Search Documents

By V. Vakiloroaya

The paper aims at developing a hybrid solar-assisted air conditioner system for performance enhancement and energy efficiency improvement. To increase sub-cooling of the refrigerant at partial loads, we propose a new discharge bypass line together with an inline solenoid valve, installed after the compressor to regulate the mass flow rate of the refrigerant vapour passing through a hot water storage tank. For control design, a lumped parameter model is first developed to describe the dynamics of the system in an explicit form of input-output relationship. The system has been fully-instrumented to examine its performance under different operation conditions. The system model is then validated by extensive experimental tests. The predictions from the models exhibit a good coincidence with experimental results, judging by an RMS error less than 15%. Based on the obtained dynamic model, a linear quadratic regulator (LQR) is applied to optimize a cost function of the output errors and control efforts. The key challenge is to regulate the refrigerant temperature entering the condenser by controlling the valve opening. The design approach is then tested in a transient simulation tool to predict the system performance in transient conditions. The experimental results obtained from implementation with PLC demonstrate that the proposed system delivers higher system efficiency owing to the higher refrigeration effect in the direct expansion evaporator. Thus, the novel development is promising for improvement of energy efficiency, enhancement of the system performance while fulfilling the cooling demand. Consequently, between 25 and 43% of monthly electricity can be saved on average.

Aug 1, 2013

By N. R. Thote, J. L. Porathur, C. P. Verma

Highwall mining is a highly mechanized coal mining method associated with several advantages, such as a very high production rate (approximately 3,000 t/d) and low production costs. There is no requirement for underground support, ventilation, or blasting. Production leads to added recovery, which is otherwise lost in the ultimate pit. The use of highwall mining can bridge the gap that exists between supply and demand in the energy sector. This paper presents a brief review of highwall mining technology, including current status, analysis tools, and design techniques. In addition, it identifies important parameters from the analysis of failure case studies.

Jan 1, 2014

By F. T. Mooney

Introduction The Flin Flon mine of the Hudson Bay Mining and Smelting Company, Limited, is on the interprovincial boundary between Manitoba and Saskatchewan, about four hundred miles north of the Canada-United States boundary. The orebodies are gold, silver, zinc, and copper replacement deposits occurring as irregular lenses of massive sulphides, arranged en echelon, and irregular masses of disseminated copper sulphides in chlorite. The country rocks are of Precambrian age, dominantly lava flows. Development of the Mine The mine is opened by two vertical main shafts- the North Main and South Main shafts- 3,800 feet apart. The North Main shaft has a depth of 2,210 feet and the South Main shaft is completed for stoping operations to the 3,250-foot level (see Figure 1). These shafts are connected by main haulages driven, on the footwall side of the orebodies, at 520-foot intervals down to the 2,210-foot level. No. 3 (subsidiary) shaft is on the footwall side of the orebodies at a point between the North Main and South Main shafts, 2,400 feet south of the former. It has a depth of 3,250 feet and connects with all main haulage levels- with both Main shafts down to the 2,210-foot level and with the South Main shaft on the 2,750-, 3,000-, and 3,250-foot levels. Other openings tO the mine include B North fan raise, the opening due to the recovery of the open pit sill pillar, and several back-fill raises.

Jan 1, 1949

By P. Mengé

The covering of a hydraulically filled goethite pond is discussed from a geotechnical point of view. The characteristics of the goethite were defined in order to allow a detailed study of the procedure for the construction of the cover on top of the soft material and a verification of the stability of the cover and side slopes after construction. These characteristics and the main results of the studies are given, as well as the experiences and observations made during the execution of the work. Finally, the monitoring plan, during and after construction, is also discussed and some results are given. The 'Design and Construct' contract form was used to allow the contractor to choose the optimum and most economical method to realize the closing of the pond, based on his experience with similar projects. The works were carried out between mid 2003 and the end of 2004. The paper will, amongst others, discuss the special method of working that had to be developed to allow the covering of the whole pond in a relatively short time period, without soil improvement methods such as vertical drains or stabilization by in situ treatment. Fill material was used to establish a platform on top of the soft material so that the cover liner and finishing layer could be installed on top of the fill layer. The 'floating roof' principle was used; subsidences were allowed to occur during the installation of the impermeable top liner and soil cover.

Jan 1, 2006

By G. J. McTeer, D. L. Verhelst, D. J. Rioux

Teck Metals Ltd. operates an integrated zinc-lead complex at Trail, British Columbia, Canada. Since 1997, KIVCETTM flash smelting technology has been utilized for the treatment of zinc plant residues and lead concentrates. Trail Operations’ furnace uses four water-cooled jackets for bullion tapping. This paper provides an overview of KIVCET bullion tapping for the past 16 years, and discusses successes and challenges encountered with respect to operations, training and monitoring.

Jan 1, 2015

By K. T. Audt

The Yayoi period, from about 300 B.C. to A.O. 300, represents a time of important changes in Japanese history. During this period the advanced rice culture of the Asian continent was introduced to Japan, along with the techniques of animal husbandry, spinning, bronze casting and metal working(1) . As was the case in the Jomon period (11000 B.C. to 300 B.C.), the Yayoi period is traditionally defined by a particular type of pottery, characterized by the use of the potter's wheel and an extreme simplicity of decoration and form(2) . Pieces of this pottery were found in 1884 in a district of Tokyo, known as Yayoi-Cho, not far from Tokyo University. Within a decade the name Yayoi had come to be used for the period which also saw the first casting of metals in Japan121. During the Yayoi period, the foundation of the ancient Japanese state was laid as the individual small communities were unified and as labour specialization and social levels developed. In fact, the Yayoi may be the true ancestral culture of Japan(3) . However, the origin of the Yayoi is not definitely known. One theory indicates that the Yayoi people may have been driven from the Asian mainland (via Korea) by the dynastic wars that accompanied the unification of China under the Ch'in and Han and that these settlers rapidly displaced the Jomon. Bronze objects and the cultivation of rice may have arrived about the same time - in the third century B.C. Iron was in Japan within another century, but since it rusts badly and disintegrates, only a few small pieces are known from such an early date(4) . After about 50 B.C., the Yayoi cultures of western Japan were in fairly close and regular contact with the continent via Korea(5)

Jan 1, 1999

By J. Keith Haddock

"Introduction The Luscar company, Forestburg Collieries Ltd., operates the Diplomat Mine located 14 km south of Forestburg, Alberta. Production is now at a declining rate from the 1 million tonnes achieved in 1978 as the reserves are being depleted. Three pits are operated at this prairie strip mine utilizing draglines and stripping shovels to uncover the coal. The coal is hauled to a tipple on site for shipment by rail or highway vehicles or is hauled directly to the adjacent Battle River Generating Station. Geology The mine is currently extracting the Battle River seam on the north side of the Battle River. This is the lower-most seam in the Horseshoe Canyon Formation and is the only one present in the area, the upper seams having been eroded by glaciation. The seam lies generally flat and varies from 2.0 to 5.0 metres thick. It lies under glacial till overburden varying in depth from 5.0 to 12.0 metres. The mineable coal extends from the side of the Battle River valley where it outcrops, to approximately 2.5 kilometres to the north. The mine is spread out over a distance of 8.0 kilometres in an east-west direction. Reserves and Coal Quality After over 30 years of mining at Diplomat, there are now less than 1 million tonnes of mineable reserves remaining on the property. With the commencement of coal production from the Paintearth Mine in 1981, supply to the Battle River Generating Station, formerly Diplomat's biggest customer, is being transferred to Paintearth. Rail shipments and domestic supply will continue until reserves are depleted. The coal has the following specifications:"

Jan 1, 1985

By R. P. Nicholson

On September 3rd, 1947, the Acadia Coal Company put into operation a central coal preparation plant. This plant was designed to process all coals mined by this Company in the Pictou County coal field. The problem, briefly, was to make a three-way separation of the raw coal fed into the plant. It was desired to remove all stone, metal, and wood from the marketable coal and to produce a splint coal from the raw material which would be suitable for making power. This splint coal product is belted directly to the power plant which is adjacent to the wash plant. To attain this object it was therefore necessary, first, to wash the raw coal, removing all splint, stone, metal, and wood. The stone, metal, wood, and highest-ash splint had then to be removed by a second washing in order to obtain the lower-ash splint for use in the power plant. The plant is on the east side of the Allan colliery, in the town of Stellarton (see accompanying photograph). It is of steel frame construction with wood siding, covered on the exterior with corrugated galvanized iron. Considerable concrete had to be poured for the foundation piers as the plant site is largely 'fill' ground. This necessitated the construction of extremely heavy footings containing a large amount of reinforcing steel. In all, 884 cu. yds. of concrete were poured for the various pits, tanks, and foundations; its average test was about 3,500 lb. per square inch. At the time the plant was constructed, the steel shortage in Canada and the United States was acute and, in order to obtain steel for the structure which is four stories high- an unused part of the Allan bankhead was torn down. Enough steel was obtained from this demolition to fabricate the new plant.

Jan 1, 1948

By F. Henríquez, V. Iriarte, L. Vinnett, J. Yianatos, F. Díaz

Metallurgical characterizations of the collective (Cu/Mo) and selective flotation plants were carried out in Minera Los Pelambres, Chile. The selective plant allows the valuable minerals of Cu and Mo to be separated. The evaluation involved two surveys consisting of metallurgical sampling as well as residence time distribution (RTD) measurements to determine load distribution. The RTD data were obtained in real-time by means of the radioactive tracer technique. In addition, metallurgical data was reconciled and supported by effective residence times. In the collective plant, a performance comparison of parallel rougher circuits was carried out, which included a bank of six mechanical cells of 250 m3 and banks of nine mechanical cells of 130 m3. In the selective plant, the Cu and Mo evolution along the plant was evaluated. The results in the selective plant allowed for performance evaluation of mechanical and pneumatic cells in primary flotation. In both plants, mineral losses were evaluated and their relationship with circuit configuration (cell types and circuit layout) was determined. The metallurgical characterization was a powerful tool to evaluate circuit performance and to detect improvement opportunities at industrial scale.

Jan 1, 2015

By J. Lammers, D. Adams

Most pressure oxidation operations introduce oxygen through a large multi-use nozzle in the vapour space of the autoclave. Sparge pipes extend inside the vessel to the point of discharge below the compartment agitator. However, two zinc pressure leach operations have successfully used a bottom entry oxygen sparge system for a number of years. Recently, the concept has been used in a whole ore gold pressure oxidation operation as well as a copper pressure leach plant. Both of the latter operations also introduce cooling water for temperature control through the same sparge pipe. This paper addresses the benefits of the bottom entry system with regards to autoclave performance and the positive effects on agitator performance.

Jan 1, 2004

By I. Paredes, R. Díaz, H. Henao

Smelting of copper concentrate generates a significant amount of dusts which are collected in electrostatic precipitators. This material, which is a complex oxide of Cu, Fe, S, As, Sb, Bi and others, is difficult to recirculate into the smelting process due to the reported high concentration of arsenic. However, the dust also has concentration of copper above 10wt %, aside from reported contents of silver corresponding as much as 25wt% of the total inventories of this element in the smelters. Thus, it is of economic and environmental interest the development of a process able to reduce the concentration of arsenic in the dust and produce a material suitable to be recirculated into the smelting process. The present experimental work shows the results of a process of dust sulfidization-oxidition able to remove more than 65wt% of the arsenic present. INTRODUCTION Copper sulfide deposits worldwide exhibit increasing concentrations of arsenic. One case of interest would be the copper ores from the northern zone of Chile, which report high concentrations of enargite (Cu3AsS4) (Revista química, 2015) (Latinominería, 2014). The obtained concentrate from this ore is treated in a Fluidized Bed Roaster, producing calcines with low concentration of arsenic (<0.5 wt% As). This material is suitable to be treated in a Flash Furnace. At the roasting process, the arsenic is volatilized and then precipitated as fine particles of complex oxides. Most of this particulate material is removed from the gas stream through a device called Electrostatic Precipitator (Minería chilena, 2014). The experimental results reported in the literature indicate that arsenic present in these particulate materials (or dusts) cannot be eliminated in oxidizing atmospheres (air) or with inert gases (N2) in a Fluidized Bed Roaster even at temperatures as high as 700°C. There is also information that even the recovery of valuable metals from the dust is difficult through hydrometallurgical processes (private communication). This is how in some foundries these dusts are considered environmental liabilities. Regarding the decomposition of enargite (Cu3AsS4) in neutral atmosphere, it is reported in the literature (Padilla, 2001) that the main chemical reactions are:

Jan 1, 2019

By Tong Guan, Guangqin Fu, Lihong Deng, Yuanlin Chen, Xiaotong Zhou

"In natural world, some kinds of scheelite minerals are rich in molybdenum. Molybdenum exists in the crystal lattice of scheelite in the form of isomorphism, and the content of MoO3 varies from 2% to 10%. As a result, the flotability of seyrigite (scheelite with molybdenum) turns to be weaker. One seyrigite mine, which has been built for 3 years,still could not produce qualified seyrigite concentrate due to the weak flotability of seyrigite (Mo-bearing scheelite) in raw ore. In our experimental research, through adopting new seyrigite collector TA-3 and advanced mineral processing technology, the seyrigite concentrate with a grade of 65.62% WO3 at a recovery of 87.47% was obtained for the raw ore containing 0.19% WO3 and 0.074% Mo. By applying the new technical achievement, for the raw ore containing 0.272% WO3, the seyrigite concentrate assaying 68.03% WO3 with a recovery of 77.56% was obtained in industrial production.INTRODUCTIONIn natural world, some kinds of scheelite minerals are rich in molybdenum. Molybdenum exists in the crystal lattice of scheelite in the form of isomorphism, and the scheelite is changed to be seyrigite (Ca[(W,Mo)O4]) (Ma, Bian, & Wang, 2013). The content of MoO3 in seyrigite varies from 2% to 10% usually, the content of MoO3 in some of the seyrigite even reaches 34%. The flotability of seyrigite is weak (Zhang, 2007), and the seyrigite is difficult to be recovered by flotation with common collectors and regulators. One scheelite mine in Anhui China, which is a skarn type seyrigite mine, has not produced qualified concentrate yet since 3 years it has been built due to the limit of beneficiation technology. Therefore, it is necessary to conduct research on the collectors with high efficiency and developing advanced processing flow for this kind of ore."

Jan 1, 2016

By H. Helmstaedt, P. Thurston, R. Harrap

"Evolution of the continental lithosphere over Earth’s 4.6 billion year history is one of the fundamental questions of geoscience. Much of the Earth’s present-day continental crust formed during the first 2 billion years, the Archean eon, of the planet’s lifetime and thus, Archean processes of lithospheric formation must be studied in order to address this question. Until recently, the processes of Archean lithospheric evolution were thought to be fundamentally different from present-day plate tectonic processes. However, subsequent evidence suggests that the growth of Archean continents may be explained in terms of modern tectonic accretionary tectonics similar to those presently operating in the southwest Pacific region. The evidence supporting this hypothesis was compiled largely by Canadian geoscientists working in the Superior Province of the Canadian Shield in northwestern Ontario, over the past 15 years. Study of Archean rocks is also economically important because the Archean rocks of the world, although comprising only a relatively small fraction of the exposed continental crust, contain much of the world’s mineral wealth, including more than half of the world’s gold, as well as significant base metal reserves. Furthermore, the vast majority of primary economic diamond deposits are derived from the lithospheric roots beneath Archean cratons.The LITHOPROBE Western Superior Transect is located within the western part of the Superior Province in northwestern Ontario (Fig. 1). The Superior Province is the largest and best exposed Archean crustal block in the world and forms the nucleus of the North American continent. The internal structure of the Superior Province records a history of the processes that formed the earliest lithospheric elements of the Earth into cratons, thus providing an ideal laboratory for investigating early crustal evolution. The Western Superior Province is characterized by a regional pattern of alternating, 100 km to 200 km wide geological belts (Fig. 2). The observed geologic relationships between and within these subprovinces have been explained in terms of a modern tectonic model of terrane accretion. Oceanic floor, volcanic island arcs, oceanic sediments and continental fragments were accreted successively from north to south against the southern margin of a cratonic nucleus (North Caribou terrane, Fig. 2) which grew steadily in size with the arrival of new terranes through geologic time. If this model is correct, it suggests that the tectonic processes operating today have been active without major variation over the past 3 billion years."

Jan 1, 1998

By V. Gregoire

THE DEVELOPMENT by the Iron Ore Company of Canada of the Quebec-Labrador mining project, which eventually led to &apos;Iron Ore in 1954&apos;, involved, from the start, several distinct undertakings. Among them, the most important were: The construction of a 360-mile railway, linking Knob Lake with Seven Islands. The erection of a railway terminal, and harbour facilities, at Seven Islands itself. The building of an entire townsite at Schefferville (formerly Knob Lake) The construction of two hydroelectric plants; and, finally, The development of a sufficient number of orebodies to enable a production of 10 to 15 million tons of ore a year. Since these phases of the project have already been the subject of previous discussions, this paper will not elaborate further on them but will rather concern itself with a brief outline of the Company&apos;s current mining practices.

Jan 1, 1958

By J. B. Hamilton

The advantages of generating and distributing electrical energy direct from the coal-fields so closely affects the mining industry that a few remarks on the unbalanced phases of coal distribution is worthy of attention. The value of coal imported into Canada from 1912 to 1921 exceeded the sum of $580,000,000. In 1922 Ontario imported 1,640,000 tons of anthracite and 9,440,000 tons of bituminous coal. I submit that the use of Saskatchewan lignite in an electrical super-power plant equipped for the carbonizing of coal, and disposal of excess gases would be the commencement of a solution of the fuel shortage in Ontario. As Saskatchewan becomes more and more populated and manufacturing increases, the amount of by-product carbonized fuel available for shipment to Ontario will increase, and its shipment to that province would decrease the trade deficit of the national balance sheet. If and when this is carried out it will mean a better and wider market for Alberta fuels in Saskatchewan and Manitoba.

Jan 1, 1924

By A. Brown

"The first printed report on Canada's coal resources was published in Paris in 1672(1. Written by Nicholas Denys, then Governor for France of Isle Royale (Cape Breton Island), the report dealt exclusively with the coal of the Atlantic region because little or nothing was known about the interior of North America. Clearly, also, he wrote about a resource of which much was known among the military and early settlers of that day. This early knowledge is not surprising because the presence of coal is clearly displayed in the coastal cliffs of Cape Breton as it was also, at a later date, to the first arrivals on Vancouver Island.An example of early use was that of the French garrison at Fort Louisburg in the first half of the 1700s. Still earlier, in 1643, Governor Winthrop of New England reported the receipt of a small ship load of coal from New Brunswick (2). Despite this early knowledge there was no significant development of coal mines until the 1800s. This had to await the ending of wars between the French and British factions and the growth of population. Basically, also, its development awaited the beginning of the Industrial Age. Organized coal mining began in Canada in 1825 with the formation of the General Mining Association. This British firm was the creation of a group of London jewellers which had been granted royal rights, by the British crown, to all minerals in Acadia (substantially the present Maritime Provinces). The Association took over a number of existing small mines and opened up larger operations in the Sydney coal field. Subsequently, it expanded to the mainland Nova Scotia fields at Stellarton and Springhill. The Association continued in existence as the major coal producer in Canada until 1899 when it sold its properties to the Nova Scotia Steel and Coal Company, Limited (3). This Montreal-based firm managed the coal mines as a major Canadian producer of coal until 1968 when financial problems led to the expropriation of the mines by the Government of Canada. The federal government established the Cape Breton Development Corporation to operate the larger mines on Cape Breton Island. This Crown corporation continues to be a .major producer of coal in Canada."

Jan 1, 1985

By Adrian Dance

Newmont Ghana Gold Limited?s Ahafo operation have been working with Metso Process Technology & Innovation (PTI) since early 2009 to increase mill throughput from a combination of controlled blasting practices and optimised primary crusher and grinding circuit conditions. For such Mineto- Mill projects, PTI?s methodology is termed Process Integration & Optimisation (PIO). Ahafo operate a SAG mill, ball mill and pebble crusher (SABC) circuit that processes a range of primary ore of varying hardness from different pits which is blended with soft oxide material. The PTI study focussed on ball mill limited material from the Apensu open pit. Following a benchmarking study of all blasting, crushing and grinding practices in January 2009, PTI recommended changes in both blasting and crushing conditions in order to generate a finer feed size to the SAG mill. Additional operating changes in the grinding circuit were recommended. A series of trials were conducted in November 2009 where three blasts were fired using a different blast design (hole diameter and explosive type) in the same area of the Apensu pit as the benchmarked material in January 2009. Top and bottom benches (or flitches) from each blast were sent exclusively to the grinding circuit and the material was tracked using PTI?s SmartTag? system. The results from the six trials showed a significant increase in primary ore throughput at a reduced blend of oxide material. Ahafo have since standardised on these modified blasting conditions for all Apensu ore zones and have been able to sustain higher throughput compared to historical performance on similar material. This paper summarises the phases of the PIO project, the changes made in operating practices and the outcomes of the blasting trials that validated the predicted increase in mill throughput.

Jan 1, 2012

By L. B. Smith

Introduction The property of Wright-Hargreaves Mines, Limited is situated at the northeastern end of Kirkland lake, Ontario. It lies immediately east of the Lake Shore mine, and about in the centre of the Kirkland Lake camp. The district is served by the Swastika-Rouyn branch of the Temiskaming & Northern Ontario railway, the town of Kirkland Lake being four miles northeast of Swastika, which is 63 miles north of Cobalt and 392 miles north of Toronto. The mine is developed by three shafts and has more than twenty-eight miles of underground workings. There are two main producing veins, which lie in a porphyry boss 1,350 feet wide. Milling started in May, 1921, and to-date (January, 1933) the mine has produced gold to the value of $21,770,183. Present production is at the rate of 800 tons of ore per day. For a description of the geology, reference may be made to the report by E. W. Todd on the Kirkland Lake Gold Area (1). Structure and Ore Deposits The two major productive veins on the Wright-Hargreaves property are known as the North vein and the South vein. In the vicinity of the shafts these veins are approximately 550 feet apart. A third vein, known as the Inclined vein, has been worked from its junction with the South vein at the 2,000-foot level to its intersection with the North vein at the 800-foot level. This inclined vein has to date been found only in the area east of the eastern major north-south fault. The main North vein and South vein have a general vertical dip, although local rolls and post-ore faults throw certain sections out of line. From the surface to 3,900 feet, the North vein is displaced south less than 200 feet, and the South vein at the same horizon is almost perpendicularly beneath the surface showings.

Jan 1, 1934

By Feng Xue, Mi Xujun, Peng Lijun, Yin Xiangqian, Liu Dongmei, Xie Haofeng, Huang Guojie, Yang Zhen

The Age-hardening Cu-Cr alloys are extensively used in integrated circuit lead frame, railway contact wire, resistance welding electrode and continuous casting mold copper plate, owing to having an excellent combination of high electrical or thermal conductivity and high strength. High temperature performance is very important during the service process. Effect of Magnesium and Zirconium on softening behavior of Cr-Cr alloy are investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). During the softening process in the Cu-Cr alloy, the recrystallization process, grain growth and Cr precipitates coarsening are observed. The addition of Mg or Zr to the Cu-Cr alloy, the resistance to elevated temperature can be significantly improved, owing to being restrained the growth of the precipitates by segregating along precipitates surface. INTRODUCTION Age-hardening Cu-Cr system alloys can be widely uesed in many fileds such as electrodes for spot welding (Hatakeyama et al., 2008; Cheng, Shen & Yu, 2013; Zhou et al., 2016; Chbihi, Sauvage & Blavette, 2012), intergrated circuit lead frame (Hatakeyama et al., 2008; Cheng, Shen & Yu, 2013; Zhou et al., 2016; Liu et al., 2006; Pang et al., Xia et al., 2012; Wang et al., 2009; Huang et al., 2003; Cheng, Yu & Shen, 2014; Zhang et al., 2016; Li et al., 2007) and railway contact wire (Cheng, Shen & Yu, 2013; Zhou et al., 2016; Chbihi, Sauvage & Blavette, 2012; Liu et al., 2006; Pang et al., Xia et al., 2012; Wang et al., 2009; Huang et al., 2003), because it has high strength, good electrical and thermal conductivity. The precipitation behavior of binary or ternary Cu-Cr alloys had been investigated by many researchers (Chbihi, Sauvage & Blavette, 2012; Peng et al., 2017; Batra et al., 2002). In addition, to obtain additional mechanical properties without much deterioration in electrical conductivity, trace addition of alloying elements like Zr, Ag, rare metals (Y and Ce) and Mg are added into Cu-Cr alloy. The addition Mg to Cu-Cr alloy accelerated the process of precipitates nucleation and restrained the growth of the precipitates by segregating along precipitates surface during aging, which enhanced the stability of the deformation microstructure and improved the mechanical properties of the alloy (Zhao et al., 2018). Additional zirconium in Cu-Cr alloy enhances the strength by the decrease in inter-precipitate spacing of Cr precipitates and the formation of Cu5Zr phase (Chihiro, Ryoichi & Kazue, 2008). Owing to the decrease in inter-precipitation spacing of Cr precipitates and to the Ag-atom-drag effect on dislocation motion, the addition of Ag can increase in strength, stress relaxation resistance and without much deterioration in electrical conductivity (Chihiro, Ryoichi & Kazue, 2008). The enhance in strength and electrical conductivity of the Cu-Cr-Zr alloy by adding Ce and Y elements are attributed to removing oxygen and sulfur from as-cast alloy (Li et al., 2006). However, the effect of Mg or Zr element on microstructure and properties of Cu-Cr alloy during the softening process are not clear. Therefore, Microstructure evolution and properties of a Cu-Cr systems alloy were investigated in detail by OM and TEM. The Relationship between microstructure and properties of Cu-Cr systems alloy was also discussed.

Jan 1, 2019

By R. Bruce Ferguson

"The Kettle River Operation of Echo Bay Minerals Company is located about thirty kilometers north of the town of Republic in northeastern Washington State. In tum, Republic is about a hundred and seventy kilometers north and a little west of the city of Spokane, Washington. It is also about fifty kilometers south of the town of Grand Forks, BC, Canada. At this time it is the only gold mining and milling operation in the State.Tailings are stored in a double lined, zero discharge facility. It became evident in mid 1996 that the rate of free water accumulation in the tailings pond was going to result in the level in the pond reaching its permitted freeboard elevation long before the solids plus pore water capacity was reached.We then embarked on a mission to manage tailings pond water on several fronts: reduce fresh water usage in the process, divert spring seeps and surface runoff and install a system to enhance evaporation.IntroductionThe Republic area is an historic gold mining district. Hecla operated its Republic unit from 1892 until closure in 1994. The Kettle River Operation processing plant is located in the San Poi! river valley at an elevation of just under a thousand meters. The facility consists of a ninety thousand ton ore storage pad as the mines are remote and truck haulage is subject to interruption due to weather and road restrictions, jaw and cone crushing with screening, rod and ball milling to an eighty percent passing size of seventy five microns. This is followed by preaeration with high purity oxygen supplied by a vacuum pressure swing adsorption plant plus lead nitrate addition to achieve passivation of the sulfide mineralization such as chalcopyrite, pyrite and pyrrhotite. Conventional cyanide leaching and carbon in pulp adsorption completes the loop. Tailings are treated with air/S02 to achieve cyanide destruction. Plant capacity is 1,815 tons per day. Our license requires that there be no detectable free cyanide in the tailings pond water and a maximum of forty parts per million weak acid dissociable cyanide. The operation started in 1989 with production from the Overlook Mine located about five kilometers further up the same valley at an elevation of twelve hundred meters, hence the location of the mill. Current mine production comes from Lamefoot in the Curlew Lake valley, about ten kilometers distant, and K2 in the Kettle River valley about fifty kilometers away. Both are at an elevation of about 800 meters. Lamefoot produces 1,360 tons per day and K2, 455. Both are underground operations."

Jan 1, 1998