Search Documents

By Strathmore R. B. Cooke

On the basis of experiments conducted on quartz using a bubble pick-up method, it was shown in an earlier paper1 that this mineral will preferentially adsorb hydrogen, calcium, or sodium ions, depending on the relative concentrations of those ions in the solution in which the quartz is immersed. For quartz particles ranging in size from 0.2 to 1 mm, it was demonstrated that the concentration of calcium in solution (assumed present as ions) necessary to completely activate quartz for flotation is given by the expression: Ca++ = [H+] X 106 + [Na+] X 10-3 In this expression, ionic concentrations are in mols per liter. It was further shown that the pick-up method is apparently more sensitive to changes in reagent concentration than the standard captive-bubble method, and that induction times are apparently much reduced. Since completing these earlier tests, a new type of cell has been constructed; this is shown in Fig 1 and 2. In Fig 1, A is a ground joint, B is a central tube reaching to within a few millimeters of the bottom of the cell, and C is a stopper which may be removed for reagent addition, and serves the further purpose of excluding carbon dioxide from the air during the test. The entire cell is constructed of Pyrex glass, and does not give the trouble experienced with the earlier cell, in which activating ions were released from the glass at high pH values. The only critical factor in the construction of the cell is the clearance between the central tube and the bottom of the cell. This clearance should be sufficiently small that the bubble can be pressed directly on the mineral grains lying on the bottom of the cell. In the pick-up tests to be described in this paper, the reagents used were all of C. P. grade, except the sodium oleate, which was Merck's "neutral powder." The quartz employed was water-clear vein quartz, sized on screens, cleaned with both hydrochloric acid and sodium hydroxide, and given a thorough final washing with distilled water. Experimental procedures were the same as described in the earlier paper. EFFECT OF SIZE OF QUARTZ ON PICK-UP To ascertain the effect of particle size on the adsorption of calcium ions, the quartz was sized from minus 14 plus 20 mesh through the intervening screen sizes to minus 270 mesh plus 400 mesh. Each size was thoroughly cleaned, and then tested in the cell at different calcium chloride and sodium hydroxide concentrations, and at a constant sodium oleate concentration of 20 mg per liter. All particles, within the size range given, exhibited complete pick-up within the curve expressed by the equation above. This presumably means, when the conditions imposed by the equation are satisfied, that this maximum is independent of particle size. However, it was found that the range through which partial particle pick-up occurred progressively broadened as particle size decreased. This is shown in Fig 3, in which curves B, C, and D show the limits at which pick-up just commences (as the pH is increased) for particles of minus 14 plus 28 mesh, minus 65 plus 100 mesh, and minus 270 plus 400 mesh size, respectively. These results indicate that for satisfactory activation, at any given pH, a lower calcium ion concentration is required for fine particles than for coarse particles. EFFECT OF HIGH ALKALINITY ON PICK-UP At calcium concentrations of between 1 and 10 mg per liter, and at high alka-linities, it was noticed that pick-up ceased as soon as calcium hydroxide commenced to precipitate. This effect was investigated at other calcium concentrations, with the same results. Solutions of calcium chloride, containing 105, 104, l03, and l02 mg of calcium per liter were made alkaline with sodium hydroxide until calcium hydroxide just started to precipitate, according to the following equation: CaCl² + NaOH -+ Ca(OH)2 + 2NaCl The beginning of precipitation was taken as that point at which either a faint opalescence appeared in the solution, or a Tyndall cone became ap-

Jan 1, 1950

By Robert Mehl

THE importance of the Widmanstätten structure to structure theory in metallography has been recognized by many writers.1 It is a structure produced by the precipitation of a new phase from a solid solution upon cooling as a result of changing solid solubility, and displays a characteristic appearance indicating a crystallographic relationship between the new phase and the original solid solution (Fig. 1). First discovered in 1808 by Alois de Widmanstätten2, the structure has been traced by analogy through many alloy systems. Particularly is this true of the steels. Sorby's classic work3 on the microstructure of iron and steel was in essence an attempt to explain the origin of this characteristic structure in meteoric iron. He observed in a Bessemer steel and in a cast-steel ingot structures which we now recognize as typical Widmanstätten figures.4 Osmond5 observed structures in a steel ingot analogous to those found in meteorites. Arnold and McWilliams6 obtained (and recognized) a

Jan 1, 1930

By M. E. Shank, J. Wulff

At the present time, the designer of dies for metal powder pressing is handicapped by relative ignorance of stress distribution and frictional effects at the interior surface of the die. Unckell was the first to develop a method for the study of wall friction. He used three Brinell balls on which the die rested during pressing. The total frictional wall force was determined by the size of impression these balls left on a soft metal plate. Since the method does not give radial pressures, or distribution of such pressures, coefficients of friction could not be determined. Although Unckel measured density distribution, he was not able to determine radial or shear stresses. Shaler2 has proposed theoretical expressions for the stress and density distribution within cylindrical compacts during pressing, in accordance with the experimental results of Kamm, Steinberg, and Wulff.3 By application of Siebel's method,4 Kamm et a13 plotted stress trajectories for two compacts. From the stress trajectories they calculated coefficients of friction from point to point along the die wall. As pointed out by Shaler in the discussion of Ref. 3, these values are based on progressive point-to-point calculations on finite size grid squares across the compact. In the region of the die wall such calculated values may therefore have considerable cumulative error. The purpose of the present paper is to develop an experimental method by which the nonhydrostatic pressures and shears acting on the interior wall of a cylindrical die can be measured. Such measurements can then he correlated with existing data to aid in the explanation of the pressing process. The method used is based on the elastic: properties of the thick-walled tube used as the die. The principle of super-position of force systems on an elastic body is assumed to hold. Electric strain gauges were mounted in adjacent positions on the exterior die wall in order to get an exact measurement of the variation of tangential strain over the length of the die during pressing. While in this paper, measurements in terms of only tangential strains are considered, it is well to note that similar calculations may be set up for axial strains. The latter are not preferred, since they tend to be smaller than the tangential strains and therefore permit less sensitive measurements. Discussion in this work is restricted to compacts pressed from both ends, since the elastic deformation of the die is then more amenable to analysis. Before choosing the electric strain gauge method, a more direct line of attack was considered and discarded. The discarded idea was the insertion of a pressure gauge through a hole in the die wall.* The gauge would have been in the form of a small piston. If pressure were exerted against such a gauge, it would move outward along a radius of the die. One disadvantage of the scheme is its inability to measure shears along the die wall. Another more serious disadvantage is the disturbance caused by the device itself. It would serve to change the forces it was designed to measure. No matter how small the movement of the gauge, when pressure is applied a discontinuity would exist in the wall surface at that point. Due to the stress concentration caused by the hole, abnormal deflections of the die wall would occur around the gauge. During pressing, powder would be forced into the resulting depression. The depression would then become larger with increasing compacting pressure. Powder, not being a fluid, is capable of supporting shear. The ease with which it would flow into the die wall depression to further move the piston is an indication, not of the radial pressure at that point, but of the state of shear retarding the movement. Thus the "pressure" gauge is really a criterion of flowability, and of the capability of the powder to support shear. For these reasons, it was decided that the electric strain method, herein employed, was more reliable, if more indirect. The gauges and lead wires, mounted on the external die wall do not in any way affect the behavior of the metal powder or the die during pressing. Theory of the Method THE EFFECT OF RADIAL PRESSURE ON THE DIE WALL Effect of a Single Small Band of Hydrostatic Pressure Consider a die which is a thick-walled cylinder of outer radius R. and inner radius Ri. If over a small finite length L there is a normal pressure P, a tangential strain distribution at the outer wall results. This is shown schematically in Fig 1. The exact shape of the curve may he predicted by an extension of the theory of a semi-infinite beam on an elastic foundation.6 This

Jan 1, 1950

By K. Verghese, R. W. Rousseau, R. P. Gardner

A radioactive tracer method and a size-discretized, mass balance model are formulated and demonstrated in a feasibility experiment for the determination of crystal growth rates in MSMPR crystallizers. The system studied is aqueous KN03 with K-42 as the radioactive tracer. The results indicate that the method should prove to be very valuable for this application, particularly when systems exhibiting size-dependent growth rates are of interest. An indicated refinement to the tracer method is the simultaneous use of an additional tracer in the liquid to determine the amount of radioactivity from the liquid that is adsorbed on the samples of filtered crystals.

Jan 1, 1980

By W. M. Weigel

WHILE electric lamps both of the cap and hand type are being introduced into many mines requiring the use of safety lamps, the oil-burning safety lamp is still used in the great majority of cases, and even where the former are used the latter must continue to be employed when testing for gas. It is not the intention to discuss here the relative merits of the two types, but simply to give a comparison of the illuminating effect or candlepower of several kinds of ordinary safety lamps used for general work and for testing. Few data have been published in recent years on this subject and because of this it is hoped that the following information may be of some interest and value. The lamps tested were in all cases. of standard size and in good condition, all practically new, and were selected from a collection of about 100 with a view to obtaining results on as many different common types as possible. With the exception of the gasoline-burning lamps, five different oils were used in each lamp to determine whether -particular oils were suited to particular lamps and whether there was any great difference in the illuminating power of the different oils, or whether some oils would maintain their illuminating power better than others throughout a working period of 8 hr. No attempt was made to determine the amount or cost of oil burned by each lamp, but the condition of the lamp, wick, glass, and gauzes was noted after each test.

Jan 8, 1916

By J. T. Raleigh, D. L. Flock

This study investigated the nature of formation plugging with bacteria and attempted to relate its characteristics to physical rock properties. Fifteen core samples of four specific formation types were defined and plugged using a commonly occurring, uniform sized dead bacteria, Bacillus subtilis. Two of the formation types were fairly uniform-grained sandstones and two were heterogeneous carbonates. The injection rate and concentration of solids in the brine were held constant during the test runs. The pore geometry factor G was a significant petro-physical rock characteristic for correlation with depth of plugging, but lacked importance as a parameter for rate of plugging. Although the G factor may not completely describe porous rock geometry for plugging predictions, for reservoirs with multi-pore systems, there is evidence that the pore geometry factor might form a basis for establishing injection water specification in more llornogeneous reservoirs with only primary porosity development. INTRODUCTION GENERAL PURPOSE Injecting water into oil-bearing formations to increase recovery is common practice in the petroleum industry. One of the most serious operational problems involved with water injection wells is the tendency of the porous rock immediately adjacent to the injection wellbore to plug partially. This results in increased injection pressures and/or a decrease in the rate of injection. This plugging in injection wells can result from a number of causes, including bacteria contained in the injected water.1 The purpose of this work was to investigate the nature of injection plugging with bacteria and to attempt to relate its characteristics to physical rock properties. Many variables exist in research of this type, so, to reduce them, injection rate and concentration of bacteria in brine were held constant. The bacteria used for plugging was a uniform-sized, dead bacteria, Bacillus subtilis, a micro-organism commonly found in water, air and soils. Four specific porous rock types were plugged—two consolidated sandstones and two heterogeneous carbonates. The experimental work involved two distinct phases. The first concerned determining the physical rock properties and the second was the experimental work of actually plugging the selected core samples. PORE GEOMETRY FACTOR Capillary pressure is necessary to displace a wetting fluid from a capillary opening with a nonwetting fluid. The factors which govern capillary pressure are the surface or interfacial tension of the fluids involved, the system wettability and the equivalent pore radius. Thus: P,= 2ucososrd..........(1) Thomeer used the idea that the location and shape of the capillary pressure curve reflect characteristics of the pore structure of any porous media sample.' He presented the mathematical description of capillary pressure curves and of indicated differences in pore geometry of samples. where G = pore geometry factor PC = capillary pressure Pi = displacement pressure (V,)p, = fractional bulk volume occupied by the displacing fluid at any capillary pressure (V,), = fractional bulk volume occupied by the displacing fluid at infinite pressure or total interconnected pore volumes. The shape of the curve is defined by the pore geometry factor G. The curve shape is related directly to the sorting and interconnection of the pores of the sample. The location of an infinite number of curves can be defined by the same asymptotes. However, these curves differ in shape, each curve being described by a specific value of G. Thus, the description of a curve is unique when, in addition to the position of its asymptotes, its shape is defined. These curves can be used graphically to determine the characteristic parameters of any arbitrarily located curve. Those parameters that can be approximated from any capillary pressure curve are: (1) total interconnected pore volume, represented by (V,),- ; (2) extrapolated displacement pressure, the abscissa axis; and (3) pore geometry factor, by the curve shape. PROPERTIES OF BRINE AND BACTERIA The fluid used throughout this study was an aqueous solution of sodium chloride, 25,000 ppm by weight. The addition of salt to fresh water was intended to eliminate clay swelling in the sandstone cores and to retard leaching in the limestone cores. The viscosity of the brine solution at 100F, the temp-

Jan 1, 1966

By R. E. Boni, G. Derge

Application of surface tension measurements has been made to molten silicates in order to determine the effect of sulphur upon the surface tensions of synthetic blast furnace slags. In melts with the same molar ratios of AI2O3 + SiO2 to the basic oxides BaO, CaO, and MgO, the surface tensions increase in the order of oxides listed. Sulphur lowers the surface tensions of the basic BaO, basic CaO, acid BaO, acid CaO, and acid MgO slags in that order; and the concentration of excess sulphur at the slag surface increases in this same order of slags. The rate and amount of desulphurization of iron by these slags is favored by a low excess surface sulphur in the slag. IN a previous paper,1 the authors discussed the applications of surface tension measurements of molten silicates to problems of metallurgical interest. Of major importance is the aid that such studies lend to forming a working concept of slag structure. Since the ability of a slag to desulphurize metal depends strongly upon its composition,2"4 fundamental information about the structural differences between various slags which contain sulphur should aid the development of better desulphurizing media. For that reason, the present investigation concerns the effect of sulphur upon the surface tensions of synthetic blast furnace slags. Experimental Procedure , The maximum bubble-pressure method was used to measure the surface tensions of synthetic blast furnace slags in the temperature range 1300° to 1600°C. The method is based upon the equation which was developed by Schrödinger5 from a consideration of the forces of hydrostatic pressure and surface tension of a liquid which oppose bubble formation when a gas is forced through a tube immersed in the liquid. where y is the surface tension between argon and slag in dynes per centimeter; g is the gravitational constant, centimeters per second2; H is the manometer reading in centimeters; s2 is the density of manometer fluid in grams per cubic centimeter; S1 is the density of the medium in grams per cubic

Jan 1, 1957

By A. Lawley S. Schuster

The tensile behavior of copper foils prepared from rolled bulk material has been studied over the thickness range 2 to 53 , and for a range of pain sizes. For foils of comparable grain size, having the cube texture and tested along (100), yield strength increases with decreasing foil thickness t below -26p, with a corresponding decrease in ductility. Deformation occurs in the form of localized slip clusters distributed throughout the gage section. To the extent that the tensile strength (10 to 18 kg mm-) is unaffected by foil thickness, and that the foils possess fair ductility, the stress-strain behavior resembles that of bulk material rather than that of whiskers or evaporated films of comparable dimensions. The dependence of yield strength o on foil thickness t below -26p is of the form: oy = oo + kt-1/2. Possible explanations for the stress increase are considered based on 1) the dependence of active dislocation source length on foil dimensions, 2) the locking of surface sources, or the blocking of mobile sources at the surface due to surface film. It is now well-established that filamentary whiskers of many materials show exceptionally high strength compared with bulk crystals.'-11 As the diameter of the whiskers decreases to -1, the observed fracture strength approaches, and in certain cases exceeds, the calculated shear stress for the nucleation of slip in a perfect crystal.' In general, the stress-strain curve is entirely elastic, with strains at fracture approaching 1 pct. Similarly, thin films12-24 of evaporated or electrodeposi-ted material have been shown to possess tensile strengths three to seven times that of bulk material, with total strains at fracture -1 to 2 pct. In the present study, attention has been directed to the room-temperature tensile behavior of thin foils of copper over the thickness range 2 to 53, prepared from rolled bulk material. Yield stress, ultimate tensile strength, elongation to fracture, and work-hardening behavior are measured as a function of grain size and foil thickness. Structurally such foils are superior to either evaporated or electrodeposited films, and in the recrystallized condition exhibit considerable ductility. Apart from preliminary work by Sumino and Yamamoto25 on the work-hardening behavior of rolled and recrystallized copper foils, no systematic tensile studies have been carried out on material of this form. EXPERIMENTAL PROCEDURE Tensile specimens were prepared from 99.995 pct purity rolled copper foils of thickness 2, 6, 12, 26, and 53, obtained from the Hamilton Watch Co., Lancaster, Pa. Irrespective of specimen shape, it is necessary to use tensile foils with edges free from notches or tears. To this end, any form of cutting operation was excluded, and the tensile foils prepared using a photoengraving process, the details of which are described elsewhere.26 Since tensile data are required under conditions of uni-axial stress, the specimen shape is extremely important. Ideally, the foil should be infinitely long, allowing a gradual taper from the grip area to the gage section; however, from a practical standpoint, long foils are easily damaged during testing. A modified tensile specimen was therefore selected having a parallel gage section 1.25 by 0.20 in. with a tapered shoulder section increasing to 0.5 in. at the grips, and an over-all length between grips of 4 in., Fig. 1. In practically all tests, these foils fractured within the parallel gage section. By approximating the foil contour (Fig. 1) to a hyperbola it is possible to analyze the stress distribution in the tensile foil using two-dimensional elasticity

Jan 1, 1964

By P. H. Dudley

The piping and segregation of ingots of steel is a comprehensive subject, and must be studied in reference to the different grades of soft, medium, and hard steel, rather than to discuss it in a general manner, as though applicable to all grades. Rail steel, however, will receive the most consideration in this paper, for the wheel-loads of the motive power and rolling stock have doubled from 1890 to 1910. Steel rails and tires which were efficient under the light loads, became less serviceable under the double wheel-loads, quadrupled tonnage, and higher speeds. Bessemer Steel. Bessemer steel of from 0.10 to 0.15 per cent. of carbon, for splice-bars, spikes, and tie-plates, rises in setting, and is cast in bottle-mouthed molds, which must be capped to prevent an overflow from the top. This grade of steel rises in the molds and makes a longer ingot than the volume of molten steel when first teemed. The ingots which are allowed to cool and then cut open, show, particularly in the upper part, large occluded blow-holes, and when they are not oxidized or do not contain foreign matter, weld more or less completely when the steel is rolled or forged above 1,100° C., and it is in this way that the blow-holes are closed in the low-carbon steels. Boiler-Plate and Fire-Box Steel. These grades often contain more or less minute laminations, which are the remains of small blow-holes forming after the setting metal has reached a pasty condition. The blow-holes in the low-carbon steels have not been prevented by usiug deox-idizers, though the ingots are slightly improved so far as the soundness of the steel is concerned. This grade of steel also rises in the molds in setting.

Jan 1, 1914

By H. O. Hofman

THE leading antimony mineral is stibnite. In smelting stibnite ore two processes are available, precipitation and roasting-reduction. The former is suited only for high-grade ores. As low-grade ores are more common than high-grade, roasting-reduction is of greater importance than precipitation. In the roasting process the aim may be to leave the oxidized antimony in the ore, or it may be to volatilize as much of the antimony as possible, collect the volatilized oxide as a rich intermediary product and smelt it for antimony, leaving the gangue poor enough to be considered a waste product. Whichever way the roast is conducted certain difficulties inherent in stibnite are encountered. These are: 1. The low melting point of stibnite which; according to Pelabon,1 is 550°C., according to Wagemann2 540°C., and according to Borgström3 546°C. 2. The ignition temperature: According to Friedrich,4 stibnite, if heated in air, begins to oxidize at 290°C. if the size of a grain is 0.1 mm. in diameter; at 343°, if 0.1 to 0.2 mm.; and 430° if 0.2 mm. 3. The fusibility of a mixture of Sb2S3 and Sb203 which in the form of kermesite (Sb2S3)2.Sb203 melts at 517°C.5 4. The volatility of Sb2S3 and Sb203, for which no numerical data appear to exist, although practical experience has shown that they are volatile at low temperatures.

Jan 1, 1916

By John Rogers

The goal of a detailed quantitative understanding of the variables insulfide flotation in terms of established, or new, scientific principles is still distant, although there has been a good beginning in the past 50 years with more rapid progress since 1930. Advances have paralleled closely those in other branches of surface chemistry and the development of a series of experimental techniques such as contact angle, surface area measurement, radioactive tracers, infrared spectra, electron diffraction, monolayer, and electro- chemical methods of investigation. The second editions of books by Sutherland and Warkl ( 1955) and Gaudin2 ( 19571, are detailed accounts of this progress. The complexity of sulfide mineral flotation systems is indicated by Sutherland and Warkl who list 32 variables of flotation, of which only 22 can usually be controlled by the metallurgist. A consequence of this multiplicity of variables, many of which may be specific to each particular ore, is that ways of floating sulfide minerals from new ores are still developed empirically. How- ever, this review will try to show how the chemistry of the function of frothers, collectors, depressants, and activators in sulfide flotation is being steadily unravelled. Chiefly, it will be concerned with the interaction of pure soluble compounds with individual sulfide minerals, the surfaces of which are often not stoichiometric for several reasons discussed by Plaksin.3 As a result, for example, a freshly cleaved galena surface has cathodic and anodic areas which have different degrees of oxidation and different reactivity to- wards collectors like xanthate. Such complicating considerations should be remembered in the subsequent discussion of pure minerals. THE NEED FOR FLOTATION REAGENTS After considerable controversy it has been established with a few exceptions that unoxidized, uncontaminated sulfides will not float. Moreover all flotation plants recovering sulfide minerals use collectors which are removed from the circuit with the sulfides. Gaudin, Miaw, and Spedden4 have discussed the relation between the crystal structure of solids and the native floatability of the exceptions mentioned above. A second question which has been much explored is the nature of the surface on which a collector like xanthate is adsorbed or reacts. Is this the un- changed surface of the sulfide mineral, or does the adsorption depend on the initial oxidation of the sulfide surface ? Sutherland and Warkl and Gaudin2 discuss the work of Taggart5 and others on this question without reaching any other conclusion than that oxygen was important.

Jan 1, 1962

ATHOUGH the open-hearth charge contributes CO, CO2, and water vapor to the combustion gases and absorbs oxygen from them, in the main the thermal effects in the melting charge and molten bath can be considered independently of those in fuel combustion, the latter being regarded simply as the source of any extra heat required to finish a heat of steel. First of all, it should be remembered that a large percentage of the heat supplied to the bath is furnished by oxidation of the various elements in the charge itself. If this charge consisted of 80 to 100 per cent of hot metal and the oxidation were obtained by blowing in air or oxygen, as is the case in the Bessemer converter, then the net heat absorption would be negative, that is, the bath would contribute part of the heat required to keep the melting chamber hot, in addition to that contained in the finished steel and slag. In actual open-hearth practices, probably the nearest approach to this is in the duplex furnace, charged with Bessemer-blown metal and some hot metal, where very little heat is required to complete the refining and nearly all the heat energy from fuel combustion is used to keep the roof and walls of the melting chamber up to around 2900 to 3000°F. (1600 to 1650°C.) so that the bath will not cool off during the refining. The other extreme is with all-cold charges containing around 80 per cent steel scrap and 20 per cent cast iron or cold pig iron, in which case a very large proportion of the heat in the bath at tap is supplied from the fuel combustion. THERMAL EFFECTS IN MELTTNG In the previous chapter it was pointed out that in a typical heat, the fuel furnishes about four million B.t.u. per ton of steel produced. The heat required for the metallurgical processes is not easily defined in useful manner (as is shown later), but it ranges downward from about one million B.t.u., depending not only on the charge but on the manner of calculation. In any event this requirement appears quite small in comparison with the heat furnished by the fuel and invites

Jan 1, 1944

By B. B. Cox

The principal event during 1936 was the sale of Mosul Oilfields, Ltd. to Mosul Holdings, Ltd., a British company with French and American participation, and the expansion of its wildcat activities to untested structures on its West Tigris concession. Mosul Holdings continued the exploration of its low-gravity Qaiyarah-Najmah-Jawan-Qasab field. The Iraq Petroleum Company's systematic exploration and exploitation of its Kirkuk field was continued on a scientific unitized basis. Pressures and gas-oil ratios remained satisfactory. All wells were produced by flowing. A stabilization plant large enough to supply the 4,000,000-ton pipe line to the Mediterranean was completed at Kirkuk about the close of the year and only sweet oil is now being exported. The Khanaqin Oil Co., Ltd., a subsidiary of the Anglo-Iranian Oil Co., Ltd., continued the normal exploitation of its Naft Khaneh oil field, refining and marketing through the Rafidain Oil Co., Ltd. for local Iraq market. This field lies partly on the Iraq side of the boundary and partly on the Iranian side, the latter portion being known as Naft-i-Shah. Only the Iraq side is considered in this paper. Slightly more than 30,000,000 bbl. of crude was produced in Iraq during 1936. The I.P.C. exported all crude sold outside of Iraq and showed an increase of about 2,500,000 bbl. over the preceding year. Crude production in Iraq for export in 1934 was 7,096,669 bbl.'; in 1935 it was 27,014,904 bbl. and in 1936 it was 29,521,053 barrels.

Jan 1, 1937

By E. P. Jennings

Large deposits of titaniferous iron-ore occur at Caribou, an old silver-mining camp in Boulder county, Colo., 17 miles west by south of Boulder, and a few miles northwest of the tungsten-mines. Professor Regis Chauvenet1 published a part analysis of the ore many years ago, but gave no description of the wall-rock. Caribou hill, which contains both the silver-bearing veins and the iron-ore deposits, is a low dome of gabbro surrounded by the Archæan schists and gneisses of the Front range of the Rocky mountains, the peaks of which, a few miles west of Caribou, attain an elevation exceeding 12,000 ft. The gabbro stock is roughly elliptical in outline, with approximate diameters of 1 and 3 miles. The crest of the dome is 10,500 ft. above sea-level, and the town and ore-cleposits are 500 ft. lower. Outcrops of the iron-ore occur in the town and extend NW. for 2,000 ft., where they disappear under the swampy meadows of Caribou park. Portions of the deposit are covered by drift, but one continuous outcrop is 900 ft. long and from 200 to 250 ft. wide. A second deposit is 0.25 mile south of the town along the eastern slope of the hill. It is not as well defined as the north bed, but is approximately 1,000 ft. long and from 100 to 200 ft. wide. The easily disintegrated ore does not form prominent outcrops, but the outlines of the deposits are readily traced by the large amount of ore fragments that cover the ground. Trenches and pits sunk on the outcrop expose a roughly banded magnetic iron-ore, with pyroxene as the principal gangue-mineral. The Gabbro. This rock was classified in the field as a gabbro from the presence of pyroxene and striated feldspars, and for convenience the field-name will be retained.

Jan 1, 1913

By ANDREW McVILLIAM, WILLIAM H. HATFIELD

AT the 1902 May meeting of the Iron and Steel Institute, the, authors presented a paper on " The Elimination of Silicon in The Acid Open-Hearth," wherein they recorded a few typical examples of certain Siemens charges out of a very large number specially watched for the purposes of that research. The main deductions drawn from those experiments have been accepted in all the intelligent criticism during or after the discussion on the paper. One opinion, however, was rigidly held by all who mentioned the matter, with the single exception, perhaps, of Mr. Lange, and that was the necessity for the attainment and the maintenance of an abnormally high temperature in order that the percentage of silicon in the metallic bath might increase, or that an unusually large proportion of silicon might be retained in the metal. The original decision was ar-rived at on the results of scores of trials, and has since been the subject of frequent experiment. The authors still retain their opinion that although, naturally, a higher temperature will accelerate the (probable) action between the carbon of the steel and the excess silica of the slag, they then fairly proved, and have now abundantly confirmed the fact, that around the temperatures occurring in Siemens steel-making practice the chemical composition of the slag, particularly with regard to its acidity, is the factor which determines whether the percentage of silicon in the molten steel shall increase or decrease. In the discussion in 1902 Mr. Saniter called attention to Mr. H. H. Campbell's work, and in the reply the authors also mentioned that of Messrs. Winder and Brunton of 1892, the two

Mar 1, 1905

By Paul C. Merritt

Chrysotile asbestos producers in Quebec may soon experience a unique situation-i.e., strong competition from American ore sources for the short fiber market west of the Mississippi River. This com- petition will be forthcoming from Copperopolis and Coalinga, two deposits now being developed on opposite flanks of the San Joaquin Valley in central California. The combined output now planned from both deposits is 100,000 tons annually, equivalent to about 50% of the annual market demand in the western, central and Gulf States, and more than twice the tonnage sold in 1960 by all other American asbestos producers combined. The principal companies involved in these new undertakings are Jefferson Lake Asbestos Corp. (subsidiary of Jefferson Lake Sulphur Co.), Hidden Splendor Mining Co., Coalinga Asbestos Co. (Johns- Manville Corp. in conjunction with Kern County Land Co.), Union Carbide Corp., and Asbestos Corp. Ltd. Jefferson Lake's principal interest is at Copperopolis where the company's new 70,000-ton per yr mill recently went on stream. The company also holds some claims at Coalinga, but this latter area is better known as the site where Hidden Splendor, Coalinga Asbestos Co. and Todd Industries (a local company) have established operating mines and mills capable of turning out 30,000 tons of fiber each year. Coalinga is also the site of exploration by Union Carbide Nuclear and Asbestos Corp. Ltd.

Jan 9, 1962

PRESIDENT AND DIRECTOR DONALD B. GILLIES CLEVELAND, OHIO PAST PRESIDENTS AND DIRECTORS R. C. ALLEN CLEVELAND, OHIO D. C. TACKLING SAN FRANCISCO, CALIF. TREASURER AND DIRECTOR KARL EILERS NEW YORK, N. Y. VICE-PRESIDENTS AND DIRECTORS H. G. MOULTON NEW YORK, N. Y. HARVEY S. MUDD Los ANGELES, CALIF. PAUL -D. MERICA NEW YORK, N. Y. WILFRED SYKES CHICAGO, ILL. WILLIAM B. HEROY HOUSTON, TEXAS HENRY KRUMB NEW YORK, N. Y.

Jan 1, 1939

By J. H. Swisher

The rate of internal sulfidation of austenitic Fe-Ti alloys in H2S-H2 gas mixtures is controlled primarily by sulfur diffusion, with counterdiffusion of titanium playing a minor role. At temperatures below 1100°C, enhanced diffusion along grain boundaries becomes important. The rate of internal sulfidation at 1300°C is approximately equal to the rate computed from the sulfur diffusion coefficient. The diffusion coefficient of titanium in y iron has been determined from electron microprobe traces in the base alloy near the subscale interface. The solubility of sulfur in Fe-Ti alloys has been measured in the temperature range from 1150° to 1300°C. The equilibrium sulfur content is found to increase with titanium content, due to the large effect of titanium on the activity coefficient of sulfur. The Ti-S interaction becomes stronger as the temperature decreases. TITANIUM as an alloying element in stainless steels is an effective scavenger for interstitial impurities, carbon in particular. Titanium is known to form stable sulfides; however extensive thermodynamic data on the Ti-S system are not available. Schindlerova and Buzek1 have shown that the Ti-S interaction in liquid iron is moderately strong. There have been no previous studies of the Ti-S interaction in solid iron. Internal sulfidation of Fe-Mn alloys was the subject of a recent investigation by Herrnstein.2 He found the rate of internal sulfidation to be an order of magnitude greater than predicted from available solubility and diffusivity data. A satisfactory explanation for the discrepancy could not be given. In the present study, the solubility of sulfur in austenitic Fe-Ti alloys was measured using a standard gas equilibration technique. Fe-Ti alloy specimens were also internally sulfidized. The rate of internal sulfidation was measured as a function of temperature and alloy composition. Supplementary electron micro-probe measurements were made to provide additional information on the nature of the internal sulfidation process. EXPERIMENTAL The starting materials were alloys containing 0.12, 0.24, 0.38, and 0.54 wt pct Ti. The alloys were made in an induction furnace by adding titanium to electrolytic iron that previously had been vacuum-carbon-deoxidized. The major impurity in the alloys as determined by chemical analysis was carbon. The carbon content of the alloys averaged about 100 ppm; metallic impurities were presented in concentrations of 50 ppm or less. Specimens were made in the form of flat plates, 0.03 by 2 by 4 cm for the equilibrium measurements and 0.5 by 1.5 by 3 cm for the rate measurements. The experiments were performed in a vertical resistance furnace wound with molybdenum wire and containing a recrystallized alumina reaction tube. In the gas train, flow rates of the reacting gases were measured using capillary flow meters. The source of H2S was a mixture of approximately 2 pct H2S in H2, which was obtained in cylinders from the Matheson Co. A chemical analysis was provided with each cylinder. The H2-H2S mixture was diluted with additional hydrogen to obtain the desired ratio of H2S to H2, and the resulting mixture was diluted with 30 pct Ar to minimize thermal segregation of H2S in the furnace. Argon was purified by passage over copper chips at 350°C and subsequently over anhydrone. Hydrogen was purified by passage over platinized asbestos at 450°C and then over anhydrone. The H2-H2S mixture was purified by passage over platinized asbestos and then over Pas. The samples used in the solubility measurements were analyzed for sulfur by combustion and iodometric titration. The subscale thickness in the internally sulfidized samples was measured on a polished cross section, using a microscope with a micrometer stage. Electron microprobe traces for titanium in solution were made on several samples that had been internally sulfidized. A Cambridge microanalyzer was used, and the known titanium content at the center of the specimen was used as a calibration standard. The procedure for the microprobe measurements will be described further when the results are presented. RESULTS AND DISCUSSION Equilibrium Data. Fig. 1 shows the sulfur concentration as a function of gas composition for three alloys equilibrated at 1300°C. The dashed line is based on data published by Turkdogan, Ignatowicz, and pearson3 for pure iron. The breaks in the curves are the saturation points for the alloys. The fact that the initial slope decreases with increasing titanium content indicates that titanium interacts strongly with sulfur in solution. To obtain information on the composition of the precipitating sulfide phase, the measurements described in Fig. 1 were extended to higher sulfur partial pressures. These results are shown in Fig. 2. (The initial portions of the curves are reproduced from Fig. 1.) The highest PH2s /pH2 ratio used is believed to be below the ratio required for the formation of a liquid sulfide phase. Time series experiments were used to study the approach to equilibrium in the samples. It was found that equilibrium with the gas phase was reached in less than 4 hr at 1300°C.

Jan 1, 1969

"The Butte, Anaconda & Pacific railway extends from Butte to Anaconda. The electrification comprises 30 miles of main line single track, and includes sidings, yard and smelter tracks. When complete the electrified trackage will total about 90 miles on a single track basis.The traffic conditions are unusually severe as they consist principally of hauling copper ore from the Butte mines to the smelters at Anaconda, as well as hauling all the mine supplies, lumber, etc., in both directions; this traffic amounts to approximately 5,000,000 tons of freight per year. The maximum grade against the load is .3 per cent and the maximum train consists of 50 loaded steel ore cars, weighing 3,400 tons. .The locomotive units, two of which will be used for freight trains, weigh approximately 80 tons each. In addition to the freight business, there will be a certain amount of passenger traffic.The power for operating the Butte, Anaconda & Pacific railway is generated by, the Great Falls Power company, and is transmitted to the sub-stations at 100,000 volts. The synchronous motors are supplied with power at a potential of 2,300 volts, 60 cycles, 3-phase. Voltage regulators are installed in each sub¬station to secure the benefit of synchronous condenser effect of the motors.The passenger and freight locomotives are exactly similar, with the exception of the gearing.The roller pantograph mounted on the top of the cab is operated by air from the engineers position.The adoption of the 2,400-volt apparatus for so important a system, where the conditions of operation are so severe, is interesting of itself, as indicating the trend that future electrifications of importance may follow. A trolley potential of 2,400 volts was only adopted after a thorough investigation of other systems already in operation."

Jan 1, 1913

By W. A. Backofen, B. C. Wonsiewicz

The Plasticity transition in magnesium was studied by plane-strain compression of single crystals and polycrystalline material at temperatures from about 20" to 307°C. Reduction of single crystals along the c axis was accommodated by twinning on {1011) and retwinning on (10 12}, followed by basal shear in the doubly twinned volume. Deformation in that mode can result in sufficient independent shears for arbitrary shape change. Fracture in c axis compression, below about 100°C, has been related to excessive shear caused by unloading from the stress for {1011} twinning (-50 ksi at 20°C) to that for slip within the twin (-3 ksi); ductility follows from heating because the stress difference is lowered and the twin volume, in which elastic strain energy is dissipated on unloading, is increased. The stress for (1011) twinning is strongly temperature-dependent but not given by a critical resolved shear stress law. The latter is attributed to the influence of stress concentration from prior intersecting shear on nonbasal planes, the former to the temperature dependence of the preliminary slip. THE basic symmetry of hcp crystals has the effect of limiting the number of independent slip systems and making twinning an important deformation mechanism. The general result in wrought polycrystalline aggregates is a more or less sharply developed texture (or preferred orientation) which underlies a strong anisotropy in mechanical behavior. Knowing how the one influences the other is essential background for the use of such materials. Magnesium was of interest in this work because of the unexplained plasticity transition that it undergoes somewhere in the neighborhood of 200°c.''~ At lower temperatures plastic deformation before fracture in polycrystalline material is limited, while at higher temperatures extensive deformation is possible. The transition temperature commonly determines the lower limit of the range in which magnesium is worked. The limited ductility can be traced to a lack of independent crystallographic shears. A minimum of five are required for arbitrary shape change.' Around room temperature, however, slip on all known systems provides only four.' In each case, the slip direction is in the (0001) basal plane so that slip does not allow strain along the c axis. With increasing temperature, more slip occurs on the ( 1011) pyramidal plane and the ( 1010) prism plane but without change in direction.'?' Thus, that development alone cannot explain the transition temperature.

Jan 1, 1968