Search Documents

By C K. Bell, L. S. Collett

An AFMAG survey was flown in 1968 over the Upper Nelson River area, Manitoba. The flight direction was northwest-southeast and flight spacing was 2 miles. In the Cross Lake Subprovince, AFMAG showed that an isolated peridotite outcrop was part of a dike that extended over 80 miles. Diabase dikes are not always marked by an anomaly, but isolated cross-overs, when used in conjunction with geological and magnetic data, permit their extrapolation. Anomalies coincide with areas of sulphide mineralization. In the Flin Fion Subprovince, known and unknown northeast-trending faults are detected. The Berry Creek fault was extended south through Tramping lake, then under the Paleozoic cover. Conductors were detected at, or near, the axes of major synclines within Amisk and Snow Group sediments. Granitic terranes have low conductivity and, because they are characterized by smooth AFMAG profiles, they can be delimited. AF.MAG is being recognized as a geophysical method that can aid geological mapping and interpretation. Its most important contribution to the geologist will be in regions where out-crops are sparse.

Jan 1, 1971

By H. G. Harper, R. C. Hart

"The Mississagi quartzite is the basal formation of the Quirke Lake trough. As it is traced around the rim, a gradual change in dip is observed, as follows:Northwest corner 50 degrees south.Algom Quirke mine 34 degrees south.Quirke Lake 25 degrees south.Whiskey Lake 22 degrees west.Pecors Lake 25 degrees north.Algom Nordic mine 18 degrees north.Elliot Lake 11 degrees north.Pistol Lake 5-7 degrees west.Thus the apparent synclinal axis is a curving east-west line lying closer to the north limb than to the south. The axis appears to plunge west at about 5 degrees.The Huronian sediments lie on a basement of granites, gabbros, and volcanics. Diamond drill evidence indicates that this basement has a surface of peneplanation, and that the areas of soft basic rock have a smoother topography than the granite. For the most part the orebodies at the Quirke and Nordic mines overlie a basement of soft basic rock.The Mississagi formation is the host rock of the deposits, and its primary structures are suggestive of the conditions under which the conglomerate beds were deposited. Cross-bedding is common, although normal bedding varies from thick to thin to essentially lacking. Grain gradation is not common. Where coarse and fine grains occur together, the coarse tend to be more rounded than the fine. These features are characteristic of shallow-water deposits, laid down above the lower limit of wave action. Therefore, the quartz-pebble conglomerates probably represent ancient water courses, bays, beaches, and bars.The causes governing the creation of the trough can only be conjectured, but there is evidence that both subsidence and compressive stresses played active roles. Drag-folds in argillite beds near Whiskey Lake indicate compressive stress. On the other hand, gentle crumpling in thin-bedded limestones on Quirke Lake is probably due to pre-induration slumping and folding. If strong compression had been widespread within the trough, one would expect drag-folding and shearing of the incompetent beds to be more general. Two large-scale, fold-like structures were mapped by Collins, but their axes do not parallel the trough axis, and they are therefore not related to the major structure."

Jan 1, 1949

By Stephen Hardcastle

Presentation Outline ? Introduction ? Mine Ventilation Facts ? Ventilation-on-demand (VOD) ? Sensors/Controls ? Continuing Work ? Conclusions ? Mine ventilation engineering practices were published in 1556 in Agricola?s De Re Metallica (wind sails, bellows, etc.) That was then? This is today? Large fan installations handling >1M cfm

Nov 1, 2011

By R. Barbaroux, J. -M. Lalancette, D. Lemieux, K. Nasrallah, G. Garcia Curiel

"Arsenic released from the lithosphere by mining and metallurgical activities is a growing global environmental concern. Dundee sustainable technologies (“DST”) has developed a processing technology to sequester arsenic by means of vitrification. This method can effectively sequester arsenic trioxide without the need to oxidize from As (III) to As (V). Arsenic oxide is incorporated within a silica glass matrix that is stable as per the Toxicity Leaching Characteristic Procedure (“TCLP”) or EPA Method 1311. In this paper, the conventional treatment of arsenopyrite, commonly referred to as “two-stage roasting”, is discussed along with the options traditionally available for the remediation of the arsenic trioxide by-product. The drawbacks limiting the adoption of this processing flowsheet are discussed and a new processing route is presented for the treatment of arsenopyrite. This new flowsheet outputs an auriferous aluminosilicate highly amenable to gold extraction (> 96%) while eliminating the sulfur dioxide production associated with the second-stage roasting of pyrrhotite and ultimately uses vitrification as a definitive sequestration solution to arsenic trioxide.INTRODUCTION Faced with the depletion of conventional gold ores, the gold industry has witnessed a trend towards the exploitation of arsenical deposits. Arsenic is a naturally occurring metalloid often found in mineralogical association with gold. Many northern Canadian regions, from the Northwest Territories to Northern Manitoba, Northern Ontario and the Abitibi region are facing significant arsenic challenges. Projects are deemed uneconomic or prevented from going into operations due to the costs associated with handling arsenic material and there are penalties imposed to complex concentrates by smelters. In addition, Canadian mining operations have left an environmental legacy of gold tailings with grades typically of up to 9 grams per tonne with no processing solution as they also contain significant arsenic contamination at grades of up to 20%. Table 1 presents a list of Canadian deposits known to contain arsenic."

Jan 1, 2017

By M. Bélanger, H. -L. Jacob

"The province of Quebec has a strong tradition in industrial minerals. Ten commodities are produced and the annual total shipments have exceeded $600 million in recent years. Quebec is a world renowned producer of chrysotile, titanium slag, graphite, and ilmenite. Quebec is an important North American producer of mica, talc, and peat moss. This paper reviews the main minerals and commodities that have been the object of exploration or development in recent years, namely graphite, wollastonite, dolomite, and silica. Some of the leading projects concerning magnesium minerals and apatite-ilmenite are described. IntroductionQuebec has a strong tradition in industrial minerals. It goes back to the second half of the 19th century when the first graphite and apatite mines in the Gatineau area and asbestos mines in the Eastern Townships were opened. Since then, more than 25 commodities have been produced in Quebec, making industrial minerals an integral part of the Quebec mineral industry. Today, industrial minerals and building materials count for one third of the total mineral production in Quebec.Present industrial mineral production includes 10 commodities (Table 1). In the last five years, the value of industrial mineral shipments has varied between 500 and 700 millions dollars annually, which represents 20% to 25% of Quebec’s total mineral production. For many years, Quebec has been a major producer of chrysotile and titanium slag, the only producer in eastern North America of mica, graphite and ilmenite, and a leading Canadian producer of talc and peat moss. Quebec also produces, mainly for domestic markets, dolomite, limestone, salt and silica.Quebec’s industrial mineral sector has been quite active in the recent years. Exploration by government geologists and companies has led to the outlining of new deposits, some of which are now in production; others are currently being evaluated. Technical and economic studies are also underway to determine the feasibility of various development projects."

Jan 1, 1999

By M. H. Pettibone

Sohio Petroleum Company's new L-Bar uranium mill near Grants, New Mexico. refines 2722 kilograms of yellowcake daily from 1360 metric tons of ore produced at Sohio 's J.J. No. 1 mine and other nearby mines. This paper follows the ore from the mine through the various processing steps - semi-autogenous grinding, acid leaching , countercurrent decantation, solvent extraction , ammonium diuranate precipitation, washing and drying, and tailings disposal.

Jan 1, 1978

By A. Idegami, M. Imamura, S. Heguri, Y. Ozaki

"Nickel powder can be produced by the reduction of a nickel ammine complex solution by hydrogen at high temperature and pressure. To minimize the deposition of fine nickel on the surface of the reactor and other equipment, seed crystals are added to the initial solution to promote nucleation of the nickel powder. Such seed crystals catalyze the precipitation of the nickel particles on the surface of the seed and enhance grain growth. In this study, nickel nuclei were precipitated by the addition of a polymer to the nickel ammine complex solution, resulting in the production of nickel powder. Thus, we herein propose a model that explains the effect of the polymer in the precipitation of nickel nuclei.INTRODUCTIONNickel powder is commonly produced via a hydrometallurgical process from the hydrogen reduction of a solution containing a nickel ammine complex at high temperatures and pressures, and this process was commercialized in the 1950s by Sherritt Gordon (Sherritt International, Canada, Benson & Colvin,1973; The Staff, Research and Development Division, Sherritt Gordon Mines, Ltd., 1958).In the above transformation, upon the injection of hydrogen gas into the solution, nickel is reduced as outlined in Equation(1), ultimately resulting in the production of nickel powder.Ni(NH3)nSO4+ H2?Ni+ (NH4)2SO4+ (n-2)NH3(n:2–6)(1)In this process, seed crystals are added to the reactor to suppress the precipitation of fine nickel (scaling) and to enhance nickel reduction (Benson & Colvin, 1973; Mackiw, Lin & Kunda, 1957). More specifically, iron sulfate and a small amount of dispersant polymer are added, which leads to the formation of nuclei. Upon subsequent hydrogen reduction, the reduced nickel can then be deposited on the nuclei, allowing nickel particle growth to take place. However, this results in iron contamination in the final nickel product, and so the use of pure nickel as a seed crystal is desirable to produce high quality nickel powders."

Jan 1, 2017

By J. Bednar, R. R. Rogers, W. Dingley

"Zinc is by far the most important metal used for protecting steel from the ravages of corrosion, and cadmium is also used extensively for this purpose. These metals are applied by electrodeposition in cyanide baths when a particularly good appearance and high throwing power are required. One great disadvantage in using these baths has been the decrease in cyanide concentration and the increase in carbonate concentration that takes place during the plating. Another disadvantage has been the development of serious embrittlement in high-strength steels. The present authors have developed new cyanide baths for electroplating both zinc and cadmium on steel. These baths are stable in composition during plating, they have not produced appreciable embrittlement in the high-strength steels that have been investigated up to the present time, and they permit the use of considerably higher plating current densities. In addition, they produce extremely fine grained coatings that are attractive and have excellent adherence and covering properties. Brighteners can be used in the plating baths if bright finishes are required."

Jan 1, 1967

By C. O. Staples, J. G. Morrow

The application of cationic flotation to the upgrading of magnetic concentrates was investigated in the laboratory by both batch and continuous test procedures. It was found that the collection of coarse gangue particles with amine, heretofore considered a serious obstacle to this particular application of cationic flotation, is greatly enhanced by a drastic reduction in what might otherwise be considered normal impeller speed. Gangue flotation is in-dependent of variations in the rate of aeration. The collector and Crother additions and the impeller speed which favour the formation of a matte froth yield optimum results.

Jan 1, 1966

By J. E. Dutrizac, J. B. O'Reilly

"Zinc is a relatively abundant element which occurs as both high-grade sulphide ores {sphalerite ZnS) and oxide ores which the ancients collectively termed ""calamine"" (smithsonite ZnC03 and/ or hemimorphite Zn4Si201(0H)2 - H20 and/ or hydrozincite Zn5(C03) 2(0H)6). Although oxidic zinc is readily reduced by carbon, the process becomes thermodynamically viable only at - 1000°C, and at this temperature the zinc is released as a vapour (B.P. 907°C). Casual cooling of the vapour results in its re-oxidation by excess combustion air or even the carbon monoxide product of the reduction reaction. ZnO + C = C09,, + Zn vapom Only fairly rapid quenching of the zinc vapour and the isolation of the reduction products from the combustion gases will yield metallic zinc; these conditions were not produced deliberately until the advent of distillation technology. Until quite recently, the principal use of zinc was in brass manufacture; galvanized iron was not discovered until the 19th century and zinc casting alloys are a relatively recent invention. As will be seen, brass could be produced without recourse to a pure zinc intermediary, and the discovery of brass preceded that of zinc by many centuries. The purpose of this paper is to outline the discovery and early development of both zinc and brass with special reference to the European scene."

Jan 1, 1999

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to maximise health and safety performance in the mining industry through implementing continual improvement in management of major unwanted events. A comprehensive knowledge base has been captured for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This will be extended to outburst, coal burst and bumps, interface displays and controls, tailings dams and inrush in 2013. RISKGATE presents substantive and leading edge controls to assist industry stakeholders in the design, management and reporting of organisational and regulatory compliance requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry. All major Australian mining companies are contributing topic experts to this broad industry initiative. In the first 24 months, nine coal mining companies nominated over 80 different experts who contributed over 400 days of individual time to the knowledge capture workshops. RISKGATE is the largest single Australian Coal Association Research Program (ACARP) occupational health and safety (OHS) initiative to date.

Aug 1, 2013

By Karl J. C. Harries

"12.1. NO DEPRECIATION/GAAPAll calculations and computations relating to the Royalty shall be carried out in accordance with generally accepted accounting principles consistently applied to the extent that such principles are not inconsistent with the provisions of this Schedule and the agreement attached hereto, it being specifically agreed that nothing herein contained shall permit, or be construed to permit, the Operator to deduct any amount for depletion, depreciation, amortization or any deduction that represents a non-cash outlay.Comment: In cases like net profit royalties where recoupment of prior expenditures is permitted, care should be taken to avoid any implication that depreciation may also be taken. It is only logical and equitable that Property Owners should not be permitted an apparent ability to “double dip” with respect to deductions. A provision like this example should accomplish the task. It will be noted that the example specifically contemplates that the negotiated arrangements will prevail over any requirements of GAAP. Accordingly, if the parties agree to an unusual formula for recoupment, it will not be set aside to accommodate GAAP requirements. Under GAAP, revenues and expenditures are accounted for on an accrual basis. In addition, it specifically prohibits the taking of non-cash deductions, which is in keeping with the concept of recoupment.Although in some ways the example states the obvious and could be considered redundant, its presence, especially in provisions contemplating recoupment, makes it clear to the financial people that there may well be some variations from normal practices dictated by GAAP, while at the same time confirming the availability of GAAP to fill any voids.The accounting profession often makes the caveat that application of GAAP is an “art”, not a “science”. GAAP do not provide a cure-all and can create problems that will have to be addressed. For example, GAAP contemplate that asset costs are to be reduced by investment tax credits, which can cause a problem for a payor with more than one mine."

Jan 1, 2003

By J. Beddoes

Many high strength aerospace alloys undergo solution heat treatment (SHT) and aging to develop precipitate strengthening. Most simply, SHT involves an isothermal hold in a single phase region followed by relatively rapid cooling to develop a super-saturated solid solution from which precipitates form during aging. However, subsequent properties are sensitively dependent on the details of the SHT, which frequently also serves a homogenization function. Altering the details of the thermal cycle during SHT significantly improves the properties attained during aging, as presented by examples of SHT design for titanium aluminide intermetallics, polycrystalline and single crystal superalloys, and 7075 aluminum.

Jan 1, 2010

By J. Desroches, J. Burghardt, N. Whitney, B. Lecampion, A. Surdi, M. Houston, S. Stanchits

There is accepted evidence that multistage fracturing of horizontal wells in shale reservoirs results in significant production variation from perforation cluster to perforation cluster. In fact, only a fraction of the perforation clusters seem to contribute to production in many shale gas and shale oil plays. In many cases, the orientation of the lateral section of these wells is determined by lease boundaries rather than principal stress directions, and these often do not coincide. When horizontal wells are misaligned from the far-field principal stress directions, the fracture must reorient from the near-wellbore principal stress directions, which are aligned with the wellbore, to the far-field principal stress directions. The primary objective of this study is to learn how various completion designs influence the near-wellbore fracture geometry when such a misalignment exists. A secondary objective is to understand the influence of rock fabric features, such as mineralized natural fractures, on this reorientation process. To understand these effects, eight laboratory hydraulic fracturing tests were conducted using a true triaxial vessel with 914 mm × 762 mm × 762 mm samples of Niobrara shale. Several different completion designs were studied, including the use of fracture initiation slots with several different orientations and the use of perforations selectively located to encourage a smooth transition from the near- to far-wellbore region. The tests were carefully scaled as accurately as possible to provide insight into the field near-wellbore phenomena. Pressure and fluid flux at the wellbore, deformation of the block, acoustic velocity, and induced acoustic emissions were acquired during the tests. Additionally, sized particles were also injected to gauge the fracture width away from the wellbore. After the test, the blocks were dismantled, and the fracture geometry was mapped in 3D. These measurements allow one to clearly differentiate the fracture initiation and the breakdown—meaning the peak pressure—to be clearly differentiated; the fracture was already well developed when the maximum pressure was reached. The study reveals non-negligible tortuosity and aperture restriction in the near-wellbore region. In the field, this would translate to high treating pressures, uneven proppant distribution, and possibly near-wellbore screenouts. The test results show that, of the configurations tested, the best approach is to use deep slots that are aligned with the far-field principal stress directions. The oriented perforation design did not achieve the simple, smooth transition that was hoped for, and instead produced multiple competing near-wellbore fractures and considerable tortuosity. The study also demonstrated that the presence of planes of weakness, such as mineralized natural fractures, near the slot tip can result in poor near-wellbore fracture geometries, even for the best completion configuration. We conclude from these tests that the misalignment of the well with a principal stress direction creates near-wellbore complexity that, in turn, creates uncertainty in proppant distribution and, therefore, production; proppant might avoid up to a half of the created fracture. Regardless of the wellbore orientation, this uncertainty is further increased by the presence of mineralized features in the rock fabric that can strongly alter or stop the growth of the hydraulic fracture. Preventing those effects by changing the completion alone proves difficult, and new strategies are required to ensure a reliable stimulation of shales.

Jan 1, 2015

By Anthony J. Deevy

"Abstract -The Magino gold mine is located 45 km northeast of Wawa, Ontario. There was limit­ ed gold production in the Iate thirties. The present operation was officially opened in October 1988 and produced gold until September 1992. It was a 635 tonnes per day, decline-accessed mine, with ore coming from several small blast hole and shrinkage stopes.The host for the gold is the Webb Lake granodiorite stock which was intruded into the Goudreau Lake Deformation Zone. This east-northeast-striking deformation zone overprints the generally east­ west-striking isoclinally folded metavolcanic and metasedimentary rocks, which make up the east end of the Michipicoten greenstone belt. The ore-shoots are controlled by dextral delatancy associated with the Goudreau Lake Deformation Zone. Shearing, bleaching and silicification accompanied the gold emplacement."

Jan 1, 1994

The Cadia mine is shifting from the open pit operation to the Cadia East underground block cave. The resulting increase in milled tonnes and the decrease in fines production through shifting to block caving require an increase of over 25% in installed power. This expansion is being accomplished via the installation of up-front crushing and HPGR milling of the ore, with the SAG mill receiving a secondary crushed feed. This design, criteria and rationale for selection is presented. Over the coming years, the mine will further expand capacity. The target is to accomplish this with minimal addition of installed power or use of fresh water. This presents a challenge that epitomizes the future constraints on our resource dependent and intensive industry. The approach and proposed options to this longer-term expansion are also presented.

Jan 1, 2012

By P. C. Sui

Numerical investigation and parametric simulations of the coupled electrical conduction and mass diffusion in the GDL of a PEMFC are reported. The coupled transport is solved using a 2D, "under-the-rib" computational domain for the cathode GDL. The current density on the GDL/catalyst layer interface, which constitutes one of the boundary conditions for the GDL domain and reflects the activation overpotential in the catalyst layer and the ohmic loss in the membrane, is solved iteratively using a novel numerical algorithm. A parametric study is performed to investigate the effects on current density distribution of various operating conditions such as oxygen concentration and membrane resistance, and of design factors such as GDL geometry, anisotropic transport properties, and deformation under the land area. The results show that the current density distribution under the land area can be dominated by either electron transport or mass transport, depending on the operating regime.

Jan 1, 2005

By Gordon A. Irons, H. Y. Hwang

An impinging gas jet on a water surface was studied to understand momentum transfer in oxygen steelmaking. Depth, width and oscillation frequency of the jet cavity were measured and the splashes interpreted with Kelvin-Helmholtz instability and combined Rayleigh-Taylor and Kelvin-Helmholtz instability theory. A model to calculate separate gas and liquid velocities, applying the exact momentum boundary condition, is proposed.

Jan 1, 2004

By D. K. Uko

In the stretch-bend or bending-under-tension test, a strip is rigidly clamped and restrained at each end and bent by central transverse loading using a radiused punch: The strip deflection at failure has been used as a measure of formability for high-strength low-alloy (HSLA) steels by other investigators. In this work, a detailed study is made of strains developing during stretch bending of an 80,000-lbf/ in 2 (552 MPa) yield stress steel using different punch radii. It is shown that toward the end of the process, the bending strains at both the inner and outer surfaces are tensile and suddenly increase at a rapid and approximately equal rate. The strain ratio in the failure region departs significantly from plane strain , even using a large width-to-thickness ratio of about 10. The effective fracture strains appear to be independent of bend ratio (punch radius/thickness) and significantly below the fracture s train in simple tension. Metallographic and tensile data were obtained for the subject material and, for one bend ratio, the effects on stretch-bend parameters of annealing both on this material and a. carbon steel were compared.

Jan 1, 1977

By David R. Lentz

Abstract -At True Hill in southwestern New Brunswick, low-grade porphyry-style Bi-Sn-Mo greisen mineralization is associated with the cupola of an epizonal granite porphyry (granite) that also exhibits three episodes of brecciation. The first episode of brecciation is an in situ, 8 m to 10 m wide transitional zone of net-veined to coarse-grained "blocky" endogranitic mesobreccia that is chloritized and greisenized and hosts weak disseminated mineralization. ln a zone doser to the host rock­ granite contact, angular fine- to coarse-grained endogranitic mesobreccia with greisenized matrix is superimposed on the earlier transitional breccia. The latest episode is fault-controlled and consists of quartz- and chalcedony-hosted subangular to rounded fine-grained "pebble" mesobreccias that crosscut and brecciate the other breccia types, as well as the adjacent altered metasedimentary country rocks. The first two episodes of brecciation are magrnatic-hydrothermal in origin related to hydrofracturing of the granite carapace and are accompanied by greisenization and mineralization, whereas the post-mineralization, silica-hosted, "pebble" mesobreccias related to hydromagrnatic, low­ temperature fluid circulation and/or boiling along faults near the contact. These magmatic­ hydrothermal and hydromagmatic mesobreccias are similar to those associated with W-Mo-Bi porphyry-greisen mineralization at the Mount Pleasant deposit.

Jan 1, 1994