Search Documents

By J. F. Boux

"The study of the total utilization of fly ash has involved all of the known technology in the processing of this waste material into useful products. In addition, a complete knowledge of all the possible uses of fly ash and its products in the market area was probably the most important factor in evaluating the theory and practical feasibility of the total utilization of fly ash from a single large supplyLaboratory tests carried out on the separation of fly ash into different fractions were shown to improve its value and utilization. Four main fractions were studied: a fine pozzolanic low-carbon fraction; a coarse fraction for light-weight aggregate production by pelletizing and sintering; a high-iron fraction; and a carbon-rich fraction. The term ""beneficiation"" here refers to a process of separating fly ash into more useful components.Laboratory and pilot sinter strand tests were employed to optimize the sintering capability and the quality of the heat-hardened pellets through a study of the agglomeration cycle in four principal heat zones, under controlled conditions of air flow, temperature and atmosphere, and including the controlled sizing of pellets.The suitability of the heat-hardened pellets as light-weight aggregate was evaluated in test batches of concrete, which were compared with concrete containing commercial lightweight aggregate of established quality.A study of beneficiated fly ash pozzolan as a partial cementitious binder component in normal and high-temperature cured concrete was reported in a paper at the re-cent Second International Fly Ash Symposium.Samples of raw and beneficiated Lakeview ash were compared with samples of other established high-quality fly ash pozzolans. The evaluation indicated the usefulness of beneficiated Lakeview ash as a pozzolan. Economic studies indicated that to accomplish the primary objective of total utilization of any single source of fly ash (in this case. fly ash from the Lakeview Generating Station, producing approximately 400,000 tons per year), a broad knowledge of the technology of various mineral processes was essential.The design of the fly ash processing plant had to be based on the disposal of all the raw fly ash produced by the generating station. This is contrary to the normal design of a processing plant in which raw materials are supplied and produced according to product demand. The design, therefore, had to be of such flexibility as to pro-duce as wide a variety of products as possible, and the ability to market them had to be well researched and understood."

Jan 1, 1970

By Vishal Shukla, Prateek Singh, D. P. Chakraborty

"Continuous thickening by an operation called sedimentation is the separation of suspended solid particles from a liquid stream by gravity settling. The primary purpose of thickening is to increase the solids concentration of the feed stream. High rate thickeners are designed specifically to maximise the flocculation efficiency. A detailed investigation has been carried out to understand the influence of ore type and operating parameters such as bed level, bed mass, rake arm torque and flocculent concentration on thickening operation. Tata steel’s Noamundi plant data shows that variation in ore type, and operating parameters are major contributors to fluctuation in thickener performance. A lot of research has been done earlier on thickening operation but effect of ore type and operating variables by using plant data was never touched before.In this context, the performance of thickener was evaluated by daily data to study the influence of ore type and operating variables on thickener operation. Investigation shows that friable ore % in feed mix is proportional to slime density because friable ore is porous & brittle in nature. As a result, friable ore generates more fines/ultrafine during communition process in wash plant. Increase in flocculant concentration and bed mass is showing a positive change on high rate thickener performance Investigation shows that optimum bed mass and flocculant concentration is required to achieve desired pulp density in thickener underflow at different feed pulp density (g/cc).INTRODUCTIONOver the years, Iron Ore Beneficiation at Tata Steel, Noamundi has seen varied changes. Depletion of high grade iron and with increasing iron ore throughputs coupled with lowering of the hard ore a subsequent increase in slime generation, slime management and clear water requirement for wet Plant has thrown up myriad challenges. To overcome these challenges, many improvements initiatives were taken by Tata Steel in last decade. One of the major changes is the recent High Rate Thickener commissioning at Tata Steel Noamundi to cater the high iron ore throughput requirement. Slime reporting to Thickener has increased from 1.4 MTPA 2.5 MTPA over the last few decades. The above changes further aggravate the poor settling and dewatering characteristics of the slurry which is being feed to HRT. Considering the above mentioned constraints and stringent environmental implication proper water management has become a major challenge to reckon with. The thickener is used to increase the concentration of the suspension by sedimentation, accompanied by the formation of a clear liquid. In most cases the concentration of the suspension is high and hindered settling takes place."

Jan 1, 2016

By Jeffrey T. McGinty, Frank M. Wheeler

Plant layout is the arrangement of equipment, process areas, departments, infrastructure, and support facilities. Plant logistics is the flow of parts, people, resources, and information throughout the production process. This chapter: outlines key factors and provides checklists to facilitate layout development; presents risk management approaches to test the logistics and functionality of alternative layouts; and uses real-world examples to illustrate effective simulation modelling to assess plant layouts.

Jan 1, 2015

By J. C. Beidelman

One of the oldest settled portions of Canada is that "strip of land" extending into the Gulf of St. Lawrence, known as the Gaspe peninsula, with the Bay of Chaleur on its southern boundary. This "strip of land" is still so very sparcely populated that only at a few places does settlement extend more than a few miles from the coast. ? The peninsula is 160 miles long, 75 miles wide and with the exception of the above mentioned settlements is a mountainous wildness-void of all roads or inhabitants. Developments in the interior, of all nature, out-side of the cutting of timber by limit holders, was entirely lacking until the year 1915, when mining was first commenced. In the summer of 1844 Sir William Logan made a preliminary survey across the peninsula, from Cape Chat on the Gulf of St. Lawrence to Cascapedia on the Bay of Chaleur, passing through a country ?of which very little was known at that time. After a rather rough trip to the headwaters of the Grand Cascapedia river, Logan's party descended this river to its mouth, passing ten miles west of what is now known as the Federal mines. There is no record of Logan, or of any of his party, finding zinc or lead ores of any character on their journey across the peninsula, and until 1909 no precious or base metals were discovered within reasonable distance of Logan's survey.

Jan 1, 1924

By J. W. Craig

CHROME ore, which is used in Canada in the production of ferro-alloys, in a variety of refractories, and indirectly in many chemical industries, is both commercially important and scientifically interesting. The sight of chromium metal is familiar to all of us in the home, the office, the automobile. Chromium is synonymous with armaments: it is understood to be one of several essential metals in tanks, which played an important role in the defeat of France in the spring of 1940. Chromium, in other forms, comes into our daily lives by way of paint and leather, of the familiar green ginger-ale and beer bottles, and more indirectly in every pound of steel produced in the .Dominion. Necessary to our civilization in peace and war, the ores of chromium occur in many corners of the earth. This paper attempts to describe the chemical constitution of chrome ores, their world distribution, and the various chrome products and their industrial applications in Canada.

Jan 1, 1940

By M. R. Hegge

The Jabiluka One and Two uranium deposits occur in Lower Proterozoic metasediments of the Cahill Formation, which is part of the Pine Creek Geosyncline in the East Alligator River area, Nothern Territory. The Jabiluka One deposit coincides with a "window" through unconformably overlying Middle Proterozoic sandstone of the Kombolgie Formation; Jabiluka Two is completely covered by that sandstone. The observed part of the Cahill Formation exhibits four horizons which are favourable hosts for uranium mineralization. These have been folded into an east-southeast-striking, gently plunging, open asymmetric syncline-anticline structure. The host rocks are mainly chlorite and/or graphite schists and their brecciated equivalents which have undergone initial regional prograde metamorphism to the amphibolite facies, then retrograde metamorphism to the greenschist facies. Mineralization consists of pitchblende, mainly filling open spaces and to a lesser extent in disseminated form. Chlorite, pyrite and quartz are commonly associated with the uranium mineralization. A portion of the Jabiluka Two deposit contains economic concentrations of gold. Structural preparation with low-pressure conditions at these sites appears to be the most significant ore control. Genetic hypotheses favour initial deposition in Lower Proterozoic sediments, followed by remobilization during later orogenic events. The deposits bear a marked similarity to some pitchblende deposits in central Canada.

Jan 1, 1977

By Cesar Carrasco

Mine reconciliation is the art and science of comparing predictions and real-world outcomes with the intent of revealing the true quality of performance of models, planning, mining, and mineral processing. When mine reconciliation is conducted in a systematic, transparent and sustainable way it can play a central role in the governance of Mineral Resource and Mineral Reserve (MRMR) estimation and reporting. The core processes of modelling, planning, mining, and processing need to be transparent to be able to demonstrate that MRMR are reliable predictors of mine performance and value. Transparency is also necessary for mine technical staff to generate meaningful analyses, conclusions, and business improvement actions that demonstrably maximise value for all stakeholders. Most mines have some form of mine reconciliation practice, however because there is no agreed industry standard, and because mine reconciliation is difficult for a variety of reasons, it is often unsustained and/or ineffective at delivering the required transparency of performance. To deliver true governance of MRMR and business value, mine reconciliation must be sustainable. There are two categories of issues that combine to make mine reconciliation extremely difficult to sustain, these are technical, and people related. Technical issues include defining standard terms, accurately tracking material flows, data availability/adequacy/quality, calculation of key performance indicators and tolerance limits, analysis, and interpretation of results, understanding limitations of modelling techniques, and defining appropriate actions that can deliver value. These technical challenges are non-trivial, however compounding these are a range of people issues that include personal agendas, scepticism, lack of knowledge and experience, poor teamwork, absent leadership, toxic workplace culture, staff turnover, ineffective communication, siloed organisational structure, and lack of deliberate change management. All these problems can be solved with clarity of purpose, definition of the process of mine reconciliation, discipline in following the process, appropriate resourcing, and commitment to success across the entire organisation. Outlined in this paper is a management system that delivers sustainable mine reconciliation by addressing both the technical and people issues described above. This approach can deliver significant value for a mine and adds a robust, defensible governance over MRMR estimation and reporting.

Oct 1, 2024

By J. Xie

In underground coal mining, the potential for an outburst of coal and gas is considered to be one of the major hazards. As such, considerable emphasis is given to understanding and preventing such events. A number of indices are used in the prediction of the outburst in a coal mine. The main indices include initial gas desorption rate, gas pressure, gas content, coal strength, gas flowrate from a borehole drilled in a coal seam, and combinations of the above. Some of these indices are considered to be inadequate, inappropriate or impractical for some coal seam conditions, such as those with soft and friable coal. The Huainan Mining Group (Huainan) in China and the Commonwealth Scientific and Industrial Research Organisation (CSIRO) in Australia have been jointly developing gas content based technologies to predict the risk of the outbursts. One of the major progressive achievements is a new method for determination of outburst gas content threshold values. The method utilizes empirical analyses, numerical modeling, and seam-specific knowledge . This paper describes the method and its application for the #11 Seam at Guqiao mine, Huainan.

Aug 1, 2013

By G. E. Wood

THE INSTABILITY of copper prices and their low levels since late 1974 are of great concern to both producers and, to a lesser degree, consumers of copper. The price levels portrayed by the "neutral long-term" price trend are assumed to have been enough to encourage sufficient investment to provide adequate world production capacity and yet not so high as to encourage development of excessive over capacity. The identification of the present level of this trend has taken on special importance for governments and for corporations active in the world copper industry. One approach to the possible determination of such a price is through the use of moving averages. In this way, the effects of relatively short-term price movements can be dampened, as can those related to business cycles. From such averaged price data, long-term trends can be sought over a selected time period. The choice of the past time period for which a price trend is sought may have a major effect on the result'. For example, in the period 1885-1973, the long-term price trend for copper in constant dollars showed a decline, whereas in the period 1919-1973 it was rising. For the purposes of discussion, an appropriate choice of period might be a relatively short and recent one so that the majority of the present cost factors would be present throughout. It should also be long enough to cover a number of full business cycles.

Jan 1, 1977

By T. Crivits

"Phase equilibria in the ‘Cu2O’-‘Fe2O3’-SiO2 system, the base slag system in copper production, were recently determined. However, the addition of MgO, commonly present in the slag, drastically changes the phase equilibria in this system. The present study focuses on the phase equilibria in the ‘Cu2O’-‘Fe2O3’-MgO-SiO2 system in equilibrium with metallic copper.Recently, an experimental procedure has been developed that resolved a number of experimental difficulties. This procedure has been successfully applied to characterise several complex industrial copper slags. It includes a high-temperature equilibration followed by rapid quenching and electron probe X-ray micro-analysis (EPMA). The methodology was adapted to the present system and used to determine the liquidus at SiO2 saturation and in contact with high-MgO phases in between 1100 and 1250 °C in Cu2Orich slags.The results indicate a maximum solubility of MgO in the system at 1200 °C of 5 wt%. The boundary line between tridymite and spinel lies 3-4 wt% closer to the SiO2 apex for every 2 wt% MgO added. These new data on the high-copper slags are important for optimisation of the direct-to blister"

Jan 1, 2014

By M. Mirzazadeh

Air cooled crackable and conventional forged steel specimens were tested under reversed push-pull conditions to examine the effect of shot-peening on their high cycle fatigue behaviour (-106 cycles). The steels were tested in the normalized as well as shot-peened conditions. The results showed that shot-peening smooth specimens had little effect on the fatigue limit of the air cooled forged steels and the detrimental effect of the rougher peened surface was not apparent. Microhardness profiles indicated that the shot peening produced a gradient of compressive residual stresses that was greater than that of the loading stresses, suppressing the anticipated beneficial effect on fatigue life. Crack initiation was more likely to occur below the surface. The results indicate that the surface roughness was not a significant factor in controlling the fatigue lives, since they were essentially the same for the non shot-peened and shot-peened steels.

Jan 1, 2010

By H. Salomon-de-Friedberg

The amount of pyrite in copper concentrates fed to the CESL Process can vary appreciably. The fraction of pyrite that oxidizes influences both capital and operating costs and is therefore an important variable. The present paper explores operating conditions that influence the extent of pyrite oxidation and the probable overall reaction chemistry under CESL conditions.

Jan 1, 2014

By L. C. Johnston, J. N. Gills

This paper reviews the basic reactions of the blast furnace and the open hearth furnace, and then discusses the quarrying and sizing requirements of the limestone feed for each. Particular emphasis is placed on the lime-stone at Irish Cove, now being mined under an agreement between Scotia Limestone Limited and Dosco Steel Limited. The drilling and blasting operations are described, along with loading and haulage, plant flow, water supply, power supply and transportation facilities.

Jan 1, 1967

By Lan Vu

"The Ferderber mine consists of a series of Archean gold-bearing quartz lenses within a shear zone that crosscuts the central part of the quartz diorite Bourlamaque batholith. This zone has sharp contacts with the enclosing quartz diorite, and on average strikes N70E and dips 65SE. Along the contact with the shear zone, the quartz diorite is chloritized, sericitized and carbonatized. The chlorite schist within the zone is probably derived from mafic dykes.The geometry and distribution of structural features within the Ferderber shear zone suggest a long history of repeated movements. The majority of gold-bearing lenses were first emplaced during a probable early period of brittle shear which resulted from strike-slip movement. They were then folded and pulled into boudins by a later episode of reverse movement that accompanied ductile shear. New mineralized veins were emplaced in the shear zone and deformed at this time.Mineralized veins are dominated by quartz, carbonates, tourmaline and micas. Gold is more common within pyrite where chalcopyrite is abundant and is generally in contact with both pyrite and chalcopyrite at ""triple point"" grain junctions. This intimate association suggests that copper may have played an important role in gold deposition.Recent exploration has shown that the Bourlamaque batholith is cut by many parallel or en echelon shear zones. Study of ""Landsat"" and aerial photographs has indicated a number of linear structures striking ENE-WSW and ESE-WNW which form a conjugate system. The intersection of these two structural trends presents an interesting exploration target."

Jan 1, 1990

By E. Barsky

"Theoretical notions of mass transfer processes in cascade separation of bulk materials have not been adequately developed as yet (Barsky M.D. 1980). In this paper we have derived linear difference equation of the second order for a cascade with initial feeding top any stage proceeding from mass exchange regularities. The solution of these equations has allowed us to determine quantitative dependences of the material distribution over the cascade stages, which serve the basis of the method of predictive estimate of the process results. We have also examined the model of the material distribution coefficient formation at individual cascade stages.We have checked the adequacy of this model to experimental data. It is noteworthy that the obtained theoretical results are phenomenological, i.e. they can be applied to the processes of separation of different physical nature, e.g. of isotopes, liquid media, gases, etc.INTRODUCTIONRecently, the processes of cascade separation of bulk materials have found broad application in various industries. They ensure a high separation efficiency and high-quality composition of final products. Although specialized literature gives serious attention to cascade processes [1], their theory is not sufficiently developed yet. To achieve optimal organization of this process, we examine mass transfer in a cascade gravitational classifier with stages of identical design."

Jan 1, 2016

By R. Siwik, N. K. Davé

"The national reactive tailings (RATS) program is a co-operative industry-government effort to develop practical techniques for closure of reactive tailings areas. This paper summarizes the RATS program objectives and areas of research, and details the Noranda/CANMET project on the Waite Amulet tailings.Geophysical and biohydrogeochemical investigations were carried out at an inactive copper-zinc mine tailings site, Waite Amulet, in Noranda, Quebec. Geophysical investigations consisted of seismic, electromagnetic conductivity and electrical resistivity surveys to determine the thickness of the layers above bedrock and to map conductivity variations within the tailings and the immediate outlying area. Biohydrogeochemical investigations consisted of installing multilevel piezometer nests to determine groundwater flow patterns and porewater chemistry, obtaining solid core samples and characterizing for physical, chemical and mineralogical parameters, and iron oxidizing and sulphate reducing bacterial counts.The geophysical survey indicated a bedrock ridge extending under the tailings from the northeastern outcrop which may act as a porewater boundary layer. The survey also indicated a 2 to 20 m clay layer underlying the main tailings dam. Preliminary results of the saturated zone porewater chemistry have indicated three major zones of high electrical conductivity varying between 1,000 to 12,000 µs and pH between 3.4 to 8. Lower pH and high metal and sulphate concentrations were obtained in a shallow zone near the water table. With depth, the concentration of metal and sulphate ions decreased and pH increased below the water table. The underlying clay layer is relatively impervious -and most of the seepage from the tailings is probably exiting from the sides of the impoundment dam."

Jan 1, 1987

By C. H. Knight

"THE OBSERVATIONS that follow are confined to simple wet cyclones such as the cylindro-conical unit developed by the Dutch States Mines and marketed in America under the trademark 'Dorr-Clone'. Energy to do the work comes from the inlet velocity of the feed slurry, which is usually pumped' to the unit by a centrifugal pump.Such cyclones are simply classifiers of enormous capacity and depend for their separating effect on differences in rates of particle settlement. These particle settling rates, of course, vary with particle size, particle density, particle shape, pulp viscosity, and pulp density.The dilution of the overflow product affects both pulp viscosity and pulp density. In most operations, the temperature and the composition of the liquid -hence its viscosity --are fixed, but both pulp viscosity and pulp density can be changed by changing pulp dilution.Since the separating effect depends on differences in rates of particle setting, a perfect split with 100 per cent of the particles coarser than a given size in the underflow and 100 per cent of the finer sizes in the overflow is not possible. Just how far the separation departs from this perfection can be calculated rather exactly from the following principles, which also apply to mechanical classifiers. In removing or settling out of the overflow product all particles up to a specified size, some of the finer particles must settle out simultaneously."

Jan 1, 1955

By John J. Laffin

"Nova Scotia Department of Mines and Energy Throughout the history of Nova Scotia, trends in the production and use of its coal resources have resulted in major impacts on the economy and society of the province. Current trends in coal demand locally, nationally and internationally are having and will have an increasing positive effect on Nova Scotia over the next twenty years-in terms of energy supply, job creation and general economic development. Coal for electrical generation is an immediate and key objective of Nova Scotia's energy plan; and, in the long term, coal-derived fuels will meet the province's needs for transportation fuels. Demand for metallurgical coal is also expected to increase, especially if the merchant coke plant currently under investigation becomes a reality.Meeting these coal supply and utilization objectives in the face of increasing environmental, social and economic constraints poses a tremendous technical challenge. Work has begun on projects to expand coal production capacity and to adapt new technologies for coal preparation and utilization to the specific needs of Nova Scotia; much more work will be required in the coming decade in order to succesfully tap this resource.IntroductionThe energy problem facing Atlantic Canada has a few unique features not found in the rest of the country. Canada, as a whole, has access to a diverse mix of energy resources, including crude oil, natural gas, coal, hydro and uranium, with the result that crude oil supplies only about 40 per cent of Canada's primary demand. In contrast, foreign crude oil dominates Atlantic Canada's energy mix, supplying over 70 per cent of the primary energy demand.This results in important differences in various sectors. Nationally, about 5 per cent of the electricity is generated from oil whereas last year in Nova Scotia approximately 40 per cent of the electricity generated was from imported oil. Residential, commercial and industrial space heating, and industrial process heating in Atlantic Canada was almost 100 percent dependent on foreign oil. This is in sharp contrast to the situation in central and western Canada, which have access to secure domestic natural gas, oil and hydro electricity."

Jan 1, 1982

By C. Prévost, V. Leclerc, R. Pinto, M. Ruel

"A buffer’s ability to dampen production variations is directly related to its size. Small buffers cannot handle large variations in production, resulting in production losses when their inventory is depleted or saturated. This paper presents a predictive control algorithm used to regulate the inventory in a buffer of limited size, subject to large production variations caused by an upstream batch process. The algorithm was designed to manage the acid flow rates in an acid regeneration process, servicing batch leach reactors at Rio Tinto Fer et Titane, in Sorel-Tracy, Québec. The objective was to increase production by reducing equipment downtime caused by imbalances in the acid tanks servicing the leach reactors. The controller attempts to maintain acceptable acid tank volumes by optimizing the leach reactors acid/slag ratio and reaction time as a function of anticipated acid needs, all while maintaining product quality.INTRODUCTION Some beneficiation processes in extractive metallurgy require processing bulk material in batches. Typical examples of metallurgical beneficiation batch processes are smelting, leaching, electrowinning, elution and carbon-in-pulp. These processes are often situated midstream in an ore beneficiation flow sheet and either receive or transfer ore to continuous processes. Batch processes, by their very nature, introduce large variability in the flow sheet, because they process large finite quantities of material at nearly periodic time intervals. In order to dampen variations in production, various buffers–tanks and stockpiles–are utilized to accumulate ore upstream and downstream of batch processes. A buffer’s ability to dampen production variations is directly related to its size (Phillis & Gumede, 2011). Small buffers cannot handle large production variations, resulting in equipment downtime when their inventory is depleted or saturated (Everett, 2010, Berton et al., 2013). Consequently, the batch equipment production rates must be adequately managed to minimize production losses, attributed to depleted or saturated inventories, while maintaining product quality. Algorithms that anticipate or predict future production variations are often utilized to regulate buffer inventories, subject to large flow rate variations (Salvo et al., 2002; Bonvin, 2013). This paper presents a predictive control algorithm used to maintain an acceptable volume in a spent acid tank servicing several batch leach reactors. The algorithm is implemented at the acid leach plant of Rio Tinto Fer et Titane, in Sorel-Tracy, Québec."

Jan 1, 2017

By S. Esfahani, M. Barati, K. Danaei

"Substituting Portland cement with slag cement is one of the most economically attractive uses of slags. For this application, high cooling rates are required to form an amorphous structure. However, this is counteracted by the need to use small coolant flowrate to allow recovery of slag thermal energy as high quality heat to the coolant fluid. Therefore, a relationship between cooling rate of slag and its structure is essential to recover the heat effectively while making an amorphous slag.A modified Single Hot Thermocouple Technique (SHTT) was employed to investigate the crystallization behavior of slags by plotting their TTT (Time-Temperature, Transformation) diagrams. Seven different slag compositions containing CaO, SiO2, Al2O3, MgO were prepared at varying basicity (CaO/SiO2 =0.5-1.4).The results indicate that with increasing basicity, the TTT curves of glassy to crystalline transformation shift to the left which means higher crystallization tendency. This agrees with the fact that with the increase of basicity, the Si-O bonds are weakened, which in turn facilitates the re-ordering and crystallization of the silicate structure."

Jan 1, 2014