenges when performing earthwork activities.

Jan 1, 2019

By Franz-Werner Gerressen, Manfred Schoepf

"Diaphragm walls are known as underground structural elements commonly used as retention systems for excavation pits and shafts and permanent foundation walls or elements. It can be anticipated that, with the increasing trend of utilizing more and more underground space to accommodate environmental considerations and urban/suburban development, there will be an increasing requirement for diaphragm walling in even more complex conditions. Complex and/or challenging conditions in terms of ground conditions have a major impact in regards of choosing the right tools for excavation purpose. Complex conditions in terms of space limitations, especially for inner city job sites, require specifically adapted solutions for slurry, spoil, reinforcement and concrete handling and the related logistic to ensure smooth production. Furthermore, one focus will be given to the QA/QC topics of the production process. Real time installation control, data transfer and reporting systems become more and more important ensuring the five dimensions of a jobsite. Therefore, the paper will describe the construction method and the sequence of activities required for the construction of diaphragm wall systems with the focus on the cutter technology. It will describe also the main equipment which will be needed to execute these works under the various conditions INTRODUCTION Diaphragm walls are known as underground structural elements commonly used as retention systems for excavation pits and shafts and permanent foundation walls or elements. It can be anticipated that, with the increasing trend of utilizing more and more underground space to accommodate environmental considerations and urban/suburban development, there will be an increasing requirement for diaphragm wall usage in even more difficult conditions. Of course diaphragm wall can also be used as deep groundwater barriers (Cut-Off-Walls). This market has shown that the demand for these types of walls is reaching more and more difficult soil conditions or required depths which are surpassing the current standard. The trench cutter is the most important tool for performing this work. The trench cutter itself is a reverse circulation excavation tool. It consists of a heavy steel frame with two drive gears attached to its bottom end, which rotates in opposite direction around horizontal axis. Cutter wheels are mounted onto the drive gears. As they rotate, the soil beneath the cutter is continuously being broken up, removed, mixed with the bentonite slurry in the trench and moved towards the opening of the pump suction box. The slurry loaded with soil and rock particles is pumped by a centrifugal pump which is located right above the cutter wheels, up through a hose system up to a desanding plant where the slurry is cleaned and returned into the trench."

Jan 1, 2015

By Athena C. Denivo, Pablo V. Lopez, Michael McMaster, Sissy Nikolaou, Alfred H. Brand

"The paper presents the history of development of the United States Tennis Association (USTA) site, focusing on geotechnical, geoseismic, and foundation engineering challenges associated with it. The site is located at the Flushing Meadows Corona Park area of Queens, New York. Now home to the Billie Jean King National Tennis Center (BJKNTC), the site used to be a biologically rich, tidal salt marsh that extended south from Flushing Bay and overlaid an ancient buried valley. In early 20th century, Brooklyn Ash Co. was contracted to fill the marshland with cinders and furnace ashes. F. Scott Fitzgerald describes the “Valley of Ashes” as “a fantastic farm where ashes grow like wheat into ridges and hills and grotesque gardens; where ashes take the forms of houses and chimneys and rising smoke, and finally, with a transcendent effort, of ash-gray men who move dimly and already crumbling through the powdery air.” In 1939 the site was leveled and filled to host the World’s Fair and refilled again for the 1964 World’s Fair.The USTA moved to the site in 1978 and in mid-1990’s constructed the 23,000-seat Arthur Ashe Stadium (AAS). Currently, USTA has a Strategic Vision Plan venue with several interconnected construction projects including buildings, infrastructure upgrades and improvements to site circulation. In addition to a historical walkthrough, the authors will discuss technical challenges of supporting these developments through layers of fill, thick organic silty plastic clays and regional varved soils with bedrock found 300 to 400 feet deep. The subsurface is not only a weak foundation medium, but is susceptible to large amplification of seismic waves propagating from the bedrock during earthquakes. The developments are usually founded on project-specific pile foundations that carry static loads in deeper layers and accommodate lateral demands and performance objectives. Engineering innovations from the most recent development, the roof structure over AAS, will be discussed."

Jan 1, 2016

By James Warner

Investigations of the sinkhole indicated that the loose, disturbed ground was completely encircled by dense competent core. This confinement substantially increased the effectiveness of the compaction grouting compared to what might have been expected at a "greenfield" site. However, the 8 ft diameter circle shown in the plan view was only the surface expression of the sinkhole proper and the deep, loosened ground actually extended to a larger diameter of about 20 ft. The planned spacing of the grout holes was based on the finite element simulations using a target void ratio of less than 0.3 throughout the compacted ground within a 5 ft radius of the grout injection point. Because of the strong confinement effect, the layout of grout holes included one central primary hole surrounded by six secondary holes at a triangular spacing of about 5 ft. Since the disturbed ground was considered a confined cylinder, it was anticipated that the primary hole would perform the majority of work and the secondary holes would act as check holes, with progressively lesser grout takes as the loose ground densified.

Feb 10, 2003

By Sara Anderson, Rachel Nicholls, Tim Chapman, Janice Windle

"In city center sites around the world, and in particular in London, foundation reuse is becoming increasingly widespread as the ground is filled with detritus from previous developments. This paper sets out a systematic framework to consider the need for and benefits of foundation reuse and key issues to be resolved for foundation reuse to be successfully adopted on redevelopment projects. Once foundation reuse has been identified as a potential foundation solution there are several key stages in the design and construction process where the decision to reuse foundations needs to be assessed. The paper concludes by emphasising the importance of ensuring that the foundations being installed now can more easily be reused in the future.INTRODUCTIONThe concept of re-using foundations is not new, and has been adopted on an isolated project-byproject basis for many years. However, over the past decade, interest in the potential of reusing existing piles and caissons within Europe has increased significantly, with a growing interest in the United States of America and Japan. The need has been driven by necessity: on many urban sites the space available for new foundations diminishes with each new set of piles, and these problems can only grow in the future.Initiatives such as the European Union's RuFUS (Re-use of Foundations for Urban Sites) research project have resulted in identification of the key issues for technical viability and risk that have previously hampered potential foundation reuse projects.There is a need to define a systematic approach to the reuse of foundations so that the risks associated with reuse can be identified, managed and mitigated. This requires improvements in knowledge to provide confidence in the long term behaviour of the foundation support and address the risks involved in reusing existing foundations to overcome perceived obstacles in making foundation reuse a realistic option for many sites."

Jan 1, 2005

By Ryan T. Smith, Anthony Sahj, Alexander T. Darnell

Every second can count when trying to board a departing flight or catch a ride-share to your final destination. Hartsfield-Jackson Atlanta International Airport is in the midst of a project that aims to cut about 13 seconds between automated people mover trains (Plane Train) that move passengers between the terminals and concourses. The project involves extending the Plane Train tunnel west from its existing terminus under the domestic terminal. Working from inside non-public areas of the terminal, Keller North America, Inc. (Keller) incorporated systems of micropile-supported steel beams and grillage to both underpin existing columns prior to tunneling and support open-cut excavation at the tie-in of the new to the existing tunnel. Dewatering aided in mining a challenging section at the start of the drive of the mixedface, sequentially excavated tunnel and an automated instrumentation system monitored the performance of the construction and its impact to the terminal. Cut and cover egress and ventilation tunnels required braced support of excavation.

Oct 1, 2022

By Eric S. Lindquist, Charles A. Luxford

The State of Texas recently adopted a master plan to expand the existing Capitol Complex in Austin. Phase 1 of this expansion will add two new State office buildings and five levels of underground parking to the existing Complex. Additionally, a landscaped pedestrian mall will be built atop a portion of the underground parking to enhance the area as a cultural destination. Capitol Complex website: https://www.tfc-ccp.org/ Brierley Associates was selected to provide detailed design of the entire Phase 1 earth retention system for an approximately 40-65 ft (12-20 m) deep, 500,000+ yd3 (380,000+ m3) excavation through overburden soils and limestone bedrock. To facilitate overall project coordination, all design packages were required to develop Revit models, including the retention system package. With the project located in an urban setting, this 3D model also facilitated coordination of the retention system with adjacent major structures and utilities. The retention system is a combination of soil nails, soldier piling with tiebacks and rock anchors with a shotcrete facing as a substrate for the below-grade blindside waterproofing system. Due to the substantial scope of excavation, a significant number of utilities had to be routed on a temporary span over the excavation. Brierley Associates designed this utility support structure, which required extensive coordination with the excavation support and existing utilities located directly underneath the structure’s foundations. Preconstruction geotechnical work identified a fault zone that might be encountered within the excavation; however, the fault feature was found to have a more adverse location and orientation than originally anticipated. This observation required that a portion of the temporary anchors be converted to higher-capacity, corrosion-protected permanent anchors.

By Silas C. Nichols

"Abstract Piling and deep foundations are a staple for transportation projects in the United States (US). Driven or bored piles have been used for everything from support of bridge foundations and retaining structures to support of culverts and embankments on soft ground. Deep foundations have been popular in the US transportation market to better handle large axial and lateral loads, extreme event loading, and to better control structure movement. However, there are challenges in the maintenance of design and construction codes in transportation for consistent and reliable structure foundation elements. A significant amount of effort continues in the US to maintain national codes and specifications at a level consistent with the state of practice, and identify and conduct research for providing safe and cost effective highway structures.IntroductionThe transportation sector in the United States has a hierarchy of design and construction codes that are used for the specification of piling and deep foundations. Any highway or bridge project on the National Highway System (NHS) must be designed and constructed in accordance with a national set of standards approved by the State Highway Departments, and that are acceptable to the Federal Highway Administration (FHWA). However, in any jurisdiction, exceptions are permitted with approval. Therefore, design may be governed by the national standard specification, a state standard specification and design manuals, special provisions, or guideline specifications. Any of these standards, or a combination, may be used depending on the needs of the owner agency.The FHWA and the American Association of Highway and Transportation Officials (AASHTO) have worked together in the development and maintenance of geotechnical design and construction guidance and codes that support the surface transportation community. General geotechnical engineering practice in the United States lacks a singular, national design and construction code that addresses all aspects of geotechnical engineering. As a result, the AASHTO specifications provide the most complete geotechnical specifications focusing on structure foundations, retaining walls, and buried structures for surface transportation applications. This includes piling and deep foundation types commonly used for support of bridges and transportation structures.The FHWA National Geotechnical Team has published several technical guidance documents that include guideline specifications for the design and construction of driven and bored deep foundations. Reference documents published by FHWA summarize the state of practice and provide recommended design and construction guidance. These reference documents have long served as a basis for provisions included in the AASHTO specifications. Maintenance of the design code and specification, and related guidance documents for consistent use on US transportation projects requires a collaborative effort between industry, FHWA, and the member state highway departments that make up AASHTO."

Jan 1, 2014

By Michael W. Neill, O&apos

This presentation addresses some of the problems encountered in estimating the capacity of drilled shafts and augered, cast-in-place piles in soft rock. Methods to quantify side and base resistance are suggested. However, the methods that are described should always be verified locally by performing load tests.

Jan 1, 2001

By Jerold Bishop, Grant Bearss, Aleksey Egorov

"When a shock wave is released in the bottom of a drill hole filled with wet concrete slurry, the result is called an electrohydrodynamic effect, or EHDE. The energy is carried through the fluid with minimal loss because the slurry is an incompressible medium. Repetitive discharges provide a series of energy pulses that compact the soil along the pile shaft and at its base. The process is analogous to repeated applications of low-energy blast densification or to dynamic compaction. In general, the process is not depth dependent. EHDE was identified in the 18th century by an American scientist who observed that a spark between two electrodes placed under water induced a burst of pressure. In 1957, two Russian engineers formulated a process and received a patent for a method of creating a pressure wave by transforming power from an electrical discharge to a mechanical impact. They derived more than 200 applications for technical and industrial processes.In the 1970s, civil engineers at the Engineering and Building Institute in St. Petersburg, Russia, began to look at EHDE to improve the capacity of drilled piles. Early experiments showed that electric discharges in a wet concrete slurry mix could create a pressure wave of up to 26 MPa (3700 psi). Later tests demonstrated that this pressure level could be created in a drilled pile hole. The researchers devised equipment and in the early 1990s began to study pulse technology as applied to drilled piles.This application was accepted into the Russian Federation Building Code in the 1990s. The code treats “regular” drilled piles with equivalent bearing area as having roughly half the capacity of a driven pile. However, the code considers drilled piles treated with the EHDE technique a direct “one for one” substitution for driven piles and allows higher values if the capacity is established by static load testing. Hundreds of projects have been completed in Russia using this technology to value engineer drilled pile projects. In several instances, the number of drilled piles installed was fewer than half of the number originally planned for due to the capacity increase that EHDE-treated piles provided.Drilled PilesIn drilled pile construction, the EHDE process creates a mechanical pressure wave that impacts the base and sidewall of a drilled pile shaft. Soft, poorly consolidated or loose soil is compacted by successive pulses of pressure created by electrical discharges. These mechanical impulses are made by inserting a discharge probe into the wet concrete slurry. A discharge across the tip of the probe creates the pulse that travels outward to the sidewall and base of the drilled pile through the incompressible medium of the slurry. The power pack ratings for equipment presently in use are 35 and 50 kJ (kilojoule).Each pressure wave strikes the soil, causing compaction and expanding the hole. Workers apply the pulses until the size of the hole stops increasing. They watch the slurry level during pulsing. When the level quits dropping, further soil compaction in the drill hole sidewalls and base is not possible. After the pulse process is complete, workers insert a rebar cage and the pile is finished.The process does not alter the soil mineralogy. The electrical discharge is internally grounded and does not arc to the sidewalls of the drill hole. Soil is not scorched or altered in any manner; it is only compacted by the pressure wave. This technique has been used in urban areas with no effect on electrical or electronic equipment."

Jan 1, 2009

By Dempsey S. Thieman

Innovative marine bulkhead design and construction techniques were used in the fast-track design and construction of a high-capacity, deep-water dock in the highly seismic region of Alaska?s Aleutian Islands. The geotechnical investigation and design through construction phases were completed in just eight months. The adaptable OPEN CELL® design, readily available standard flat sheet pile and an experienced contractor were integral to the successful completion of the project. The cost of the structure was determined to be approximately 50 percent of a comparable pile-supported platform dock structure, allowed higher load capacity, rapid construction, less maintenance, and provided substantially more uplands. This paper details the design and construction of this unique and challenging project. The OPEN CELL structure is a vertical flexible membrane system that offers significant advantages over other structure types: ? Its flexible membrane structure is not dependent on toe embedment for stability. ? Poor soil conditions, shallow bedrock, high seismic loads, deep water, scour, etc., can be accommodated due to its adaptable design. ? It has a very high load capacity?capable of several thousand pounds per square foot. ? Allows buried utilities which results in lower cost and reduces freezing conditions ? The sheet pile tail walls can be extended to provide increased global stability if needed. ? Standard sheet pile and connectors with traditional installation techniques allow accelerated construction schedules.

Jan 1, 2008

By Les R. Chernauskas

Driven pipe piles are commonly used for near and offshore structures due to their omni-directional bending resistance, large surface area, and ease of installation. However, these piles typically cannot be driven deep enough to develop significant and sustained uplift capacity, and in some cases do not generate enough end-bearing resistance before being overstressed during driving. When driven closed-ended, their relatively light weight to cross-sectional ratio, and when driven open-ended their tendency to prematurely plug, are some installation short comings. Spin Fin® piles are traditional pipe piles fitted with flat, steel plates (?fins?) attached at a slight angle over the lower few feet of the pipe. Their design development dates back several decades for projects associated with harsh, limited weather window, offshore Alaskan oil field work. These projects required a pile type that could generate high and sustained capacity in both compression and tension, at relatively shallow depth. During pile driving, a relatively short, high capacity pile translates into more rapid installations with smaller and more efficient equipment. In this type of environment, where pile capacities are large, cyclic loading is typical, and relatively high pile movement is tolerable, the Spin Fin® pile is a superior solution. This paper describes the experience of using Spin Fin® piles on several recently completed Massachusetts Steam Ship Authority projects.

Jan 1, 2011

By Mohamad H. Hussein

A minipile system was employed in underpinning a historical structure in Florida. The existing structure is founded on shallow foundations. Subsurface conditions at the project site consist of deep organic deposits interbedded with loose sand and silty sand. A minipile foundation system was deemed the most appropriate underpinning corrective measure for the already badly cracked structure. A total of 68 minipiles, 3.5 inch OD and 0.25 inch wall thickness closed-ended concrete-filled steel pipes, were installed to depths varying from 55 to 175 feet. Installation was accomplished with a pile driving hammer having a rated energy of 1 kip-ft. Highest required pile design load was 15 kips. Conventional static and wave equation analyses were performed to establish preliminary pile lengths, to assess pile drivability and establish driving resistance criteria. Dynamic pile testing using the Pile Driving Analyzer was conducted on six of the production piles. This paper describes geotechnical design considerations, installation procedures, and dynamic field monitoring. This case represents unique applications of pile dynamic testing and such slender, very long minipiles in compressible soils.

Jan 1, 1993

By A. C. Ackenhell

The geologic environment of Pittsburgh, Pennsylvania is both inviting and challenging to drilled pier installation. The shales and clayey soil zone of the hills are favorable but the alluvial soils of the three major rivers create problems. Beginning in the early 1950's, drilled pier installation continually improved as methods were developed to meet the geologic challenge. Case histories are presented to illustrate the historical development of piers in Pittsburgh. Recent innovations reducing the groundwater problem are illustrated by a case history of a high rise building construction. Load test information for side wall shear on the cylindrical shaft area between the concrete and bedrock continues to be desired but remains generally uneconomical.

Jan 1, 2010

By Kanagarajah Ravishankar

Drilled shaft (caisson) foundations are extensively used in the past. In the central part of New Jersey, the soils consist of silt and clayey silt overlying Triassic age shale bedrock. The shale is friable and generally severely weathered and highly fractured. The shale crumbles readily into small fragments. In general, the shale is encountered in shallow depth. Subsurface investigations indicated that the upper part of the shale is very soft, highly weathered, and able to advance through soil exploration methods. The underlain formation is relatively hard and required rock coring techniques for sapling. Individual core recoveries ranged from 10 to 100 percent and Rock Quality Designations (RQD) vary from 0 to 90 percent. Although several methods available to estimate the axial capacity of drilled shafts, it is a difficult task for the designer choose the suitable method due to self disintegrate nature of the shale. In the recent years several bridge foundations have been constructed using drilled shafts founded on shale rock in the vicinity of the central New Jersey. Based on load tests carried out on drilled shafts during construction, subsurface exploration, and laboratory tests, suitable methods for determining axial capacity of drilled shafts is analyzed. This paper presents the findings of the field tests and suitable methods to determine the axial capacity of drilled shaft founded on soft shale. Key words: Drilled shaft, axial capacity, Osterberg load test, shale.

Jan 1, 2006

By Raymond J. Poletto

This paper describes the special problems that occur with the construction of diaphragm walls and discusses the lessons learned during the repairs of structural walls. Although diaphragm or slurry wall technology and equipment has vastly improved since its development in the late 1950?s, significant problems still occur. Key issues are repairs related to panel joints between wall panels, concrete defects associated with tremie concrete problems, leaks and other defects at tieback reservations or inserts, wall leaks within the plane of the wall and surface repairs. The paper supports the position that diaphragm walls are relatively watertight when properly constructed, but cautions that it is necessary to address potential problems in the design stage and allow for flexibility in construction so that the problems that occur can be corrected once encountered. Due to the fast track nature of most projects the time available for design, detailing and construction is limited. As a result, insufficient attention to detail by any of the responsible parties can lead to imperfections and defects in the wall. The authors describe the nature of these problems and their potential resolution based on ?lessons learned.? The timely response to wall problems is essential to the successful completion of a diaphragm wall project. Appropriate repairs have resulted in largely successful jobs starting with the World Trade Center in New York City. The authors? total 80 years of experience as the engineer of record and designer, inspector and contractor?s representative for the diaphragm wall results in a unique insight to deal with these problems.

Jan 1, 2011

By Dharmil S. Patel, Zoyav S. Benyaminov, Cassandra A. Wetzel

Rehabilitation of the Henry Hudson Bridge is nearing completion, connecting Spuyten Duyvil in the Bronx to Inwood Hill in Manhattan, New York. Constructed in 1936, the Henry Hudson Bridge spans 840 feet over the Hudson River. Challenging geotechnical aspects of this Project required a team of innovators to overcome. Rehabilitation of the existing bridge involved the replacement of sixteen bent pedestal substructures, two abutment pilasters and installation of new deep foundations at the skewbacks. However, the Bridge, roadways, adjacent Metro-North Railroad (MNR) structures and New York City (NYC) Parks land were to remain open to the public for use, with minimal disturbance. In addition to physical constraints, geologic site conditions varied widely across both sides of the River, with varying bedrock quality and depth, greatly impacting the proposed design and construction. Extensive analysis of bedrock conditions was conducted to locate areas of potential wedge failure. The implementation of anchors was used to reinforce rock stability where pedestals and pilasters were replaced. This paper describes several challenging technical and natural aspects overcome in the rehabilitation of the Henry Hudson bridge foundations, including varying geologic site conditions, access restrictions, construction limitations, project specifications and design requirements.

Sep 8, 2021

By Douglas G. Baker, Jason K. Braund-Read, Megan R. Sheffer

"Mica Dam, owned by British Columbia Hydro, is an 820 ft high earthfill embankment dam that was completed in 1973. The dam consists of a thin central impervious till core supported by upstream and downstream compacted sand, gravel and cobble shell zones, founded on bedrock and valley bottom alluvium deposits. In 2012, a project was started to install new piezometric instrumentation within the dam’s foundation and downstream shell zone.Deep drilling in large embankment dams is very difficult and requires careful planning to select a methodology capable of reaching the target locations, while ensuring that no damage is done to the surrounding dam fill zones. At Mica Dam, the drilling could only be carried out from the Dam Crest and drillholes had to be carefully oriented to avoid intersecting any existing dam instrumentation. The drilling work therefore required angled drillholes, at depths of up to 855 ft, through heavily compacted sands, gravels and cobbles, and to significant depths below the standing water table.During the planning stages for the Project, in early 2013, the preferred drilling method was selected and a drilling contractor was engaged for the drilling work. Critical dam safety concerns were identified and addressed during the design stage of the Project with the drilling contractor, so that risk mitigation measures and response plans could be effectively developed.This paper explains how background information and prior drilling experience influenced the final design and implementation of the drilling techniques used in 2013 to successfully drill the deep holes and carry out the piezometer installations in Mica Dam. Drilling procedures, instrumentation design and installation methods, as well as risk mitigation measures, are discussed."

Jan 1, 2017