Search Documents

By Tony B. Szwilski

A short study has been made of the underground mining potential in the Plains region, the Province of Alberta, Canada. Particular reference is made to the possible application of longwall mining: Presently underground mining is limited to small scale room-and- pillar methods. The problems anticipated with large scale mining at shallow depths (30 m) are examined. Production factors based upon longwall retreat mining utilizing shield supports are also considered.

Jan 1, 1981

By J. L. Bray, S. T. Ross

The paper provides electrometallurgical data on the problem of germanium removal from zinc sulphate solutions. Germanium traces have caused much concern to the zinc refiner. Confirmatory evidence of interaction between germanium and cadmium is presented. Statistical analysis of data expands its significance and enhances its value. Further research is outlined. THE literature contains many references to the effects of trace amounts of germanium in the production of electrolytic zinc. One of the authors had experience with this troublesome element as early as 1917 at Trail, B. C. In 1929, Tainton and Clayton' reported that concentrations of as little as one part per million of germanium were sufficient to cause serious losses in current efficiency. Liddell2 reported that trace amounts of germanium cause marked lowering of the hydrogen overvoltage of electrolytic zinc cells, so that commercial production was impaired. Bray3 recorded the history of germanium in relation to electrolytic zinc production, noting that concentrations below 10 ppm have been found to yield low current efficiencies and copious hydrogen evolution. Koehler' stated that germanium "when present to the extent of a small fraction of one part per million per liter, causes serious evolution of hydrogen with a corresponding reduction in current efficiency." Recently, however, S. W. Ross" reported, from Risdon, Tasmania, that "in the course of leaching . .. dissolved traces of germanium... if not removed almost completely ... increase the reversion of cadmium during the filtration of the copper-cadmium precipitate and reduce the current efficiency during subsequent analysis." The copper-cadmium precipitate referred to is the residue from the zinc-dusting purification of zinc sulphate leach solutions. In the face of such conflicting testimony and with the increasing industrial importance of pure germanium and zinc it was decided to investigate the relationship between cadmium and germanium. Furthermore, other work by the authors showed certain discrepancies to exist in the theories of Tainton, et al. In the laboratory, without marked efficiency decreases, the authors have deposited zinc successfully from solutions containing as high as 1 g per liter of germanium. This could be done only when there was no cadmium present. Preliminary investigations of the suspected rela- tionships were carried out by means of emission spectrographic analysis using a beryllium internal standard. Several solutions containing 100 g per liter of zinc, as zinc sulphate, and 1 g per liter of cadmium, as cadmium chloride, were prepared. These concentrations were on the order of those obtained during a commercial low-acid leaching process. Varying concentrations of germanium were added to these solutions so that the range of 0.0000 to 0.5000 g per liter of germanium was covered. A 250 ml sample of each solution was agitated with 2.5 g of zinc dust for 30 min, filtered, and the filtrates were examined spectroscopically. Qualitative evidences of cadmium traces were found in those filtrates which originally contained above 10 ppm of germanium. Reliability of the analytical method did not permit quantitative investigations since cad-Table I. Current Efficiencies Obtained at 0.0000 and 1.5000 G per Liter Cadmium Concentrations Ge Concentrastion,* Cd Concentration,* EtBclenoy, G per Liter G per Llter Pot 0.0000 0.0000 84.270 0.0010 0.0000 94.849 0.0050 0.0000 92.649 0.0075 0.0000 94.039 0.0100 0.0000 96.084 0.0000 1.5000 93.460 0.0010 1.5000 95.158 0.0050 1.5000 92.148 0.0075 1.5000 91.260 0.0100 1.5000 84.546 • Cd and Ge concentrations shown are those existing before zinc-dust purification. mium determination in the concentrations present in zinc-dusted solutions lacks sufficient sensitivity for reproducible results. As a consequence of the inability of the investigators to obtain acceptable results through direct quantitative analysis, an indirect approach was devised. This indirect method involved a study of the current efficiency, in a model zinc cell, as a function of the concentrations of cadmium and germanium. Variables such as cell temperature, voltage, current density, anode spacing, relative electrode area, degree of agitation, cathode preparation technique, time, acid concentration, and solution volume were held constant. Fig. 1 shows the cell used. The current was fur-

Jan 1, 1952

By E. A. Gulbransen, K. F. Andrew

The gas-metal reactions of zirconium are very interesting. The metal is extremely stable at room temperature to reactions with the several gases present in air and the metal will stay bright indefinitely. However, at temperatures of several hundred degrees higher the metal reacts readily with oxygen, nitrogen and hydrogen. This behavior, in addition to the fact that zirconium is one of the higher melting point metals which might have high temperature applications under the proper conditions, resulted in the work reported in this communication. There are several factors which indicate that zirconium might have good oxidation resistance at elevated temperatures. These are: (1) the high melting point of approximately 1860°C, (2) the high melting point of the oxide of approximately 2675°C, (3) the high degree of thermodynamic stability of the oxide to chemical reaction and the low decomposition pressure of the oxide and (4) the possible formation of a continuous oxide film since the volume ratio of oxide to metal is greater than unity. The unfavorable factors are: (1) the metal reacts to form nitrides, hydrides and carbides, (2) the oxide is soluble at elevated temperatures in the metal and (3) the oxide ZrO2 undergoes crystal structure transformations at high temperature. The oxidation resistance of this metal is not only a question of the rate of film formation but is complicated by the fact that the oxide and other reaction products dissolve in the metal which in turn will affect the physical and mechanical properties of the metal. The protection of the metal to nitride formation must be considered separately from the oxide problem. One unfavorable factor is that the volume ratio of the nitride to the metal is about unity. This indicates that a discontinuous film might be formed. This paper will present measurements on the rates of reaction of the metal with O2, H2 and N2 over a wide temperature and pressure range. The reaction in high vacuum and the stability of the several compounds formed will be presented. The results are correlated with fundamental rate theory and with the physical and chemical structure of the metal and film. Literature Although many papers have been published on the chemical reactions of zirconium with various gases, comparatively few are concerned with the protective nature of the metal and its reactions at normal pressures. The studies in the pressure range below 0.01 mm of Hg gas pressure are largely of interest in the nature of the adsorption of gases by hot filaments in high vacuum apparatus. The reactions of zirconium in this pressure range have been reviewed by Fast8 and by RaynOr.27 In spite of certain differences of opinion as to the maximum adsorption temperatures for various gases, the low pressure range is qualitatively understood. Some of these papers will be mentioned briefly here. 1. LOW PRESSURE Ehrke and Slack' find that oxygen reacts above 885°C and hydrogen above 760°C. Nitrogen does not react up to a temperature of 1527°C. Fast9 on the other hand observes that oxygen is absorbed above 700°C and nitrogen at temperatures exceeding 1000°C. Hydrogen is absorbed from 300" to 400°C and liberated between 500" and 800°C. It is readsorbed at 862°C and released above 862°C. Hukagawa and Nambo22 find a rather complicated picture for the absorption of oxygen. A rapid initial absorption is found between 180" to 230°C. Further oxygen is not taken up until a temperature of 450°C is reached. The optimum temperature for complete absorption is 650" to 700°C. Nitrogen is found to be completely adsorbed at 600°C. However some of the gas is evolved at higher temperatures. Their data on the absorption of hydrogen indicate some of the gas is removed at 550°C. Guldner and Wooten17 in a study of the low pressure reactions of zirconium with various gases observed that the reaction with oxygen occurs at temperatures above 400°C and that the oxide is formed. The reactions with carbon monoxide and carbon dioxide occur rapidly at temperatures of about 800°C with the oxide and carbide being formed. Zirconium reacts at temperatures of 400°C slowly and at 800°C rapidly to form the nitride and with hydrogen and water at 300°C to form the hydride and a mixture of the oxide and hydride respectively. 2. NORMAL PRESSURE DeBoer and Fast3 in a study of the electrolysis of oxygen in zirconium find that the metal absorbs up to 40 at. pct of oxygen without forming a new phase. The solubility of nitrogen in the lattice has been studied by de Boer and Fast4 and Fast10 and is found to be considerable. At higher temperatures the oxide dissolves in the lattice at an appreciable rate according to Fast10 and the zirconium surface becomes active. De Boer and Fast4 and Hägg18 have studied the solubility of hydrogen and find that at room temperature the solubility corresponds to ZrH1.95 Desorption occurs on lowering the pressure. Hydrogen is stated to be more soluble in the ß-form and the

Jan 1, 1950

Open pit operators have found the dropball crane a great aid in cutting costs and hazards of secondary breakage. But a common problem in using the unit has been with the shock absorbing connection from the cable to the dropball itself. Blair Limestone Div. of Jones & Laughlin Steel Corp. has come up with a new connector to solve this problem and to save the time usually lost in frequent replacement of the cable slings, chains, or old tires hitherto used at this point. J&L personnel solved the problem by combining three ideas from other dropball crane owners. Their unit consists of two long U-bolts running through a heavy spring originally made for use on a vibrating screen. Heavy duty swivels attached to the bent ends of the U-bolts provide attachment points for the crane cable and the special chain to the dropball. Connection at the dropball is by an eyelet welded directly into the mass of steel, and a special alloy chain is connected to this with a clevis.

Nov 1, 1955

By J. O. Lewis

The operation of gas-condensate fields is comparatively new and involves physical principles with which the industry was not prcviously familiar. It has been necessary to devise methods for testing gas-condensate wells and to correlate laboratory and field data. In this paper new methods are advanced for interpreting well G.P.M.† tests whereby dilution by dry gas can be estimated and information supplied on revaporization of condensates by dry gas. Inaccuracies in well test data are discussed. Changes in flow rates can cause changes in the G.P.M. of the effluent and it may take some time for a well to become stabilized after an important change in flow rate. Retrograde tests as usually conducted cannot be directly compared with field G.P.M. data, because the retrograde tests usually include solution gas in the condensates, which are reported On the cumulative basis whereas field data (G.P.M.) usually report pentaneS PlUS on a rate or instantaneous basis. Introduction Though long known to physicists, the phenomena Of retrograde condensation became known to the oil and gas industry Only in recent years, when deeper drilling disclosed that the behavior of vapors under changing pressures was different in high-pressure reservoirs than under the low-pressure operations with which the industry was familiar. These deep, high-pressure reservoirs in which condensation and vaporization behaved inversely to the accustomed manner became known as "gas-distillate," or preferably "gas-condensate" fields. Partly to prevent precipitation and retention of liquids in the reservoir, but still more to prevent the waste of residue gas, the operation known as "recycling," or preferably "cycling," was instituted, in which the residue gas is reinjected into the reservoir, thus maintaining pressure and driving the wet gas to the producing wells. For lack of field experience to serve as a guide, the industry had to assume that theory and laboratory experiments could accurately forecast retrograde behaviors in operating these gas-condensate fields, but it is obvious that these assumptions should be checked at the first opportunities against actual field experience. To make such checks, it is necessary to accumulate a large quantity of reliable field data, but experience has shown that it is difficult to obtain reliable field data and that the laboratory data as usually presented are not in directly comparable form. The problems of correlation involve the complex phase behavior on the one hand, and a knowledge of field data and a visualization of underground conditions on the other hand. This paper is an approach from field experience, The purposes of this article are to discuss the sources of uncertainty in the data and to present methods of analyzing, interpreting and correlating laboratory and field data. Data mostly from lower Gulf Coast fields are presented, from which some conclusions can be derived, but better data from more sources than those available to the writer will be required before satisfactory answers to many questions can be obtained. This paper is presented to stimulate the analysis and publication of data from other fields, the reexamination of field and laboratory methods, and the taking of more complete and reliable field tests. For these purposes, the writer presents some speculations that otherwise would not be appropriate.

Jan 1, 1947

By J. O. Lewis

The operation of gas-condensate fields is comparatively new and involves physical principles with which the industry was not prcviously familiar. It has been necessary to devise methods for testing gas-condensate wells and to correlate laboratory and field data. In this paper new methods are advanced for interpreting well G.P.M.† tests whereby dilution by dry gas can be estimated and information supplied on revaporization of condensates by dry gas. Inaccuracies in well test data are discussed. Changes in flow rates can cause changes in the G.P.M. of the effluent and it may take some time for a well to become stabilized after an important change in flow rate. Retrograde tests as usually conducted cannot be directly compared with field G.P.M. data, because the retrograde tests usually include solution gas in the condensates, which are reported On the cumulative basis whereas field data (G.P.M.) usually report pentaneS PlUS on a rate or instantaneous basis. Introduction Though long known to physicists, the phenomena Of retrograde condensation became known to the oil and gas industry Only in recent years, when deeper drilling disclosed that the behavior of vapors under changing pressures was different in high-pressure reservoirs than under the low-pressure operations with which the industry was familiar. These deep, high-pressure reservoirs in which condensation and vaporization behaved inversely to the accustomed manner became known as "gas-distillate," or preferably "gas-condensate" fields. Partly to prevent precipitation and retention of liquids in the reservoir, but still more to prevent the waste of residue gas, the operation known as "recycling," or preferably "cycling," was instituted, in which the residue gas is reinjected into the reservoir, thus maintaining pressure and driving the wet gas to the producing wells. For lack of field experience to serve as a guide, the industry had to assume that theory and laboratory experiments could accurately forecast retrograde behaviors in operating these gas-condensate fields, but it is obvious that these assumptions should be checked at the first opportunities against actual field experience. To make such checks, it is necessary to accumulate a large quantity of reliable field data, but experience has shown that it is difficult to obtain reliable field data and that the laboratory data as usually presented are not in directly comparable form. The problems of correlation involve the complex phase behavior on the one hand, and a knowledge of field data and a visualization of underground conditions on the other hand. This paper is an approach from field experience, The purposes of this article are to discuss the sources of uncertainty in the data and to present methods of analyzing, interpreting and correlating laboratory and field data. Data mostly from lower Gulf Coast fields are presented, from which some conclusions can be derived, but better data from more sources than those available to the writer will be required before satisfactory answers to many questions can be obtained. This paper is presented to stimulate the analysis and publication of data from other fields, the reexamination of field and laboratory methods, and the taking of more complete and reliable field tests. For these purposes, the writer presents some speculations that otherwise would not be appropriate.

Jan 1, 1947

By Arthur Wade

The most important development in connection with the search for oil in Australia during 1940 was on the legislative side. Prior to 1939 legislative enactments in the various states with regard to prospecting for petroleum were such as to prohibit large-scale effort and to bar the major oil companies from operating. The preparation of the Wade Model Bill for the Commonwealth Government in 1939 and the acceptance of the Bill in principle by all States, has gone far to remove these obstacles. Amending Acts, largely based on the Alodel Bill, have now been passed by all States with the exception of New South Wales and Tasmania. In New South Wales an Amending Bill is being drafted, while the Govern-ment of Tasmania is preparing to introduce an Amending Bill provided there is any demand for it. Noteworthy developments followed immediately on the passing of these Amending Acts. The Shell Company (1)1 and the Superior Oil Company of California (2) too$ up large areas in Queensland and com-menced work during 1940. Caltex acquired a big tract of country in the Kimberley district of Western Australia (3) and has made application for an area in the Territory of Papua. An Australian company, The Phoenix Oil Extraction Co., has obtained a permit to prospect over an extensive area bordering the south coast of Western Australia (4). Other developments are foreshadowed. The Shell Company is making an intensive examination of its area in Queensland (I). Geological, geophysical and aerial surveys are in progress. Caltex has three geological parties in the held in Western Australia while Superior Oil Company of California has done some geological work in the interior of Queensland (2). None of these concerns envisages a drilling campaign in the near future. Much exploratory work is necessary. Further work has been done by the companies that were already operating in 1939, though an important Australian company - Oil Search—has abandoned the work of prospecting in Australia. This company has subleased its holdings, at North West Cape in Western Australia (;), to Caltex on a royalty basis. The company also maintains its holdings in, and connection with, the Australasian Petroleum Company Proprietary Limited, which is a combination of Standard Oil (New Jersey), Anglo-Iranian and Oil Search. This company is operating in the territories of Papua and New Guinea. Drilling Victoria.—Although a good deal of drilling was done in the LaBes Entrance Tertiary Basin of Victoria (7), no appreciable production of oil was obtained. In order to test the extent and possibilities of the oil-bearing sand in this region, the Commonwealth and State Governments jointly put down six scout boreholes to depths of between 1200 and I500 it. The results were nega tive. A deeper exploratory horehole put down by the Governments at Seacornbe, or 26

Jan 1, 1941

By Arthur Wade

The most important development in connection with the search for oil in Australia during 1940 was on the legislative side. Prior to 1939 legislative enactments in the various states with regard to prospecting for petroleum were such as to prohibit large-scale effort and to bar the major oil companies from operating. The preparation of the Wade Model Bill for the Commonwealth Government in 1939 and the acceptance of the Bill in principle by all States, has gone far to remove these obstacles. Amending Acts, largely based on the Alodel Bill, have now been passed by all States with the exception of New South Wales and Tasmania. In New South Wales an Amending Bill is being drafted, while the Govern-ment of Tasmania is preparing to introduce an Amending Bill provided there is any demand for it. Noteworthy developments followed immediately on the passing of these Amending Acts. The Shell Company (1)1 and the Superior Oil Company of California (2) too$ up large areas in Queensland and com-menced work during 1940. Caltex acquired a big tract of country in the Kimberley district of Western Australia (3) and has made application for an area in the Territory of Papua. An Australian company, The Phoenix Oil Extraction Co., has obtained a permit to prospect over an extensive area bordering the south coast of Western Australia (4). Other developments are foreshadowed. The Shell Company is making an intensive examination of its area in Queensland (I). Geological, geophysical and aerial surveys are in progress. Caltex has three geological parties in the held in Western Australia while Superior Oil Company of California has done some geological work in the interior of Queensland (2). None of these concerns envisages a drilling campaign in the near future. Much exploratory work is necessary. Further work has been done by the companies that were already operating in 1939, though an important Australian company - Oil Search—has abandoned the work of prospecting in Australia. This company has subleased its holdings, at North West Cape in Western Australia (;), to Caltex on a royalty basis. The company also maintains its holdings in, and connection with, the Australasian Petroleum Company Proprietary Limited, which is a combination of Standard Oil (New Jersey), Anglo-Iranian and Oil Search. This company is operating in the territories of Papua and New Guinea. Drilling Victoria.—Although a good deal of drilling was done in the LaBes Entrance Tertiary Basin of Victoria (7), no appreciable production of oil was obtained. In order to test the extent and possibilities of the oil-bearing sand in this region, the Commonwealth and State Governments jointly put down six scout boreholes to depths of between 1200 and I500 it. The results were nega tive. A deeper exploratory horehole put down by the Governments at Seacornbe, or 26

Jan 1, 1941

By J. S. Levine

A series of four displacement experiments has been run in a large alundum core. Flow potential distribution in each liquid phase was measured continuously through oil-wet and water-wet capillary barriers, using a null-point pressure balance, and saturated distribution was determined from electrical resistivity measurements. A method has been devised for calculating the effective (and relative) permeability to each phase at any time and at any point in the flow system for the transient displacement process. Relative permeability points have been calculated and average curves drawn for oil displacing water and water displacing oil. The values of dynamic capillary pressure have also been determined. Data have been substituted into the generalized Buckley-Leverett fractional flow equation and a comparison between actual and theoretical breakthrough recoveries is shown. Displacement experiments have been performed in the laboratory for many years in an effort to determine the effect of a number of parameters on multiphase flow in porous materials. In the literature of petroleum technology, Wyckoff and Botset' were among the first to develop the relative permeability concept and to show experimentally that oil, gas, and water can flow simultaneously through a porous medium in a precise way governed by certain fluid properties, by the relative saturation of each fluid, and by characteristics of the medium itself. Somewhat later, Leverett2 and Hassler, Brunner, and Deahl11 developed some theoretical concepts of capillary behavior in porous materials. The work of Buckley and Leverett3 presented a theoretical analysis of immiscible liquid displacement based on the equation of continuity and the Darcy equation for viscous flow of each fluid. Subsequent investigators attempting to verify the Buckley-Leverett equation have, in general, deliberately neglected the capillary pressure term or have performed experiments in such a manner that it could be neglected. Terwilliger, et al4 in 1951, obtained agreement between theory and experiment for the constant rate displacement of water by gas in a long vertical sand column. Rapoport and Leas5 have investigated the

Jan 1, 1955

By Evan Evans

WITH the expiration on April 30, 1941, of the agreement between the anthracite operators and the United Mine Workers of America, a new agreement was entered into, providing for a general wage increase of 7 1/2 per cent effective May 1, to be brought to a total of 10 per cent on Oct. 1. Contract rates were increased from the rates established under the agreement of September 1923, and hourly rates were raised above the agreement of May 1936 as modified from the eight-to seven-hour day in May 1937. The new rates are to be in force for the duration of the agreement, ending April 30, 1943.

Jan 1, 1942

By D. Turnbull, J. E. May

THE (110) [001] texture in silicon iron is of considerable interest both from the technological and scientific points of view. Its occurrence was reported more than 20 years ago.1-4 The texture develops by means of secondary re crystallizatjon5 and can be very strong, that is, greater than 90 pct alignment even thouh the primary re crystallization texture is weak or complex. This behavior is in contradistinction to the face-centered metals which develop their strong secondary recrystalliza-tion texture from a strong primary recrystalliza-tion texture.', The microstructural changes accompanying the (110) [001] texture formation in silicon iron are as follows: When properly prepared cold-rolled sheet (i.e., 0.015 in. thick) is annealed at about 800°C, primary recrystallization occurs and a fairly stable fine-grained primary recrystallized matrix of about 0.02-mm-diam grain size is produced. The material at this stage does not have the strong (110) [110] texture. As the temperature is raised to about 900°C, relatively large grains appear in the finegrained matrix and they grow at the expense of the smaller grains to many times the sheet thickness. In time the complete sample is consumed by these large grains. This process of the growth of relatively few grains (about one in 105 primary grains) at the expense of many grains is called secondary recrystallization. Since all the secondary grains are of essentially (110) [001.] orientation, the strong texture is developed by this secondary recrystallization process. Theories of the (110) [001] texture in polycrystal-line silicon iron have been proposed by Decker and Harker and by Dunn.Decker and Harker have shown that grains initially in the (110) [001] orientation will upon annealing after cold-rolling, re-crystallize back to the initial orientation. To account for the sharp texture in silicon iron they propose that (110) [001] grains become more highly strained than grains in other orientations and therefore recrystallize first. They are then the lowest energy grains and can consume their higher energy neighbors. Grains in orientations other than (110)

Jan 1, 1959

By D. K. Crampton

INTERNAL stress and season cracking in brass have been studied for many years and the technical literature contains many data on various phases of the subject. A résumé of the literature shows certain fairly well established points upon which various authors are mostly agreed: 1. Season cracking is primarily caused by the presence of relatively high internal stresses, or possibly in some cases by external stresses, or both. 2. A specific corrosion is also essential to season cracking: Certain agents, particularly mercurous salts, mercuric salts and ammonia salts; have such a specific corrosive effect. 3. The tendency to season crack under given conditions increases with increasing zinc content, brass containing less than 20 per cent zinc being relatively immune. 4. In alpha brass the season cracks are intercrystalline; in alphabeta brass they lie between the two constituents; and in beta brass they are transcrystalline. 5. The ordinary impurities or added elements in special brasses have little or no effect on the tendency to season crack. 6. Internal stresses can be eliminated, or at least reduced to a safe 'limit by annealing treatments at temperatures that do not produce visible microstructural changes or appreciable softening of the worked brasses. There are, however, some points in connection with the phenomenon of season cracking which have not been thoroughly investigated, or wherein different authors and investigators are not entirely in agreement. The investigations described in this paper were undertaken to determine: 1. The correlation between mercurous nitrate tests and actual season cracking on long-time atmospheric exposure. 2. The quantitative effect of type and degree of drawing operations on the intensity of internal stress and on the tendency to season crack in brass tubes. 3. The possibility of drawing high-brass tubes in such a manner as to prevent the occurrence of harmful stresses rather than to find a remedy for such stresses once having obtained them.

Jan 1, 1930

By Francis M. Walters

THE problem of making iron-manganese alloys of scientific purity is a rather difficult one. They cannot be prepared in air because of the readiness with which the metals oxidize at the temperature of melting; and they cannot be prepared in vacuum because of the, high vapor pressure-of- manganese. The very property of: manganese which permits it to be purified interferes with the utilization of the best method of making pure alloys. Accordingly, it is necessary to use a gas atmosphere which will not affect the-properties of the alloys. The gases available for the purposes are hydrogen; helium and argon. Nitrogen forms intermetallic compounds with manganese very readily. Hydrogen, while valuable as a deoxidizer and having the advantage of being comparatively cheap, is explosive over a wide range and, has a rather high thermal conductivity. Helium is reported as, costing little but is difficult to secure at a reasonable price and also has a conductivity nearly as high as hydrogen. Since argon has a sufficiently low thermal conductivity, it has been selected for use in one induction furnace for melting, under a controlled, gas atmosphere, in spite of its cost, which is so high (70 cents to $1.50 per cubic foot) that it must be stored and purified.. Such a gas atmosphere-as argon makes necessary the use of the, high-frequency induction method of heating. This involves, a non-metallic container for the gas; .which is most conveniently of fused quartz or glass. The next

Jan 1, 1929

By Joseph Kaye Wood

A metal is said to be overstrained when it is deformed beyond the elastic limit at a temperature well below the critical range, as in cold working. Quantitatively, overstrain might be considered as that part of the total elastic deformation of the piece of metal, left over after the external load is removed, that added to the permanent deformation due to plastic action will give the total permanent deformation. Ordinarily the effects of this phenomenon, which vary with the internal residual stress probably in accordance with Hooke's law, are more noticeable when the yield point of the metal is exceeded, but they probably also exist to a smaller degree when the load is just large enough to cause the least amount of permanent set. These effects, which we recognize as the result of overstrain, are as follows: 1. An apparent increase of the elastic limit in tension and a decrease of the elastic limit in compression, provided the external load is tensile. The reverse is true when the load is compressive. 2. An elastic after-effeet in which time and temperature are important factors. 3. A state of imperfect elasticity in which Hooke's straight line becomes slightly curved, giving rise to an hysteresis loop. 4. In addition to the apparent increase in the elastic limit, such properties as the hardness, ultimate strength, and resistance to fatigue failure are increased, provided the overstraining has not been carried far enough to make the metal brittle. 5. Correspondingly the ultimate elongation, reduction in area, magnetic quality, ratio of endurance limit (fatigue breaking stress) to elastic limit, and resistance to season cracking (in certain copper alloys) are decreased. The question naturally arises: how do these changes in the properties of a metal resulting from overstrain influence our method of design? The fact that most of the desirable qualities are increased makes overstraining a favorable process, from an engineering standpoint; but on the other hand, the loss of such qualities as perfect elasticity and complete

Jan 1, 1924

By F. X. Tartaron

F. C. Bond (Consulting Engineer, Processing Machinery Dept., Allis-Chalmers Manufacturing Co., Milwaukee, Wis.) — Papers such as this one which deal in a lucid manner with the obscure fundamentals of comminution theory are always welcome. The author has attempted to bring together several diverse theories and handles them interestingly. However, some of the ideas expressed and conclusions drawn require critical reviewing, for which amenities alone will not suffice. The author points out that the theoretical energy required to break across crystal lattices is of the order of 1000 times the actual energy required to crush or grind, and that this energy in turn is perhaps 1000 times the measured surface energy of the new surface area produced. The energy required to grind commercially is controlled by flaws and dislocations, rather than by the inner strength of the lattice structure. The measured surface energy is only a slight residue left after the face atoms are adjusted to their new environment. The dislocations in the crystal lattice structure, with a spacing of about O.l,u, or

Jan 1, 1962

By C. B. Thwing

IT is likely that among most races, owing to the ease of finding and working clay, the making of clay utensils was learned earlier than the molding of metal implements. The ancients made good pottery and durable brick in kilns that wasted fully one-half the heat and spoiled fully one-fourth of the ware; and, taking the clayworking industry as a whole, we are doing the same today. The chemical and physical changes involved in the burning of clay are so many and vary so much with the composition of the clay that it is not surprising that the rule-of-thumb methods so commonly employed fail to give uniform results. In its passage from plastic clay to the vitreous or stonelike character the mingled minerals and accidental organic impurities of which the clay is blended must pass through four stages, the second and third usually overlapping, and the fourth often beginning before the third is complete. These stages in their order with the rising temperature are drying, dehydration, oxidation, vitrification. In the first part of the drying stage, usually accomplished in part outside the kiln, the water mixed with clay is dried out at temperatures not much exceeding the boiling point of water. In the later part of this stage, within the kiln, the hygroscopic water, absorbed from the air is expelled at somewhat higher temperatures, this stage being known as watersmoking. Some clays are very sensitive to temperature during the drying stage and if the temperature exceeds 100°, the ware becomes checked. Other clays may be dried more rapidly without danger. In down-draft kilns, the draft is slight during the watersmoking stage and the water driven off from the top rows condenses on the ware in the bottom of the kiln, with the result that high temperatures are likely to be reached at the top of the kiln before the bottom is fully dry. The lag in temperature of the bottom persists to the second stage in spite of the better draft then prevailing.

Jan 9, 1919

By Leon H. Nelson

Several factors which affect the segregation and solidification of killed hot-topped steel ingots are: (1) pouring temperature, (2) volume in the hot top, (3) taper in the ingot, (4) pouring rate by varying the nozzle size, (5) segregation of several elements, (6) moving ingots before completely solidified. In most of this discussion, segregation will be measured in terms of carbon variation only. All the data given are results on S.A.E. 1040 analysis of fully killed steel direct-poured in hot-topped molds giving 20-in, square ingots. Thus the variables of analysis and ingot size and contour are eliminated. Segregation results are all on the rolled-bloom size, not on the ingot itself. They are results from plant-control work and not results of special research on ingot segregation. Pouring Temperature The temperature (or, more correctly, the amount of superheat above the liquidus-solidus) of the steel entering the ingot is, of course, one of the most important factors influencing segregation and solidification. Table 1 gives the average segregation of a number of heats of S.A.E. 1040 steel with normal pouring temperatures of 2775" to 2825" F. The table also gives some data on segregation in hot heats (pouring temperature 2840" to 2870" F.) and in cold heats with some skull (poured at 2725" to 2760" F.). The results in Table 1 are on steel ingots with 20-in. square cross section and 60 in. long to the hot top. The ingot weighs 7100 lb. and the hot top contains 14.3 per cent of the total ingot volume and 11.2 per cent of the total ingot weight. The results are from drillings after rolling the ingots to bloom size. Segregation results obtained on the bloom are probably not as great as they would be in the ingot itself, since heating the ingots for rolling can perhaps cause some migration of carbon from regions of high and low carbon to those of average carbon content.

Jan 1, 1937

By D. K. Crampton

Internal stress and season cracking in brass have been studied for many years and the technical literature contains many data on various phases of the subject. A resume of the literature shows certain fairly well established points upon which various authors are mostly agreed: 1. Season cracking is primarily caused by the presence of relatively high internal stresses, or possibly in some cases by external stresses, or both. 2. A specific corrosion is also essential to season cracking. Certain agents, particularly mercurous salts, mercuric salts and ammonia salts, have such a specific corrosive effect. 3. The tendency to season crack under given conditions increases with increasing zinc content, brass containing less than 20 per cent. zinc being relatively immune. 4. In alpha brass the season cracks are intercrystalline; in alpha-beta brass they lie between the two constituents; and in beta brass they are transcrystalline. 5. The ordinary impurities or added elements in special brasses have little or no effect on the tendency to season crack. 6. Internal stresses can be eliminated, or at least reduced to a safe limit by annealing treatments at temperatures that do not produce visible microstructural changes or appreciable softening of the worked brasses. There are, however, some points in connection with the phenomenon of season cracking which have not been thoroughly investigated, or wherein different authors and investigators are not entirely in agreement. The investigations described in this paper were undertaken to determine: 1. The correlation between mercurous nitrate tests and actual season cracking on long-time atmospheric exposure. 2. The quantitative effect of type and degree of drawing operations on the intensity of internal stress and on the tendency to season crack in brass tubes. 3. The possibility of drawing high-brass tubes in such a manner as to prevent the occurrence of harmful stresses rather than to find a remedy for such stresses once having obtained them.

Jan 1, 1930

By D. H. Polonis, M. B. Kasen

AN unusual thermal etching phenomenon has been observed on the surface of a Cu-Si alloy. The observations were made during studies of vacancy condensation pit formation which were reported in previous papers.1,2 Figs. 1 and 2 are photomicrographs of the surface of a Cu-4.8 pct Si alloy after heating in vacuo (3 x X mm Hg) to 525°C and subsequently holding at that temperature for 16 hr in an impure (air-contaminated) argon atmosphere. Under these conditions preferential removal of silicon from the matrix by oxidation results in a surface which is entirely a phase overlying an a plus y structure. The light areas of Fig. 1 are regions in which very little thermal etching has occurred, while the majority of the surface has experienced severe etching. Similar regions in Fig. 2 are seen as plateaus above contours produced by net transfer of material from the specimen surface. Twin boundaries are also visible in Fig. 2. The difference in matrix mi-crostructure between Figs. l and 2 reflects the par- ticular orientation of low-index planes with respect to the surface of observation. Thermal etching contours of this type have been studied in detail by Hondros and Moore Both of the photomicrographs show that one or more dark spots are located approximately at the center of every protected area; where two spots are in close proximity, the protected areas have merged. The microstructures indicate that the anomalous resistance to thermal etching is related to the presence of these spots. Williams and Hayfield have shown that local regions of unusually high oxidation resistance can be caused by a surface monolayer of atoms with a work function higher than that of the base material. The result is an inhibition of the rate of electron removal from the base material and a decrease in the oxidation rate. The source of the protected layer may be either surface diffusion from contaminants on the specimen surface or pipe diffusion of solute atoms followed by migration across the surface. In the latter case the driving force is a difference in chemical potential resulting in a Gibbs adsorption phenomenon. In the present case, chemical polishing of the specimen surface precluded contaminants of a strictly surface nature. Consequently, diffusion of impurity atoms from within the lattice appears to be the most tenable explanation of the observed phenomena. The authors propose that the structures of Figs. 1 and 2 reflect the diffusion of impurity atoms along extended dislocations within the individual a phase grains prior to surface oxidation. The central spots within the protected regions are seen as sites of dislocation emergence which have become locally decorated with oxide in the manner discussed in Ref. 1. Williams and Hayfield observed protected regions adjacent to the grain boundaries of iron-contaminated copper which they attributed to the segregation of iron to the grain boundaries coupled with high dif-fusivity along the complex dislocation array at such boundaries. No evidence of such grain boundary protection was observed in the Cu-Si alloy; this

Jan 1, 1964

By J. H. Polhems, R. B. Brackin, D. B. Grove

P. L. Jones (Sink and Float Corp., New York)—The comparisons between galena and ferrosilicon medium should be applied only to the specific sink-float process used at Mascot since no evidence is presented that allows the comparison to be extended generally to galena medium as now used in other forms of sink-float. It is stated that flotation recovery of galena medium was tried but was unsuccessful and therefore the elaborate gravity system of medium recovery was applied. The expense of the gravity system at Mascot was one of the reasons for changing to ferrosilicon. However two important sink-float plants treating a combined total of over 13,000 tons of ore per day are using flotation to clean galena medium most successfully and are obtaining medium recoveries comparable with those reported in the paper for ferrosilicon. Slightly increased zinc recovery is claimed due to the change-over but it is to be noted that at the time of the change a decreased density differential was obtained in the separator. With galena a differential

Jan 1, 1952