Search Documents

By E. I. Larsen, E. F. Swazy, F. R. Hensel

HIGH strength, high-conductivity copper-base alloys have found considerable use in the resistance welding and electrical industry in the form of castings, forgings, or wrought products. There are a number of parts utilized by these industries which would lend themselves to manufacture by powder metallurgical methods provided the required physical and electrical properties are obtainable with such methods. The present paper describes the results of a study of certain copper-base powder metallurgical products susceptible to precipitation hardening. COPPER POWDERS The general types of commercially available copper powders are flake, spherical and electrolytic. Micrographs of these three types are shown in Figs. I, 2 and 3. The difference in particle shape is pronounced and obvious. The type of powder used is determined, or at least indicated, by the final properties desired in the finished article. The type of powder employed during the present investigation was electrolytic powder shown in Fig. 3, and was chosen because of its particular adaptability to the work described in this paper. The screen and chemical analyses of this powder are shown in Table I. In the preparation of compacts of high electrical conductivity, the purity of the copper powder is of importance in addition to other factors, such as density and the state of internal stresses. These variables were studied briefly by pressing a number of compacts to various pressed densities, sintering them for one hour in hydrogen at 975°C. and repressing. The size of the finished compacts was ¼ by ¾ by 8 in. The time interval from the application to the termination of pressure was approximately 20 sec. Some of the compacts were annealed before testing. The results are listed in Figs. 4 to 8, inclusive. [ ] In Fig. 4 the curves of pressed density vs. compacting pressure, and sintered density versus compacting pressure show the typical direct relationship of pressure and density. Compacting pressures exceeding about 30 tons per sq. in. result frequently in expansion during sintering for the type of powder used. Fig 5. indicates that variations in the initial pressed density within the range of about 5 to 6 grams per c. c., affect only slightly the pressure required to obtain a

Jan 1, 1945

By Shigeki Nishimura

INTRODUCTION In this gapes, the author will describes to development of Yubari New coal mine. The construction set about since October 1970, and commenced from June 1975 in winning. Especially, descrives to compare with the studies at planning stage, and the experiences at under construction. The problems for development are next four: 1) There were no outcrop of the coal bearing strata, but the development was instituted against the deep coal seam occurrence at 800 m below the surface. 2) In order to the coal seams occured the deep level from the surface, threr had very difficult problems, i.e. temperature, earth pressure, methane etc. The countermeasure to solved them, were foundation of the development. 3) The construction was afflict with the inundation in high pressure, due to cement grouting and excavating alternately, overcame the difficulties. 4) The construction was finished by the encourage of national investment, in spite of the enterprise was weaken constitution from the energy revolution since 1960's. OUT LINE OF YUBARI NEW COAL MINE Geography Situation. Ishikari coal field is situated the west side of the Hidaka mountains, where runs north to south at center of Hokkaido, northern district of Japan. It's width is 40km in east and west, and length is 110km in north and south.

Jan 1, 1976

By PHILIP N. MOORE

THE development of the power of the Tennessee River at Muscle Shoals has become a matter of political interest as well as engineering possibility. The controversy over it has been so active that the facts have been obscured, the possibilities exaggerated. Although the members of the American Institute of Mining & Metallurgical Engineers are not generally specialists in hydroelectric development, those who visited Muscle Shoals in October, following the Birmingham meeting of the Institute, were interested, and many of them surprised to learn the actual conditions. These have long been familiar to those who have studied the matter through the reports of the U. S. Engineers on the subject. The approved plan contemplates three dams-No. 1, a low dam close to the City of Florence, planned in the interests of navigation, since the construction of the other dams has rendered impossible the use of the river without it. No. 2-named the Wilson Dam is now under construction. Concerning it political argumentation has waged. No. 3 Dam-much smaller, is planned to be erected several miles above No. 2.

Jan 1, 1925

For the year ending February, 1920 PRESIDENT HORACE V. WINCHELL MINNEAPOLIS, MINN. PAST PRESIDENTS PHILIP N. MOORE ST. Louis, Mo. SIDNEY J. JENNINGS NEW YORK, N. Y. FIRST VICE-PRESIDENT A. R. LEDOUX, NEW YORK, N. Y. TREASURER GEORGE D. BARRON NEW YORK, N. Y SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y

Jan 7, 1919

By C. C. Harris

The 3-parameter equation* was introduced1 as having the necessary form and flexibility for describing the major features of size distribution curves. Also, Eq. 1 was shown to contain most of the widely used 2-parameter equations as special cases. Special methods are necessary in order to determine the parameters of 3-parameter equations by graphical means. The procedure given previously required double graphical interpolation followed by regraphing the interpolated data. The theoretical basis of the method was a difference equation eliminating y. Several other methods for obtaining the parameters have been under development and one method appears to overcome the disadvantages of the earlier method and satisfies several procedural requirements. The points in favor of the new method as compared to the earlier method are as follows: 1. Estimation of the quality of fit is direct, and is in fact an essential part of the procedure. 2. The data is plotted directly without the necessity of interpolation from a graph. 3. The method makes use of Rosin-Rammler2 paper which because of expanded scaling in the coarse sizes leads to improved accuracy1 as compared with the log-log plot for the Gates3-Gaudin4-Schubann5 representation. 4. There is a gain over the earlier method in overall accuracy and in simplicity.

Jan 1, 1970

By Albert Sauveur

(Cleveland Meeting, October, 1912.) ALTHOUGH many metallurgists know that some pearlitic special steels can be made troostitic, martensitic, and even austenitic, without quenching, and, therefore, without exposing them to the dangers of the quenching-bath, the practical significance of such possibility does not seem to have received the attention it deserves. Let us recall briefly the mechanism of the transformation alluded to. In Fig. 1 (after Guillet) is shown the constitutional diagram of nickel-steel that; is, of alloys of iron, carbon, and nickel. Any steel the composition of which falls within the area LPO is pearlitic after slow cooling; any steel the composition of which is represented by a point within the area MLO is martensitic, and any steel within the area MNO is austenitic. Starting with pearlitic steel, then by increasing the carbon-content or the nickel-content, or both, the metal becomes martensitic and eventually austenitic; that is, its composition crosses first the boundary-line LO and then the line M0-and it remains martensitic or austenitic after slow (air) cooling.1 We have inn this way imparted to the metal without quenching it the properties of hardened carbon-steel. In other words, the steel is now self-hardening. Nickel cannot be introduced into solid steel, but by the well-known process of case-hardening it * Professor of Metallurgy and Metalllography in Harvard University. + Assistant in Metallurgy and Metallography in Harvard University. 1 The boundaries between the various zones are not, as a matter of fact, as sharp as indicated in the diagram, because pearlite is not transformed abruptly and in its entirety into martensite when a certain critical composition is attained, nor is martensite suddenly and completely converted into austenite. Greater refinement in the construction of the diagram would undoubtedly result in the introduction of troosto-pearlitic, troostitic, and troosto-martensitic zones between the pearlitic and martensitic areas and-of a martenso-austenitic zone between the martensitic and austenitic areas. Fur the purpose of this note, however, the existence of these transition-conditions may be ignored.

Nov 1, 1912

By V. Steve Reed, Ed L. Reed

The in situ leach mining process generates a waste stream that is high in sulfates, total dissolved solids, and radium 226. During the mining phase, the volume of the waste stream is relatively low and consists primarily of the bleed stream. During the restoration phase, larger volumes of waste water are generated. These waste streams require environrnentally sound disposal. The low net evaporation rate in the Coastal Bend area precludes pond evaporation as a feasible disposal alternative. Reverse osmosis is a practical method of reducing the volume of the waste water handled, but the concentrated waste stream from the reverse osmosis unit must be disposed properly. Deep well injection into highly saline reservoirs is considered a sound method of disposing of the liquid waste generated by in situ mining in the Gulf Coast uranium district. Thirteen injection wells have been permitted to serve the disposal needs of the leach mining industry in Texas. Of these 13, 11 have actually been drilled. Seven applications are pending. The injection zones for the permitted wells range from depths of 3050 to 6200 feet. Pressure limitations imposed on these wells range from 500 psi to 1350 psi. The following criteria are used to determine the desirability of a disposal well site: 1. A minimal number of nearby, improperly plugged borings which penetrate the disposal zone; 2. Minimal crustal disturbance; 3. Sufficient salinity of the water contained in the disposal zone; 4. Protection of oil and gas producing zones; and 5. Sand of sufficient permeability and areal extent to handle the desired volume without fracturing the reservoir. 1. Improperly plugged borings: During the early part of the century, oil wells, gas wells and test holes were drilled using cable tool equipment, often with a minimum amount of surface casing. Production casing, when it was set, was often partly removed when the holes were abandoned. Thus, wells drilled prior to 1940 frequently have less than 100 feet of surface casing and either no production casing or the upper part of the production casing removed. Additionally, these holes are often plugged only with mud. The close proximity of these holes to an injection well location are a concern in that they can provide an avenue for injection-depth fluids to migrate up the bore hole and jeopardize shallower fresh water reservoirs. Usually, where there are more than 6 or 8 poorly plugged borings in a 2 1/2 mile radius of the well site, it is preferable to examine deeper zones for disposal well potential. The deeper zones are especially attractive where the borings are not in a cluster, which renders monitoring more difficult. Often, even the deeper disposal zones are penetrated by a few improperly plugged borings. When this condition arises, the potential for leakage through the borings can be addressed in the following ways. a. Demonstration that the static head in the boring is higher than the anticipated increase in bottom hole pressure generated at the boring by the disposal well. A 100 psi differential between these two pressures is recommended. The calculated increased pressure at a boring caused by injection should be refined using annual bottom hole pressure measurements in the disposal well. Figure 1 illustrates an injection pressure map which can be overlain on the oil well map to determine the anticipated increase in pressure expected at each oil, gas or abandoned hole. b. Shallow ground water monitoring. A shallow monitor well is drilled next to the boring and both pressure and quality measurements are made periodically in the shallow well. c. Disposal zone monitoring. Recently there has been a tendency for regulators to require disposal depth monitor wells instead of shallow well monitoring. We consider disposal depth monitoring to be a less effective method of monitoring because it provides only indirect evidence of potential problems. Assumptions have to be made for the unplugged borings, such as mud weight, that are not addressed by the disposal zone monitoring program. There is little improvement with this system to that discussed in "a" above. A shallow zone monitoring program, however, yields direct evidence of a developing problem with an unplugged boring. Leakage by the boring will be detected quickly by an abnormal increase in pressure in the shallow well. Quality monitoring will detect upward migration of poor quality fluids. The pressure data provide an early warning of impending leakage; the quality monitoring will detect actual fluid migration.

Jan 1, 1980

Contents A - Metal Mining B - Minerals Beneficiation F - Coal H - Industrial Minerals I - Mining Geology L - Geophysics

Jan 11, 1953

By W. B. Dancy, A. Adams

Laboratory test work on heavy liquid separation of sylvite from halite is reported. Numerous tests were run on sylvite ore sized in the ranges of 4x20 mesh, 10x65 mesh, 8x100 mesh, -8 mesh and -10 mesh with heavy liquids in the range of 2.05 to 2.15 sp gr. From the test results, it was concluded that, with the type of ore under study and a size in the range of -8 mesh, a recovery as high as 90% could be achieved with a product grade of 70% KCl. However, a final product at an acceptable recovery cannot be made with one pass, and the float must either be further processed with heavy liquids or dried and sent to a conventional froth flotation circuit. Potash ores occurring in this country consist essentially of sylvite and halite plus minor amounts of magnesium sulfate salts and montmoril-lonite-type clays. Recovery of potash minerals from evaporite ores in the North American potash fields is accomplished almost exclusively by use of amine flotation. European practice involves froth flotation as well as solution-crystallization processes. Laboratory and pilot plant test work has been reported in Europe and the U. S. on the application of heavy media separation to potash ore beneficiation. Work was probably discontinued because of lack of ore with the required very coarse liberation characteristics (1/8 to 1/2 in. liberation size). Sylvite, with a gravity of 1.99, and halite, with a gravity of 2.17, appear to be ideal for separation by heavy liquids, which are now available in gravities from 1.59 to 2.95. This paper reviews preliminary results obtained from laboratory test work on heavy liquid separation of sylvite from halite. TEST WORK The heavy liquids used in the tests under discussion were chlorobromethane, with a specific gravity of 1.923, and dibromethane, with a gravity of 2.490. These liquids, completely miscible, were combined in the proportions needed to give a mixture having the desired specific gravity. Feed for the laboratory tests was mine-run ore screened to the desired mesh sizes. In conducting the tests, the sample was fed at a constant rate into a stream of heavy liquid and the mixture directed into a small separatory vessel. The float overflowed into a collecting pan while the sink collected in the bottom of the separatory vessel and was removed at the end of the test. Approximately 500 g of feed constituted a charge. Pulp density of the feed was kept low to prevent particle to particle interference in separation. With feed in the range of 8x100 mesh, a pulp density of under 10% solids by weight was found advisable. With coarser feed the pulp density could be carried as high as 15% solids. Time of separation was very rapid. In the case of 4x20-mesh material, separation was effected in 15 to 30 sec; with -10-mesh feed, separation required about 1 to 2 min. SPECIAL EQUIPMENT Since heavy liquids are toxic to varying degrees, all separatory work was carried out in a standard laboratory fume hood. It was noted that complete removal of fumes was not being effected; therefore the hood construction was modified, resulting in a completely satisfactory arrangement for heavy liquid test work. In the interest of safety, details of this fume hood are reported here. Unlike most fumes, heavy liquid fumes tend to settle and flow like water, rather than to rise like a gas. Working on this assumption, a standard water drain was installed in the hood. Across the front of the hood a 1-in. barrier was constructed. In the rear of the hood a false back was installed, with an adjustable sliding door on both the bottom and top of this panel. As shown in Fig. 1, the exhaust fan pulled a vacuum behind the barrier, sucking the heavy fumes from the bottom of the hood. Another addition was the drying box, shown to the right of the hood. This is simply a box covered on top with hardware cloth and connected by a 6-in. inlet to the hood. Sample trays made of fine mesh wire filter screens were found ideal for drying samples. With this arrangement, air flowed completely through the sample and all fumes were drawn into the hood. In use, it was found effective to cover with a

Jan 1, 1963

By W. R. Clark, W. W. Cotter

Jan 1, 1946

By W. W. Cotter, W. R. Clark

Jan 1, 1946

By D. F. Kelsall

The hydraulic cyclone, in simple or modified form, is finding increasing application in metallurgical processing. In this article, the author considers several aspects of conventional applications, less conventional applications and some potential uses of modified cyclones. Information concerning the mechanism of separation within a cyclone and the effect of the major variables is summarized. During the past twenty years, and especially in the last decade, hydraulic cyclones have found increasing application in metallurgical processing as classifiers and, under special circumstances, as thickeners. To a more limited extent cyclones have been used to extend heavy, or dense, medium separation into the finer size ranges, and several attempts have been made to separate dispersions of immiscible liquids with a view to use in the field of liquid-liquid extraction. A large proportion of published work reports incomplete data, applicable only to particular systems. The more useful papers, covering data of relatively wide significance, have been reviewed recently in considerable detail1,2 and no attempt will be made to cover the same material in the present paper. However, before considering several aspects of conventional application, less conventional applications and some potential uses of modified cyclones, it is considered pertinent to summarize information relating to the mechanism of separation within a cyclone and the effect of the major variables. LIQUID FLOW PATTERNS At any point within a simple cyclone the liquid velocity may be resolved into three components, i.e., the tangential or swirling velocity (v), the vertical velocity (w), and the radial velocity (u). The relative values of these components at selected positions within a typical cyclone have been established for water. 3 The extent to which similar flow patterns exist in systems of considerably higher viscosity, or apparent viscosity, operating under conditions of reasonable pressure drop, is not known with precision, but indirect evidence indicates that up to approximately five centipoise there is no marked change. Beneath the bottom of the vortex finder, envelopes of constant tangential velocity are cylinders coaxial with the cyclone, and, at any horizontal level, starting from near the conical wall, this component of velocity increases with decrease in radius (r) according to the relationship vrn = constant (where 0 < n < 1) This holds to regions near the center of the cyclone where v reaches a maximum value at a radius somewhat smaller than that of the inside wall of the vortex finder. At this point, the centrifugal acceleration, v2/r reaches a maximum value. As the radius is further decreased the tangential velocity decreases so that v = r. Above the bottom of the vortex finder there is a tendency for the first relationship to persist to near the outside wall of the vortex finder, until v reaches a maximum and then decreases rapidly as the wall is approached. The two most significant features of the vertical velocity distribution are an approximately conical Table I. List of Symbols v = liquid tangential velocity at any point in the cyclone w = liquid vertical velocity at any point in the cyclone u = liquid radial velocity at any point in the cyclone r = radius from cyclone axis to any point ? = half angle of conical portion of the cyclone ?= fluid viscosity d = particle diameter s = liquid specific gravity p = particle specific gravity d50 = the particle diameter which distributes 5090 to overflow, 50% to underflow e = overflow diameter, in. b = feed diameter, in. G = gpm of feed slurry

Jan 1, 1963

By G. W. Neighbor, M. S. Abrahams

The actice slip plane in InSb is found to be of the {111} type by using the method of two-tmce anulysis. Measurements of the rotation of the tensile axis with increasing plastic shear strain indicate that the tnacroscopic slip direction is a <110>. Recrystal-lization is first observed at a sheav strain of about 70 pct for a crystal deformed at a temperatzcre of 473° C and at a shear strain rate of 2.90 times 10- %ecc-I; the dislocation density corresponding to this value of the strain is 1 x 108 em-&apos;. At a shear strain of about 170 pct, the recrystallization process is complete. This appears to be the fimt time re-crystallization has heen observed in a semiconductor. V HE operation of the {Hi} glide plane in Ge was first noted by Gallagher.&apos; This finding was confirmed by Treuting who also extended the result to Si. Using X-ray techniques, Treuting3 demonstrated that the macroscopic slip direction in Ge was of the <110> type. The choice of the (111) <110> slip system in Ge is exected since in the diamond-type structure the {Ill7 plane is the plane of highest density and the <110> direction is the direction of closest packing.4 There is little reason to expect that the glide elements of InSb are different from those of Ge, since the zinc-blende structure characteristic of InSb is quite similar to the structure of Ge. With regard to InSb, Allen5 has indicated that the glide plane is the {111} type. There appears to be no quantitative determination of the glide direction, however. The present work was undertaken to establish both the glide plane and glide direction in InSb and also to see if recrystallization occurs at large shear strains. EXPERIMENTAL PROCEDURE Mechanical Deformation. The single crystals of InSb used in this investigation were deformed in uni-axial tension. The tensile axis of the specimens was [145] and the periphery was bounded by (111) and (321) planes as shown in Fig. 1. The metallographi-cally polished specimens were deformed in a dynamic atmosphere of He, using an Instron machine. The tensile tests were performed at temperatures in the range of 300°C to the melting point (525OC) and at shear strain-rates varying between 1.94 X 104 sec-&apos; to 1.94 x 103 sec-&apos;. Additional details concerning the preparation and deformation of the specimens have been presented previously.&apos; Analysis of the Glide Elements. The traces of the active slip plane in both (111) and (321) planes were analyzed according to the usual method of two-trace analysis." The macroscopic slip direction was determined by measuring the rotation of the tensile axis as a function of plastic strain,8 These measurements were made from Laue back-reflection X-ray photographs. The X-ray beam was perpendicular to the (111) plane. A given crystal was used for only one measurement of the rotation of the tensile axis after it had been strained to a predetermined value. Therefore, care was taken at all times to insure that the X-ray beam was parallel to the [Ill ] direction of all the samples. RESULTS AND DISCUSSION Glide Plane. After 3.4 pct plastic shear-strain, at a temperature of 369°C and a shear strain-rate of 1.94 x 104 sec-&apos;, the slip traces on the (111) and (3.21) planes appear as in Figs. 2(a) and 2(b), respectively. The results of an analysis of these glide markings demonstrate that the slip plane is (111). The operation of this plane is expected on the basis of the orientation of the specimen, since glide on this plane and in the [I011 direction will result in

Jan 1, 1962

By K. A. Natarajan, S. C. Riemer, I. Iwasaki

The relative significance of corrosive and erosive wear in magnetic taconite grinding is examined. The influence of different types of aeration (nitrogen, air, and oxygen) on ball wear was established for mild steel and high carbon low alloy steel balls. Ball wear data from dry and wet grinding tests are compared with those obtained in the presence of an organic solvent that does not promote electrochemical corrosion. Marked ball grinding tests and electrochemical measurements involving ball material and magnetite electrodes indicate that contribution from oxygen toward wear (corrosive wear) is relatively small, and abrasive wear appears to be significant. Rheological properties of the slurry appear to have an important bearing on the abrasive wear of grinding balls.

Jan 1, 1985

By H. T. Bowman

For more than 80 years the Bessemer process has depended upon the ability, skill, and judgment of the blower, although as early as the I860&apos;s it was recognized that the process would benefit by some type of instrumental contro1.l IIowever, instruments with sufficient recording speeds did not exist, so the end-point determination was always dependent upon the blower&apos;s eye. This placed an obstacle in the way of precise experimental work, because of the absence of the necessary records and reference points as reported by Work.2 The use of the photocell provided the instantaneous record of the blow that made this experimental work possible and provided more scientific control for the process as discussed by Graham,3 A brief description of the progress of the blow will illustrate the recording function of the instrument. The silicon in the iron is being oxidized during the first minutes of the blow, as pointed out by Henning4 in a table showing the order of metalloid elimination. The product of this oxidation is a solid that remains in the converter, so there is virtually no flame during this part of the blow. This low flame luminosity is illustrated by the flame recording shown in Fig. I, where the silicon blow is plainly marked. The dull flame of the silicon blow gradually gives way to the brilliant carbon flame as the increasing quantities of carbon monoxide formed inside the converter burn to dioxide upon contact with the atmosphere above the vessel. When the carbon reaches some low value under 0.20 per cent, there is insufficient menoxide formed to maintain the dioxide flame, so its intensity drops. Throughout the flame drop carbon continues to burn, until at some value around 0.05 per cent an arrest occurs in the recorded drop. This point has been designated as the end point. The period of time from this end point until the vessel is turned upon its side and blowing has stopped has been called the afterblow. This afterblow is used as a measure of the degree of metal oxidation, and uniformity demands that it be controlled within narrow limits. Iron and blowing conditions are likely to change several times during a turn, necessitating corresponding changes in end-point control. It is the purpose of this paper to discuss these changes, the factors that make them necessary, and their bearing upon the quality of steel. Carbon-FeO Relationship In the Bessemer process oxidation relationships are precise. Fig. 2 shows a graph of the carbon-FeO relationship. The familiar "bomb-test" method, described by Mccutcheon and Rautio,5 was used for obtaining these and all other dissolved FeO values herein reported, all tests being taken from the converter before deoxidation unless otherwise noted. All tests of 0.10 per. cent carbon and above were obtained from metal blown for duplexing. McGinley and Woodworth6 reported iron oxide values for blown metal, but their tests were obtained by a . different method than were those

Jan 1, 1942

By H. T. Bowman

For more than 80 years the Bessemer process has depended upon the ability, skill, and judgment of the blower, although as early as the I860&apos;s it was recognized that the process would benefit by some type of instrumental contro1.l IIowever, instruments with sufficient recording speeds did not exist, so the end-point determination was always dependent upon the blower&apos;s eye. This placed an obstacle in the way of precise experimental work, because of the absence of the necessary records and reference points as reported by Work.2 The use of the photocell provided the instantaneous record of the blow that made this experimental work possible and provided more scientific control for the process as discussed by Graham,3 A brief description of the progress of the blow will illustrate the recording function of the instrument. The silicon in the iron is being oxidized during the first minutes of the blow, as pointed out by Henning4 in a table showing the order of metalloid elimination. The product of this oxidation is a solid that remains in the converter, so there is virtually no flame during this part of the blow. This low flame luminosity is illustrated by the flame recording shown in Fig. I, where the silicon blow is plainly marked. The dull flame of the silicon blow gradually gives way to the brilliant carbon flame as the increasing quantities of carbon monoxide formed inside the converter burn to dioxide upon contact with the atmosphere above the vessel. When the carbon reaches some low value under 0.20 per cent, there is insufficient menoxide formed to maintain the dioxide flame, so its intensity drops. Throughout the flame drop carbon continues to burn, until at some value around 0.05 per cent an arrest occurs in the recorded drop. This point has been designated as the end point. The period of time from this end point until the vessel is turned upon its side and blowing has stopped has been called the afterblow. This afterblow is used as a measure of the degree of metal oxidation, and uniformity demands that it be controlled within narrow limits. Iron and blowing conditions are likely to change several times during a turn, necessitating corresponding changes in end-point control. It is the purpose of this paper to discuss these changes, the factors that make them necessary, and their bearing upon the quality of steel. Carbon-FeO Relationship In the Bessemer process oxidation relationships are precise. Fig. 2 shows a graph of the carbon-FeO relationship. The familiar "bomb-test" method, described by Mccutcheon and Rautio,5 was used for obtaining these and all other dissolved FeO values herein reported, all tests being taken from the converter before deoxidation unless otherwise noted. All tests of 0.10 per. cent carbon and above were obtained from metal blown for duplexing. McGinley and Woodworth6 reported iron oxide values for blown metal, but their tests were obtained by a . different method than were those

Jan 1, 1942

By A. L. Foell

THE development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. FURNACE LINES About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied between 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: [Hearth diameter 25 ft. o in. Height of bosh 10 ft. o in. Bosh angle 8 1 ½° Diameter top of bosh 28 ft. o in. Inwall batter per foot 15/16 Stock-line diameter 19 ft. 6 in. Large-bell diameter 14 ft. 6 in. Height from iron notch to top ring casting 100 ft. o in.] In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace for the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime, the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1942

By T. Sterry Hunt

WET processes for the extraction of copper from its ores have of late attracted much attention, especially in Europe, where the use of oupriferous iron-pyrites as a&apos; source of sulphur prevails. These processes present an additional interest, when, as is often the case, the copper-ore&apos;s to be treated contain one or both of the precious metals, since the complete separation of these from copper, either in the dry or the moist way, is, as is well known, one of the difficult problems of metallurgy. The principal wet processes hitherto in use for the extraction of copper from its ores, may be included under three classes : I. Those in which the copper in snlphuretted ores is rendered soluble in water by calcining them, after a preliminary roasting which removes the greater part of their sulphur, with a portion of common salt, by which the copper is converted into a chloride (Long-maid and Henderson), or with sulphate of soda, by which sulphate of copper is formed (Monnier). Allied to these is the method by which a portion of the copper is got as soluble sulphate by roasting without addition, a process which is sometimes modified and rendered more complete by re-roasting the lixiviated residues with the addition of a portion of raw sulphuretted ore (Bankart). II. Those methods in which free chlorhydric or sulphuric acid is used to dissolve the copper- from oxidized or roasted ores. These, while simple and efficient, are too costly, except in certain localities where chlorhydric acid is a waste product. Related to them is the plan which consists in exposing the oxidized and moistened ores to the slow action of sulphurous acid mixed with air, by which a soluble sulphate of copper is formed. It has been proposed to decompose the solutions of sulphate or chloride of copper by sulphuretted hydrogen, thus separating the copper as sulphide, and using the liberated acid to dissolve fresh portions of oxidized copper. It is, however, the almost universal practice to throw down the copper from its solutions, however obtained, in the metallic state by the use of iron, either scrap-iron or iron-sponge; although in some instances

Jan 1, 1882

By Eric R. Jette, Earl S. Greiner

Although the mechanical and chemical characteristics of certain iron-nickel-silicon alloys have been investigated,1 the available literature shows no results of a systematic investigation of the constitution of this system. &apos;This paper describes the results of an X-ray investigation of the constitution of the iron-rich iron-nickel-silicon alloys at 600°C. Data 011 the constitution of the included binary systems obtained in other investigations have been correlated with the structure of the ternary alloys. Jette and Foote2 have presented a tentative constitutional diagram of the iron-nickel system. following X-ray studies on quenched specimens. This diagram shows that the alloys at 600°C. containing from zero to approximately 4 atomic per cent nickel consist of a body-centered cubic (alpha) phase, the alloys containing 4 to 24 atomic per cent nickel consist of body-centered cubic (alpha) and face-centered cubic (gamma) phases, and the alloys containing from 24 to Ioo atomic per cent nickel consist of a face-centered cubic (gamma) phase. These investigators recognized that it was not possible to retain the gamma phase in equilibrium by quenching alloys containing less than approximately 25 atomic per cent nickel and that high-temperature X-ray methods were desirable to determine the gamma-phase solubility limit. In a later investigation of the iron-nickel alloys, Owen and Sulley3 determined the alpha-phase solid solubility limit to be 3.5 atomic per cent nickel at 600°C. High-temperature X-ray methods showed the solid solubility limit of the gamma phase to be 14 atomic per cent nickel at 600°C. Since the high-temperature X-ray method should reveal equilibrium conditions in these alloys better than the quench method of other investigators, the results of Owen and Sulley pertaining to the gamma-phase boundary are to be preferred. As the result of an X-ray investigation of quenched iron-silicon alloys, Greiner and Jette4 have shown these materials to consist of a body-centered cubic (alpha) phase containing from o to 26.4 atomic per cent silicon at 600°C. The alloys containing from 26.4 to approximately 50 atomic per cent silicon consist of two phases at 600°C.; namely, alpha and eta. The eta phase corresponds to the stoichiometrical formula FeSi (33.4 wt per cent Si)." The literature pertaining to the constitution of the nickel-silicon alloys has been reviewed by Ackerman,&apos; who found disagreements in the results of various investigators on several parts of the system. Subsequent data on the constitution of the nickel-silicon alloys were reported by oSawa and okamoto.6

Jan 1, 1943

By Earl S. Greiner, Eric R. Jette

Although the mechanical and chemical characteristics of certain iron-nickel-silicon alloys have been investigated,1 the available literature shows no results of a systematic investigation of the constitution of this system. &apos;This paper describes the results of an X-ray investigation of the constitution of the iron-rich iron-nickel-silicon alloys at 600°C. Data 011 the constitution of the included binary systems obtained in other investigations have been correlated with the structure of the ternary alloys. Jette and Foote2 have presented a tentative constitutional diagram of the iron-nickel system. following X-ray studies on quenched specimens. This diagram shows that the alloys at 600°C. containing from zero to approximately 4 atomic per cent nickel consist of a body-centered cubic (alpha) phase, the alloys containing 4 to 24 atomic per cent nickel consist of body-centered cubic (alpha) and face-centered cubic (gamma) phases, and the alloys containing from 24 to Ioo atomic per cent nickel consist of a face-centered cubic (gamma) phase. These investigators recognized that it was not possible to retain the gamma phase in equilibrium by quenching alloys containing less than approximately 25 atomic per cent nickel and that high-temperature X-ray methods were desirable to determine the gamma-phase solubility limit. In a later investigation of the iron-nickel alloys, Owen and Sulley3 determined the alpha-phase solid solubility limit to be 3.5 atomic per cent nickel at 600°C. High-temperature X-ray methods showed the solid solubility limit of the gamma phase to be 14 atomic per cent nickel at 600°C. Since the high-temperature X-ray method should reveal equilibrium conditions in these alloys better than the quench method of other investigators, the results of Owen and Sulley pertaining to the gamma-phase boundary are to be preferred. As the result of an X-ray investigation of quenched iron-silicon alloys, Greiner and Jette4 have shown these materials to consist of a body-centered cubic (alpha) phase containing from o to 26.4 atomic per cent silicon at 600°C. The alloys containing from 26.4 to approximately 50 atomic per cent silicon consist of two phases at 600°C.; namely, alpha and eta. The eta phase corresponds to the stoichiometrical formula FeSi (33.4 wt per cent Si)." The literature pertaining to the constitution of the nickel-silicon alloys has been reviewed by Ackerman,&apos; who found disagreements in the results of various investigators on several parts of the system. Subsequent data on the constitution of the nickel-silicon alloys were reported by oSawa and okamoto.6

Jan 1, 1943