Search Documents

By Donald Leroux, Martin Suichies, Andy Trusiak, Chris Dechert

"In modem concentrators, the operation of flotation machines is often stabilized by simple control loops. Froth level, slurry density and aeration rate are all physical parameters typically controlled through classical PID loops. Few concentrators, however make use of advanced computing technologies for controlling the grade of flotation product streams. Technical challenges such as long process delay and the long and uneven sampling interval of on-stream XRF analyzers often restrain their implementation. Model Predictive Control (MPC) is known to have better performance than PID for controlling processes with long delays (such as flotation circuits). This paper describes the implementation of a multi-input/single-output (MISO) MPC algorithm and an FIR model identification routine using an object-oriented graphical computing environment.The MPC module (controller and identification) was implemented on an industrial control system and applied to many sulfide flotation circuits in the Brunswick Mining concentrator (New Brunswick, Canada). In most cases, the manipulated variable was the collector addition. As long as it is provided with decent process models, the performance of the MPC controller is good on all the flotation circuits on which it was applied. Significant reductions of grade variance are reported and the controller responds well to set-point changes. The user-friendly, graphical nature of the computing environment led to a high degree of acceptance by both the process engineers and the flotation operators.1. INTRODUCTIONOver the past three decades, much instrumentation has been developed for flotation machines. The introduction of instruments such as pulp density gauges and cell level probes was particularly well received by the plants where pneumatic and electronic controllers were available for implementing PID control loops. In a way, these simple loops revolutionized the mineral industry. The operation of flotation circuits could then be stabilized through the use of automatic controllers."

Jan 1, 1999

By Michael I. Brittan, Craig M. Sams

"Economies of scale and the variable characteristics of many large ore deposits have resulted in grinding installations using very large SAG mills fitted with variable speed drives. Low-aspectratio single-stage SAG mills were introduced in South Africa to process the consistent gold bearing Witwatersrand quartzites. Elsewhere, circuits were patterned after the more conventional North American circuits with high-aspect-ratio SAG mills followed by ball mills. This paper provides information on two recent Gold Fields group installations covering both types of SAG mill in large, single-stage applications. While these operations process similar tonnages, the mills represent opposite ends of the aspect-ratio spectrum. The Tarkwa mine in Ghana employs a low-aspect 27’ x 42’ 14MW SAG mill. The St Ives mine in Australia operates a conventional 36’ x 18’ 13.4MW SAG mill.INTRODUCTIONGold Fields is one of the world’s largest gold producers with annual production of approximately 4.2 million ounces. The Gold Fields group has operations in South Africa, Ghana and Australia, along with numerous exploration sites and advanced projects in several other countries. This paper discusses new milling operations in Ghana and Australia.TarkwaThe Tarkwa Gold Mine is located in Ghana, West Africa, approximately 350 kilometers west of the capital city of Accra (Figures 1 and 2). The site conditions are tropical with an average annual rainfall of 1,930 mm and a maximum temperature of around 35°C."

Jan 1, 2006

By Manuel Sanchez, Marcial Medina, Matt Hurley, Hugo Granados, Pramod Kumar, Raj Rajamani, Jose A. Delgadillo

"Large-diameter ball mills have traditionally used steel liners—steel being a highly durable material that can be shaped into any desired geometry, among which the double-wave has been the preferred design. Such a design produces a purely cascading charge motion, which is ideal for the shearing action needed to produce a finer product. Today, however, rubber liners, which have been in existence for over forty years, are now preferred over traditional steel, largely because they weigh less and are easier to maintain. In this paper, we show the operating data from the Hudbay Minerals’ Constancia Mine, wherein the liners on a 26-by-40-foot mill were changed from conventional steel liners to PolyStl™ liners. It is then shown that this change reduced the amount of energy consumed whilst being able to maintain previous grind and throughput levels. The design is verified via discrete element simulations.IntroductionThe Constancia Mine (“Our Business: Peru,” 2016) is located in the southeastern Andes of Peru, at an elevation of approximately 4,200 m. It can be accessed via the CU-126 road, about 95 km from the town of Espinar in Espinar Province. The mine also contains both the Constancia and Pampacancha deposits in the Province of Chumbivilcas. Hudbay Minerals, Inc. acquired the mine in 2011, through the purchase of Norsemont Mining, Inc. and currently retains sole ownership of the property. Production of the Constancia Mine began in 2014, with commercial production levels being achieved in April 2015.The Constancia and Pampacancha deposits primarily include hypogene, supergene, and skarn ores. The Mine’s main products, however, are copper concentrate, with silver contents, and molybdenum concentrate. These mineral reserves are expected to last approximately 22 years. Constancia’s open-pit mine supplies a processing plant that is designed for 81,900 metric tons per day of throughput. Average annual copper production is estimated to be 82,000 mT (contained metal in concentrate). Actual plant production can be found in Table 1."

Jan 1, 2017

By R. S. Simkus, J. R. Egan

"Changes have recently been applied to the Sullivan Concentrator lead and zinc circuits to treat fine-grained ores which make-up the majority of ore reserves in the mine. Pilot plant test work conducted in 1990-91 indicated that concentrate grades would be substantially improved by reducing the particle size (P,0) of the lead from 38 to 15 µm and the zinc from 45 to 24 µm.Circuit revisions involved installation of major new equipment including: two GUO kilowatt Vertimills for regrinding, a 4 metre diameter column flotation cell and a 4 metre diameter hyperbaric pressure filter for dewatering. Duties of the existing regrind mills were reassigned.IntroductionThe Sullivan ore body is a massive sulphide deposit consisting of fine grained mixtures of sulphides, sometimes inter-banded with country rock and varying widely in their content of lead, zinc, iron and silicates. Principal economic minerals are marmatite and galena. Iron is mainly present as pyrrhotite (85%), and to a lesser extent as pyrite (15%) .The orebody has been actively mined since 1923, with 1992 ore reserves estimated at 15,800,000 tonnes with an average grade of 4. 7% lead and 7. 9% zinc. Current plans call for treatment of 1,600,000 tonnes/year, (7,000 tonnes per operating day), with flotation feed grades of 5.9% lead, 10.1% zinc, and 22.0% iron."

Jan 1, 1994

By Charles Knilans, Tassos Grammatikopoulos, Nicole Hoffmann

"Twin Metals Minnesota LLC, (TMM) has recently completed a prefeasibility study evaluating the development and operation of an underground copper (Cu), nickel (Ni), platinum (Pt), palladium (Pd), and gold (Au) mining project on the Maturi deposit in northeastern Minnesota.The Maturi deposit is a magmatic Cu-Ni-sulphide deposit occurring along the basal contact of the South Kawishiwi intrusion, comprised of heterogeneous troctolites to gabbros forming a tabular body designated the BMZ (basal mineralized zone). These rocks provide the major gangue mineralogy (plagioclase, olivine, and clinopyroxene) with local, minor rock-forming orthopyroxene, biotite, magnetite, and ilmenite. Altered silicates exist within local fracture and/or alteration zones, which are commonly associated with minor faults in the regional area. The Maturi deposit is comprised of four main mineralized zones within the BMZ, referred to as Stage 1, Stage 2 (S2), Stage 3 (S3), and Upper Heterogeneous. Chalcopyrite, cubanite, pentlandite, and pyrrhotite are mainly hosted within the S2 and S3 units, with talnakhite frequently occurring within the S3 unit.A cross-discipline approach combining geology, geochemistry, metallurgy, QEMSCAN™ mineralogy, and mine planning has been implemented to develop a preliminary geometallurgical model and life of mine metallurgical performance forecast. This paper provides an overview of the methods that were used to develop the model and forecast, and discusses the advantages of such a model in project development and evaluation.INTRODUCTIONThe TMM Project proposes mining a copper-nickel-palladium-platinum-gold-silver (Cu-Ni-PGM) magmatic sulphide deposit situated in the Duluth Complex of northeastern Minnesota, USA. The prefeasibility study proposes a 45,000 million tonnes per day mine and concentrator facility to produce two saleable concentrates. The mine will access two separate deposits, Maturi and Maturi Southwest. Saleable concentrates are the final products of the sequential flotation plant where a high grade Cu concentrate is produced followed by a Ni concentrate."

Jan 1, 2015

By Rajiv Kalra, Ji Jiangang

"This paper reviews the following aspects of the world’s largest manufactured Grinding Mill’s in terms of diameter and power, along with the world’s biggest shop assembly and trial run of the mills delivered to Sino Iron Magnetite Project in Australia.1. An overview of the basic flow sheet of the Sino Iron (Magnetite) Project located in Australia2. An overview of in-house designed CITIC Heavy Industries 12.2 m (40ft) F x 11 m(36ft) LG – 28MW AG mills including FEA and major components3. In-house manufacturing at CITIC-HIC work in Luoyang China of all major components for 6 off Ø12.2 m(40ft) AG mills and 6 off Ø7.9 m(26ft) x 13.6 m(44.6ft) LG – 2 x 7.8 MW Ball Mills4. Major aspects of design and preparation of the biggest shop trial run of Ø7.9 m(26ft) x 13.6 m(44.6ft) LG Ball Mill witnessed by international EPCM’s and clients in July 2009.5. Major aspects of one piece assembly of 1300 tonne rotating element of the Ø12.2 m(40ft) x 11 m(36ft) LG AG Mill and Ø7.9 m F (26) x 13.6 m(44.6ft) LG Ball Mill at the port of the export China and transport to Australian Port and then to site.6. An insight to unique installation methods used for Ø12.2 m(40ft) and Ø7.9 m(26ft) rotating element lifting on the mill foundation in one piece assemblies.7. CITIC Heavy Industries present capability for in house design and manufacture of Grinding Mills up to Ø13.7 m (45 ft) with 35 MW Gearless drives and Ø12.2 m(40ft) with 2 x 10 MW Geared Mill drives"

Jan 1, 2012

By Bern Klein, Randy Blaskovich, Reem Roufail

"Morphology is a tool that is rarely used for mineral breakage mechanism evaluation. Ground particles are typically assessed for their size distribution. They are also visually analyzed using image analysis. However, image analysis is not a comprehensive evaluation of the particle surface texture. It evaluates particle’s size parameters such as area, diameter, and perimeter amongst other features. On the other hand, morphology analysis takes the particle assessment to another level of detail. Morphology analysis evaluates particles’ roundness, elongation and angularity that would indicate the degree of roughness of the particle. According to Roufail and Klein (2009), rougher surfaces are generated due to breakage along grain boundaries – intergranular breakage. Mill operation, particularly mill speed, dictates the dynamics in the mill. Stirred mills are known to break the particles via abrasion under standard operation. However, if the dynamics of the grinding media in the mill are changed, the particles could be more exposed to impact and compression loading that would lead to a different mode of breakage.In this paper, the effect of material properties and mill operating conditions on particle morphology will be studied. Hard non-sulfide versus soft sulfide minerals are compared, namely quartz and galena, respectively. Extreme mill speeds are tested covering the range of 1000 to 2000 rpm for a 4-litre Netzsch (ISA) mill. In addition to particle size distribution, micro-analysis is executed in the form of morphological analysis using a tested manual roughness point counting technique.INTRODUCTIONGrinding in general and stirred milling in particular are processes that are used to break particles to liberate metal-bearing minerals for further separation downstream. The energy required to achieve the target particle size versus maximum possible liberation has been studied intensively and it is usually the breaking point for the grinding system chosen in a process flowsheet. Operating conditions are dictated by the energy consumption. Becker et al. (2001) related different forms of energy such as input, specific, volume/mass specific energies to stress intensities and final product fineness. Other research studies focused on energy input in a stirred mill (Zheng, Harris and Somasundaran, 1996)."

Jan 1, 2011

By J. P. Van Cruyningen, M. J. Puro

"A 2400 acre extension to the existing Tailings Area is under development at Inco's Copper Cliff Milling operations.The new area is being developed in stages as production levels dictate thus minimizing immediate capital expenditures while permitting disposal operations to proceed as further site work progresses.The first stage of the new storage site will be fully operational by early 1987 and will include a 400 acre site specific to the storage of Pyrrhotite rejected from milling circuits. The Pyrrhotite site is located in the centre of the Tailings area and is designed for water cover throughout much of its projected life.The new development incorporates perimeter dams designed to operate with low phreatic levels for maximum structural stability. Acid seepage water is collected behind secondary impermeable dams for return to the Tailings Pond.Tailings are deposited by up-stream methods permitting segregation of coarse fractions for use in future lifts of the perimeter dams."

Jan 1, 1987

By M. H. B. Nasseri

Barre granite?s samples have been tested for fracture toughness under mode I along two different directions with respect to microstructural fabrics were investigated. 3D objects counter algorithm technique is applied on micro CT images to identify physical properties such as crack induced porosity, crack density, generated total surface area and contribution of individual mineral grains within the damaged zone.The result obtained justifies very well the fracture toughness anisotropy in Barre granite, and explains the difference in the structure of the damage zone evolving as a result of test crack interacting with pre-existing microstructural fabrics. The present study has potential application in the fields of rock mass stability, oil reservoir stimulation, rock fragmentation and damage in blasting and emplacement of dykes.

May 1, 2009

By Rajiv Kalra

This paper reviews the following aspects of the world?s largest manufactured Grinding Mill?s in terms of diameter and power, along with the world?s biggest shop assembly and trial run of the mills delivered to Sino Iron Magnetite Project in Australia. 1. An overview of the basic flow sheet of the Sino Iron (Magnetite) Project located in Australia 2. An overview of in-house designed CITIC Heavy Industries 12.2 m (40ft) F x 11 m(36ft) LG ? 28MW AG mills including FEA and major components 3. In-house manufacturing at CITIC-HIC work in Luoyang China of all major components for 6 off Ø12.2 m(40ft) AG mills and 6 off Ø7.9 m(26ft) x 13.6 m(44.6ft) LG-2 x 7.8 MW Ball Mills 4. Major aspects of design and preparation of the biggest shop trial run of Ø7.9 m(26ft) x 13.6 m(44.6ft) LG Ball Mill witnessed by international EPCM?s and clients in July 2009. 5. Major aspects of one piece assembly of 1300 tonne rotating element of the Ø12.2 m(40ft) x 11 m(36ft) LG AG Mill and Ø7.9 m F (26) x 13.6 m(44.6ft) LG Ball Mill at the port of the export China and transport to Australian Port and then to site. 6. An insight to unique installation methods used for Ø12.2 m(40ft) and Ø7.9 m(26ft) rotating element lifting on the mill foundation in one piece assemblies. 7. CITIC Heavy Industries present capability for in house design and manufacture of Grinding Mills up to Ø13.7 m (45 ft) with 35 MW Gearless drives and Ø12.2 m(40ft) with 2 x 10 MW Geared Mill drives

Jan 1, 2012

By Donald Leroux, Ralph Dahlke, Dave Scott, Finch. James A., Cesar O. Gomez

"The efficiency of the flotation process depends on how effectively air is dispersed into small bubbles. Bubble surface area flux - the surface area of bubbles per unit time per unit cross-section area of a cell - is emerging as the parameter to characterize gas dispersion. One of the approaches proposed to measure bubble surface area flux in industrial cells is based on the measurement of two variables: gas velocity and gas holdup, using separate sensors. Plant testing of the gas velocity sensor gave evidence of a series of operational problems which may be necessary to correct before attempting to characterize gas dispersion. Problems such as uneven air distribution within a cell and along a bank, faulty air and slurry valves detected during attempts to redistribute air, and poor control of pulp level and gas flow became evident. Detection of these problems from gas velocity measurements is illustrated.INTRODUCTIONBubble surface area flux is considered a key variable in the optimization of flotation circuit performance (Gorain et al., 1997; 1998). The Mineral Processing Group at McGill University has devised and developed a method for estimating bubble surface area flux in industrial flotation cells (Finch et al., 1999). The method is based on measuring gas holdup and superficial gas velocity using two separate sensors and applying drift flux analysis to estimate bubble size (Dobby et al., 1988; Banisi and Finch, 1994). With bubble size and superficial gas velocity known bubble surface area flux can be calculated.This method was selected by Noranda to characterize gas dispersion in cells as part of a program to model and optimize flotation circuit performance. However, initial testing at Brunswick Mine with the gas velocity sensor provided some unexpected results indicating operational problems and equipment malfunctions that needed to be addressed before systematic measurement of gas dispersion could be initiated.The subject of this communication is to illustrate the detection of these problems from gas velocity measurements. The line 3 Zn Cleaner circuit comprising four stages of Denver DR cells was the main subject of analysis, including the effect of correcting these problems on the metallurgical performance of the Zn 3rd cleaner bank of ten DRl 00 cells."

Jan 1, 2001

"The Key Lake mill was commissioned in 1983 to process the two Key Lake ore deposits. With the depletion of these ore bodies in 1999, the plant was converted to mill the exceptionally rich McArthur River deposit located seventy eight kilometers northeast of the Key Lake mine site. This paper describes in detail the Key Lake milling process. The mill consists of a grinding circuit, a leachkounter current decantation circuit, a solvent extraction circuit, a yellowcake precipitatiodcalciner circuit, an ammonium sulphate crystallization circuit, and a waste treatment circuit. The paper also describes process changes to handle McArthur River ore, including the ore receiving stationLOCATIONThe Key Lake mill is located 78 kilometres south of the McArthur River mine. It is located at latitude 57' N in northern Saskatchewan, within the southern boundary of the Athabasca formation. The nearest town is Pine House, located 240 kilometres to the south. Access to the mine is by an all weather road and by a private airstrip.HISTORYAND DESCRIPTION OF OPERATIONThe Key Lake mill was commissioned in October 1983 to process ore from the Gaertner and Deilmann ore bodies. The mill was designed to produce twelve million pounds of uranium oxide (U308) a year from a feed grade of 2.4% U3O8.Following grinding, the uranium is leached in a two stage leach circuit using oxygen and sulphuric acid. An eight-thickener counter current decantation (CCD) circuit is used to separate the uranium bearing solution from the solid waste residue. The uranium is further purified in a solvent extraction circuit and then precipitated using ammonia. It is then calcined at 840' Celsius, and packaged into drums for shipping to refineries. There is a crystallization circuit to recover ammonium sulphate produced in the process and a waste treatment circuit."

Jan 1, 2001

By E. Ghali, N. Sorour, G. Houlachi

"The binary Fe53Mo47 and ternary Fe54Mo30P16 coatings have been electrodeposited from citrate-based electrolyte on mild steel (MS) substrates. The electrodeposition has been conducted for 6 hours at 20 mA cm-2 and 30°C. The electrochemical tests were carried out in chlorate solutions containing 300 g L-1 NaCl and 4 g L-1 K2Cr2O7 at pH 6.4 and 80°C. A number of surface characterization techniques such as SEM-EDS, XRD and EMP were used to study the microstructure of the alloys. The electrocatalytic activity of these coatings was investigated using steady-state polarization and galvanostatic technique. This study revealed that the Fe-Mo-P coating could be considered as a promising cathode material for the hydrogen evolution reaction (HER). The results showed an important decrease of hydrogen overpotential for Fe-Mo-P alloy as compared to that of Fe-Mo and especially MS which is a traditional cathode in chlorate industry. The HER overpotential for Fe54Mo30P16 at current density of 250 mA cm-2 was decreased by 30% in comparison to that of MS (1029 mV), and by 16.5% to that of Fe53Mo47 coating (857 mV).INTRODUCTIONSodium chlorate is used for manufacturing of several daily consumption products. This chemical is mainly employed for the production of chlorine dioxide (ClO2) that is a bleaching agent used in the pulp and paper industry. The ClO2 is also consumed for generation of perchlorates, chlorites and other chlorates, as an herbicide and in uranium processing (Cornell, 2002). Sodium chlorate is produced industrially via following overall formula in un-divided electrochemical cell (Nylén & Cornell, 2009):"

Jan 1, 2016

"INTRODUCTIONGold tailings retreatment plants have been operated for many years throughout the world. Several large tailings retreatment facilities have been operated profitably in South Africa since 1976 and there are tailings retreatment operations in Canada currently in production with more in the feasibility stages.The Timmins Gold Tailings Project of ERG Resources Inc. was designed to treat 8,000,000 tonnes per annum of gold tailings for an eight month operating season, and commissioning of the operation began in July 1988. The payback period for this project is about 3 years which corresponds to an IRR of 30%.This report summarizes the metallurgical characteristics of the reclaim tailings, describes the process flowsheet which was developed to enable ERG to economically recover gold from the Timmins area tailings, and reviews commissioning activities."

Jan 1, 1989

By Wayne Phillips, Anatalia Silva, Robert Henderson, Tondo. Luis

"Kinross’ Paracatu Mine has 20 years of operational success as one of the lowest grade milloperated gold mines in the world. At year end 2005, Paracatu’s Proven and Probable Reserves were 1.18 billion tonnes at a grade of 0.40 g/t Au, containing a total of 15.2 million ounces of gold.In 2005, the plant processed 17 Mt of ore and produced 180,519 ounces of gold at a cash cost of US$274/oz. An investment of US$470 million has been approved to expand production to 61 Mtpa in 2009 which will extend mine life to 2036. During the period from 2009 to 2013 the project is expected to produce an average annual output of approximately 557,000 ounces of gold at an average cost of sales of approximately $230 per ounce.The soft, friable ore containing readily leachable gold associated with sulphides lends itself to simple processing. The process flowsheet consists of crushing, grinding, gravity recovery, flotation, concentrate leach and carbon adsorption to produce bullion bars. This paper describes the current operation, the deposit’s unique metallurgical features and the future expansion plant that has been designed to optimise recovery of gold.INTRODUCTIONRio Paracatu Mineração (RPM), a wholly owned subsidiary of Kinross Gold Corporation, operates the Paracatu mine. The mine is located in Brazil, 230 km south west of Brasilia in the north west portion of the State of Minas Gerais. The city of Paracatu, which has a population of 83,000 people, is just 2 km south of the mine."

Jan 1, 2007

By J. A. López-Molina, S. García, V. Castellanos-Pedroza

"Grouting aims to reduce the permeability of rock mass below a predetermined value and has been widely used in rock engineering field for a long time. However, the injection procedure needs several empirical decision makings and it is rather difficult to reliably confirm the achievement of improvement, because the grout penetration process is not sufficiently clarified. This investigation proposes a neuronal method of defining spatial distribution of rock hydraulic properties and a fuzzy scheme for estimating their relation with the grout penetration (consumption, localization and filling material). The intelligent method stands as a tool for helping in harmonizing the sealing activities and the medium conditions. The virtual simulation of grouting strategies embraces geology, hydraulic and rock characteristics and the filling process. Important aspects as different pressure injection levels and fracturing systems can be holistically studied using the intelligent environment, resulting in an advantageous, economic, flexible and interactive tool for planning better this critical activity.INTRODUCTION Grouting is a very common method of sealing rock and repairing concrete structures (Butron et al., 2010) and its use in engineering of dam-foundation and tunneling has been documented as very successful (Yang, 2004). Generally speaking, to achieve the closing purpose, boreholes are drilled into the rock mass and grout is injected (under pre-selected pressure) until the fractures around the borehole are filled. The complete filling of these fractures is possible if they are connected to each other in such a way that the remaining water and air can be displaced outside the designed grouting zone (Houlsby, 1990; Kutzner, 1996). Water testing is necessary for evaluating seepage potential and for determining whether grouting is necessary or practical. Regardless of the main reason for the investigations, design of a program for water testing for grouting should consider the type of structure to be built, the geologic conditions at the site and the level of seepage control desired. As information gathered the report must content the fracture openness, number and connectivity, exploratory drill holes orientations, materials situation and a panorama of rock-mass state (quality)."

Jan 1, 2015

By W. H. MacLean, S. Liaghat

Abstract- The Key Tuffite is a thick (0.3 m to 6 m) and laterally extensive (-10 km) cherty, sulfide-bearing tuff unit in Archean greenstones in the Matagami mining district in northwestern Quebec. It lies at the contact of the Watson Lake Group and overlying Wabassee Group volcanic rocks, and is host to major Zn-Cu volcanogenic massive sulfide deposits. The tuff component is highly altered and its volcanic precursors are not identifiable by petrographie means. The tuff is mixed with a volcanic exhalative component comprising chert, carbonate and sulfides (pyrite, pyrrhotite, and minor sphalerite and chalcopyrite). The normative mineral composition of the Key Tuffite is 33% quartz, 28% sulfides, 16% sericite, 8% carbonate, 60Jo chlorite and 9% other minerals. In the vicinity of the Bell Allard and Orchan mines, the precursor tuff components are identified using immobile major and trace elements, as Watson Lake tholeiitic rhyolite (Zr/Y = 1.5 to 3.5, LaN/Ybn. = 1.7 to 2.8, Si02 = 72.5 ± 1.2 wt %, and Wabassee calc-alkaline andesite (Zr/Y =9, LaN/Ybn. = 4 to 8, Si02 = 56% to 65%). Immobile element computation techniques were used to calculate mass additions and losses in the conversion of the tuff to the Key Tuffite. Average net amounts of Fep3 (27% total iron), Si02 (14%), CaO (8%), S and K20 ( + 2%), were added, Na2O was removed (-2.8%), and MgO was over-all unchanged. Total net mass change was +63%, which comprises mainly exhalative additions, but also includes changes owing to hydrothermal alteration of the tuff component.

Jan 1, 1992

By W. H. MacLean, S. Liaghat

The Key Tuffite is a thick (0.3 m to 6 m) and laterally extensive (-10 km) cherty, sulfide-bearing tuff unit in Archean greenstones in the Matagami mining district in northwestern Quebec. It lies at the contact of the Watson Lake Group and overlying Wabassee Group volcanic rocks, and is host to major Zn-Cu volcanogenic massive sulfide deposits. The tuff component is highly altered and its volcanic precursors are not identifiable by petrographic means. The tuff is mixed with a volcanic exhalative component comprising chert, carbonate and sulfides (pyrite, pyrrhotite, and minor sphalerite and chalcopyrite). The normative mineral composition of the Key Tuffite is 33% quartz, 28% sulfides, 16% sericite, 8070 carbonate, 6% chlorite and 9% other minerals. In the vicinity of the Bell Allard and Orchan mines, the precursor tuff components are identified using immobile major and trace elements, as Watson Lake tholeiitic rhyolite (Zr/Y = 1.5 to 3.5, LaN/ybN = 1.7 to 2.8, SiO2 = 72.5 ± 1.2 wt %, and Wabassee calc-alkaline andesite (Zr/Y = 9, LaN/YbN= 4 to 8, SiO2 = 56% to 65%). Immobile element computation techniques were used to calculate mass additions and losses in the conversion of the tuff to the Key Tuffite. Average net amounts of FeP3 (27% total iron), Si02 (14%), Cao (8%), S and K2 (+ 2%), were added, Nap was removed (-2.8%), and MgO was over-all unchanged. Total net mass change was +63%, which comprises mainly exhalative additions, but also includes changes owing to hydrothermal alteration of the tuff component.

Jan 1, 1992

By B. Lueger, D. Shen, M. Sedighy, R. Rand, R. Saleh, J. Cheung, M. Rifai, I. Khan, W. Sauri, D. Setianto

The world’s first active power demand stabilization system for a 3-electrode electric arc smelting furnace was commissioned at PT Vale Indonesia in December 2012 on Furnace No. 2 using an SPLC (Smart Predictive Line Controller). The SPLC technology in combination with the Furnace No. 2 rebuild and other upgrades has enabled PT Vale to increase the electrical input to the furnace by up to 20% on a stable and sustainable basis by eliminating peak powers that overload and trip out the electrical equipment, and by reducing power unbalances. The SPLC technology maintains smooth arc power using a continuously variable thyristor controlled series reactor. The SPLC compensates variations in the furnace arc with predictive changes in the circuit reactance at a speed of up to 60 times a second. The system started up quickly and has been shown to be easy to operate and maintain by PT Vale. PT Vale’s Operations Team has been testing the new system at set points of up to 90 MW on the newly re-built Furnace No. 2. Over the last 12 months, the throughput of Line 2 has increased by approximately 10% on an annual average; however, debottlenecking in other design areas of the operation is required in order to achieve 90MW operation on a sustainable basis. This outstanding success results from a combination of the furnace and other upgrades, the SPLC active power stabilization, and the skill of PT Vale in quickly adopting new technologies and maximizing the combined benefits of each technology in their operation.

Jan 1, 2014

By A. Pratt

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

May 1, 2010