Search Documents

By Raymond D. Potts

"Minntac is a taconite mining, concentrating and pelletizing operation located near the town of Mountain Iron, Minnesota, U.S.A. It is totally owned and operated by USX Corporation and represents its largest source of domestic iron units. Minntac began producing fluxed pellets in 1988 and has produced both acid and fluxed pellets since then. This paper compares the acid and fluxed pellets produced at Minntac. It reviews modifications that have been made to the plant flowsheet and discusses areas recognized for improvement since the beginning of fluxed pellet production. It also comments briefly on the performance of Minntac fluxed pellets in USX blast furnaces and the future of fluxed pellets at Minntac.IntroductionMinntac was built in three steps with each step designed to produce 6 million long tons of acid pellets per year. The actual production has varied though. Figure I shows the production by year at Mirmtac. Step I began production in 1967, Step 2 in 1972 and Step 3 in 1978. Mirmtac produced 16.5 million tons in 1979 but only 3.5 million tons in 1982 when the facility was shut down for six months because of the lack of demand for pellets. Since the initial start up, Mirmtac has produced over 200 million long tons of pellets. Until 1987, all the pellets produced were ""acid"" pellets. In 1987, equipment to produce ""fluxed"" pellets was installed and tested. In 1988, full scale production of fluxed pellets began."

Jan 1, 1991

By Theo Mayer

Presentation Outline Define data visualization in the context of workflow Present other industries? application and demonstrated benefits Provide conceptual tools to help you address a visualization strategy Hold 10,000 foot view ? to touch on many issues

May 1, 2008

By Philip Thwaites

"Automatic flotation control in varying degrees of sophistication is practiced at a number of concentrators throughout the world. Practically, the variable conditions in the flotation circuit and the difficulty in maintaining accurate instrumentation information all add to the complexity of automatic control.Further development at the Kidd Creek concentrator has resulted in a 3075 mtpd copper flotation circuit capable of running twenty-four hours a day under the direct control of an optimizing supervisory computer.Three main streams, continuously monitored by an XRF analyzer, supply circuit information to the optimizing computer. Circuit efficiency calculations (from smelter contract terms) and target setpoints allow the computer to determine the economic optimum direction to move the circuit based on the grade/recovery relationship. Circuit manipulation is accomplished by precise pumping of collector and frother reagents together with accurate control of flotation bank pulp levels. The former uses computer controlled diaphragm pumps and the latter is achieved by control loops utilizing a float type level transmitter, variable position dart plugs and a process computer working to setpoints determined by the optimizing computer.The development of a fully automated flotation circuit is by no means complete, but increased knowledge and major hardware improvements have allowed its progression to a higher level of sophistication.IntroductionThe Kidd Creek concentrator is located twenty-six kilometers east of Timmins, Ontario, within a metallurgical complex including a 109,000 mtpy zinc plant and a 59,000 mtpy copper smelter and refinery. The concentrator treats two ore types, a copper-zinc ore and a copper-silver-Iead-zinc ore, at a combined rate of 4,500,000 mtpy. Flotation of the crushed and ground ore yields copper and zinc concentrates from the copper-zinc ore and copper, lead and zinc concentrates from the copper-silver-lead-zinc ore."

Jan 1, 1983

By Orlando Rojas, Javier Pizarro, Romke Kuyvenhoven, Francisco Soto

"The concept of geometallurgy has been extensively mentioned and used in the mining industry in the past years. However, each mining firm has a different understanding of what geometallurgy means, and its actual value varies significantly from site to site. Even in the case of properly constructed geometallurgical models, it is fairly common to observe a sub-utilization of the model in the actual operation, because of its low production forecasting capability on the short term. This disconnect between the geometallurgical model and operations is typically caused by a lack of tuning between the original model and the actual plant operation. Also, the absence of procedures and other standards for reconciliation, affects the confidence and the predictive quality of the model. The geometallurgical model should consist of three different levels: (I) adequate capture of information, (II) data analysis and modelling, and (III) development of the block model. Once the geometallurgical in-situ model is finalized, a process model should be developed of the plant at industrial scale, in order to scale up the in-situ geometallurgical parameters from their base or standard condition, to the actual operating reality of the plant. Finally, the stage of reconciliation will close this process, assuring that any deviation between the geometallurgical model and the actual plant operation is not due to lack of tuning, but due to operational issues such as unattended maintenance requirements or poor process control in the operation. The methodology as described in this paper has been applied at several large mining sites in Chile. The paper presents the characteristics of the proposed methodology, and quantitatively describes its benefits with examples from actual operations.INTRODUCTIONIt probably is fair to say that geometallurgy became widely used in greenfield projects in the Andes region during the mining boom of the 90’s, when massive orebodies were studied and developed, and upfront metallurgical characterisation proved its use for accurate economic evaluation including estimates of plant throughput, energy consumption, final product quality and overall recovery. A few examples of such greenfield studies for concentrator plants in the 90’s are Minera Los Pelambres (Antofagasta Minerals, Chile), Minera Escondida, Laguna Seca (BHP Billiton, Chile), and Rio Blanco (then Montterrico Metals, Peru). Large size hydrometallurgical operations such as Cerro Colorado, Quebrada Blanca and Lomas Bayas (all in Chile), also recognised early on the importance and value of relating ore mineralogy, geological characterisation and metallurgical behaviour."

Jan 1, 2016

By James E. Fisher, Roger Cotton

"The legal background f or environmental issues, and the growing emphasis both from government and private concerns of corporate and management liability for environmental problems provides one of the driving forces behind the growing concern with environmental law for the future. One prime objective must be the identification and minimization of potential liability, both for the corporation and its officers, directors and employees.This paper will identify the basis for liability of individuals and corporations for environmental matters, focussing on current legal requirements, and the appropriate legal response to events of such potential liability. It will also consider the reduction of liability through the implementation of management systems and environmental policies in order to ensure due diligence both with respect to corporate responsibility and the responsibility of the individuals within the corporation.IntroductionConsolidated Professor Mines Ltd . and its predecessor have been exploring in northwestern Ontario for about sixty years . During the last twenty years, the company has been interested in developing a gold mine, the Duport Project, on Stevens Island in Shoal Lake . The lake straddles the border between Ontario and Manitoba and is a drinking water supply for Winnipeg and environs.The Duport Project involves the mining of 450 t/day grading an average of 0.35 oz Ault of ore . At the minesite, located on Steven s Island in Shoal Lake, only preliminary processing of the ore will take place, to produce gravity and flotation concentrates for final gold recover y at a mainland plant well removed from the Shoal Lake watershed. No hazardous chemicals will be used at the island site."

Jan 1, 1991

By B. Jena, M. Rigaud, S. C. Panigrahy

"The influence of flux addition on the structure and properties of pellets produced from low silica specularite with peat moss and bentonite as binders was investigated. Specific pellets basicities in the range of 0.4 to 3.2 were obtained by the addition of limestone or a combination of dolomite and limestone as flux. A t basicities < 1.6, the bonding in the pellets was provided by a glassy silicate phase. At basicities =1.6, calcium ferrites were the predominant bonding phase. When dolomite was added as a flux, presence of magnesia-ferrite was noted. The reduction behaviour of pellets at different basicities was found to be influenced by the type of flux and binder. The pellet compression strength and swelling characteristics were improved with increased basicity.IntroductionThe properties of iron ore pellets are influenced by the type and nature of the ore or concentrate, additives and their subsequent treatment to produce pellets. The interaction between various constituents of the concentrate and additives, i.e. iron oxides, gangue and fluxes etc. result in the formation of various mineralogical phases which affect the degree and nature of bonding achieved in the pellet and the structure and distribution of pores. The pellet properties such as pellet strength and reducibility are influenced by the extent and type of bonding achieved between the ore particles. In view of the present emphasis on the production of high quality pellets to meet progressively stringent quality control requirements, it is essential to investigate the effect of additives on the bonding mechanism and properties of the pellets.In the past, the effects of additives on the bonding mechanism of pellets have been investigated. It is important to note that the conditions and parameters to be controlled are typical of a given concentrate/ore. In this paper, the results of the investigation on characterization of fluxed pellets produced from a low silica specularite concentrate are reported.This investigation was also aimed at assessing the suitability of peat moss for use as a binder for the production of low silica fluxed pellets. Peat moss is abundantly available in the vicinity of iron ore mines in Quebec and encouraging results have been obtained du ring the production of high silica acid and fluxed pellets."

Jan 1, 1992

By Barry W. Schmitke, J. M. Marino

"Cigar Lake Mining Corporation is presently operating an underground test mine in northern Saskatchewan, with a view to developing a high grade uranium deposit. The mining test is intended to demonstrate that the innovative mining methods designed are safe and economical. Two vertical mining methods are considered for the test:• box hole boring from the lower level;• blind boring from the upper level.In both cases, it is anticipated to freeze the ground before excavation to ensure hole stability and limit the inflow of water. Special care will be taken to minimize radiation exposure of personnel.Remote controlled equipment will be used where applicable.The access to the orebody was an important component of the test. After shaft sinking to a depth of 500 m, development work commenced at the 420 level in fractured sandstone which was grouted to restrict the inflow of formation water. The drifting continued in a section of poorly consolidated sand, clay and sandstone; this area was frozen to allow stabilization prior to excavation. At the 480 level relatively little water was encountered in the altered basement gneiss and grouting was not necessary; however, extensive ground support was required in the soft ground areas."

Jan 1, 1992

By Robert B. Parsons

"First down and four to go. In the game Of football, this is not a bad position to be in. However, in this game of political football, it means that there is still a long way to go. The government in Ottawa has concluded an important agreement with one producing province, and now has at least four more provinces to deal with-B. c., Saskatchewan, Nova Scotia and Newfoundland.On September 1, 1981, the federal and Alberta governments took a significant step forward in formulating an oil and gas policy for Alberta and the rest of Canada on signing a comprehensive five-year agreement that covers taxes, prices, incentives and other fiscal matters related to the production and marketing of oil and gas.This month, Tax Notes examines the main features of the agreement, and offers some eye-opening observations of what the new accord could mean for the future of the Canadian petroleum sector in particular and Canadian business in general."

Jan 1, 1981

"The last thirty years have seen enormous changes in all aspects of the gold industry, from the technologies of mining and extracting gold to the role it has played in the fiscal policies of nations. In this time, the market price of gold has increased ten fold and mine production has more than doubled. However, the cost of mining and extracting gold has also increased exponentially, and the industry has struggled with declining ore grades and increasingly refractory ore bodies.With the major economic powers of the world shrugging off the uncertainties of the post cold war era and moving into a period of unprecedented political stability, economic growth and low inflation, gold is also losing its lustre as a hedge against inflation and a backing for national currencies. Consequently, countries that had accumulated and hoarded gold for decades are now disposing of these non-performing assets, resulting in major swings in supply of the metal. Fortunately, this has coincided with the end of communism in many parts of the world and a tentative move to free market economies in most of the developing nations. As a result, people are becoming wealthier, and this is creating more demand for gold, principally in the form of jewelry.On balance, the shift in the role of gold, from one in which a significant portion of new gold production lay dormant in bank vaults as insurance against political or fiscal instability, to one in which most new gold is now freely traded as an industrial commodity, responding to normal market forces of supply and demand, has had a negative impact on the price of gold over the last fifteen years. In that time, the gold price has declined from a peak of $850/oz in 1980 to an average price of about $400 through the rest of the l 980's, to a price of -$320/oz today (1997). In large measure, this has been due to the enormous inventory of gold metal that was held by central government banks in vaults around the world, and which has been dumped on the market as soon as the price has started to trend upwards. Even today, after ten years of fairly steady selling by central banks, about 3 0, 000 tons of gold (or -8 years' supply at the present rate of consumption) is still retained in vaults (Murray et al., 1997).The downward pressure on the price of gold has created exciting opportunities for the development and implementation of new technology. Increasing the efficiency of gold recovery from more and more refractory ore bodies, whilst at the same time lowering production costs, have become critical to survival in this industry. These challenges have been met by the development and implementation of new technologies such as heap leaching, carbon in pulp, resin in pulp and the sulphide ore pre-treatment process of pressure leaching, bacterial leaching and fluid bed roasting. For an industry that saw very little technological change in the first seventy years of the twentieth century, the pace of change over the last thirty years must have seemed bewildering at times."

Jan 1, 1998

By V. Evans

Mine lateral development advance rates currently average about 5 metres (16.5 ft.) per day. Granduc Tunnel hit 35.1 metres (115 ft.) on their best day, 12 km from the portal, single heading forty-three years ago. This Canadian mining record remains an excellent example of rapid drill and blast excavation with suggestions for improving current practice.

May 1, 2011

By D. Kershaw

"A world-scale surface mining operation is associated with the Syncrude Oils ands Plant. Each day over 300 000tonnes of oils and are mined and transported to the process plant to produce 129 000 barrels of synthetic crude oil.Examples of research and maintenance engineering programs which have resulted in substantial gains in dragline and bucket wheel conveyor system productivities are discussed. Two central themes within these programs, which go beyond the usual technical support associated with a large surface mining operation, are pursued:1. the approach taken to determine the causes of component failures and provide Syncrude performance specifications to allow manufacturing industry to respond with more appropriate products; and2. systems and equipment studies which have led to higher productivity in the major mining equipment and the development of an auxiliary feed system.IntroductionA world-scale open pit mining operation is associated with the Syncrude Oils ands Plant located near Fort McMurray in northern Alberta. Over 300 000 tonnes per day of oils and are mined and transported to the process plant. Fifty million barrel s of synthetic crude oil were produced in 1987, which represents 10010 of Canada&apos;s crude oil requirement.following tree clearing and surface drainage, overburden is removed by mobile equipment ahead of oils and mining. Draglines excavate the 40 m depth of feed grad e oils and which is windrowed on the dragline bench. Bucketwheels reclaim the oils and from the windrows for transport by conveyor systems to the extraction plant surge pile.The Syncrude mine is operated in four essentially equal quadrants, each serviced by a dragline and a bucketwheel conveyor system. The mining face in each quadrant is approximately 2 km long and reclaimed oils and is transported by 1830 mm shift able conveyors over distances up to 6 km. Individual conveyors vary in length up to 2500 m.The Syncrude plant started operating in late 1978, and Figure I shows the mine production history through to the end o f 1987. Annual production volumes have increased from 50 million tonnes of oils and in 1979 to 105 million tonnes in 1987.The period from 1982has seen a change in operating philosophy, away from striving for very high production rates, to operating at sustained targetted levels within the measured capacity of the equipment. Higher over-all production volumes have resulted from being able to operate for more hours at these rates. This same period has also seen much greater emphasis placed on routine inspection of the equipment and planned preventive maintenance to avoid problems which could otherwise impact on production."

Jan 1, 1990

By A. C. Headon, K. W. Lam, D. P. Dautovich

"Microbiological activities affecting the performance of materials have been encountered in diverse situations within Ontario Hydro. Case histories of bacterial problems which are presented include ground rod corrosion at transformer stations, corrosion of a bare steel cooling water intake structure in Lake Huron and corrosion of steel components in a nuclear generation station vacuum building. Possible microbiological activities which may affect the corrosion behaviour of containers for the disposal of nuclear fuel waste in the future are discussed, as are bacterial actions suspected of causing an odour problem in residential water heaters.IntroductionBacteria are ubiquitous. Except by use of sterilization methods, bacteria -free environments are no t possible to find. Bacteria lie dormant in hostile environments, spread easily through air and water currents and reproduce rapidly under favourable conditions. Although different types of bacteria have different preferable conditions for growth, they are highly adaptive and in general, whenever there is a source of water and carbon (carbon dioxide or organic matter), there will be bacterial activities . These activities often induce or enhance costly metallic corrosion in industries and water odour problems in rural water supplies . Underground structures and systems in contact with natural water or water containing organic matter are most susceptible to bacterial attack.The types of metal-degrading bacteria , their characteristics and the conditions for growth have been reviewed extensively in the literature(1,2,3). There are several often encountered groups of bacteria which, through their metabolic processes, may lead to the degradation of metals. A large variety of bacteria produce corrosive in organic or organic acids as waste, such as the well known formation of sulphuric ac id by aerobic sulphur oxidizers . Anaerobic sulphate reducers produce hydrogen sulphide which is corrosive and has an obnoxious smell, slime-forming bacteria from slime which shelters sulphate reducers and iron bacteria oxidize ferrous to ferric ion which precipitates as hydrated oxides creating oxygen concentration cells . The following are bacterial problems encountered in Ontario Hydro. Although the number of recognized cases has been few, they show the diversity of location and environment where bacterial problems could arise. These include ground rod corrosion at transformer stations, corrosion of bare steel in a water intake structure, corrosion of steel in a nuclear generation station vacuum building and an odour problem in residential hot water tanks. In addition, possible bacterial- enhanced corrosion in containers for future disposal of nuclear fuel wastes are also discussed."

Jan 1, 1984

By G. H. Blackwell, A. J. Sinclair

"The main components of a ""PC” -based mineral inventory system are described in a sequence common to many real reserve/ resource estimation projects and in the practical context of problems and decision-making typically encountered in such studies. Some components are designed particuarly to improve the geostatistical instructional capability of the package. An important part of this approach involves the use of widely available software for data manipulation and evaluation in the design of a mineral inventory study progressing to mine design and feasibility. A variety of more or- less fixed routines written in high level languages provide acceptable computational speeds on a personal computer. These critical segments are linked by simple, short, compiled Basic programs easily adjustable to various data configurations and needs. IntroductionGeostatistical mineral inventory estimation has progressed greatly since its slow dissemination during the 1960s. The mining industry generally has accepted the benefits of the technique, notably the quantification of grade and geology, an indication of error in grade estimation, and of the mined volume / grade variance relationship (Clark, 1979, Isaacs and Srivastava, 1989).Acceptance has been slowed, first by complexities of geostatistical theory and second by a bewildering variety of computer systems and applications programs. Continuing improvements in education will facilitate a better understanding of the underlying theory.The purpose of this paper is to describe, in a practical context, the development of a geostatistical-based approach to reserve/resource estimation. The approach integrates various existing commercial software packages with a wide selection of programs developed by the authors for personal computers which estimate mineral inventories and educate users in the techniques applied; that is, the QMIN system.It is hoped that the approach presented here will convince mining and geological engineers concerned with resource estimation, of the soundness of geostatistical methods and its broad potential to their problems."

Jan 1, 1992

By Dallas W. Davis

"Since May 1980, New Brunswick has called separate tenders for the right to explore and develop several potash prospects, as well as areas underlain by Alberta oil shale. These tender calls had in common the provision for a basic ad-valorem royalty, combined with sharing of cash flow after exceeding a 15-20% discontinued cash flow rate-of-return threshold. In the case of potash, the bidding variable was a share of cash flow, but for oil shale it was exploration expenditures committed, with the cash flow sharing to be negotiated at the time of application for a production lease. The Millstream potash occurrence, previously discovered by government drilling, received five bids (21.1% highest), the Dorchester ""grassroots area"" with four surmised drill targets apparently received no bids, and in the case of oil shale there were only two bids on the one block previously subjected to the most exploration.It is concluded that New Brunswick will not be successful in awarding the potash or oil shale rights in return for a comparable level of basic royalty and cash flow share as in the case of Millstream, unless it spends money in discovering prospects or sharing the exploration risk with companies. The approach is likely to work for oil shales only if current exploration proves the existence of much high-quality material or a definite trend of real increases in the price of oil is again established. Undoubtedly, it continues to be desirable to assure an on-going stable investment climate through award of potash and oil shale rights under terms which provide for a return that the public and future governments will consider fair. This could mean that some form or risk sharing with companies would be advisable."

Jan 1, 1983

By Sukumar Bandopadhyay, Arunapuram Sundararajan

"For the last three decades, the application of network planning has provided a basis for a formal and general approach to the discipline of project management. For fixed activity duration, a very simple algorithm commonly known as critical path method (CPM), gives the length of time required for the total project as well as indicates the activities which are vital to the completion of a project. Project Evaluation Review Techniques (PER T) on the other hand, generalize the above approach to recognize uncertainty in the activity durations by allowing them to be random variables. One of the misleading aspects of current "" PER T"" solution method is, however, the implication that there is a unique critical path. In general, any number of paths could be critical, depending on the particular realization of the random activity durations that actually occur. In this case, simulation can be utilized to estimate completion time of a project.In this paper, the concept of criticality indexing is discussed, and a simulation model application which defines the critical path based on the criticality indexing concept, to a longwall development - extraction network, is presented. The model also provides suitable scheduling of resources based on the resource constraints and smooth s out period-t o-period assignments. IntroductionThe successful management of large-scale projects require careful planning, scheduling , and coordinating numerous interrelated activities. To aid in these task s, formal procedures based on the networks and network techniques (variously called PERT or CPM) were developed. In its original form the completion time for individual activities of a project was assumed fixed and known in advance: this in turn led to the familiar algorithms for computing the critical path, earliest start time, slack, and so forth. The unreality of such an assumption is, of course , apparent in many contexts. Consequently, attempts were made to introduce probalistic activity completion times, allowing representation of the stochastic nature of most projects."

Jan 1, 1987

By James L. Parks, David M. Kjos

"Significant increases in mill liner life and plant availability can be achieved by following guidelines that have evolved from over twenty years of practical experience with autogenous grinding (A0) and semi-autogenous grinding (SA0) mills. A0 and SA0 mill liner functions, performance criteria, designs, wear-resistant materials and maintenance procedures are reviewed. Operating practices that can lead to accelerated wear and breakage are discussed.IntroductionEfforts to improve the performance of liners for autogenous grinding (AG) and semi-autogenous grinding (SAG) mills began as soon as the modern, large-diameter versions of these comminution machines were first intalled in commercial plants twenty years ago . While concentrators with conventional circuits were typically running at 95010 or better mill availability, many of the new autogenous and semi-autogenous circuits were struggling to achieve 80% availability. Liner maintenance, which involves not only material and labour costs but also loss of production, was quickly identified as one of the major reasons for downtime.Today, liner designs and materials have evolved to the point where virtually maintenance-free liner life of two to three years is possible in autogenous mills and one year in the more severe operating conditions encountered in semi-autogenous mills. Of concern, however, is that hard-won lessons from the past sometimes seem to be forgotten or ignored during the design of new mills and the operation of existing mills. As liner suppliers, we are often confronted with performance problems that could have been avoided by applying well-publicized guidelines for liner design and materials selection.This paper provides an overview of AG and SAG mill liner functions, criteria for evaluating performance, designs, wear-resistant materials and maintenance procedures. Also, operating conditions that can lead to accelerated wear and liner breakage are discussed in detail."

Jan 1, 1990

By Roger D. Plouffe

In today&apos;s mining industry, it is possible to retrieve, from small-diameter holes, geophysical data for qualitative interpretation in exploration and quantitative interpretation in the development of orebodies. The primary objectives in the exploration stage are to identify where, within a hole, economic minerals are, and to help in lithological interpretations. Other aspects, which are more quantitative, are the interpretation of downhole logs for parameters which can be used in surface geophysical methods (i.e. density for gravity surveys, acoustic velocities for seismic surveys, and magnetic susceptibility for airborne and ground magnetic surveys). Recent advances in equipment design, portability and durability have made downhole logging in exploration more inexpensive and reliable. This new equipment is being used to generate very precise quantitative results. This is especially true on uranium development projects. The interpretation of gamma logs for eUJOS values has finally become precise enough that they have begun to replace chemical values in reserve calculations. Another part of development data is density and equilibrium information, which, with today&apos;s technology, is being derived from downhole probing. In the years to come, the trends for many metals are toward neutron activation techniques, or "in-situ assaying", and the use of multiple logs for better lithological and physical rock property determinations.

Jan 1, 1981

By D. Milne, P. Germain, G. Sauriol

"The practical determination of optimum stope geometry has, until recently, been an art relying primarily on experience at a given operation. Due to the complex and variable nature of rock masses in situ, stopes are often designed either very conservatively, resulting in excess development, or non-conservative resulting in excessive dilution and, in some cases, in loss of ore reserves.The Geomechanics group of the Mining Technology Division, Centre de Recherche Noranda, uses a combination numerical modelling and empirical design techniques to optimize allowable stope geometries. The above methodology allows the optim ization of stope geometry for varying rockmass classifications within an operation or between different operations. Such techniques require the development of a thorough geotechnical database at each operation and are best used when calibrated to the specific operation through back analysis.This paper discusses the above optimization techniques in light of specific examples from the Noranda Group. The design methods, limitations and results are discussed.INTRODUCTIONMine design has traditionally referred to production planning, general facility layout, (i.e. ore passes, crusher stations, main haulage drifts, etc.) and ventilation design. The dimensioning and sequencing of the stopes and pillars, however, has been almost solely based on trial and error and precedent practice.More recently, numerical stress analysis has received much more attention as part of the design process. It is common now at many operations to look at the effect of proposed stope layouts and sequences on stress redistribution through the surrounding mine workings. Through calibration of actual stope and pillar behaviour in situ, one can then relate the model predictions to support requirements, safety problems, etc."

Jan 1, 1989

? A BARGE WILL BE INSTALLED IN THE BOTTOM OF A COMPLETED PIT. ? THE PROVEN BAUER CUTTER TECHNOLOGY WILL BE INSTALLED ON THE BARGE AND A DEWATERING PLANT WILL BE INSTALLED NEAR THE BASE OF THE PIT RAMP. ? THE WATER LEVEL IN THE PIT WILL BE RAISED BY 20- 40 METRES AND REMAIN CONSTANT OVER DURATION OF MINING. ? THE CUTTER WILL BE LOWERED TO MINE 10 METRE DEEP BENCHES ON A CHECKERBOARD PATTERN TO AN ULTIMATE DEPTH OF 200 METRES. ? THE 5? MINUS CUTTINGS WILL BE PUMPED TO THE DEWATERING PLANT, DEWATERED, AND TRUCKED TO SURFACE.

May 1, 2003

By William M. Luff

This paper outlines the regional geology and history of the area, and summarizes the stratigraphy, structure and geology of the Brunswick No. 12 mine area. The Brunswick No. 12 deposit is a stratiform massive sulphide body. It occurs in rocks of the Tetagouche Group, which is believed to range in age from Lower to Middle Ordovician. The stratigraphic sequence, including the stratiform orebody, in ascending order consists of older metasedimentary rocks, augen schist, metasediments, augen. schist, footwall metasediments, the -massive sulphide body, iron formation, hanging-wall metasediments, siliceous tuff, basic volcanic rocks , basic iron formation and a porphyry dyke. This sequence is similar to that at some other deposits in the area. Four phases of structural deformation are known to be present in the Brunswick No. 12 mine area. The first deformation folds (F1 ) and associated faulting are the most important factors in determining the distribution of the massive sulphides. This deformation has resulted in the massive sulphides being separated into four zones: the Main Zone, the West Zone, the East Zone and the V-2 Zone. Brunswick Mining and Smelting Corporation Limited is actively mining, developing and exploring the deposit.

Jan 1, 1977