Search Documents

By F. R. Zachar

IT has always been understood, in northern West Virginia where both the Pittsburgh and Sewickley seams are mined, that pillaring or splitting in the lower Pittsburgh seam could break the interval strata and make mining in the overlying Sewickley difficult or impossible. In some instances, however, mining methods practiced in the overlying Sewickley have reversed the problem, resulting in a shifting of the intermediate layer and destroying valuable acreages of the Pittsburgh seam below. The Pittsburgh seam in this area is, on the average, 102 in. thick. About 18 in. of low-quality head coal are left for roof protection as it is mined. Immediately over the coal are two draw slates, two rider 'seams, and a good hard black shale, locally called black rock, which serves as a permanent roof where draw slates and riders are taken down on certain main haulroads. In most areas mined in this seam in the past the bottom has been satisfactory but soft. However, in areas now being mined by the Christopher Coal Co. in Monongalia County the bottom is very hard and unyielding. The Sewickley seam, lying 85 ft above the Pittsburgh, will average nearly 70 in. in thickness and is overlain by massive shales and sandstones. Much of the seam is mined only down to the "sheep skin," a hard band about 4 in. above the bottom, which is composed of relatively hard shale. Fig. 1 shows a typical cross-section through the Pittsburgh and Sewickley seams in the area being discussed. The thin Redstone seam is not deep-mined but is stripped in some locations where it outcrops. Most of the Sewickley seam in the Morgantown areas has been mined out from 10 to 30 years. There are at present only two large mines and five or six others of small production operating in that seam. Mining systems in the past were generally of the room and pillar type with some full pillar extraction. This seam in the Scott's Run area was operated by as many as thirty or forty different companies at one time, during an era beset with strikes, market failures, and depressions. Most of the barrier pillars along the many main haulroads were abandoned, and blocks of Sewickley coal that would be fully recovered with today's machinery were left unmined when conditions became anything less than favorable. Consequently the mined-out Sewickley is spotted throughout with solid blocks varying in size from 100x100 ft to 200x400 ft and larger. It is these unmined Sewickley blocks surrounded by worked-out portions that have caused transmissions of roof stresses to underlying Pittsburgh mining areas, see Fig. 2, resulting in untold difficulty. As the Christopher Coal Co. operates both the Pittsburgh and Sewickley seams, accurate maps of workings in both seams are readily available and are regularly consulted. The first Pittsburgh squeeze attributed to overlying Sewickley blocks occurred in the Arkwright mine, where a shuttle car crew was developing a section consisting of seven panel headings. These entries were being driven in solid coal 3400 ft from the nearest worked-out Pittsburgh area. As mining advanced it was noticed that certain ribs began to slough and certain areas to show signs

Jan 1, 1952

By H. B. Muller

Single stage autogenous grinding of run-of-mine ore was selected by Broken Hill South Ltd., parent Company of Cobar Mines Pty. Ltd. for the concentrator to treat 60,000 tons per four weekly period of copper and complex copper-lead-zinc sulphide ores from the C.S.A. Mine at Cobar, Australia. Ore is mined by mechanised horizontal cut-and-fill stoping and is prepared for grinding by crushing under- ground in a 60 in. x 48 in. jaw-crusher set at 5 in. closed side setting. The ore is reduced to 80% minus 76 microns in two parallel sections each of one 22 ft. dim. x 7 ft. long autogenous grinding mill, powered by a 1,250 H.P. motor, operating in closed circuit with a single stage 20 in. dim. cyclone. Broken Hill South's original concept of the concentrator required the maximum use of reliable instrumentation, centralised control, and the minimum of manning. To achieve this objective the control room, housing the process recorders, alarms, closed circuit television monitors and all the control equipment, overlooks the grinding and flotation sections, and the whole plant is serviced by a public address system. The grinding units and associated equipment are located in the open and are serviced with the aid of a mobile crane and a mobile hydraulically-operated liner lifting device.

Jan 1, 1970

By Paul C. Merritt

Samuel Hopkins, an 18th century inventor from Philadelphia, has been little noted nor long remembered by History, but it was he who on July 31, 1790, obtained what no other man can ever achieve -the first patent issued by the Government of the United States. Signed by President George Washington, the patent guaranteed to Hopkins the protection of the American Government for his "improvement, not known or used before, . . . in the making of Potash . . . by a new Apparatus and Process." The patent itself is no longer important, but it serves as a milestone in the development of an industry that is now rapidly moving to fulfill its role as a mineral to feed the world. Potash ranks as one of the oldest products of Man, having been used as a condiment by the habitants of Gaul a thousand years before Athens achieved its Golden Age of culture. By Hopkins' time, the uses of potash had changed considerably, going primarily into glass-making, tanning, soap, and explosives, yet the same sources and techniques of manufacturing potash used during the earlier 2000 years-that is, leaching of plant ashes in iron pots with water, followed by water evaporation and crystallization of the potassium salts-were still being used.

Jan 10, 1966

By W. F. Dietrich

Mineral fillers are relatively inert chemically under the conditions of use but have physical properties* that modify those of the materials • The properties. uses, and other data on 15 classes of important *The pro listed in the second edition of Industrial Minerals and Rocks.l A third edition of this reference is in preparation. in which they are incorporated. The mineral fillers considered in this article are asbestos, barite, clays, diatomite, crushed limestone, limestone whiting and lime, mica, silica, talc and soapstone, and pyrophyllite. Slate and stone, other than limestone and its derivatives, are excluded because, even though used in large quantities, they are exceptionally low-cost materials generally produced close to the area where they are used. Carbon black is excluded because it is manufactured from natural gas and more than 90 pct of the output is used in rubber; hence the factors for estimating requirements are easily evaluated. OVERALL GROWTH FACTORS Table I gives the population, retail sales, and value added by manufactures in the U. S. and in the eleven western states in 1954. These data are rough guides to the proportionate part of total U. S. markets for products containing mineral fillers that may be expected in a given area. For example, the population of the eight Mountain states in 1954 was 3.6 pct, and retail sales in these states were 3.8 pct of the U. S. total, but the value added by manufactures was only 1.3 pct of the U. S. total. On the other hand, the three Pacific Coast states, with 10.3 pct of the total population, had 12.0 pct of the retail sales and produced 9.6 pct of the value added by manufactures. On an industry-by-industry basis the correlation between the three guideposts will not be as close as shown in the 1954 data for the Pacific Coast states, but in the long-term view the continuing rapid population growth in the western states is certain to result in expanded industrial production at an even more accelerated pace, which will shorten the gap between local consumption and production in most major groups of manufactured consumer goods. Of course, there will always remain favorable areas for production of specific products. Such special situations must be individually analyzed. Fig. 1 compares the population trends in the U. S., the western states, and California with Real Gross National Product from 1910 to 1957, with forecasts to 1970. It is estimated' that the U. S. Real Gross National Product, as measured by the value of goods and

Jan 1, 1960

By R. D. Rubright, Owen J. Hart

In the Bingham district over a span of more than 90 years, 43,947,104 tons of "non-porphyry" copper, lead, zinc, gold, and silver ore have been mined from a folded and faulted alternating series of Pennsylvanian and Permian limestones and sandstones and from some Tertiary intrusives. This ore came from six major mine areas located east, south, and west of the Bingham stock, site of Kennecott's porphyry copper deposit. The sediments were affected by varying degrees and types of metamorphism within 2000 feet or more of the Bingham stock. The intrusives consisting of the mineralized Bingham and the unmineralized Last Chance stocks and numerous dikes and sills of granite and monzonite were intruded into the asymmetrical northwest-trending and plunging Bingham syncline. Extrusives, although present, contain no ore. The bulk of the non-porphyry ore in the district was found above the Midas thrust. The primary ores are found in three major types of deposits: concordant bedding fissures, crosscutting fissures, and replacement deposits. These deposits consist of both copper and lead-zinc ore bodies that contain various amounts of gold and silver. These are in places roughly zoned both laterally and vertically and have been mined for up to 10,000 feet outward from the center of the Bingham stock and up to 5000 feet vertically below the surface. Secondary ore was of minor importance and was found in and under the oxidized zone at shallow depths. Genetically the Bingham stock, the ores, and related phenomena have had a common source.

Jan 1, 1968

By R. A. Haney, S. J. Gigliotti

Over the past ten years, analysis of the acceptability of face ventilation systems has been based on numerical criteria rather than solely a study of air flow and methane patterns in the face area. This type of analysis has become possible primarily because of the instrumentation and mathematical models developed by the Ventilation Division, Pittsburgh Health Technology Center, Mine Safety and Health Administration (MSHA). To properly use these mathematical models, large amounts of methane and airflow data must be collected in the face area during mining activities. To supplement underground testing of face ventilation systems, a full scale model of a face area was built. This model includes a full scale model continuous miner, a face ventilation system, a gas release system, and a remote methane detection system. The remote methane detection system consists of an array of twelve methane sensors located throughout the face area. Data from the sensors are transmitted to strip chart recorders. Methane, air quantity, and other data collected during a test are entered into a computer for analysis. This paper presents the data entry system, the models used for data analysis, the test results, and the application of these results to a face ventilation system.

Jan 1, 1983

By Arthur Forsyth

A SEARCH through the available literature shows that the cobalt-nickel-silicon system has not been systematically studied. This seems rather odd because all three elements are fairly abundant and have better than average corrosion resistance; however, they have high melting points, which makes experimental work difficult. Cobalt and nickel form a continuous series of solid solutions and each metal dissolves about 7.5 per cent silicon. Many ternary alloys have been studied and the results have been published in a great many different ways, but to present such data in a short but clear and understandable manner is still a problem. The following pages describe the results of the study of 76 alloys from which the partial ternary diagram (Fig. 1) of the cobalt-nickel-silicon system has been drawn. The alloys were chosen according to the plan in Fig. la by taking definite ratios of cobalt and nickel, such as 70 Ni, 30 Co or 40 Ni, 60 Co, and adding silicon in various percentages. Each section was studied in detail by means of thermal analysis and microscopic examination, but only two of these detailed sections were thought necessary in the point perspective drawing to give a comprehensive picture of the liquidus, solidus and solid transformations that take place over the temperature ranges studied. Complete thermal analyses and microscopic data are given in Table 1.

Jan 1, 1940

By Cyril Stanley Smith

Although alloys of copper and silicon were examined several years ago,' and their excellent mechanical properties were shown, it was not until C. B. Jacobs 2 introduced manganese in small quantities to the alloys that they became of commercial importance. A few years ago The American Brass Company took over the patents and commenced to manufacture the alloy under the name "Everdur." The present study of the constitution of the ternary system was undertaken in order to reach a fuller understanding of the behavior of the alloy. Review of Previous WORK on the BinaRy Systems There have been no papers published dealing with the constitution of the ternary system, although some tests of the mechanical properties have been described," which indicate that there is a change in solubility with temperature. Copper-silicon System The copper-silicon system has been studied in detail by the author and is described in two papers published in 1928.V he portion of the diagram up to 8 per cent. silicon, as determined by this research, is reproduced in Fig. 1. The author's previous papers include a complete review of the work of other investigators and it is not necessary to deal further with this system here. Copper-manganese System The copper-manganese system has been investigated by several workers, notably Lewis,5 Wologdine,6 Sahmen7 and Schemtschuschny,

Jan 1, 1930

By J. B. Dilworth

I. INTRODUCTION. THE purpose of this paper is, first, to give a general account of a little-known coal-district of SE. Kentucky, its topography, drainage, and mineral resources, for those who may be interested in its economic development; and secondly, so to describe the geologic features of the field as to furnish available data to those engaged on the broader problems of Appalachian coal-geology. The data from which the major portion of the paper has been prepared were obtained, in professional investigations for private individuals and corporations, within the last decade. The area under review, defined by a heavy line on the map, Fig. 1, lies between Little Black and Pine mountains, and extends from Harlan on the west to a N-S. line crossing Looney creek 3 miles from its mouth on the east. This area can be divided for description into a Western and an Eastern Division. The character of investigation pursued in the Western Division, below Fugitt creek, was very different from that employed in the Eastern. In the former, only a rapid reconnoissance was attempted : such coal-openings as had been made by prospectors or by citizens in obtaining fuel were visited, their sections measured and, in many instances, sampled. Elevations were obtained barometrically and approximate locations sketched on a small-scale map. In a field where the coals are so well opened, the reconnoissance method gives a very fair idea of the number and character of the principal beds and their relative positions, and affords much evidence for their correlation over wide areas, without permitting the more refined work required to discover all the seams of the measures and to determine the details of geologic structure.

Feb 1, 1912

By P. A. Laxen, H. R. Spedden, A. M. Gaudin

WHEN a mineral particle is fractured, bonds between the atoms are broken. The unsatisfied forces that appear at the newly formed surface1 are considered to be responsible for the adsorption of ions at the mineral surface. A knowledge of the mechanism and extent of ion sorption from solution onto a mineral surface is of interest in the development of the theory of flotation.2,3 Study of the adsorption of sodium from an aqueous solution on quartz offers a simple approach to this complicated problem. The availability of a radioisotope as a tracer element meant that accurate data could be obtained.4,5 Three main factors which appeared likely to affect the adsorption of sodium are: 1-concentration of sodium in the solution, 2-concentration of other cations in the solution, and 3-anions present in the solution. Hydrogen and hydroxyl ions are always present in an aqueous solution. By controlling the pH, the concentration of these two ions was kept constant. The variation in the amount of sodium adsorbed with variation in sodium concentration was then determined under conditions standardized in regard to hydrogen ion. The effect of concentration of hydrogen ions and of other cations was also measured. A few experiments were made to get a preliminary idea on the effect of anions. The active isotope of sodium was available as sodium nitrate. Standard sodium nitrate solutions were used throughout these experiments except when the effects of other anions were studied. It was found that sodium adsorption increased with sodium-ion concentration, but less rapidly than in proportion to it. Increasing hydrogen-ion concentration, or conversely decreasing hydroxylion, brings about a comparatively slight decrease in sodium-ion adsorption. Increasing the concentration of cations other than hydrogen or sodium decreases somewhat the adsorption of sodium ion. It would appear as if the kind of anion is a secondary factor in guiding the amount of sodium ion that is adsorbed. Materials and Methods Quartz The quartz was prepared as in previous work in the Robert H. Richards Mineral Engineering Laboratory4 except for the refinement of using de-ionized distilled water for the final washing of the sized quartz, prior to drying5 To minimize the laborious preparation of quartz, experiments were made to determine whether the sodium-covered quartz could be washed free of sodium and re-used. The experiments were successful as indicated by lack of Na' activity on the repurified material and by its characteristic sodium adsorption. Table I gives the spectrographic analyses of the quartz used. The quartz ranged from 16 to 40 microns in size, averaging about 23 microns (microscope measurement), and had a surface of 1850 sq cm per g (lot I), 2210 (lot II) and 2000 (lot III) as determined by the Bloecher method.6 Radioactive Sodium Method of Beta Counting for Adsorbed Sodium: Na22, the radioisotope of sodium, possesses convenient properties.7 It has a half-life of 3 years, thus requiring no allowance for decay during an experiment. On decay it emits a 0.575 mev ß radiation and a 1.30 mev ? radiation. The decay scheme is illustrated in the following equation: [Y Nam S. - 'Net 3 years] The ß radiation is sufficiently strong to penetrate an end-window type of Geiger-Mueller counting tube. This, in turn, makes it possible to use external counting, a great advantage in technique. Furthermore, it permits the assaying of solids arranged in infinite thickness, while assaying evaporated liquors on standardized planchets. The equipment used was standard and similar to that employed by Chang8 The original active material was 1 ml of solution containing 1 millicurie of Na22 as nitrate. This active solution was diluted to 1000 ml. Five milliliters of this diluted active solution was found to give a quartz sample a sufficiently high activity for accurate evaluation of the sodium partition in the adsorption measurements. Also, 1 ml of final solution gave a sufficiently high count for precision on the liquor analyses. The sodium concentration of the diluted active solution was 1.2 mg per liter, so that 6 mg of sodium for 60 ml of test solution and 12 g of quartz was the minimum amount used. The active solution was stored in a Saftepak bottle. Procedure for Adsorption Tests: The method consisted of agitating 12 g of quartz with 60 ml of solution of known sodium concentration for enough time to establish equilibrium between the solution and the quartz surface. The quartz was separated as completely as possible from the solution by filtering and centrifuging. The activity on the quartz and in the equilibrium solution was measured and the partition of the sodium was calculated from the resulting data. The detailed procedure for the adsorption test is set forth in a thesis by Laxen5 In brief, it included the following steps: 1-Ascertainment of linearity between concentration of Na22 and activity measured. 2-Evaluation of factor to translate activity on solid of infinite thickness in terms of activity on an evaporated active film of minute thickness, on the various shelves of the counter shield. 3-Taking precautions to avoid evaporation of water during centrifuging.

Jan 1, 1952

By William G. [Peryam], Bishop Ottey M., Fred E. Johnson

THE Lepanto Consolidated Mining Company is the largest copper producer in the Philippines, and the only one that makes a concentrate valuable principally for its copper; also, it has the only productive copper mine situated at considerable distance from the sea, and is the only one in the islands operating its own smelter. The Lepanto mine is in the Municipal District of Mankayan, sub-province of Benguet, near the heart of the Mountain Province of Northern Luzon. It is 165 km. from its shipping point at San Fernando, Province of La Union, on the shore of the China Sea. Elevations at the property range from 3200 to 4500 ft. The climate is very mild; temperatures are seldom below 50° or above 80°F. Annual rainfall approaches 170 in. and is mainly confined to a rainy season lasting from May to October. The months from December to April, inclusive, are usually extremely dry. This climatic pecularity entails the problems of landslides on the roads during the rainy season and water shortage during the dry season. The Mountain Trail, an improved rock-surfaced toll road maintained by the Commonwealth Government, gives access to the property. The 105 km. over this road may be traveled in about 4 ½ hr. during the dry season. Very few sections of the road are straight for more than 100 meters, and about one third of it is a one-way road controlled by gates. All freight for the property is delivered by the Manila Railroad Company to Bauang, La Union, 45 km. west of Baguio and at sea level, where it is picked up by freight trucks and hauled via Baguio to Lepanto. Granulated matte is hauled in bulk from Lepanto in four-ton lots on freight trucks to the storage bins at San Fernando. Freight rates from Bauang to the property amount to P8.00 per ton, and from the property to San Fernando the rate is P16.00 per ton. The company pays the road toll, P1.00 per truck, each way. THE CAMP The company maintains a modern camp, well separated from the mine and reduction plant. Comfortable and sanitary living quarters, water, and light, as well as free medical service are provided all employees. A hospital staffed by a doctor and two nurses takes care of all medical treatment. Considering recreational facilities of great importance, the company has provided two tennis courts, two basketball courts, and badminton courts for employees. Bowling alleys and a motion picture theater are operated by the company, the profits being expended for other recreational purposes. A moderate sized recreation hall serves for barrio dances, meetings,

Jan 1, 1942

By Frederick Rhines

IT has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick's law (equation 1 below), ? in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick's law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Jedele and of Jedele.§ These data are essentially for one temperature alone and do not furnish any information on the variation of the activa-tion heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a singles olid solution field. Much of the argument concerning the properties of metals that deter-mine D and Q has been drawn from data in which variations of the quan-tities with concentration are unknown, for these data- have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concen-trations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By Frank E. Hauser, Philip R. Landon, John E. Dorn

The flow and fracture strengths of polycrystalline aggregates of high purity magnesium and a solid solution of aluminum in magnesium were determined as functions of temperature and grain size. Magnesium was found to obey two distinct fracture laws. Over the high temperature range, the fracture stress decreased with increasing test temperatures in a manner that closely paralleled the flow stress-temperature relationship. However, over the low temperature range, the fracture stress was independent of the test temperature though highly dependent on grain size, following the trend that is typical for the low temperature brittle fracturing of polycrystalline aggregates of body-centered-cubic and close-packed-hexagonal metals. Even at 78°K, however, plastic strains of 1 to 7 pet were obtained preceding onset of brittle fracturing. Over the brittle fracture range of temperatures, the fracture stress increased linearly with the reciprocal of the square root of the mean grain diameter, while over the entire range of temperatures investigated, the flow strength was observed to increase linearly with the reciprocal of the square root of the mean grain diameter. PREVIOUS investigations', 'have shown that deformation of coarse grained aggregates of high purity magnesium is interrupted by fracturing at very small strains. Such tendency toward brittle fracturing increased with increasing grain size and decreasing test temperature. In several respects, however, low temperature fracturing of magnesium appeared to differ from the truly brittle type exhibited by zinc, molybdenum, tungsten, and iron, so often characterized as a cleavage mode of fracturing. The absence of a well-defined cleavage mechanism for fracturing and the fact that some plastic deformation precedes fracturing might suggest that magnesium does not exhibit the same kind of brittle fracturing that is common to body-centered-cubic metals and to other close-packed-hexagonal metals. But, as will be shown, the low temperature fracture laws for magnesium are analogous to those that apply to iron, molybdenum, tungsten, and zinc in spite of differences in mechanisms and in plastic strains to fracture. In view of these observations. the low temperature fracturing of magnesium will also be called brittle fracturing. This, of course, does not imply that the brittle fracturing of metals is synonymous with the brittle fracturing of glass or other nonmetallics. Whereas the brittle fracturing of glass probably obeys Griffith's law, the low temperature brittle fracturing of metals arises from stresses induced by a series of dislocations piled up at an opaque grain boundary. Experimental Results All tests were made on tensile bars having gage sections that were 2 in. long and 0.375 or 0.25 in. wide. In order to develop a series of grain sizes, the

Jan 1, 1957

By Robert A. Laurence

Ore deposits in the Southern Appalachians are ( 1) sedimentary or syngenetic, ( 2) epigenetic, and ( 3) residual. In general, deposits characteristic of high temperature and pressure are found in the Blue Ridge and Piedmont provinces and those of low and intermediate temperature and pressure, including the sedimentary ores, are found in the Valley and Ridge and Appalachian Plateaus provinces. Residual deposits are present throughout the area. Recognition of several periods of intrusion and metamorphism in the Appalachians has changed former concepts which held that most mineralization was of late Paleozoic age in a zonal pattern including all four provinces. Many deposits probably are of early or midPaleozoic age. Similarly, recent studies in geomorphology indicate that the formation of residual deposits is a continuous process and not related to specific cycles of peneplanation.

Jan 1, 1968

Page Foreword—H. Foster Bain........................ 9 Letter of Transmittal—F. Julius Fohs...................11

Jan 1, 1927

By Edward W. Parker

I. INTRODUCTION. AT the Seventy-sixth meeting of the Institute, held in New York, N. Y., February, 1899, I presented a, paper on this subject entitled, Coal-Cutting Machinery,' which has become somewhat out of date, in view of the decade's development in this feature of the coal-minim industry. It should be explained that the present paper is limited to the use of mining-machines in bituminous mines. Practically all of the anthracite mined is ?shot from the solid," no undercutting being done. Anthracite-mining is therefore not considered in the statistics or other references. The statistical record as compiled by the United States Geological Survey shows that in 1898, the year preceding the presentation of my former paper, there were 32,413,144 short tons of coal undercut by the use of machines. In 1907 the machine-mined coal-product amounted to 138,547,823 short tons. In sympathy with the general decrease in coal-production during 1908, the output of machine-mined coal decreased to 123,183,334 short tons, but the proportion of machine-mined coal to the total output, nevertheless, showed an increase, from 35.1 per cent in 1907 to 37 per cent in 1908. In 1898 only 19.5 per cent. of the total product was undercut by the use of machines. The number of undercutting-machines in use in the bituminous mines of the United States has increased from 2,622 in 1898 to 11,144 in 1907, and to 11,569 in 1908. The total production of bituminous coal in the United States in 1908 was almost exactly double that of 1898, while the machine- * Published by permission of the Director of the U. S. Geological Survey. 1 Trans.. xxix.. 400 to 4,59 (1899).

Sep 1, 1910

By R. H. Richman

Coarse-grained Fe-Ni-C martensites formed at subzero temperatures were strained in compression at room temperature and the plastic deformation modes examined as a funclion of carbon content. At very low carbon levels, defovmation occurs hy wavy slip; commencing at about 0.05 pct C, mechanical twinning accounts for an increasing proportion of the plastic flow. Beyond approximately 0.4 pct C the deformation appears to be entirely by mechanical twinning. The habit planes of the operative twin modes were determined to be (113), (0131, and "(089)" in decreasing frequency of occurrence. Some of the implicaticms of Ihe o6served deformation modes upon the structure and properties of ferrous martensites are discussed. METALLURGISTS have long sought to explain the mechanical properties of ferrous martensites, particularly the extraordinary hardness and strength of the high-carbon varieties. Until recently the lack of precise knowledge of the structure of martensite crystals was the most serious barrier to understanding; however, the advent of thin-foil techniques for transmission electron microscopy has removed much of the mystery from martensite structure. Observations by Kelly and Nutting,"' and many others since, indicate that Fe-C based martensite crystals are internally twinned to a degree dependent upon the carbon content, and that a martensite plate containing 0.8 wt pct C or more consists of a stack of twin-related lamellae with each lamella on the order of l00A thick. Such a structure would be expected to influence greatly all aspects of metallurgical behavior, and many of the properties of Fe-C based martensites have been rationalized accordingly. Recent independent experiments led Winchell and cohen3 to conclude that the strength of ferrous martensite is derived primarily from solid solution hardening of the iron lattice by interstitial carbon atoms. Strength contributions from precipitation, dislocation-atmosphere interactions, clustering, short-range order, crystallite size, and so forth, were considered to be of secondary importance. In the view of Winchell and Cohen, the twinned structure of martensite serves mainly to limit the effective length of dislocation lines in the lattice, and thereby confers an added measure of hardening. Few properties of metallic crystals are as sensitive to metallurgical structure as are deformation mechanisms. It is somewhat surprising therefore, that, except for metallographic evidence of mechanical twins in strained martensite,4 no systematic examination of plastic deformation

Jan 1, 1963

By A. L. Slaughter

The Homestake mine, located in western South Dakota, was discovered in 1876. The first reported production was in I 878. Total production through 1965 is 6,554,249 troy ounces of silver and 27,961,276 troy ounces of gold, worth $987,000,000 at present prices. Precambrian sedimentary formations at Lead total 20,000 feet. The Poorman Formation, the oldest, is chiefly ankerite carbonate. The Homestake Formation is iron-magnesium carbonate. The younger formations are argillaceous with some quartzites. The Cambrian Deadwood Formation unconformably overlies the Precambrian. All are cut by Tertiary intrusives. Sideroplesite schist of the Homestake Formation was converted to cummingtonite schist in the zones of higher-grade metamorphism. The Precambrian rocks show the effects of extreme isoclinal folding. A second stage of folding ( cross folds) may have been caused by the Tertiary intrusives. All folds plunge to the southeast. The Homestake ore bodies are pipe-like replacements of the Homestake Formation in zones of cross folding. It is believed that dilatation of the schists has increased permeability in these zones. Chloritization of the schists is the most widespread effect of the mineralization which is divided into four stages. Principal minerals of the first stage are quartz, chlorite, and arsenopyrite; in the second stage, quartz, ankerite, and pyrrhotite. In the third stage only pyrrhotite was deposited. The fourth stage followed the intrusions of Tertiary dikes and deposited mostly pyrite and calcite. Gold accompanies all stages and is always the last mineral to be deposited. It is most closely associated with arsenopyrite of the first stage but can be interpreted as having been deposited during the fourth stage and superimposed on the products of the earlier stages.

Jan 1, 1968

By M. E. Lombardi

THE Coalinga oil field is located on the west side of the San Joaquin Valley, California. The structure is in general a monocline, the edges of the oil horizon resting on the foot hills and dipping gently toward the east. One prominent anticline occurs plunging southeast. The earlier drilling was done in the foot hills comparatively near the outcrop and the wells were shallow. The sands were followed eastward and, in the case of the anticline, along the plunge, the wells becoming deeper and deeper until the depth of 4,000 ft. was reached and passed. There is nothing to show that the oil will not be found in quantity at still greater depth. In fact, some of the best producers have tapped the sand at close to 4,000 ft. The recovery of oil still farther to the east, and therefore at greater depth, seems to be mainly a question of drilling. In this territory the formations drilled through are chiefly sands and shales; they will not "stand up" in an open drilling hole; the casing has to be carried close to the bit, and it is always difficult to keep the casing free for any considerable distance. Ability to carry casing of comparatively large diameter without conductor pipes for distances of 2,000 or 3,000 ft. or over is desirable in such territory chiefly for two reasons. It makes it possible to enter the oil sand with a pipe of ample diameter; it eliminates one or more expensive strings of casing which act only as conductors for the water string, and furthermore, in territory where waters are encountered which corrode steel rapidly, it makes possible the construction of a rust- and alkali-resisting water string. It is always desirable to shut off top waters, which may lie within 100 ft. or less of the oil sand, with 10-in. pipe. Where the depth is so great that a practical weight of 10-in. pipe will not withstand the probable collapsing pressures, 8 ¼ in. at least is desirable. About the limit of rotary drilling to date in California seems to be the setting of the 10-in. string at 3,200 ft., although the rapid advance in rotary work during the past year seems to indicate that this depth may soon be increased. It is my purpose now, however, to treat only of cable-tool drilling.

Jan 2, 1915

By J. L. Kenty, J. P. Hirth

The concept of a critical super saturation, below which the nucleation rate is essentially zero and above which it is essentially infinite, is discussed with reference to vapor-solid nucleation. The necessary and sufficient conditions deduced for observations of this type of behavior are: 1) the nucleation rate must exhibit a sharp dependence on super saturation, 2) the growth rate must be sufficiently large that nuclei become observable in the time period of the experiment, and 3) the number of highly preferred nucleation sites must be small. Experiments reveal that the nucleation of silver on sodium chloride is visually detectable at all experimentally accessible super saturations and does not exhibit critical nucleation behavior. Failure to observe a critical super saturation is attributed to the insensitivity of nucleation rate to supersaturation as a consequence of the particular values of the contact angle and the surface free energy for this system. THE concept of a critical supersaturation, below which the nucleation rate is essentially zero and above which it is essentially infinite, arises naturally in homogeneous nucleation theory. Experimentally this type of behavior has been found by Volmer1 and others for water and other low surface tension liquids, as reviewed by several authors.2'3 The same type of behavior has been predicted and observed for heterogeneous nucleation of solids by Yang et al.4 and others,596 as also recently reviewed.2,7,8 In the work reported here on the heterogeneous nucleation of silver on NaC1, however, no critical super-saturation was found. Similar observations have been made recently for other systems.9-11 These results led to a reexamination of nucleation theory which revealed that there are conditions for which critical behavior is not predicted, either for homogeneous or heterogeneous nucleation. Although heterogeneous nucleation is of primary importance in this paper, some insight into critical behavior for such a case can be gained by considering homogeneous nucleation. Accordingly both types of nucleation theory are reviewed briefly. The requisite conditions for critical supersaturation behavior are then considered. The experimental results for the nucleation of silver on NaCl are presented and interpreted in terms of the theoretical presentation. REVIEW OF NUCLEATION THEORY There are essentially two approaches to nucleation theory, the so-called classical theory involving the concepts of bulk thermodynamics, and the statistical mechanical theory in which nuclei are regarded as macromolecules. The classical theory is based on the work of Volmer and Weber12,13 and Becker and. Doring14 and has been extended by Pound et al.15 The crucial assumption in the classical theory is that the small clusters or nuclei can be characterized by the same thermodynamic properties as those of the stable bulk phase. Thus, the nuclei are assumed to have a surface free energy, y, and a volume free energy of formation (relative to the vapor phase), ,, identical to that of the bulk. For deposition under low super-saturation conditions, the nuclei are large and this assumption is satisfactory. However, in many cases of interest, the nuclei contain only a few atoms and this assumption is highly questionable. The statistical mechanical models originated, for the specific case of a dimer as the critical nucleus, with the work of Frenkel16 and were extended later to larger sizes by Walton,17,18 Hirth19 and, more recently, Ht Zinsmeister. These models describe the nucleus in terms of a partition function, the estimation of which is tractable for clusters of 2 to 10 atoms, but extremely difficult for clusters larger than 10 atoms. Although the classical and statistical mechanical models are expected to apply for the limiting cases of large and small nuclei, both are uncertain for intermediate sizes. In this paper we shall treat only the classical model, recognizing that it is exact only for large nucleus sizes and regarding it as a phenom-enological description for small nucleus sizes. When analyses of experimental data using bulk properties show the nucleus size to be small, the resulting parameters should be regarded as largely empirical parameters describing the relative nucleation potency of the system. Considerable justification for the continued use of classical theory is provided by its general success in predicting nucleation behavior as a function of supersaturation and temperature. We emphasize that the qualitative features of the statistical mechanical models, particularly the critical super-saturation behavior that is central to the present work, are the same as those of the classical model. Of course, potential energy terms and surface partition functions replace the volume and surface energy terms of the latter model. The most recent versions of classical nucleation theory have been extensively reviewed.2,3,7 so that only the results are presented here. For homogeneous nucleation of a condensed phase from the vapor phase, the volume free energy change is ?Gv=vrT = =^ln£ [1] where v is the molecular volume of the condensing species. The supersaturation ratio,

Jan 1, 1970