Search Documents

In the Bowen Basin of central Queensland, coal production has gone from virtually nothing in 1961 to more than 24 million tons today4ut there's a cloud over this success.

Jan 1, 1977

By J. J. Bodmer

The substances or materials employed in this manufacture, are the same as those used in the preparation of mortar and concrete, viz., the different kinds of lime and sand. Instead of, or in conjunction with, sand there may be used calcined clay, blast-furnace slag, clinkers or ashes from furnaces, natural puzzolana, powdered chippings from stone quarries, etc. Of the different kinds of sand, pitsand—siliceous sand, as it commonly occurs mixed with gravel—and the sand found on the seashore, where the salt has been washed out by long exposure, whilst out of reach of the tide, may be used. The purer the above-named materials are from admixtures of clay, earth, or organic substances, the more complete will be their combination with the lime, the quicker will the manufactured brick or block set, and the more satisfactory will be the quality which it ultimately attains. For this reason, subdivided blast-furnace slag is preferable in most cases to sand, and the only sand which, in reference to setting capacity, is analogous to blast-furnace slag, is the volcanic sand occurring in different localities in North and South Wales, as an almost pure calcined silica. The lime used for the manufacture may be either slaked or unslaked. In the first case, (slaked), in order. to obtain satisfactory results, the lime must be strongly hydraulic. The use of unslaked lime, however, is by far preferable. A process for using fresh or unslaked lime has been patented in England by Major-General Scott. Lime thus prepared is called " selenitic lime," and consists of a mixture of fresh (unslaked) lime with sulphate of lime, or plaster of Paris. The graystone lime, for instance, found by the Medway, is mixed with from 5 to 7 per cent. of plaster, which has the effect of keeping the lime from slaking when water is added. This mixture also partakes of the nature of cement, and when used for mortar, or concrete, attains in a shorter time a greater degree of hardness than the same lime would ever have obtained after being slaked. Bodmer's process for the manufacture of artificial stone bricks consists chiefly in the use of automatic measuring, forwarding, and mixing apparatus, by means of which the materials are supplied and unite in a continuous stream, and are accurately measured. They

By August E. Vandale

Mining of the Freeport and Pittsburgh coal seams in the Pittsburgh vicinity dates back more than 100 years, and Consolidation Coal Co., or its predecessor, Pittsburgh Coal Co., has been actively mining in the area since 1900. Over the years, Consol has acquired good legal title to the coal lands purchased from individual farm owners, with broad mining rights, and in 98% or more of its title holdings, the company has a complete waiver of surface damage or the right to subside the surface land. (Titles in Pennsylvania can be in three forms: title in fee; title to the mineral; or mining rights permitting the removal and extraction of the mineral with or without waiver of surface damage.) In the early history of Consol, individual farms overlying the seams were purchased from land owners. Many of these titles severed the coal estate from the "in fee" title, and mining rights with waiver of surface damage were conveyed in the original severance deed. In this manner, Consol was able to put together its large mineable coal reserves. Consol has practiced "full recovery" mining as far as practical from its early years of hand loading to the recent era of mechanization.

Jan 9, 1967

By Louis Bender

AFTER investigating the work of coal-dust fired reverberatories of the Canadian Copper Co., at Copper Cliff, Ontario, the management of the Washoe Reduction Works decided to experiment with and ascertain the advantages of using coal dust as a fuel in their reverberatories. Consequently, during the month of June, 1914, reverberatory furnace No. 8 was changed in order to use powdered coal as a fuel. The results obtained by this method of firing are gratifying and show a decided saving in cost of smelting as compared to grate firing with lump coal. The furnace, as remodeled; is 124 ft. long by 21 ft. wide, and varies in height from 8 ft. 6 in. at the back end to 5 ft. 7 in. at the skimming end. The general construction of the furnace is similar to that of the other furnaces at this plant. There are no side doors to this furnace, as it was thought that with the present arrangement for feeding no "fettling" or "claying" would be required. The interior of the furnace can be inspected through the burner port holes, after shutting off the burners and giving a few seconds' time for the gases inside the furnace to clear away. The charging is done on either side of the furnace from longitudinal hoppers, extending a distance of 74 ft. from the back end of the furnace. Leading from the hoppers into the furnace are 6-in. pipes, spaced 194 in. apart, through which the charge is intermittently dropped. The charge is kept well above the slag line at all times; in this way the side walls are protected and no fettling is needed on this portion of the furnace. The remainder of the furnace requires fettling. After operating for three months, we found that the bricks were eaten into along each side wall from the skimming door back to the point where the charge had been dropped. The depth of this cutting away was 8 in. close to the front end and gradually tapered to zero at a distance of 50 ft., and was greatest on the side of the furnace having the larger flue connection. Hoppers will be put in for the entire length of furnace, from which fettling material will be dropped, to prevent this cutting.

Jan 1, 1915

By T. W. Watson, D. R. Flynn

,Measurements are reported for the thermal conductivity of four heat-resistant alloys which were measured at the National Bureau of Standards. Data are given for two samples of AISI Type 316 stainless steel covering a combined temperature range from -150° to + 800°C. The thermal conductivities of three samples of AISI Type 347 were measured over the temperature range from -150° to +150C. Thermal conductivity values are given for Carpenter 20 stainless steel from 100" to 800" C. Data are given for Inconel 702, in both the solution-annealed and the age-hardened condition, over the temperature range from -150" to +800C. SINCE 1958 the National Bureau of Standards, at the request of other government agencies or private laboratories, has carried out measurements of the thermal conductivity of a number of metals and alloys. This paper presents available thermal conductivity data obtained in this way on samples of four heat-resistant alloys. The data presented for Carpenter 20* stainless steel are, to the best of our knowledge, the only thermal conductivity values which have been reported for this alloy to date. Although thermal conductivity values for AISI stainless steels 316 and 347 have been reported by previous investigators, the present data are believed to be of particular interest because, for each alloy, the effect on thermal conductivity of small changes in chemical composition can be observed. The data on Inconel 702' are of interest, not only for

Jan 1, 1969

By D. C. Livingston

The Pilares de Nacozari mine is located ill Sonora, 75 miles south of Douglas, Ariz. The town of Douglas is on the International Boundary and is the place at which the ores from the Bisbee mines are smelted. The Moctezuma Copper Co. owns the mines at Nacozari, and the copper-concentrates shipped to the Copper Queen smelter, at Douglas, make a good smelting-mixture with the Bisbee ores. The Moctezuma Copper Co. and the Copper Queen smelter at Douglas, as well as the railroad from Douglas to Nacozari, are owned by the Phelps, Dodge & Co. The ore-deposit occurs in the form of a large ellipse with a major axis of approximately 2,000 ft. and a minor axis of about 600 ft., the major axis bearing about 9" W. of N. The

Jan 1, 1913

By Clyde E. Williams, JAMES L. GREGG

THIS review of the past year's progress in iron and steel metallurgy presents examples of only a few of the interesting or important accomplishments made in the United States. In the field of iron ore concentration increased attention was given to the study of the more difficultly separated wash ores and some progress was made in tabling. One difficulty with the table, in concentrating iron ore where the percentage of concentrate in the feed is large, has been the removal of fine silica from the thick layer .of concentrates in the cleaning zone. One company has -Made an important contribution toward the solution of this problem by an extension of the well-known plateau principle. By a special riffling of the plateau section of the table, the concentrates are crowded together. This action forces the fine silica to the top of the bed in the cleaning zone, whence the cross-flowing currents of water -can wash it into the middling product. Some work has been done on the application of froth flotation to the concentration of iron ores. Laboratory experiments were made at the Colorado School of Mines in which hematite was, successfully floated. Using oleic acid as a frothing and collecting agent and sodium carbonate as the conditioning agent, a high recovery of rich ,concentrate was obtained. A laboratory flotation unit is in use at Taconite, on the Mesabi range, and a commer-

Jan 1, 1932

By J. J. Bodmer

THE substances or materials employed in this manufacture, are the same as those used in the preparation of mortar and concrete, viz., the different kinds of lime and sand. Instead of, or in conjunction with, sand there may be used calcined clay, blast-furnace slag, clinkers or ashes from furnaces, natural puzzolana, powdered chippings from stone quarries, etc. Of the different kinds of sand, pit-sand-siliceous sand, as it commonly occurs mixed with gravel-and the sand found on the seashore, where the salt has been washed out by long exposure, whilst out of reach of the tide, may be used. The purer the above-named materials are from admixtures of clay, earth, or organic substances, the more complete will be their combination with the lime, the quicker will the manufactured brick or block set, and the more satisfactory will be the quality which it ultimately attains. For this reason, subdivided blast-furnace slag is preferable in most cases to sand, and the only sand which, in reference to setting capacity, is analogous to blast-furnace slag, is the volcanic sand occurring in different localities in North and South Wales, as an almost pure calcined silica. The lime used for the manufacture may be either slaked or unslaked. In the first case, (slaked), in order to obtain satisfactory results, the lime must be strongly hydraulic. The use of unslaked lime, however, is by far preferable. A process for using fresh or unslaked lime has been patented in England by Major-General Scott. Lime thus prepared is called " selenitic lime," and consists of a mixture of fresh (un¬slaked) lime with sulphate of lime, or plaster of Paris. The gray-stone lime, for instance, found by the Medway, is mixed with from 5 to 7 per cent. of plaster, which has the effect of keeping the lime from slaking when water is added. This mixture also partakes of the nature of cement, and when used for mortar, or concrete, attains in a shorter time a greater degree of hardness than the same lime would ever have obtained after being slaked. Bodmer's process for the manufacture of artificial stone bricks consists chiefly in the use of automatic measuring, forwarding, and mixing apparatus, by means of which the materials are supplied and unite in a continuous stream, and are accurately measured. They

Jan 1, 1874

By I. I. Gardescu

Rumania produced during 1936 some 62,500,000 bbl. of oil. Of this production, 99 per cent comes from an area running east and west along the southern foothills of the Carpathian Mountains just north of Bucharest. This almost rectangular area measures 20 by 40 miles and is located in the districts of Dambovita and Prahova between the cities of Targovigte to the west and Mizil to the east. The remainder of the production is about evenly divided between the oil fields north and east of Mizil in the Buzh district and those to the north on the eastern flanks of the Carpathian Mountains in the district of Baciiu. The Transylvanian Basin to the north and west of the Carpathian Mountains has produced to date only dry gas from its numerous salt domes. Bucsani Field The Bucgani oil field produced 15,600,000 bbl., or 25 per cent of the total production of Rumania in 1936. Bucgani is a deep-seated salt dome 7 miles south of the old Moreni oil field. A slight surface doming, not dissimilar to the topography observed on some of the oil fields of the Californian basin, called attention to the area. It is the southernmost oil field and, together with the deep-seated and prolific Boldesti field, points to the great oil possibilities of the deep-seated domes along the northern edge of the Rumanian plains south of the Carpathian foothills. The Government is the principal owner of the oil and gas subsurface rights in the areas south of the foothills. The acquisition of leases by the operating oil companies may be made either by application for an exploration permit, the company being assigned part of the acreage in case of successful wildcatting, or, if the area has already been declared as proven territory, through competitive bidding. A block of 164 acres was auctioned recently for $200,000, or $1200 per acre. The largest producer in the Bucgani oil field is the Steaua Romana, which produced 39.5 per cent of the total for the field. The Steaua Romana is a post-war company and 50 per cent of its shares are owned by the British Steaua and the Steaua Franpaise and the other 50 per cent by a group of Rumanian banks and by the Government. The Colombia,

Jan 1, 1937

By R. S. Shoemaker, F. W. McQuiston

CAMPBELL RED LAKE MINES Balmertown, Ontario 1974 Operating Data MINE LOCATION: Balmertown, in Red Lake mining area of Ontario TYPE OF MINE: Underground mine developed by vertical shaft to 4300 feet. Mining active above 3000 ft depth. ORE DESCRIPTION: Gold and minor silver.. Sulfur content about 1.3%. Ar senopyrite , pyrite, pyrrhotite, and stibnite. CAPACITY IN TONS124 HRS: 825 ASSAY: 0.66 oz Au per ton heads MILL PROCESS: Amalgamation, flotation, roasting of concentrate and separate treatment of calcines and flotation tails by cyanide. PLANT BUILDING: Mine mill and service facilities all housed in insulated and heated buildings POWER: Total consumption, mine and mill - 100 Kwh/T WASTE DISPOSAL: Impoundment of tailings. Arsenic to sealed underground storage EMPLOYEES: Total of 300 men on payroll. Housing in Balmertown and nearby communities.

Jan 1, 1975

Discussion of the paper of F. C. NEWTON, presented at the New York meeting, Feb-ruary, 1915, and printed in Bulletin No. 9S, February, 1915, pp. 473 to 477. H. 0. HOFMAN, Boston, Mass.-The results of these large-scale experiments, which were carried on at Perth Amboy, show that there are many differences between theoretical conceptions and their applications to work on a large scale. The author has given reasons why the results of bringing a desilverizing kettle to the high melting point of the zinc-silver alloy, Zn3Ag2, melting at 665° C., are not satisfactory. In all probability the alloy is dissolved in the lead; it may also be decomposed by the lead; the practical result is that this high temperature does not work. It remains now for the laboratory man to carry on systematic experiments

Jan 5, 1915

By AIME AIME

BERYLLIUM is one of the most interesting of the minor metals and distinctly a modern development, for until the last two decades it had practically no commercial importance whatever. Then it was discovered that when small quantities of it were alloyed with copper, a copper alloy of unusual and valuable qualities resulted. This is by far its major use-in the manufacture of strong, heat-treated copper-base alloys in which the beryllium content varies from about 0.3 to 2.5 per cent. Its second most important use, though much smaller, is in the form of oxide or other nonmetallic products in the fluorescent lamp, X-ray, cathode ray, and television industries. Certain beryllium salts have the quality, in common with several other materials, of transforming short-wave radiation and cathode rays to visible radiation. Such materials are commonly known as phosphors, and the beryllium salts are the most important phosphors now in use. The third largest use for beryllium is for ceramics, including refractories. Beryllium is also used in small quantities in the form of the metal itself.

Jan 1, 1943

By L. Massé, Th. Koulomzine

NOTE ON HAALCK'S FORMULA QUANTITATIVE interpretation of magnetic anomalies is admittedly a difficult process. Few authors have attempted a general approach to this problem. A [ ] number of publications can be found widely scattered through scientific periodicals, which present particular solutions obtained by the introduction of simplifying assumptions, such as the reduction to an equivalent magnet or pole, or the hypothesis of a very thin vein. The practical applications of these solutions are necessarily very restricted though they have given satisfactory results in isolated cases. Probably the most widely known equation of this type was given by Haalck.l His classic work contains curves calculated for typical conditions, and has now become a standard reference. However, a close scrutiny of Haalck's derivation reveals that, aside from the hypothesis of a thin vein, it rests on the

Jan 1, 1947

By R. Floyd Farris

Al thorough knowledge of the behavior of cement slurries under elevated temperatures and pressures is necessary in order to solve properly the many problems presented in deep-well cementing operations. In the earlier days of the petroleum industry the depths of wells were shallow as compared to those of today, and the subsurface temperatures and pressures were not of sufficient magnitude to affect seriously the problem of proper control of cement-slurry properties. Today, however, the search for new reserves has extended drilling to such depths that bottom-hole temperatures of more than 200°F. and bottom-hole pressures of 3000 to 5000 lb. are not uncommon. Moreover, there is every indication that within the next few years wells will be drilled to even greater depths and bottom-hole temperatures and pressures will be correspondingly higher than those with which we are concerned today. It has been realized for some time that the behavior of cement slurries at high temperatures and pressures might be very different from that at atmospheric tempera-ture-pressure conditions, but while the temperature effects have been investigated with a reasonable degree of thoroughness, the pressure effects have received little public attention. While the trend toward deeper drilling may make changes in cementing technique and the choice of cements imperative, it was the purpose of this investigation to consider factors having a bearing on the latter, only secondary consideration being ,given, for the present, to details of tech-nique and equipment for oil-field use. More specfically, the purpose of this work was to consider the effect of temperature and pressure upon the behavior of cement slurries. Although it has long been recognized that cements thicken and set rapidly with increasing temperatures, practical methods for the quantitative determination of these effects are comparatively recent developments. In 1935 Silcox and Rule1 presented such a method, describing apparatus designed to measure the consistency-time relationship of cement slurries at relatively high temperatures. The practical importance of this apparatus in furnishing useful data for the evaluation of cement slurries for cementing operations has been emphasized in various technical publications by such writers as E. L. Davis,~ I. F. Bing-ham,3 and J. E. Weiler.4 A paper describing the numerous tests now used to evaluate cements for oil wells was presented in 1939 by W. W. Robinson.= Robinson describes the Consistometer and the Thickening-Time Tester, showing similarity of data from the two devices, and points out that the purpose of each apparatus is to determine the allowable time that a cement may be pumped at a given temperature. At the present time, however, it is believed that results from the Thickening-Time Tester and the Consistometer have not given a

Jan 1, 1941

By R. Floyd Farris

Al thorough knowledge of the behavior of cement slurries under elevated temperatures and pressures is necessary in order to solve properly the many problems presented in deep-well cementing operations. In the earlier days of the petroleum industry the depths of wells were shallow as compared to those of today, and the subsurface temperatures and pressures were not of sufficient magnitude to affect seriously the problem of proper control of cement-slurry properties. Today, however, the search for new reserves has extended drilling to such depths that bottom-hole temperatures of more than 200°F. and bottom-hole pressures of 3000 to 5000 lb. are not uncommon. Moreover, there is every indication that within the next few years wells will be drilled to even greater depths and bottom-hole temperatures and pressures will be correspondingly higher than those with which we are concerned today. It has been realized for some time that the behavior of cement slurries at high temperatures and pressures might be very different from that at atmospheric tempera-ture-pressure conditions, but while the temperature effects have been investigated with a reasonable degree of thoroughness, the pressure effects have received little public attention. While the trend toward deeper drilling may make changes in cementing technique and the choice of cements imperative, it was the purpose of this investigation to consider factors having a bearing on the latter, only secondary consideration being ,given, for the present, to details of tech-nique and equipment for oil-field use. More specfically, the purpose of this work was to consider the effect of temperature and pressure upon the behavior of cement slurries. Although it has long been recognized that cements thicken and set rapidly with increasing temperatures, practical methods for the quantitative determination of these effects are comparatively recent developments. In 1935 Silcox and Rule1 presented such a method, describing apparatus designed to measure the consistency-time relationship of cement slurries at relatively high temperatures. The practical importance of this apparatus in furnishing useful data for the evaluation of cement slurries for cementing operations has been emphasized in various technical publications by such writers as E. L. Davis,~ I. F. Bing-ham,3 and J. E. Weiler.4 A paper describing the numerous tests now used to evaluate cements for oil wells was presented in 1939 by W. W. Robinson.= Robinson describes the Consistometer and the Thickening-Time Tester, showing similarity of data from the two devices, and points out that the purpose of each apparatus is to determine the allowable time that a cement may be pumped at a given temperature. At the present time, however, it is believed that results from the Thickening-Time Tester and the Consistometer have not given a

Jan 1, 1941

By Robert S. Nichols

Fording Coal Limited's mine in the Rocky Mountains near Elkford, B.C. has produced 21.8 million clean tonnes of metallurgical coal from 1971 to 1980, inclusive. This production has come from several pit areas and required the removal of 149.1 million bank cubic meters of waste rock and overburden by truck-shovel and dragline operations. Waste dumps from 30m to 200m in height have been successfully constructed on natural slopes, generally between 10° and 26°. Design considerations for the dumps include foundation and soil conditions, natural slope angles and containment of weak overburden or rehandle materials. Dump control is maintained by monitoring the crest and the face of an active dump area. Crest movement is measured by extensometers locally termed "Spoil Monitors". When crest movement rates progressively increase above normal, dumping operations are temporarily relocated. Some unstable conditions and mass failures have occurred as the result of natural foundation slopes being in excess of 26°, failure of weak water saturated foundation soils or weak material being placed on the dump.

Jan 1, 1983

By Benjamin Lustman, Robert F. Mehl

THE study of the high-temperature oxidation of pure metals, intensively pursued experimentally since the pioneer work of Pilling and Bedworth1 and supplemented by the recent theoretical work of Wagner2 is now well advanced. The important field of low-temperature oxidation-i.e., oxidation extending only through the temper color range of thicknesses with the formation of thin oxide layers in the range from o to 1000-2000 Angstroms-has not, however, reached so satisfactory a state, owing largely to the experimental difficulties that attend the formation and study of thin films; most of the work has been performed on abraded specimens whose surface irregularities approximated the thickness of the films formed. It has been pointed out that the rates of oxidation of different crystal faces are different and that the difference may be related to the orientation relationships that obtain between the metal crystal and the superimposed oxide crystal; it has also been suggested that this orientation dependence should manifest itself in rates of oxidation and perhaps also of corrosion in aggregates bearing preferred orientations. 3,4 An attempt to measure the rates of oxidation of different crystal faces of alpha iron demonstrated this difference in rate,4 but the dependence of rate on orientation was not simple; the method of measuring thickness, consisting of a color comparison with barium stearate multi-films of known thickness, was not wholly satisfactory. For these reasons it was felt that a study of the rate of oxidation of single crystals prepared with surfaces as smooth as possible, using a sensitive method giving true film thickness, should be profitable. Copper was chosen because of the ease of reduction of the primary oxide film and because the orientation relationships between metal and oxide and the composition of the oxide films formed at low temperatures are known; for thin films formed at low temperatures, Cu2O alone occurs.22-24 EXPERIMENTAL PROCEDURE Various methods of surface preparation were attempted in order to obtain a surface that would oxidize uniformly and reproducibly. Electrolytic polishing by the method of Jacquet5 and electrolytic and mechanical polishing followed by annealing in vacuum and in purified hydrogen at various temperatures were tested. The procedure finally adopted consisted in a fine metallographic polish followed by an anneal in purified hydrogen at temperatures of 900º to 1000°C. for 12 hr. or more. The surface so produced was very bright and smooth, with no trace of specular etching (though some grain-boundary etching was observed); indeed, fine scratches produced by the final polish were entirely removed by the high-temperature anneal.

Jan 1, 1941

By Oscar A. Glaeser

THE mine and plant of the United Verde Copper Co., located in Yav-api County, at Jerome, Arizona, have been described in various technical publications and, therefore, a brief outline of its essential features will suffice. The orebodies are of the schist replacement type, the main sulfide mass being a large lens-shaped body approximately 7 acres in cross-sectional area. In general, the mineralization is found along the iron-schist contact, with the orebodies extending about 1000 ft. along this contact and varying from a few feet to 250 ft. in width. The mine is located on a mountain slope and has openings into it on three horizons, as follows: 1. Raises and ore passes open vertically into the shovel pit. These extend down to the 1000-ft. level, where they terminate as loading bins in the Hopewell adit. The main fan intake air shaft, which also extends vertically down to the 1000-ft. level, has its surface opening on the hillside at the extreme north end of the shovel pit, and the main mine air return exhausts through a raise at the extreme south end of the shovel pit. 2. The 500-ft. level adit. 3. The Hopewell adit on the 1000-ft. level. The mine has a vertical downward extent of 2000 ft. below the 1000-ft. level. Underground operations are carried on through two main shafts, both of which are wholly underground. Shaft 5 is the ore-hoisting shaft. It has three compartments and extends from the 800 to the 3150-ft. level. Shaft 6 is the service shaft, and is used for lowering and hoisting men and material. It has a large cage compartment and three smaller compartments for counterweights, ladderway, and pipe and power lines. This shaft extends from the 500 to the 2550-ft. level, and is now being extended to the 3000-ft. level. An air shaft for the downward movement of fresh air from the fan has been provided, and extends to the 2550-ft. level at this time. Work has been started to extend this air shaft to the 3000-ft. level. A return airway for vitiated mine air, in the form of raises and short connecting drifts, extends downward to the 2100-ft. level. The underground mining operations extend from the 300 to the 3000-ft. level. There are about 45 stopes in active operation on the 17 levels

Jan 1, 1929

By John H. Walthall, Raymond L. Copson, Travis P. Hignett

In October 1942, the War Production Board requested the Tennessee Valley Authority to undertake investigations to determine the feasibility of producing alumina suitable for reduction in aluminum cells, from clays and other domestic materials, by a lime-sintering, soda-ash leaching process. The work was undertaken by the chemical engineering staff of the Authority under the general direction of the War Metallurgy Committee of the National Academy of Sciences. The investigation included small-scale tests to determine the most suitable conditions for the process, and construction and operation of a pilot plant to obtain data for evaluation of the process and for design of a plant. The results of this investigation are described in the present paper. Sources of Alumina Alumina for the commercial production of aluminum is obtained from bauxite by the Bayer process. The tremendous demand for aluminum for wartime uses is causing rapid exhaustion of the high-grade bauxite deposits in the United States. On the other hand, there is an abundance of aluminous materials such as clay and lower grades of bauxite, which are not suitable for treatment by the Bayer process because of their high silica content. The Tennessee Valley Authority has conducted research and pilot-plant work for more than 5 years on methods for the production of alumina from clay and low-grade bauxite. Particular attention has been given to the high-grade white kaolin found in Carroll County, Tennessee. Exploratory drilling has demonstrated that at least 4 1/2 million tons of kaolin containing in excess of 34 per cent AlzOI is available in this area by strip-mining methods. It has been estimated that hundreds of millions of tons of clay of similar quality occur in the Tennessee Valley region. The Process The process is illustrated in the flowsheet (Fig. I), and consists essentially of the following steps: I. Heating a mixture of clay and limestone to form a sinter containing calcium aluminate and dicalcium silicate. z. Leaching this sinter with a dilute sodium carbonate solution, to form a sodium aluminate solution and a calcium carbonate, calcium silicate residue, which is discarded. 3. Treating the sodium aluminate solution with carbon dioxide to precipitate aluminum trihydrate and regenerate the sodium carbonate solution, which is recycled. 4. Heating the aluminum trihydrate to produce alumina. The process was considered promising because of the abundance and cheapness of the two raw materials, clay and limestone; and because, as compared with an acid process, smaller amounts of critical

Jan 1, 1944

By Charles T. Holland, David A. Olsen

Considerable work has resulted in the development of a formula by which the strength of coal pillars for an L to T ratio of up to 12 may be estimated. One of the factors involved in this formula is the coefficient of friction between the coal pillar and the adjacent rock with which it is in contact. This paper presents the results of studies on sandstone, limestone, shale and coal and the coefficient of friction between coal and the other three under wet and dry conditions. With the coefficients of friction thus determined and the use of results obtained earlier by Meikle and Holland, it seems probable that coal pillar strength may be more closely estimated. Several investigators1-3 have found that the com-pressive strength of cubical coal specimens can be correlated by an equation such as

Jan 1, 1969