Search Documents

By C. W. Mueller, P. H. Robinson

A technique was developed for depositing single -crystal films of silicon on single-crystal sapphire substrates via the pyrolytic decomposition of SiH4/H2 mixtures. Electron diffraction and X-ray Laue reflection examinations of these films revealed single-crystal patterns. These films were characterized by measuring conductivity type, thickness, resistivity, and Hall mobility. Chemical etching, dislocation staining, and electron-microscopy examination have indicated the presence of low-angle grain boundaries and microtwinning in the silicon films. The role of the sapphire substrate with respect to its quality, orientation, surface finish, and thermal and chemical treatment was investigated. Hall mobility as a function of sapphire orientation was measured. A mobility equal to 88 pct of bulk silicon mobility was attained. Insulated-gate field-effect transistors which have a transconductance of 4000 pmho at 6 ma were fabricated using these films. THE technology of the fabrication of microelectronic circuits with active and passive components directly on a single wafer of semiconductor material has attained a high degree of perfection during the last few years. One inherent difficulty with the single-wafer approach has been undesirable coupling between components arising from the common base material. Several techniques have been developed for minimizing this coupling and obtaining good electrical isolation between components; however, these result in extra capacitance being added to the circuit. The extraneous capacitance of the connecting leads, resistors, and capacitors degrade circuit performance and limit the high-frequency operation of these circuits. Recently there has been considerable interestl-3 in the deposition of silicon films upon insulating substrates. The use of silicon as the semiconductor allows the subsequent utilization of the large amount of technology which has been developed for silicon for the fabrication of good active components. A sapphire substrate supplies an excellent insulating material which at the same time gives a thermal-conductivity improvement of an order of magnitude over glass-type substrates. This paper will describe the results obtained for the deposition of single-crystal silicon layers upon single-crystal sapphire substrates as well as the characterization of these films. I) APPARATUS The 'system used for the growth of silicon films on sapphire substrates by means of the pyrolysis of SiH4/H2 mixtures is shown in Fig. 1. The all-quartz reaction chamber is water-cooled and includes a quartz optical-flat window for use in conjunction with a 5 kw, 2.5 Mc per sec constant-temperature controlled rf generator. The temperature sensor for the rf generator is a thermopile which is focused through the quartz optical flat onto the susceptor surface. With this system the rf generator will hold the temperature of the susceptor to about +0.3°C at 1200°C. The susceptor is supported on a quartz sled inclined to the gas flow to increase the uniformity of the deposition. The water jacket surrounding the reaction chamber is used to keep the quartz wall temperature low enough to limit the decomposition of the silane to the rf-heated susceptor which contains the sapphire substrates. This eliminates the reaction of silicon with the hot quartz to form SiO which deposits out on the apparatus walls, thus obscuring vision, and interferes with the optical measurements of the temperature as well as with the growth process itself. Provision is also made for "n"- and 'p"-type doping by using mixtures of either phosphine or diborane in hydrogen which are added to the silane during the growth process. The hydrogen used is the purest commercially available tank hydrogen further purified by use of a palladium diffuser. The susceptors which were used include 1) spectro-scopically pure graphite, 2) high-purity molybdenum, 3) high-resistivity silicon using a low-resistivity insert to facilitate coupling to the rf generator, 4) silicon carbide-coated graphite. The latter two susceptor materials produced silicon films on sapphire substrates with more reproducible resistivities. Prior to silicon deposition all connecting lines as well as the reaction chamber are thoroughly flushed with argon and then hydrogen. After the hydrogen flow is set, the growth temperature is adjusted to 11009 to 1150°C, and when thermal equilibrium is reached the silane flow is started. The flow rate of the hydrogen must be fast enough so that turbulent flow occurs in the size of reaction tube used, otherwise a streaked nonuniform silicon deposit occurs. After the deposition

Jan 1, 1967

By P. H. Brace, N. A. Ziegler

The study of the relations between gases and metals is one of pcren-nial interest to all who are connected with the production of high-grade metallurgical products. The data reported here are the outcome of work of which the object is to determine the effects of dissolved gases upon the properties of metals and to gain a more detailed knowledge of the reactions between gases and molten metals, particularly iron, under definitely controlled conditions. We have attempted to reduce our margin of error by dealing with relatively large quantities of metal, from 4 to 13 Ih. (2 to 6 kg.), and keeping the ratio of refractories to metal as small as practicable. The ingots produced are large enough to provide adequate material for making determinations of magnetic and other physical properties. In choosing the bell-jar type of furnace we were influenced by the results of considerable experimentation along the same general line which indicated that, for the scale on which we were to work, it was important to have the furnace structure independent of the vacuum enclosure. The use of a bell-jar surrounding the entire furnace accomplishes this and also gives great freedom of observation during operation and ready accessibility for the replacements which are necessary after each run. Our choice of analytical method was made in the light of the results secured by H. M. Ryder, who used a method similar in principle for the analysis of very small quantities of gas extracted from strips of metal heated electrically in high vacuum. We have presented some selected preliminary experirnental data as being illustrative of the quantity and nature of the gases which occur in iron of different origins, but do not urgc any hypothesis at this time. The Furnace Our furnace may be described as "a high-frequency induction furnacc of the bell-jar type." It is similar in a general way to that described by Cain and Peterson1 though we have introduced certain refinements of

By J. L. Brimhall, R. A. Huggins

The structure of deformed internally oxidized alloys of siluer- cotztcrining magnesium and copper-containing aluminum in was studied by thin-film transrrzissiotz electron microscopy. With low to moderate amounts of stvain, the deformation structure in t11e dispersion-hardened alloys was found to consist of a high density of dislocations arranged it a random distribution or in a very fine, but poorly defined, cell stucture, depending on the fitness of the dbsbersion and amount of deformation. 112 contrarst, both pure copper and silver show relative1y Large, distinct cell structures. The particular structures in the alloys are believed to result from particles acting as both dislocaliot~ sources and deflector-s. The Inck of a pvorzolrr~ced deformation texture tr~ regiotzs qf' seoere loctll plastic curvature after heavy deformation can also be traced to the formation of clislocntions on many slip systemes and a lack 01 local concentrations of dislocations of predominantly one sign. THE presence of fine dispersions of a second phase has long been known to have a strong influence upon the mechanical properties of solids. Until recently, the influence of particles on the deformation mechanisms has been assumed to be solely that of barriers to dislocations. This is seen in the classic models of edge dislocations being restrained by the particles.1 4 There is, however, considerable evidence that this is not their primary effect, and that the particles can have a large influence on the defect structure generated by plastic deformation. The presence of particles causes changes in the surface topography observed after deformation. In overaged precipitation-hardened materials containing hard, noncoherent precipitates, fine intersecting slip lines are found after deformation of single crystals. indicating the activation of many slip systems. This has been extensively observed in the A1-Cu systen;, both by optical microscopy and replica electron microscopy.'"13 In some of the observations. the slip lines were seen to extend between the particles. Similar observations of extremely fine slip lines or the apparent absence of normal slip lines have also been found in A~-M~."

Jan 1, 1965

By A. Kenneth Schellinger

THE terms surface tension .and surface energy are well known when applied to liquids and are generally described by referring to the excess energy of the air: liquid interface as a result of unsaturated molecular forces surrounding the surface molecules of the liquid due to the presence of the air phase on one side. Such unbalanced forces produce the familiar water droplet of spherical form and are generally summed up as a surface tension measured in dynes per centimeter which can be shown mathematically to be equal numerically to a corresponding surface energy expressed in ergs per square centimeter. A specific surface energy, however, is best thought of as the energy necessary to produce one unit of new surface on a substance. Hence, in producing a bubble in a flotation cell the impeller must supply surface energy corresponding to the air: liquid interfacial area on the interior of the bubble. Inasmuch as it is relatively easy to extend or contract the surface of a liquid, there are a number of successful methods for liquid surface tension, or energy, measurement based upon surface deformation. This happy state of affairs does not, however, extend to solids, which are considered to possess surface energies for the same reasons as do liquids, i.e. because of unsaturated ionic bonds at the solid gas interface. As in the case of the flotation cell producing surface on liquids as new bubbles, it takes energy to produce new surface on solids as new particles. As every mill man knows, this surface is produced on mineral solids in a grinding mill by the action of a tumbling mass of iron balls. But here so much energy usually is wasted by the inefficient action of these balls that a large amount of heat is generated, and the surface energy production may be easily confused with the energy necessary to produce this ineffective heat. The tumbling balls and fracturing minerals ultimately take their energy from a rather large electric motor. It has been variously estimated that from 10 to 20 pct" only of this energy from the motor does not appear as heat and may be presumed to appear as surface energy on the minerals present.. Such a production of new surface on the mineral phases is accompanied, of course, by a size reduction that is inevitable as more and more mineral interior molecules become surface molecules by the fracture exposure. This size reduction of mineral particles, although the most obvious feature and perhaps the sole object of the milling operation, is from this energy viewpoint the outward manifestation of the production of surface energy only. Measurement of the characteristic surface energies of pure minerals and their various mixtures in ores would be a step towards understanding of the energetics of the commercial grinding operation. In addition, the characteristic surface energy of a mineral is probably a physical property specific for that mineral, and therefore, from a scientific standpoint, should be measured. It is interesting to note that, in contrast to the large body of work on the surface tensions of liquid systems and biological systems, the field of solid surface energies has been neglected. Prior to. 1920 it is difficult to find more than one or two references to work on solid surface energies in Chemical Abstracts. Since 1920 such references number somewhat less than 100, while those on liquid systems are numbered in the thousands. Much of this apparent neglect of the field of solid surface energies (the term is intended to be somewhat inclusive at this point and refers both to the solid: gas, and the solid: liquid interface) is because of the lack of a reliable method of measurement rather than any lack of scientific curiosity. It was, and still is, difficult to produce new surface on a solid without the simultaneous production of interior changes in the same solid which may consume part of the energy used. The extension in the surface area can be measured, but the interior crystal-

Jan 1, 1952

By P. H. Royster, T. L. Joseph

In a study of the blast-furnace process, the Bureau of Mines has made many experiments for the purpose of determining the exact nature of the combustion of coke in the neighborhood of the tuyeres. Two papers1 presented at a meeting of this Institute discussed somewhat the practical aspects of coke combustibility in its relation to the operation of the blast furnace. In a later paper,2 Sherman and Kinney discussed the possible effect of variations in the combustibility of cokes on the furnace operation, and find that the "reoxidation theory" of Koppers and the "heat concentration theory" of Brassert³ are insuffcient to explain the variation in the conduct of different cokes that has been observed by furnace operators. In their report to the D-5 Committee of the American Society for Testing Materials, with which the Bureau of Mines has been cooperating, Perrott and Fieldner4 seem to agree with Sherman and Kinney that, for practical purposes, the nature of the combustion of coke at the tuyeres of any furnace is constant and is affected neither by the physical properties of the coke nor by the nature of the furnace operation. They omit as unimportant any tests on the combustibility of coke from their proposed methods for standard tests on coke. In the last two papers, it is pointed out that performance tests, in which all other factors except coke quality are kept constant, are to be desired and

Jan 1, 1924

By T. G. Digges, M. R. Achter

ALTHOUGH zone melting has found favor in recent years because of its convenience and its faster rate of production of single crystals, the older technique of strain annealing still has a number of advantages. It has been reported1 that the lattice of a crystal prepared in this manner has fewer defects than one grown from the melt and, of course, the control of the external geometry is easier. Also, the diameter of the crystal which can be grown by zone melting has a theoretical limit determined by the surface tension, thermal conductivity, and specific gravity of the material, while the size of that which can be grown in the solid state is limited only by practical considerations. In a program for the study of the structure-sensitive properties of niobium and its alloys it was desirable, for ease of handling, to have available single crystals of large diameter. This requirement dictated the choice of the strain-anneal technique. Induction heating was chosen in the present work in preference to other methods because of its deep penetration of large-diameter sections. A five-turn coil, powered by a motor generator operating at 10,000 cps, is contained in a vacuum chamber. The work is lowered through the coil for both the recrystallization and the crystal-growth steps. Starting with electron-beam melted material, the bars are cold-swaged, recrystallized, strained in a tensile machine, and then subjected to the growth step. Single crystals have been grown under the following conditions: Reduction in area during swaging— 79 to 99 pct, recrystallization temperature—1500o to 1667°C at the rate of 1.25 in. per hr, strain—1.0 to 2.5 pct, growth temperature—1600o to 2400°C at rates from 0.15 to 1.25 in. per hr. Starting grain sizes achieved after the recrystallization step varied from 0.6 to 1.55 mm. The starting grain size was found to be critical; if it is too fine and has any residual cold work, as shown by the presence of a fiberlike texture, a single crystal cannot be grown. Using this technique niobium single crystals have been grown from 0.250 in. diameter and 12 in. long to 1.00 in. diameter and 5 in. long as shown in Fig. 1. The 1-in. crystal is the largest to be reported for a refractory metal as compared to 0.500 in. for molybdenum grown by zone melting.2 As with zone melting, control of orientation is possible by the use of special procedures. Other investigators, see for example Williamson and Smallman,3 have reported that orientation control may be achieved by a bending technique. In the present work the strained rod is partially lowered through the coil to start the growth of the crystal. Then it is removed and bent at a point ahead of the interface between the single and polycrystalline portions. Finally, it is returned to the chamber and growth is continued "around the corner". The amount of bending which can be imparted to the rod is limited by coil geometry which up to now has been 10 deg. However, by repeating the bending and growing operations it should be possible to attain any desired orientation. The perfection of these single-crystal specimens as a function of process variables is being measured by X-ray and metallographic techniques and the results will be reported in a forthcoming paper. This work was partially supported by the Advanced Research Projects Agency.

Jan 1, 1964

By H. Ries, R. E. Somers

Bodies of pyritic ore in schistose rocks have long been known in different parts of the world. The several occurrences resemble each other in being usually of more or less lenticular shape, inclosed in walls of schist or gneiss, and carrying pyrite, chalcopyrite, and pyrrhotite in varying proportions, as the chief ore minerals. The deposits differ, however, in that sometimes one, sometimes another, of the three sulphides mentioned may predominate. The orebodies in general are more or less closely conformable with the schistosity of the wall rocks, although in cases this may not hold true. The boundaries may or may not be sharp, but in general are fairly distinct. The lenses vary in size, may occur singly, or in groups; in the latter case they may be in line, overlapping, or occasionally parallel. Pinching and swelling of individual lenses is not uncommon. The genesis of these pyritic bodies has provoked much discussion, and they have been variously classed as sedimentary, igneous intrusions, hydrothermal replacements or impregnations, etc. Indeed, in some cases different geologists have most positively assigned widely diverse origins to the same deposit, as in the case of Rio Tintol and Rammels-berg.2 It is true that in the light of modern criteria, we have been able in a few cases to decipher clearly the process of origin and so there seems no. doubt now regarding the genesis of the deposits at Rio Tinto, Spain;3 Rammelsberg, Germany;4 Ducktown, Tenn.;5 southwestern Virginia;=

Jan 1, 1918

By A. A. Dor

Out of nine new major iron ore concentrators put in operation during the last three years, or expected to be commissioned in 1968, seven incorporate primary grinding mills and have a total design capacity of 13,150,000 ltpy of pellets, while only two include conventional rod and ball mill grinding circuits for a total design capacity of about 6,100,000 ltpy (Table I). This evolution in the application of primary grinding to hard, fine grained magnetite ores represents an important development in the technology of mineral processing. It has been the outcome of comprehensive testwork in the laboratory and in pilot plants.

Jan 11, 1968

By P. Payson

INTERGRANULAR corrosion in corrosion-resistant chromium-nickel steels has been widely discussed in the last few years. So far as the author knows, nothing has been published which definitely shows that this tendency can be eliminated, although suggestions have been made that a remedy is possible if certain specifications are satisfied. Strauss, Schottky and Hinueber1 suggested an increase in chromium content to an extent that would prevent the impoverishment of chromium on carbide precipitation sufficient to cause impaired corrosion resistance in the matrix. Pilling2 suggested an increase in nickel, so that the stability of the austenite matrix would be increased. Aborn and Bain,3 say that "intergranular attack-may be eliminated by preventing carbide precipitation (e. g., by lowering the carbon content or somehow raising its solubility) or by precipitating it permanently under conditions which will not remove chromium from solid solution so drastically at any points." In a later paper Aborn and Bain4 state that many different metallic elements, tungsten, vanadium, copper, aluminum, molybdenum, titanium and zirconium, have been added in small per-centages to increase the stability of these alloys, but that it has been reported that according to the copper sulfate test these added elements act only to retard the intergranular corrosion, and that increased nickel and chromium contents have similar effects. Newell5 showed that the lower the quenching temperature before reheating, the less severe was the intergranular attack.

Jan 1, 1932

By H. J. Tschirner, L. P. Davidson, R. K. Carpenter

HE electrolytic zinc plant of the American Zinc Co. of Illinois, at Monsanto, was expanded in 1943 to a capacity of 100 tons of slab zinc daily. This capacity was not attained because of inability of the leaching plant to deliver an adequate amount of solution for electrolysis. Changing the leaching method so that the acid was added to the roasted zinc material reversed the usual procedure and made it possible to attain the desired capacity. The conditions which prevented satisfactory work before this change and the difficulties which arose in reversing the usual leaching procedure are described. The "reverse" leach operation as now practiced is carried out as follows: All the calcine to be leached is fed continuously to a slurry mixing tank. About one third of the acid to be used is fed to the tank with the calcine. The slurry is discharged continuously to a Dorr duplex classifier in closed circuit with a Hardinge mill. The classifier overflow is pumped to any of six leaching tanks where the leach is completed. A finished leach is discharged through Allen-Sherman-Hoff pumps to Dorr thickeners, from which the overflow goes to the zinc dust purification and the underflow to vacuum filters. This change in leaching procedure from the usual one of adding calcine to a large amount of acid made it possible to provide an adequate amount of purified solution to the electrolyzing division and at the same time filter and dry all the residue produced. Operating savings in reagents and better metallurgical recoveries were also important benefits. The original flowsheet of the leaching plant provided leaching, sedimentation of the insoluble residue, and purification of the neutral zinc sulphate solution with zinc dust. The thickened residue was filtered and washed. The purification cake of excess zinc dust, precipitated copper and cadmium, and any insoluble residue was filtered off on plate-and-frame duplex classifier. Settlement in the thickeners was inadequate and the suspended solids in the thickener overflow gave rise to filtration difficulties after the zinc dust purification. Further, the filtration and washing of the leach residue was poor, and it became necessary to pump a large amount of unwashed or poorly washed residue to storage ponds outside the plant building. Two causes of the poor settling and filtration were determined: Soluble silica and ferrous iron in the calcine treated. The latter was a result of poor roasting and with more experience ceased to be a major problem. The silica was a normal constituent of the feed and the working out of the problem became a matter of controlling its solubility. The obvious method to render the silica insoluble was by intensive roasting. This, however, met with total failure as such roasting resulted in silicates, probably zinc, soluble in the 13 pct acid used for leaching. Attempts were made to coagulate the fine gelatinous slime with addition agents. Glue, lime, starch, beef-blood serum and others were tried without success. All the suggested tried-and-tested means of operating the thickeners gave no consistently good results. Variations in leaching time, in addition of calcine to the leaching tanks, "conditioning" of the pulp by prolonged agitation, immediate discharge of the leach upon completion to avoid breaking up flocs were all tried and given up as ineffective. Byron Marquis, of Singmaster and Breyer, worked with the plant staff on a beaker scale until a leaching procedure was developed which gave consistent results and a promise of overcoming the difficulties which had plagued the plant operation. It was suggested that the difference in solubility of silicates and zinc oxide in sulphuric acid could be made use of in a leaching method where the acidity was controlled carefully. Such control is possible when acid is added to a slurry of calcine. This process reverses the normal procedure of adding calcine to a vessel of acid, hence the term "reverse leach" was applied. In this way, the overall acid concentration can be kept very low. In the tests made, it did not exceed 0.05 g per liter free sulphuric acid. Numerous advantages were realized when no silicates were taken into solution and later precipitated as a bulky gel. The gel had made reasonable thickening and filtration of the leach pulp and practical drying of the residue impossible. When the gel was eliminated, thickening rates were increased as much as five times. The volume of residue after thickening represented about 10 pct of the total leach pulp and had been as high as 95 pct when the gel was present. The thickened pulp was filterable and the filtered cake was dried readily after washing. The zinc extraction from the calcine was slightly lower. This was more than compensated for by the increase in zinc recovered in solution from zinc which had been trapped in the gelatinous residue. The amount of copper recovered was lower. However, the amounts of other impurities, such as arsenic, antimony, and germanium, taken into solution were lower. This was particularly true of antimony. Since the inception of reverse leaching, no concentrates have failed to yield solutions free of antimony even when present in the calcine to the extent of 0.2 to 0.3 pct. Oxidation of ferrous iron is a problem of reverse leaching. Ferrous hydrate does not precipitate at pH 5.3 to 5.4 where a leach is finished. The usual oxida-

Jan 1, 1952

By John T. Galey

A combination of two factors in addition to the current Federal drilling and price regulations reduced by 120 from I942 the number of new wells completed in southwestern Pennsylvania during the year. No new prospective area was found comparable to the Armbrust gas pool, Westmoreland Co., which accounted for a seventh of the last year's drilling, and it is considered doubtful whether, even if such a field had been discovered, the drilling contractors, who have been seriously affected by the manpower shortage, could have drilled many more wells than they did during the year. New wells totaling 445 were completed for a combined footage of over 1,250,000 Dry holes numbered 131 and had a footage of nearly 400,000. Old wells drilled deeper total 55, of which 17 were found nonproductive. Shallow Development Oil Oil completions yielded an initial of only slightly over one hundred barrels from 21 wells for about the same per well average as that of a year ago. However, 65 bbl. of this total came from two wells in two new strikes. The footage drilled of nearly 33,000 gives an average of nearly I00 ft. less per well than a year ago. Two old wells drilled deeper had a combined initial of only 4 bbl. The largest oil well of the year, 40 bbl., was found in the Speechley (U. Dev.) sand at a depth of 3492 ft. in German township, Fayette County. The location is several miles east of the nearest oil production hut as the area that could be occupied by a pool is fairly well delimited by drilling, the extent of this production would not appear to be large. The other notable oil production was found in the Dunkard (Penna.) sand, Cumberland township, Greene County, at a depth of 1065 ft. Here the first well had an initial of g bbl. and the second 25 bbl. However, a third proved dry, and as this area is also delimited by drilling, the pool doubtless will be of small area. Gas Gas completions yielded an initial of slightly over one hundred million cubic feet per day and new wells, totaling 303, account for all but four million of this volume. Old wells drilled deeper, numbering 35, found gas. The per well average in new drilling of approximately 320 M cu. ft. is nearly 165 M cu. ft. less than a year ago and the total footage is slightly over 830,000, which is about a quarter of a million feet less than in 1942. Average rock pressure of new completions is approximately 365 lb. per sq. in. The entire volume of new production is from the Upper Devonian or higher stratigraphic horizons. In Allegheny County, the grestest activity was in Forward and Plum townships. Wells there account for more than one half the completions. One large well was drilled in Forward township and an open flow of 3.623 million cubic feet was found in an old Gantz (U. Dev.) sand area. The top of the sand was encountered

Jan 1, 1944

By John T. Galey

A combination of two factors in addition to the current Federal drilling and price regulations reduced by 120 from I942 the number of new wells completed in southwestern Pennsylvania during the year. No new prospective area was found comparable to the Armbrust gas pool, Westmoreland Co., which accounted for a seventh of the last year's drilling, and it is considered doubtful whether, even if such a field had been discovered, the drilling contractors, who have been seriously affected by the manpower shortage, could have drilled many more wells than they did during the year. New wells totaling 445 were completed for a combined footage of over 1,250,000 Dry holes numbered 131 and had a footage of nearly 400,000. Old wells drilled deeper total 55, of which 17 were found nonproductive. Shallow Development Oil Oil completions yielded an initial of only slightly over one hundred barrels from 21 wells for about the same per well average as that of a year ago. However, 65 bbl. of this total came from two wells in two new strikes. The footage drilled of nearly 33,000 gives an average of nearly I00 ft. less per well than a year ago. Two old wells drilled deeper had a combined initial of only 4 bbl. The largest oil well of the year, 40 bbl., was found in the Speechley (U. Dev.) sand at a depth of 3492 ft. in German township, Fayette County. The location is several miles east of the nearest oil production hut as the area that could be occupied by a pool is fairly well delimited by drilling, the extent of this production would not appear to be large. The other notable oil production was found in the Dunkard (Penna.) sand, Cumberland township, Greene County, at a depth of 1065 ft. Here the first well had an initial of g bbl. and the second 25 bbl. However, a third proved dry, and as this area is also delimited by drilling, the pool doubtless will be of small area. Gas Gas completions yielded an initial of slightly over one hundred million cubic feet per day and new wells, totaling 303, account for all but four million of this volume. Old wells drilled deeper, numbering 35, found gas. The per well average in new drilling of approximately 320 M cu. ft. is nearly 165 M cu. ft. less than a year ago and the total footage is slightly over 830,000, which is about a quarter of a million feet less than in 1942. Average rock pressure of new completions is approximately 365 lb. per sq. in. The entire volume of new production is from the Upper Devonian or higher stratigraphic horizons. In Allegheny County, the grestest activity was in Forward and Plum townships. Wells there account for more than one half the completions. One large well was drilled in Forward township and an open flow of 3.623 million cubic feet was found in an old Gantz (U. Dev.) sand area. The top of the sand was encountered

Jan 1, 1944

Andrew Carnegie, America's best-known ironmaster and philanthropist, died at his home at Lenox, Mass., Monday, Aug. 11, after a three days' illness. A pioneer in the steel industry, he introduced into this .country the Bessemer process And formed the plans that have resulted in this country's supremacy in the steel markets of the world. Known throughout the world for his, gifts, he is also known to engineers as the donor of the home of their National Societies and as the founder of the Carnegie Institute of Technology, of Pittsburgh. For many years, also, he was an honorary member of the American Institute of Mining and Metallurgical Engineers, the American Society of Mechanical Engineers, and of the Engineers Club of New York. What he considered the secret, of his success is shown by the epitaph he wrote for himself, "Here lies a man who knew how to enlist in his service better men than himself." He was buried Thursday, Aug. 14, in Sleepy Hollow Cemetery, Tarry-town, N. Y., the funeral services being private, in accordance with his wish.

Jan 9, 1919

By GUY C. RIDDELL

ZINC, manganese, and aluminum received attention at the two nonferrous metallurgy sessions at the Annual Meeting. L.P. Davidson, general superintendent of the rebuilt Monsanto zinc plant, described its operation, which reflects Polish practice and is really a combination of electrolytic, Waelz, and retort procedure. Briefly, it embraces leaching of roasted concentrate with sulphuric acid, electrolysis of sulphate solution using Tainton lead-silver anodes with ?goulac? added to the electrolyte, treatment of tailing in Waelz kilns, and retorting of the recovered zinc oxide, casting furnace dross and residues. Recovery is good, equipment and maintenance costs low. Ferrate zinc that might be lost in the electrolytic process appears to be recovered as oxide in the Waelz treatment.

Jan 1, 1942

By R. W. Prouty, R. T. Green

The object of this paper is to describe, as concisely as possible, the methods of sampling and ore estimating used at the Copper Queen Branch, Phelps Dodge Corpn., as applied to the Copper Queen mines at Bisbee, Ariz. Because of the difference in occurrence, manner of prospecting, and methods of mining, the sampling and estimating practice falls into two divisions: That for the underground operations, and that for the Sacramento Hill steam-shovel operations. The orebodies of the Warren district may be divided into three main classes: Replacements of limestone, replacements of porphyry, and replacements of contact breccia. The first class is more or less intimately related to porphyry intrusions, although in badly fractured country this relationship may not be well shown. These orebodies are mainly oxide and carbonate ore and very irregular, both in size and outline, although usually roughly lenticular and following the bedding of the limestones. There is usually quite a sharp boundary between the ore and waste in the carbonate and oxide orebodies and sampling is not necessary to determine the limits of commercial ore. In the sulfide orebodies, it is exceedingly difficult, without sampling, to determine the boundary between commercial ore and the surrounding low-grade or barren pyrite. Calculations made a few years ago showed that these orebodies had an average thickness of 35 ft, As some of the orebodies are from 100 to 300 ft. thick, it can be seen that the smaller ones form a difficult prospecting and estimating problem. In the replacements in porphyry, both underground and in Sacramento Hill, the boundary usually cannot be determined without sampling. There is a gradual decrease in value until barren material is reached; this gradation may occur within a short distance or it may extend for several yards.

Jan 1, 1925

By Claus G. Goetzel

POWDER metallurgy is known as the art of producing metal powders and fabricating them in a nonfusion process by a simultaneous or consecutive application of pressure and heat under controlled operating conditions. Before the advent of powder metallurgy, the high melting points of the refractory metals and nonmetals made their manufacture and use practically impossible. Today, however, the uses of refractory materials in high-speed cutting tools, surgical instruments, brake linings, electrical contact switches, and filaments in incandescent lamps are commonplace in industry. Lately designers have even been turning to powder metallurgists to develop new techniques of fabricating refractory materials for extreme-service use in high-temperature zones of such modern products as gas turbines and jet engines. The new techniques being born will undoubtedly provide industry with a great number of new alloys and materials for future designing.

Jan 1, 1948

The Institute offers two distinct relationships to. students: one is an individual relationship as a Student Associate; and the other is a relationship with local organizations of students, known as Student Chapters of the AIME This individual relationship is set forth in Section 8 of Article I of the AIME Bylaws, as follows "A student in good standing in an approved school, who has been nominated by at least three instructors of the nominee (one of whom must be an Institute member), may affiliate with the Institute as a Student Associate by payment of $4.50 annual fee, for which he shall receive one monthly journal and be privileged to attend meetings of the Institute and to use the Engineering Societies Library and the Personnel Service A student may remain such until December 31 of the year in which he ceases to be in university residence as a student "

Jan 1, 1952

By P. H. Brace, N. A. Ziegler

THE study of the relations between gases and metals is one of perennial interest to all who are connected with the production of high-grade metallurgical products. The data reported here are the outcome of work of which the object is to determine the effects of dissolved gases upon the properties of metals and to gain a more detailed knowledge of the reactions between gases and molten metals, particularly iron, under definitely controlled conditions. We have attempted to reduce our margin of error by dealing with relatively large quantities of metal, from 4 to 13 lb. (2 to 6 kg.), and keeping the ratio of refractories to metal as small as practicable. The ingots produced are large enough to provide adequate material for making determinations of magnetic and other physical properties. In choosing the bell-jar type of furnace we were influenced by the results of considerable experimentation along the same general line which indicated that, for the scale on which we were to work, it was important to have the furnace structure independent of the vacuum enclosure. The use of a bell-jar surrounding the entire furnace accomplishes this and also gives great freedom of observation during operation and ready accessibility for the replacements which are necessary after each run. Our choice of analytical method was made in the light of the results secured by H. M. Ryder, who used a method similar in principle for the analysis of very small quantities of gas extracted from strips of metal heated electrically in high vacuum. We have presented some selected preliminary experimental data as being illustrative of the quantity and nature of the gases which occur in iron of different origins, but do not urge any hypothesis at this time. THE FURNACE Our furnace may be described as "a high-frequency induction furnace of the bell-jar type." It is similar in a general way to that described by Cain and Peterson' though we have introduced certain refinements of

Jan 1, 1928

By F. E. Bash

Constantan is an alloy of copper and nickel that is extensively used, under a number of trade names, as a resistance wire with a low temperature coefficient of resistance, and one of the elements of base-metal thermocouples, iron usually being the other thermoelement, although for low-temperature work copper is also used. Before the war, constantan was imported, in common with many other technical necessities. Since it required considerable time to receive the constantan after it was ordered, fairly large stocks were kept on hand; but after the beginning of the war no more was imported and the stocks of foreign material were exhausted about the same time that the steel and munition manufacturers began to need great quantities of it for thermocouples for the heat treatment of steel. To meet this demand, the International Nickel Co. began manufacturing constantan that met all the requirements of the users of resistance wire but did not give the same electromotive force against iron as the German material and consequently could not be used with instruments calibrated for a definite e.m.f.-temperature relation. It so happened that all the constantan made had an e.m.f. lower than that necessary to meet the specifications of the Leeds & Northrup Co. for whom this investigation was carried out. If some had been higher and some lower, good wire could have been obtained by a process of selection, but as it was no wire at all could be procured. To remedy this situation, a thorough investigation was started with the close cooperation of the International Nickel Co. and the Electrical Alloys Co. The specifications to which the constantan had to conform were that it should give an e.m.f. of 47.40 millivolts against pure iron at 1500" F. (816" C.) with the cold-junction temperature at 0" F., or a proportional e.m.f. at temperatures near 1500" F. The method of checking a wire was as follows: It was first welded to a piece of iron wire; Armco iron was found to be satisfactory but iron with greater than 0.1 per cent. carbon would give a lower e.m.f. against the same piece of constantan than pure iron. The couple was then insulated and the fire end was tied to the

Jan 1, 1921

By P. Payson

Intergranular corrosion in corrosion-resistant chromium-nickel steels has been widely discussed in the last few years. So far as the author knows, nothing has been published which definitely shows that this tendency can be eliminated, although suggestions have been made that a remedy is possible if certain specifications are satisfied. Strauss, Schottky and Hinnüberl suggested an increase in chromium content to an extent that would prevent the impoverishment of chromium on carbide precipitation sufficient to cause impaired corrosion resistance in the matrix. Pilling2 suggested an increase in nickel, so that the stability of the austenite matrix would be increased. Aborn and Bain3 say that "intergranular attack—may be eliminated by preventing carbide precipitation (e. g., by lowering the carbon content or somehow raising its solubility) or by precipitating it permanently under conditions which will not remove chromium from solid solution so drastically at any points." In a later paper Aborn and Bain4 state that many different metallic elements, tungsten, vanadium, copper, aluminum, molybdenum, titanium and zirconium, have been added in small percentages to increase the stability of these alloys, but that it has been reported that according to the copper sulfate test these added elements act only to retard the intergranular corrosion. and that increased nickel and chromium contents have similar effects. Newell5 showed that the lower the quenching temperature before reheating, the less severe was the intergranular attack.

Jan 1, 1932