Search Documents

By H. Warren Newcomen, Dennis C. Martin

"This paper describes the investigation of a large, progressive slope failure on the southeast wall of the east pit at Highmont Mine, British Columbia Geotechnical investigation s consisted of geological and structural mapping, assessment of blasthole drilling records, review of rock core information, slope movement monitoring and back analysis of various possible failure modes. Climate records and mining history were also assessed to determine their relationship to slope movement.Analysis of movement monitoring records and geotechnical information indicates that the failure is deep seated. The upper portion of the failure surf ace occurs along clay filled discontinuities. The lower portion of the failure surf ace appears to occur through the highly altered rock mass. High groundwater pressures and mining at the toe of the slope are documented to have had a major influence on stability at various times during the failure. Stability analyses results are presented and possible remedial measures are discussed.IntroductionHighmont Mine is located near Logan Lake in the Highland Valley approximately 50 km southwest of Karnloops, British Columbia (Fig. I). Mining of the porphyry copper and molydenum ore bodies began in 1980. In May, 1983, when mining in the east pit had progressed to a depth of about 60 m (200 feet) , a failure (designated the Southeast Failure) began to develop in the southeast corner of the east pit. Subsequent mining to a depth of 110m (360 feet) was accompanied by frequent and substantial slope movements involving between 500000 and I 000 000 m3 of rock . The slope was monitored extensively to assess short-term movement trends for operational safety. Geological mapping, core logging and rock mechanics testing were used in conjunction with the long-term monitoring information to determine the failure mechanism, conduct stability analyses, assess the effects of instability on pit design and enable design and installation of remedial measures."

Jan 1, 1988

By R. Mulligan

"The Cordilleran tin belt extends from the Seward Peninsula in westernmost Alaska to Mexico. Throughout the Canadian section, tin occurrences are mainly confined to a belt along the northeastern fringe of the Western Cordilleran sub-region; the boundary of this sub-region with the Eastern Cordilleran sub-region is most simply defined as the practical eastern limit of granitic and metamorphic rocks. The stratified rocks underlying this restricted belt are mainly late Precambrian and early Paleozoic miogeosynclinal sedimentary rocks, which are more or less metamorphosed but otherwise are generally equivalent to the less severely deformed rocks underlying the Eastern Cordilleran sub-region. They contrast with Late Paleozoic - Mesozoic eugeosynclinal volcanic-sedimentary assemblages farther west, but the granitic intrusions throughout are mainly of Late Mesozoic age. Thus, narrowly defined, the tin belt largely coincides with a lead-zinc-silver metallogenic province, whereas copper deposits characterize the eugeosynclinal regions to the west. In addition to the tin occurrences, which include the Sullivan lead-zinc-silver mine, Canada's only significant producer, the belt contains all the beryllium, most of the tungsten and many Iithophile-type molybdenum occurrences. Several types of occurrences of each metal are represented. Lithium occurrences in the Canadian Cordillera are notably rare, and these few are insignificant."

Jan 1, 1971

By Victor F. Hollister

Elemental sulphur occurs as aformational sedimentary deposit in Upper Devonian Wabamun evaporites near Coronation, Alberta. The deposit developed in a stratigraphic jacies-change lrap; it is assumed that petroleum reacted with anhydrite to form sulphur, calcite, hydrogen sulphide and other reaction products. The deposit contains about 362,800 tonnes of sulphur and lies at a depth of 1200 m. The Coronation deposit is expected to be geologically typical of such other native sulphur deposits as may be found in Wabamun Group sediments. Widespread sour gas sulphur production f rom the Wabamun suggests the possibility that additional native sulphur deposits will ·be found.

Jan 1, 1984

By Sunil S. Gandhi

"The Mountain Lake deposit is a tabular sandstone-type uranium deposit, hosted by the basal unit of Middle Proterozoic Dismal Lakes Group. Uranium occurs mainly as sooty pitchblende disseminated in stratiform lenses within gently dipping quartzose sandstone. It is associated with copper sulphides, pyrite, hematite, and traces of nickel and cobalt arsenides and of silver.Exploration HistoryUranium showings on the PEC claim group were discovered during 1969 by an airborne radiometric survey carried out over the Dismal Lakes-Great Bear Lake area by Aquitaine of Canada Limited (Bizard and Salat, 1969). Some drilling was done in the vicinity of the showings in 1975 by the company under a joint venture with Eldorado Nuclear Limited but the results were not encouraging (Hassard and Woollett, 1975). During 1972, Trigg, Woollett and Associates Limited conducting surveys for Imperial Oil Limited, discovered numerous high-grade radioactive boulders scattered over a distance of several kilometres north and west of the showings, and the area north of the PEC claims was staked as the YUK claims (Ahuja, 1974). A systematic study of the boulder distribution and Pleistocene geology suggested a source additional to the showings. More intensive exploration followed, and in 1976 drilling just north of the PEC claim group boundary intersected the main deposit at a depth of 75 m to 150 m, beneath overburden up to 60 m thick. Part of the deposit extends into the PEC claim group which is under exploration by the Aquitaine-Cominco Joint Venture.The following brief description is based on the presentations in 1978 by F. Hassard of Trigg, Woollett and Associates Limited at the Geoscience Forum in Yellowknife, and by S.S. Gandhi of the Geological Survey of Canada at the Mineralogical Association of Canada Uranium Short Course in Toronto."

Jan 1, 1986

By J. P. Wiser

THIS paper discusses testing and quality control of milled asbestos fibre. It has been composed with the intention of: (I) Summarizing past, present and probable future methods of testing and classifying the various grades of commercial asbestos produced by the Quebec asbestos industry. (2) Acquainting those unfamiliar with the methods used for evaluating, testing and controlling the grading and the quality of Quebec chrysotile asbestos fibres with some of the physical and chemical procedures currently used for that purpose. (3) Discussing some of the complications facing the producers, such as variations in the orebody and special requirements of asbestos manufacturers. ( 4) Detailing some of the present quality control methods. SUMMARY OF PAST, PRESENT AND PROBABLE FUTURE TESTING METHODS Past During the first years of production of commercial asbestos in the Province of Quebec, fibre testing and quality control were based principally on dry screen analysis and visual inspection. These methods were gradually expanded during the period from 18, 90 to 1932. In 1932, standardization

Jan 1, 1962

By W. E. Roscoe

"Mineral exploration properties are those on which an economically viable mineral deposit has not yet been discovered. Such properties are bought, sold, optioned and joint ventured on the basis of their perceived potential for the existence and discovery of a viable mineral deposit. The intrinsic value of an exploration property is therefore based on the exploration potential. One measure of the exploration potential is the amount that can be justified to spend on exploration for a viable deposit.The appraised value method uses a cost approach to value exploration properties. It is based on the premise that an exploration property is worth the meaningful past exploration expenditures plus warranted future costs to test remaining exploration potential. Results of past exploration work are analyzed in order to retain only those past expenditures that are productive in terms of identifying remaining potential. Warranted future costs comprise a reasonable exploration budget to test that potential."

Jan 1, 2002

By Tim C. Webb

For almost 350 years, industrial rocks and minerals have been produced, used locally and exported from New Brunswick to markets throughout the world. Up until the early 1960s, commodities like grindstone, building stone, gypsum, and limestone served as the foundation of the province's non-fuel mining industry. The importance and high level of activity surrounding industrial rock and mineral development in New Brunswick is reflected in a multimillion dollar industry generating substantial revenue and providing a valuable service to its people. New Brunswick's varied geology is reflected not only by the diversity of industrial rock and mineral resources presently under development but also in several promising exploration and potential development opportunities. The province also hosts several industrial rock and mineral processing facilities, each with established technologies ensuring high-quality products and each with sufficient flexibility to supply customized products for various specialized niche markets. With the imminent availability of natural gas to parts of the province, the prospects for additional value-added processing and re-examination of known, yet presently undeveloped deposits, appear excellent. These variables coupled with the province's advantageous geographical location, highlighting tidewater access to global markets and within one day's trucking distance to a regional market of several million people, guarantee prompt delivery of high-quality products at competitive prices.

Jan 1, 2001

By G. Morin, F. Chiesa, B. Tougas, B. Duchesne, Jocelyn Baril, N. Giguère

"An aluminum A356 compressor impeller was sand cast using the Low Pressure technique. The casting was limited in size (170 mm in diameter, 1.2 kg in weight) and very intricate in shape thus making 3D mold printing particularly favorable; indeed, producing this part by the traditional pattern-core box route would involve mounting 12 cores inside the mold while stringent dimensional tolerances are required as the impeller blades are only 2 mm thick. Consequently the molds were produce on the X-One MFlex printer of Quebec Metallurgy Center - CMQ. A dozen castings were produced with different casting temperatures and filling times so that it was possible to assess under which conditions complete filling of the mold cavity would be achieved. Filling and solidification modeling allowed predicting misruns and metallurgical properties inside the A356 (AlSi7Mg04) casting.INTRODUCTION Recent advancements in additive manufacturing enable foundries to produce molds without the tooling (pattern and core boxes) necessary when conventional technology is used (Eyad, 2016). This is particularly advantageous when dealing with intricate shapes and/or when a limited number of parts must be produced within a few days rather than in 5 weeks. An additional advantage is gained when producing prototypes (Johnson, 2016) as changes are much less costly and time consuming when made on a numerical 3D drawing rather than on patterns and core boxes. 3D printing is normally economical for a small number of parts; however, if the part is not too big and very intricate in shape such as the part that will be studied in the present work, 3D printing can be economical even for an important number of castings to be produced. On the other hand, low pressure casting is a high integrity casting process in which the mold cavity is filled from the bottom via a transfer tube in which the liquid aluminum rises under the pressure applied at the surface of the melt as illustrated in Figure 1. The filling can thus be precisely controlled, eliminating the turbulence created when the mold is filled from the top (gravity casting). Also, the pressure applied on the melt during solidification results in excellent feeding of the casting when conditions of directional solidification are met. In the present work, the compressor impeller shown in Figure 2 will be sand cast by low pressure."

Jan 1, 2018

By H. P. Pew

THE Pembina oil field is in west-central Alberta, about 88 miles west-southwest of Edmonton. The field, about 35 miles long by T HE Pembina oil field is in west-central Alberta, about 88 miles west-southwest of Edmonton. The field, about 35 miles long by 85 miles wide, is the largest in Canada in areal extent, in the amount of oil in place and in the current producing rate. The discovery well was completed in the middle of 1953. The field has grown until its present area is 369,820 acres. There are 74 working interest owners in the field. Early in the producing history of the Pembina field a committee of operators was formed on a permanent basis. The Pembina Operators' Committee has established a permanent staff, which compiles and distributes pertinent field information on a regular basis to all participants. The Alberta Oil and Gas Conservation Board has dealt with field-wide problems primarily through this committee. Expansion of the field was rapid as shown by the number of wells completed -from 135

Jan 1, 1961

By H. Wotruba, J. Heizmann

"The use of shotcrete is a mandatory means for rock support and therefore for safety in many underground mining operations. If shotcrete gets into the flotation feed though, it can negatively influence the flotation process. This especially occurs when sublevel stoping, cut-and-fill or room-and-pillar methods are applied because as the mining face moves on, formerly applied shotcrete layers are mined together with the ore.As shotcrete does not differ significantly from fluorspar ore in its physical properties it gets moved through the comminution process and is fed to the flotation plant like the ore. To prove the influence of shotcrete on the flotation process, a laboratory test series was conducted at the Unit of Mineral Processing (AMR) of the RWTH Aachen University. The shotcrete grade of the flotation feed was varied between 0 and 10% through addition of pure shotcrete. Flotation parameters and also reagent dosage were held constant apart from the addition of the pH regulator, which was dosed to reach a constant pH of 8 at the flotation start. Results showed that with increasing shotcrete grades in the flotation feed the fluorspar recovery as well as general mass recovery decreased. The enrichment factor of Fluorspar also decreased with increasing shotcrete grades in the feed.In an effort to eliminate the shotcrete contamination of the flotation feed, a feasibility study for use of sensor-based sorting prior to the comminution process was conducted. Rock sorting not only reduces the bad influence of shotcrete on the flotation process, but also reduces comminution costs. INTRODUCTIONShotcrete is used in underground mining on a regular basis. It is used for rock support and therefore to increase safety in the underground mining environment. In mineral processing the presence of shotcrete can cause difficulties for example in the concentration processes. In flotation the highly sensitive reagent mixtures can be disturbed by the chemical activity of shotcrete and therefore recovery rates and selectivity of the process can suffer.Shotcrete is a special form of concrete which is applied pneumatically with high velocities and is compressed by its impact energy. Since the process is especially suitable for work in difficult environments and overhead areas, it is established in underground mining for many years. Shotcrete is not only applied in pre-processing of the mines, but particularly of use for cut and fill, as well as room and pillar mining methods. There it is used to secure excavation chambers. When the mine face is secured with shotcrete and subsequently the mining continues, the applied shotcrete will automatically be mixed with the ore."

Jan 1, 2016

By V. Gangrade

Recirculation is the major concern associated with the utilization of booster fans. In controlled recirculation, a portion of the return air is purposely mixed with the intake air and the mixture is directed towards a working district, while the air quantity and gas concentrations in the air are closely monitored and managed. The objectives of this study were to determine the gas concentration in intake and return airways during controlled recirculation, and to determine the recirculation fraction for multiple headings. Experiments were conducted in a laboratory model to determine the effect of controlled recirculation on the quality of air circulated through the working faces. Preliminary results showed that recirculation is beneficial to ventilation planning because it reduces the build-up of air contaminants at the working faces and reduces the overall power consumptions. The experimental results were used to quantify the recirculation fraction and to calibrate ventilation models of the laboratory model. These models are used to simulate the controlled recirculation and to predict the gas concentrations in multiple headings.

Aug 1, 2013

By Unknown

Diesel locomotives for underground haulage have been used in coal mines in Continental Europe for twenty-five years or more. In Great Britain, it was not until 1935 that permission was granted to use them in gassy coal mines, but since that time they have been employed in increasing numbers both in gassy and non-gassy coal mines and in metal mines. Their use underground in coal mines in the United States is still prohibited and the same was the case in Canada until 1946, when permission was granted to operate a Diesel underground in the Adanac mine of West Canadian Collieries, Limited, at Bellevue, Alberta. The locomotive used here is a 50 h.p. Hunslet Mark II. More recently, a 100 h.p. Diesel was placed in operation for underground haulage at No. 18 Colliery of the Dominion Steel and Coal Corporation, in the Sydney coalfield, N. S. Thus, on this continent, Canada has been a pioneer in the use of these locomotives underground in coal mines and there is no doubt that more and more of them will be employed as time goes on. We feel, therefore, that the following notes concerning their design and performance, which we have received from the High Commissioner for the United Kingdom, will be of interest to our members.

Jan 1, 1949

By Jack Young

U. S. Steel Canada Inc.’s Lake Erie Works is the last green field integrated plant to be built in North America. The plant was designed using the best available environmental technology to develop an environmentally friendly production facility. A summary of the technology and measures used in the construction of the plant are summarized in this paper.

Jan 1, 2015

By A. Sutherland Brown, Stuart S. Holfand

"The Northeastern part of the Cariboo district lies in the big bend of the Fraser River between Quesnel and McBride. The area shown on Figure 1 extends from just west of Wells to Isaac Lake, about 30 miles across the regional strike of beds.Topographically the area extends from the moderately well dissected Interior Plateau in the west through a transition zone to the fully dissected Cariboo Mountains in the east.The area is an important source of lode and placer gold. The Cariboo Gold Quartz and Island Mountain lode-gold mines have produced more than 32 million dollars in bullion since 1932. Placer-mining has probably produced an equivalent or greater amount, although only 15 million dollars is officially recorded because accurate statistics. were not kept until fourteen years after the origiiaal gold rush of 1860.The regional structure of the Barkerville district was summarized by Lang in the Jubilee Volume (1948, pp. 141-149). Since then a large amount of detailed and areal mapping by the writers has expanded the information available and made necessary a complete revision of the regional geology. Much of the information summarized in this paper, together with a full discussion of the revisions, may be found in British Columbia Department of Mines Bulletins, Nos. 34 and 38, but other information is as yet un-published.Rocks of the Kaza group are exposed in the core of the Lanezi anti-clinorium between Spectacle and Isaac Lakes. The main part of the group is composed of greenish micaceous greywacke and greenish schist with knots of garnet, biotite, or both, and minor amounts of pebble conglomerate. The upper 1,000 feet is composed of white to brown quartzites and brown phyllites. Altogether, about 6,000 feet of the group is exposed. 1t is of latest Precambrian, i. e. Windermere, age."

Jan 1, 1949

By Andrew Abraham

Continual improvement is the key to success in today?s competitive global arena. You require tools that promote dynamic quality management, deliver cost savings to your bottom line and provide the foundation for process improvement. ISO 9000 and ISO 14001 management systems and OHSAS 18001 are those tools. Since their inception, the benefits of ISO management systems and registration have been touted as the way to achieve better bottom line results. This spurred many companies to embark upon the road to registration with high expectations. The potential benefits of ISO management system implementation and third party registration that are commonly provided by Registrars and consultants are compelling adverts for success. ISO 9001:2000 is promoted as an essential tool for systematic efficient and affective management controls that provide a framework for analyzing errors and improving a company?s internal operational processes. It also allows companies to comply with internal and external customer and regulatory requirements thus continually improving the quality of their products and services and thus enhancing customer satisfaction. This, in turn, leads to greater customer recognition and increased market share. ISO 14001 implementation and registration may assist your company in reducing its litigation risk, raw material and energy consumption, waste disposal costs and possibly non tariff trade barriers. It should also provide continuity of operations, enhanced operational efficiency and consequently a competitive advantage in the market place. Registration of your ISO 14001 management system should also improve your company?s profile and credibility leading to regulatory flexibility and improved community goodwill. All of this will be a catalyst for improved morale and pride by employees and management alike. Likewise, OHSAS 18001, the latest certification specification for Occupational Health and Safety Management Systems supports Occupational Health and Safety legal and regulatory obligations and compliance, manages & controls Occupational Health and Safety risks and improves performance, safety culture and efficiency. OHSAS 18001 is an audit certification, and not a legislative requirement. Suggested benefits of implementation include reduction in accidents, lost time and associated liability and insurance costs and improving reputation and credibility through demonstrated commitment to health and safety. The foregoing increases access to new customers, joint venture partners and financing The skeptics say these are motherhood statements and lack corroborative evidence, i.e., ?Show me the money!?

May 1, 2003

By N. Aydogan, H. Dundar, Å. Partapuoli, A. Fredriksson, P. Wikström, K. Tano, G. Adolfsson

The Autogenous milling of ores holds an increasing attraction as the focus moves towards reducing energy usage, both direct and embodied in grinding media. However, most of the early AG mills were converted to SAG for improved stability and increased throughput. This imposes a huge penalty in steel grinding media consumption. The LKAB iron ore operations in Sweden process highgrade magnetite through fully-autogenous milling lines to a final product P80 of about 45µm. The outcomes of P9O AMIRA research surveys, covering a wide range of mill fillings and throughputs and with different feed blends, are presented. Insights are provided on operational strategies, opportunities, the influence of feed size control and balancing the blend of competent gangue and softer magnetite. Areas of importance in the successful operation and control of energy-efficient autogenous circuits are highlighted.

Jan 1, 2012

By G. E. Agar, R. Stratton-Crawley

"The applicability of a hydrocyclone model to simulation of the cyclone banks in a multi-stage sandplant circuit producing mine back fill has been demonstrated. The model ha~; been used in conjunction with a modular computer program for circuit simulation in order to study the effect of changes in the operating conditions. It has been shown that weight recovery to sand fill increases as feed percent solids decreases, and, to a lesser extent as pressure drop across the banks increases. An increase in apex diameter also causes an increase in weight recovery. Increased weight recovery must, however, be balanced against sump an1l cyclone capacity and dilution of sand fill by fines. The predicted results from circuit simulation were in good agreement with plant data.The model has been found to be applicable to widely different ores."

Jan 1, 1979

By M. Behrouz

Thermal power plants convert thermal energy due to nuclear reactions or the combustion of coal, gas, heavy oil, or some other hydrocarbon to electrical energy. They consist of a variety of equipment, such as boilers, turbines, generators, cooling towers, and auxiliary equipment. Any factor that affects the equipment efficiency affects the overall efficiency. Analysis of the cooling tower and raw water using the Langlier Saturation and Ryznar Stability Indices showed that the cooling water at Sarchesmeh was slightly scaling with respect to silica. Cold lime softening was found to be a cost-effective method to produce cooling water with adequate properties to reduce the cooling water make up from 85 to 70 m3/h and blow down rate from 35 to 20 m3/h.

Jan 1, 2007

By Robert F. Shurtz

This paper discusses and compares methods of statistical analysis of the information relating to the evaluation of an asbestos deposit. From a study of 10-ft. lengths of drill core, the separate effects of visual evaluation errors were determined, as well as the deviations between evaluators and the deviations produced by a slight displacement in the center lines of the check drill holes. The importance of careful statistical analysis of such information is stressed.

Jan 1, 1966

By A. Darragh

"Past Growth The Canadian coal industry has grown rapidly during the past two decades. Coal production increased over four-fold between 1965 and 1982; consumption almost doubled, imports remained relatively flat, exports soared and total demand increased nearly two and a half times. Coal production grew during this period at an average rate of 8.60/o, compounded annually; this remarkable performance is shown in Table 1 and Figure 1. The relationship between production and consumption is shown in Figure 1, where in 1981 the total Canadian production of coal for the first time exceeded total Canadian consumption. ln Figure 2, the relationship between imports from the United States and Canadian coal exports is shown; in_ 1981 again for the first time, exports offshore exceeded imports into Canada. The rapid growth in Canadian coal use between 1965 and 1982 followed a major decline after World War II, as the country moved rapidly to an oil based economy. Changes in consumption patterns between 1945 and 1982 are shown ~n Table 2. Railway consumption of coal was reduced to zero m the early 1960s. The industrial and domestic consumers market share fell from about 660/o in 1960 to 6.70/o in 1975; this share, however, appears to have stabilized in recent years and actual volumes can be expected to increase in the future. The steel industry's share of the coal market fell over the same period, but the volume in recent years has remained fairly constant at about seven megatonnes per year.Perhaps the most significant change in consumption is in the share of coal consumed in the generation of electricity; this has increased from 80/o in 1960 to over three quarters of the total Canadian coal consumed in 1982. This increase in thermal coal consumption has been supplied by indigenous coal, and was accompanied by a decreasing share for coal imported from the U.S.A. into central Canada. It is expected, because of the nuclear power commitment in Ontario, that this share will continue to decrease, although the total volume of coal imported may increase slowly over time. This will likely also have a dampening effect on future coal sales to Ontario from western Canada."

Jan 1, 1985