Search Documents

By A. M. Bell

General Summary THIS paper attempts to describe in a preliminary and general manner the nature of certain copper discoveries now being developed by Gaspe Copper Mines, Limited, in Holland township, in the interior of the Gaspe peninsula. Some copper mineralization appears to have been known here at the time of the earliest French explorations, was rediscovered in 1921, and has been under intermittent development by Noranda Mines since 1938. In the last two years discoveries have enhanced the picture so that the deposit now promises to develop into one of the important Canadian copper producers. As ideas are constantly changing with continuing development, any picture given now is very partial and tentative and must be subject to future revision. The nature of these copper occurrences differs from others known in eastern America. In many respects they have unique features but they are most closely akin to some copper deposits found away from the intrusive rocks in the porphyry copper districts of the western United States. The most important orebodies are replacement deposits in a limestone horizon in which the ore gangue is converted to skarn. These lie at considerable distances from any known intrusive but seem to have been derived from a buried stock of granite that intrudes the sedimentary rocks of Lower Devonian age. This intrusive has produced alteration effects in the overlying rocks that may afford a key to locating other ore areas in the Peninsula.

Jan 1, 1951

By W. R. Smith

Introduction No commercial deposits of silica sand are known to occur in British Columbia, so all requirements for foundry and other uses must be imported. During the war, nearly 5,000 tons per year were used, all originating in Illinois and delivered to local consumers for about $12.00 per ton. Present requirements are somewhat less, but the cost is still of the same order. The relatively high cost of silica sand in British Columbia is not only a serious item for present consumers, but might be a deterrent to the establishment of a glass industry, should this be contemplated at any time. The present investigation was undertaken in an attempt to provide a cheaper source of silica sand within the Province. In 1936, a large number of beach and bank sand deposits in the lower coastal region of British Columbia were examined by the British Columbia Department of Mines, and samples were analyzed chemically and mineralogically. The deposits over the whole area proved remarkably uniform in mineral composition, consisting essentially of quartz, feldspar, ferromagnesian minerals, rock fragments, and various accessory minerals, and differing only in the relative proportions of the various constituents. In no case did the quartz content of any sand exceed about 40 percent and the average was of the order of 20 to 30 percent.

Jan 1, 1947

By T. Motegi

Semisolid casting provides grain refinement of the cast structure and prevents macro-segregation. The conventional semisolid slurry is obtained by electromagnetic or mechanical stirring. In our process, the magnesium alloy (AZ31) slurry is made using an inclined cooling plate instead of the conventional methods. The slurry obtained is cast into a twin-roll caster and makes a continuous sheet of 2 or 3 mm thick. The most important factors that influence the sheet casting are the casting temperature and twin-roll speed.

Jan 1, 2007

By R. Poulin, M. R. Samis

Real options valuation is an alternative net present value framework that is able to incorporate both management flexibility and dynamic project risks. In this paper, management is considering the development of a satellite low-grade zone while operations in a developed high-grade zone continue. If the lowgrade zone is developed prior to high-grade zone exhaustion, mine capacity must be expanded before additional production from the low-grade zone can be processed. This expansion can be avoided only if low-grade zone development is delayed until the high-grade zone is exhausted. The real option model presented here allows the development and capacity expansion decisions to be reconsidered on a discrete half-year basis. It delineates price regions, for given levels of high-grade zone reserves, in which it is optimal to develop the low-grade zone, defer low-grade zone development and abandon the mine irrevocably.

Jan 1, 2006

By Luke Meers

Roadway development rates in Australian underground coal mines are failing to keep pace with modern longwall systems and are unlikely to sustain further improvements in longwall productivity into the future unless step change improvements to roadway development equipment and practices are made. Bottlenecks which limit and constrain improved production and impact the safety of operators have been identified through a series of industry surveys, with the manual installation of strata support materials, consumables delivery, coal haulage and monorail installation being highlighted as major areas to improve development performance. This paper looks at research being carried out at the University of Wollongong in designing an integrated system approach for the fully automated handling and installing of development consumables, and the systems required to support these activities. A series of hard automation manipulation devices have been demonstrated in surface trials and the results indicate that rapid roadway development can be achieved.

Aug 1, 2013

By C. I. Walker

Field tests at a number of large mineral processing operations have been undertaken to better understand the wear life impact of different aspects of pump design, materials of construction and maintenance procedures. Data are presented for wear rates, and typical result variability is explored. To improve the availability of pumping equipment in a milling circuit it is not only important to improve the wear life, but also reduce the variability in the wear life of components so that the incidence of premature failure is lessened. Localised gouging wear due to flow separation and turbulent eddy formation is often the point at which part-holing occurs. A number of improvements to the design of pump impeller and throatbush (suction side liners) to reduce the localised gouging wear are outlined. Also, results are presented on the use of composite materials (mix of metal, rubber and ceramic) for throatbush materials to protect specific areas against wear.

Jan 1, 2012

By N. Dave

"IntroductionIn the mineral processing industry, certain minerals such as uranium, thorium and vanadium, etc., are selectively extracted with high degree of purity from solutions containing variety of other impurities by solvent extraction process. This separation process consists of bringing two immiscible or partially soluble liquid phases in contact, where mass transfer of one or more components takes place by ion exchange under certain controlling parameters such as pH, salt concentration and temperature. The processes taking place are primarily physical because the solutes being transferred are ordinarily recovered without chemical change. For efficient extraction more than one stage is required and the solutions are recycled counter currently through other stages. A multi-stage counter current solvent extraction plants essentially consist of four circuits namely: extraction, water wash, stripping, and solvent scrubbing. In extraction circuit the desired mineral is extracted at a certain pH from an aqueous solution onto an organic solvent by bringing them in contact with mixing in large mixer-settler units. The mixed solutions are allowed to settle and separate into component organic and aqueous phases in horizontal settlers by providing sufficient residence time. The solutions are then moved counter currently to other units- the aqueous from the underflow and the solvent organics from the overflow of the settler. The solution streams coming out of extraction circuit are loaded organics and barren aqueous or raffinate solution. The loaded organics are washed with water in a water wash circuit to remove transported impurities from extraction circuit. In the stripping circuit, the desired mineral is stripped selectively from the solvent phase back into an aqueous phase with a stripping agent at a selected pH. The solution stream leaving, stripping circuit are stripped organics and pregnant strip (aqueous) solution. The stripped organics are scrubbed off other loaded impurities with a conditioning solution in, scrubbing circuit and the cleaned solvent is re-used in the extraction circuit.A typical solvent extraction plant for uranium extraction and purification at Agnew Lake Mine is described in this chapter."

Jan 1, 1989

By E. G. Gaylord

THE material improvements which have been made in the practice of exploiting oil and gas reservoirs in the United States during recent years may be attributed largely to: (1) The necessity for drilling deeper wells at costs not much greater than was formerly expended on shallower wells. (2) The necessity for producing oil at a lower cost per barrel. (3) A growing recognition of the importance of the nature of production practice upon ultimate yield of oil and gas. The first two of these factors result, to a large extent, from the fact that a greater proportion of new development has been deeper development, and these wells have been drilled in the face of progressively lower per well allowables. In California, for instance, maximum allowables have declined from 400 barrels per day in March, 1938, to 156 barrels per day in September, 1940, and during this same period some 125 wells were drilled to the deeper 10,000-foot producing horizons discovered during this time. The third item listed above results from our increasing knowledge of the basic factors which influence the amount of recovery we may expect from reservoirs. In addition to the longer-range planning now being undertaken by the more prudent operators, State proration and conservation laws have focused attention upon the importance of methods conducive to obtaining progressively greater quantities of the hydrocarbons in place. In a paper of this length it will be possible to discuss only a few of the recent advances. An effort has been made to select the more important of these and to indicate, where possible, the factors which have made these advances possible.

Jan 1, 1941

By C. M. Campbell

THE dire effects of rapidly vanishing natural resources, widespread unemployment, and increased debt and taxation in recent years have challenged Canadians to produce a practical solution to these national economic problems. In more recent months, wars and rumours of war have indicated, among other things, the need for better control of our mineral wealth. The erection of a smelter on the lower mainland coast of British Columbia, treating all Western ores, and such ores as it will be found advisable to import, will make an important contribution toward a solution of these problems. It is believed that the ores tributary justify a smelter of major proportions. A stock-taking to confirm this can be made with reason-able accuracy in a short time, and this should be undertaken without delay. Enough general information is, however, available .in this paper to justify the technicians of the Department of Mines at Ottawa and of interested smelting companies making a preliminary study of the matter. THE DEFENCE ARGUMENT As a factor in rearmament, metals play a vital part. That rearmament is to continue on an increasing scale is indicated in Premier Chamberlain's address of October 3rd last, when he said: ?'For a long period now we have been engaged in this country in a great programme of rearmament which is daily increasing in pace and volume. let no one think because we have signed 'this agreement between the four powers at Munich we can afford to relax our efforts or call a halt in our armaments at this moment'. As matters stand, the facilities in British Columbia are entirely out of line with the strategic importance of this Province as the Western Front of Canada and the Empire. All our copper ores, and an appreciable part of our lead and zinc ores, are sent for treatment to Japan, United States, and Europe, while we import our iron and alloys. A treatment plant on this Coast would not only give us control of war metals and chemicals but it would provide an increased industrial and research population, badly needed in this area and of the greatest value in the case of war. This is where the mining industry can do its bit.

Jan 1, 1939

By M. S. Moats

"The effects of commercial copper electrorefining additives (glue and thiourea) on the electrochemical removal of bismuth are of importance in copper production. It was found that Bi(III) electrodeposition occurs readily from acidic sulfate solution via a diffusion-controlled quasi-reversible reduction. The diffusion coefficient of Bi(III) was measured and found to be less than reported values of copper in similar solutions. The presence of thiourea and/or glue was found to accelerate or de-polarize Bi(III) reduction on stainless steel as compared to the inhibition or polarization of Cu(II) reduction. The additives also inhibited the dissolution of the Bi-Cu co-deposit during cyclic voltammetry. During short term deposition studies, the additives increased the concentration of Bi in co-deposited Cu-Bi products from solutions with low concentrations of Cu (<2 g/L). Bi deposition was significantly suppressed by increasing the Cu(II) concentration in the solution. The formation of a copper layer on the stainless steel electrode appeared to significantly suppress the reduction of Bi(III). This study demonstrates that glue and thiourea depolarize the deposition of bismuth on stainless steel. Therefore, the additives could be used to improve Bi impurity removal during third stage liberation.INTRODUCTIONThe production of high purity copper has been steadily increasing due to the wide application of the metal and its alloys in electrical and electronic products, infrastructure construction, industrial machinery and equipment, general products and transportation (Moskalyk et al., 2003). Most high purity copper is manufactured from copper sulfide mineral concentrates and/or scrap via a pyrometallurgical process followed by electrorefining (Navarro et al., 1999). During the electrorefining process, cast anodes of 99-99.5% purity are electrochemically dissolved into an acidified copper sulfate solution while high purity copper (>99.99%) is plated on stainless steel blanks or copper starter sheets (Davenport et al., 2002). The control of cathode deposit growth (purity and morphology) while maintaining a high current efficiency is of significant importance for copper refining (Ilkhchi et al., 2007). At typically applied current densities for industrial copper electrorefining, mass and charge transfer play important roles in the quality of cathodic products (Hiskey et al., 1998). If the real current density at some surface points is substantially higher owing to uneven current distribution, then rough spots can and will grow faster leading to nodules (Suarez et al., 1992). Nodulated deposits tend to capture solution and anode impurities (slimes) resulting in unacceptable cathode quality (Afifi et al., 1987). Furthermore, these nodules can grow until they eventually contact the anode leading to short circuits and current efficiency reduction (Ilkhchi et al. 2007)."

Jan 1, 2016

By Mousa Mohammadi

Due to operational advantage of dragline in simultaneous excavation and back-filling, the equipment has gained vast importance in open-pit mining. Besides, absence of auxiliary haulage units and a myriad of other benefits are also credited in favor of excavation of muck piles by the draglines. However, the aspects of production, productivity and economics are of utmost significance in dragline operation and planning. In this light, the present paper is an endeavor to analyze availability and utilization of dragline operations. The paper presents a good amount of data for 4-draglines operating in one of the major opencast projects in India. The study reveals the trends of availability and utilization of these draglines during last 11-years. Furthermore, the study also highlights the salient reasons for loss of available hours and for idling of the draglines. Some startling information and facts have been illustrated in form of graphs and pie charts.

Aug 1, 2013

By G. R. Waters

"The technology behind industrial applications such as Hydrometallurgy continues to evolve, as do the corresponding regulations and specifications that ensure the safety of workers and the environment. Valves make up key aspects of this technology, and often represent the single point of failure for entire operations. More often than not, the valves being used in Hydrometallurgy applications are known as Severe Service Valves (SSVs) due to their ability to withstand the extreme conditions. Most experts agree that SSVs are identified by applications, and that these applications are challenging to the valve’s ability to provide a minimum acceptable level of performance over a minimum acceptable duration. The Manufacturers Standardization Society (MSS) of the Valve and Fittings Industry has designated Ross Waters, President of CGIS, as Lead to the Task Force put in place to determine the minimum requirements a valve needs to be able to perform to when faced with extreme conditions, whether from pressure, temperature, toxicity, solids, or usage. This paper serves to determine what the minimum requirements are for SSVs in Hydrometallurgy applications. It will draw on five decades of industry experience from one of Canada’s leading valve experts.INTRODUCTION Severe Service Valves Severe Service Valves (SSVs) mean different things to different people. Until today, defining SSVs had little if any global agreement or recognition. That is about to change as the Manufacturers Standardization Society (MSS) has accepted an application to produce a Standard Practice so defining them. This paper provides information about the selection of SSVs in all industries but focusses on metallurgical processes and applications and offers examples to illustrate the successful and unsuccessful use of these valves. All of this with the purpose of raising the awareness of the industry on all sides, from the suppliers and manufacturers, specifiers and to the users and owners of them. It also supplies tools to understand where and why to separate SSVs from general purpose or commodity valves (GPVs). SSVs are often identified by applications, and these applications are challenging to the valve’s ability to survive. Within these applications the elements that make the service severe are being analyzed, quantified and qualified. From this, we expect to offer objective and repeatable definitions and guidance to improve the experience of SSVs, reduce unnecessary costs, provide longer service life and process runs, improve safety and reduce environmental issues."

Jan 1, 2017

By C. P. Jenney

"Exploration for copper, in a region of 7,000 square miles on the Arctic coast between longitudes 114 and 118 degrees west, has covered a period of nearly 200 years. Occurrences of native copper, used by the natives for tools and weapons, have been reported since the early part of the eighteenth century. In J 771 Samuel Hearne of the Hudson's Bay Company, in the course of his classic 3-year journey from Fort Churchill, became the first white man to see the deposits, and incidentally the first to reach the Canadian Arctic coast by land. During the next 140 years the deposits were mentioned by every explorer and traveller who passed through the area. A good historical summary of this literature has been presented by Tyrrell (1912).In 1911-12 the Douglas-Sandberg party did the first geological mapping along the Coppermine River and Dismal Lakes (Douglas, J., 1913; Douglas, G. M., 1914), and described the copper occurrences there. In 1914 J. J. O'Neill (1924) of the Canadian Arctic Expedition investigated the showings on Bathurst Inlet. In 1929-31 two Canadian exploration companies sent prospectors and geologists to the area (Gilbert, 1931; Norrie, 1931; Duncan, 1931). Since that time only brief references have been published (Kidd, 1931; Stockwell and Kidd, 1931; Lord, 1941, 1951; Washburn, 1947). In 1943-45 an area of more than 1,500 square miles was prospected by American Metal Co. of Canada, Ltd., under the direction of the writer. Forty-nine showings were examined; seven of these were mapped in detail by plane-table and two were sampled by 27 short diamond drill holes totalling 3,061 feet. All holes were in permanently frozen rock, and the deepest vertical distance reached was 206 feet. Five groups of claims were staked. These later lapsed, but one of the groups was restaked in 1951, and assessment drilling and some trenching were carried out in 1952-53. Results were disappointing, and the claims have been allowed to lapse.The area is within the Arctic Circle, northeast of Great Bear Lake and 360 miles north of Yellowknife on Great Slave Lake. For exploration purposes, access is by aircraft from Yellowknife. During the short open season heavy freight can be brought by sea to Coppermine at the mouth of the river, either from Aklavik at the mouth of the Mackenzie or around Alaska. Concentrates would have to be moved by these routes.Although none of the deposits so far found is mineable under present conditions, the total volume of copper in the numerous showings marks the district as a major area of copper mineralization, which may some day be of economic importance."

Jan 1, 1949

By T. B. Williams

A SEARCH of the records indicates that evidences of accumulations of petroleum and natural gas within the boundaries of British Columbia were discovered at approximately the same time as were those of Alberta. They probably would have been developed as soon bad it not been for the fact that they are in such uninhabited parts of the Province. Even today, the seeps of the Flathead area, and the later discovered extensive seeps of the Peace River area, have been seen by very few people. From the geological evidence, there is reason for believing that British Columbia soon will be a petroleum producing Province. Fifty-eight operators, both companies and individuals, are now backing the money and the effort which they have invested with us, for the most part within the last three years, in a belief that this is so. The promulgation of the Petroleum and Natural Gas Act in 1947 marked the beginning of a new phase with regard to the exploration and the development of our petroleum and natural gas resources. Since August 15th, 1947, the date on which the Act came into force, the area under exploration bas increased from a few thousand acres, held by lease under the Goal and Petroleum Act, 1986, to 10,460,115 acres, including all active permits, licences, and leases. In addition there are 192,720 acres under application, bringing the total under issue and application to 10,652,835 acres. The total area is comprised of 105 permits, 20 licences, and 26 leases under the 1986 Act. The permits and licences, which ?represent active exploration and development, are held by a total of 82 companies and 26 individuals.

Jan 1, 1951

By E. J. Wasp, T. L. Thompson, T. C. Aude

The paper will deal with some of the more important technical aspects of slurry pipelines as they apply to the mineral field. In addition, the use of these technical concepts in arriving at realistic economic figures will be discussed.

Jan 1, 1970

By N. Haghdadi, D. M. Maijer, A. B. Phillion

B206 is a recently-developed high-strength Al-Cu casting alloy with reduced Ti and Fe, as compared to the well-known AA 206 alloy, for improved hot tearing resistance. In the current study, the solidification kinetics of this alloy as a function of cooling rate from 1 to 15 K/min were studied using differential scanning calorimetry (DSC) and microscopy. Specifically, the evolution in fraction solid, grain size, and secondary dendrite arm spacing have been characterized. The DSC results show the occurrence of three peaks during cooling from the liquid state, which are related to the formation of primary aluminum, a pre-eutectic intermetallic, and the eutectic phases. Thermal analysis also indicates that while the liquidus temperature is not sensitive to the cooling rate, the temperatures at which the pre-eutectic and eutectic phases form are strongly coupled to the rate of heat extraction. A decrease in the latter temperatures was observed when the rate of solidification was increased, leading to a lengthening of the freezing range of the primary phase. The results will be useful for improving B206 casting processes, specifically through modification of mould cooling conditions.

Jan 1, 2014

By Tetsuya Yumoto, Toshikazu Shiratori

Information on the elements contained in E-Waste is important from the viewpoint of recycling. We analyzed several components of waste electrical and electronic equipment (WEEE) collected from citizens. The distributions of the minor metals in WEEE were determined with elemental mapping and chemical analyses. The annual change in elemental composition was investigated by analyzing equipment manufactured in different years. The information will be of use for separation techniques required for future advanced recycling.

Jan 1, 2011

By A. G. Lylie

Introduction At the Britannia Mining and Smelting Company&apos;s mill, the equivalent of 2,500 to 2,800 pounds of copper sulphate crystals per day is made from copper which is precipitated from the mine-water. This copper sulphate is used in the mill for the recovery of sphalerite by2 flotation. From 1932 until 1936 it was produced by exposing the precipitate to air for thirty days and then dissolving the oxidized copper with dilute sulphuric acid. In 1936, the flotation of sphalerite was discontinued and, when it was resumed in 1947, steps were taken to try to improve the former method. The present paper outlines the way in which this was done, and describes the plant and procedure by which copper sulphate is now being made, and by means of which an appreciable saving is being effected. Aboratory Tests The previous work had established that the precipitate, which consists mainly of metallic copper, must be oxidized before the copper would dissolve in dilute sulphuric acid. Various methods for oxidizing it were tried but in the early laboratory work the only suitable one found was to heat the precipitate to 600°C. and hold it at this temperature for two hours. When this was done, approximately 90 per cent of the copper became soluble in .acid. This percentage was considered satisfactory for practical purposes, but the cost of roasting was prohibitive because only a small amount of roasted precipitate was required each day.

Jan 1, 1951

By D. A. Sloan

THE Young Davidson mine is of particular interest because of the extremely low costs and also because of the novel method devised for pillar recovery. The outstanding feature of the mining system is its simplicity and regularity. The successful operation of this property was de-finitely assured by the rise in price of gold in 1934. The mine is situated in the southeastern part of Powell township, about forty-five miles southeast of Timmins, Ontario. The local town, two miles distant, in Matachewan, which is twenty-five miles northwest of Elk Lake, the terminus of a branch line of the Temiskaming and Northern Ontario railway. Mining is confined to one of a group of five claims. The ore occurs in a body of syen.ite porphyry which is intruded along a contact of Timiskaming conglomerates with Keewatin altered ruffs and greenstones. This intrusion extends in a north-easterly direction from Davidson creek for 3,300 feet, of which length 700 feet lies within the Matachewan Consolidated property. The maximum width of the mass is 700 feet; it tapers off as it extends east-ward. The Orebody.-The syenite porphyry is of three types, probably all differentiates of the same magma, but only one of them is gold bearing. This is a cherry-red, coarsely crystalline type which forms the central part of the mass. It is more brittle and more fractured than the others, and consequently has allowed easier access to the gold-bearing solutions. The gold has been brought in by a branching system of quartz veins and along minute fractures. It is mainly in the form of very fine &apos;free&apos; gold, but also occurs in pyrite, which is the chief metallic mineral.

Jan 1, 1942

By J. Beland

The Rimouski-Matapedia region is along the southwestern extension of the central Siluro-Devonian synclinorium of Gaspe Peninsula. As in Gaspe about 30,000 feet of Siluro-Devonian strata rest on a "basement" of tightly folded Ordovician rocks. The central synclinorium is divided up into two northeasterly trending belts each of which is characterized by distinctive lithologies and patterns of folding. The northwestern belt is gently to moderately folded and includes lithologies which point to a stable environment. The southeastern belt on the other hand is tightly folded and the lithologies indicate a less stable environment. A marked angular unconformity separates the basement from the Siluro-Devonian cover near the north-western margin of the northwestern belt. At the southeastern margin of the southeastern belt the relationship of cover to basement has not been as-certained because of a fault. The northwestern belt has several features significant in the search for petroleum; the Silurian strata are exposed in broad open anticlines

Jan 1, 1962