Search Documents

By Meguru Nagamori

DURING the smelting of the sulfide ores of copper, nickel, and certain other metals, a matte phase is formed. For a better understanding of the physico-chemical properties of mattes, binary systems such as Cu-S, Ni-S, Fe-S, and so forth, should be studied, especially in the vicinity of liquid compounds such as Cu2S, Ni3S2, FeS, and so forth. These compounds are relatively stable in the solid state although they can exhibit appreciable deviations from stoichiometry. With small deviations from stoichiometry there are large changes in the activity of both sulfur and metal this is a characteristic of both solid and liquid sul-fides near the stoichiometric compositions. In the vicinityof molten Cu2S,1 for instance, the activity of sulfur increases about 100 times for a 0.012 increase in the mole fraction of sulfur and, correspondingly, the activity of copper decreases greatly. In this sens the minor deviations from stoichiometry should be carefully taken into account in studies of such metal-sulfur melts. Metal-sulfur melts may be considered to have properties intermediate between metallic solutions and molten salts, i.e., neither entirely metallic nor entirely ionic. The radius of the ion sZ- is 1.84 as compared with 1.04? for a single bond covalent s.2 It is therefore inferred that when the sulfur is more ionic its partial molar volume is larger, although metal-metal, metal-sulfur, and sulfur-sulfur interactions may bring about further complexities. Thus, it is to be expected that the molar volumes, which are derived from density-composition relations, will help in resolving the structure of the melts. In this study the maximum bubble pressure method with bubbling gases of H2, H2S, and Ar, .was employed to measure the density. EXPERIMENTAL Materials. Silver of 99.95 pct purity was melted in an alumina crucible and hydrogen gas was then bubbled through the liquid for the deoxidation. In preparation of Cu2S, electrolytic copper powder (>99.9 pct Cu) was mixed with precipitated sulfur and heated to 1200°C in an alumina crucible under a hydrogen atmosphere. Mixtures having the approximate compositions FeS and Ni3S2 were prepared by heating reagent grade electrolytic iron or reduced nickel powder with precipitated sulfur under a hydrogen atmosphere. The H2S gas was of 98.5 pct purity, the impurities being mostly CO2 and CS2 which hardly contaminate the melts. Apparatus. The crucible system is shown schematically in Fig. 1. To minimize the variation of melt composition during a density measurement, the apparatus was designed in such a way that either Ar, H2, H2S, or mixtures of these gases could be used as the bubbling gas. When the melt had a high partial pressure of sulfur, H2S gas was used. When the partial pressure of sulfur was so low that oxygen might dissolve in the melt, the use of H2 was preferred. In intermediate cases, argon or mixtures of H2-H2S were used. Density of Dibutylphtalate. Dibutylphtalate was used as the manometer fluid. Relative to distilled water, the density of the dibutylphtalate, pdib g per cc, was measured and found to be: pdib (25°C) = 1.046 i 0.002. With the use of the temperature coefficient reported by Kemppinen and Gokcen,3 the following value was

Jan 1, 1970

By L. G. Jones

An approximate method of calculation is developed in this paper which allows duplication of radial unsteady-state gas flow computer results where Darcy's law applies, such as those reported by Aronofsky and Jenkins and Bruce, Peaceman, Rachford, and Rice. Moreover, the new calculation method can be used to obtain results for radial unsteady-state gas flow obeying the quadratic flow law proposed by Duwez and Green. Means are discussed for predicting well behavior at single or superimposed flow rates in finite or infinite reservoirs, determining reservoir rock properties from well-test data, reproducing and interpreting back-pressure test data, and determining the radial extent and reserves of gas reservoirs from well-test data. Example calculations are presented for gas flow following both Darcy's law and the quadratic flow law. INTRODUCTION Since the publishing of U. S. Bureau of Mines Monograph 7,1 most gas-well testing methods have been based on the equation q = y (pl2 - pw2)a, where q = production rate, pl and pw, are formation pressure and sandface pressure, respectively, and y and a are constants to be obtained from test data. These methods, used for predicting both deliverability and "open-flow" capacity of gas wells, have been useful and accurate in many cases but unsatisfactory in others. Even at best, however, they do not supply information about the formation or lead to an understanding of nonsteady-state gas flow in porous media. Many theoretically based studies2-4 of gas flow obeying Darcy's law have been made.' Since the partial differential equations which result from combining Darcy's flow law with the continuity equation are nonlinear, most of the published research consists of either numerical solutions or analytical solutions for linear approximating equations. Such solutions have been of limited value in field work due to their unhandy form and their failure to correlate most field data. There is evidence5,6 which indicates that Darcy's law is inadequate to describe gas flow at some flow rates of practical interest. A quadratic flow law: which reduces to Darcy's law at low rates, is more successful in accounting for experimentally observed behavior. This flow law has been applied successfully to a few hypothetical reservoir cases in work which has recently been published.10 However, these numerical solutions of the equations involved have been successful only on a special analog computer. Routine applications to field cases would be awkward and have not been attempted. The present paper describes an approximate method for computing nonsteady-state gas flow solutions which has been completely successful in predicting the results for both Darcy flow and quadratic flow obtained by elaborate numerical methods. The new calculation method allows determination of the observable variables in gas-well testing at constant rates. It is similar to the scheme of using a succession of steady states suggested by Muskat7 in that it makes use of steady-state and material-balance equations. It also is similar to the work of Aronofsky and Jenkins2 in that the new method includes Aronofsky and Jenkins' stabilized flow equation as a special case. It improves upon both of these calculation schemes in that it accurately describes all portions of reservoir history and suggests means of determining reservoir rock properties from well-test data. This paper deals only with production from a reservoir, in which case the rate is defined as being negative. The reservoir studied here is a homogeneous, disk-shaped porous body of uniform thickness, with all boundaries sealed except the inner radial boundary of the well.

By T. Watanabe, S. Karashima, H. Oikawa

Creep tests of a! iron and its solid-solution Fe-Mo, Fe-Co, and Fe-Si alloys with bcc structure were conducted under constant stresses in ferromagnetic and paramagnetic temperature regions above 0.5T,(T, is the absolute melting temperature). It was found their high-temperature creep behavior changed in the vicinity of the magnetic transformation temperature, that is Curie temperature, TC. In the ferromagnetic region below the steady-state creep rates were lower than those expected from the extrapolation of the data in the paramagnetic region, the amount of decrease being affected by solute addition. Also, activation energies for steady-state creep were different in the two temperature regions. The observed changes were concluded to be due to the effect of ferromagnetism on diffusion. It is well-known that plastic deformation of metals and alloys in the temperature region where mobility of atoms becomes high enough is controlled by atomic diffusion." Many experimental results394 on fcc and hcp materials have been reported to confirm this view. In bcc metals and alloys, not much basic investigation of creep deformation has been performed. In particular, experimental work on iron5-&apos; and its alloys, covering a quite wide temperature range is extremely scarce. On the other hand, the effect of ferromagnetism on diffusion has recently been demonstrated in a iron and its alloys;&apos; it has been made clear that diffusion rates in ferromagnetic temperatur~e region are significantly lower than those expected from diffusion measurement in the paramagnetic region. Therefore, it is concluded that the magnetic effect influences the high-temperature creep behavior in a! iron and in its alloys. The present authors have conducted creep experiments on a iron and its solid-solution alloys over a very wide temperature range, and have demonstrated the magnetic effect. A part of the result has already been reported elsewhere.26 In this paper, the experimental results will be described in detail. While the manuscript was in preparation, a similar magnetic effect on creep deformation of a iron was reported by Ishida . Though their experiments covered an extremely wide temperature range, the creep stresses varied from several thousand psi to several ten thousand psi with decreasing temperature. Consequently, it may be said that there remain some questions concerning their results. I) EXPERIMENTAL PROCEDURE The materials used in the experiments were pure iron and its alloys; they were prepared by vacuum melting (10"" mm Hg) electrolytic iron (99.9 pct), molybdenum powder (99.9 pct), ultrapure silicon, and cobalt pellet (99.5 pct) in alumina crucibles. The ingots were hot-forged to plates 10 mm thick and 50 mm wide, and then were hot-rolled at about 700°C into sheets 1 mm thick. Creep specimens, 5 mm in width and 15 mm in gage length, were machined from the sheets. They were annealed at temperatures which were well above their respective recrystallization temperatures. The chemical compositions of the metal and alloys are shown in Table I together with their heat treatments. High-temperature creep tests by the use of a lever-type creep testing machine were carried out in argon atmosphere under constant tensile stress. In order to keep &eep stress constant within about *0.5 pct, stress change due to specimen elongation was compensated by tensile force of a stainless-steel bellows which was inserted between the loading lever and lower specimen grip with the assumptions of a linear relationship between change in cross section and strain and uniform strain along the section. Beyond the limit of compensation by the bellows, small amounts of load were removed after appropriate strains. The testing temperatures were maintained to within i2"C of the reported values. Creep deformation was auto-graphically recorded at the upper (moving) specimen grip using a linear differential transformer which was held by a stainless-steel rod mechanically connected to the lower specimen grip. It was also directly measured with a dial-gage reading to -& mm. 11) EXPERIMENTAL RESULTS AND DISCUSSION 1) Creep Curves of a Iron and Its Alloys. Creep curves of a! iron, Fe-Si, Fe-Co, and Fe-Mo (<2 at. pct Mo) alloys usually consisted of three stages, that is transient (primary), steady-state (secondary), and accelerating (tertiary) stages. An example is illustrated in Fig. 1 for a! iron. However, in Fe-Mo alloys with more than 2 at. pct Mo, an inverse transient creepZ8 was observed as indicated in Fig. 2. The inverse behavior, which varied with the amount of molybdenum, may be due to the substructure* in the annealed specimen as was sug-

Jan 1, 1969

By R. E. Maringer, B. A. Wilcox, A. H. Clauer, J. H. Sovik

Internal friction measurements from 25° to 1100°C have been made on specimens machined from TD nickel bar. The use of miniature torsional pendulum specimens alloived damping measurements to be made on specimens whose axes were parallel to the original bar axis, at 45 deg to the bar axis, and at 90 deg to the bar axis. There was a marked difference in damping with varying specimen orientation, and this was related to the pronounced micro structural anisotropy of this material. Varying the microstructure by cold working plus re crystallization annealing also greatly affected the damping behavior. Recrystallization essentially removed the broad peak found at 400° to 650°C in as-received TD nickel, and in addition greatly lowered the background damping. DlSPERSION hardened metals such as SAP-type alloys (Al + AI2O3) and TD nickel (Ni + 2 pet ThO2) have been developed primarily to improve high temperature strength properties. There have been numerous damping studies on SAP-type alloys,1"9 and one of these6 showed that the damping capacity was greater than that of 99.5 pet pure Al from 25° to 600°C. Several preliminary observations on TD nickel10 and an experimental Ni-ThO2 alloy11 indicated that here, too, the damping capacity was quite high. A high damping capacity in TD nickel, combined with its relatively good high temperature creep strength, could provide an additional benefit for some high temperature structural applications. This work was undertaken to study the internal friction behavior of TD nickel bar over the temperature range 25° to 1100°C. In Ni-ThO2 and Ni-Cr-ThOz alloys, other properties such as steady-state creep rate,12 creep rupture life,12&apos;13 modulus of elasticity,14 and ultimate tensile strength,14 are sensitive to orientation with respect to the primary working direction. Thus, in order to examine anisotropy effects in damping, studies were made on specimens machined with their axes parallel, at 45 deg, and transverse to the original bar axis. MATERIAL DESCRIPTION AND EXPERIMENTAL PROCEDURES The material used in this investigation was from the same £ in. diam TD nickel bar that has been studied previously.13&apos;15 The structure typical of the as-received TD nickel is shown in Fig. 1, and additional details of the structure can be found in Refs. 13 and 15. Elongated grains are parallel to the bar axis and are about 10 to 15 u long and about 1 u in diam. This structure is very stable, since no recrys-tallization or grain growth occurred after annealing for 3 hr at 1300°C.13 The total ThO2 content was 2.3 vol pct and the particles ranged in diameter from 100 to 1000. The average particle diameter was 370Å and the mean planar center-to-center particle spacing was 2340Å. To examine the influence of grain and subgrain structure on damping, a section of TD nickel bar was swaged and drawn at room temperature from 1/2 in. diam bar to 0.040 in. diam wire (99.3 pct re-duction in area). The structure in Fig. 2 resulted after the wire was annealed for 3 hr at 1250°C. The recrystallized grains were much larger than the grains in as-received bar, but still showed considerable elongation in the direction of working. A high

Jan 1, 1970

By G. S. Cole, G. F. Bolling

ThIS note accompanies a study of grain structure changes in metal ingots produced by the alteration of fluid motion.1 Although the Prandtl Number of aqueous solutions is much higher than that for metals, it is quite instructive to see the simulation of freezing, as pointed out by Jackson and coworkers.2-4 Accordingly we have observed the effects of natural thermal convection, the changes induced by a steady-state rotation in one direction, and the changes under oscillation.&apos; Temperature measurements were made under duplicate conditions whenever the visual observations appeared interesting. A solution of 15 pct NH4C1 in water was chosen. In each case the solution was preheated to 90°C in a 4-in.-diam Pyrex beaker filled to a level of about 5-in. depth and covered to prevent convective air cooling. The beaker was then placed in a container of iced brine, suitably arranged on a rotating table for movement about its cylindrical axis. Upon immersion in the brine under static conditions, fluid flow was observed near the wall of the beaker before the onset of crystallization, which generally commenced only after the temperature fell to 51.5"C. The region of flow extended about 1 mm from the wall and could not be observed elsewhere. The measured radial temperature increased sharply within 1 cm from the wall and thus over a distance considerably greater than that observed for the flow. However, we note that this difference of approximately one order of magnitude between hydrodynamic and thermal boundary layers should be expected for aqueous solutions, in contrast to metallic liquids. Beyond this layer the temperature was isothermal at a given height and in general nearly 10°C warmer than at the wall. The overall visual observation was therefore supported quite well by temperature measurement. There was also a vertical temperature gradient of nearly 2°C per cm throughout the liquid increasing from the colder bottom; this of course could not be observed visually. Eventually crystals precipitated from solution. (It

Jan 1, 1968

By G. V. Jere, V. Krishnan, C. C. Patel

Standard free energy and standard enthalpy changes as a function of temperature have been calculated for the chlorination reactions of different oxides constituting columbite and tantalite. The tallies of standard lee-energy change (F) indicate the possibility of pvefeential chlorination of different oxides but the ease 0.f chlorination of columbium pentoxide at about 250°C and the chlorinating tendency of columbium pentachloride in promoting the chlorination of tantalum and other metal oxides, p7-evetzt the separation of columbiu?n and tantalum from other oxides and pom each othel.. It is likely that low temperatuves of chlorination and continuous 1err2oval of columbium pentachloride from the ..eaction zone may help partial separation of columbium from tantalum as well as from titanium. The standavd enthaply change (AH?) values shotr that 1ou.-temperature chlorination around 300" to 500°C is likely to sustain the chlorination , without external heating. COLUMBIUM (niobium) and tantalum metals, their alloys and interstitial compounds are finding extensive uses in nuclear reactors and high-temperature equipment.la-3 These metals also find uses in chemical process plants, electrical rectifiers and capacitors and as "getters" in electronic tubes.la With the development of Kroll process of reduction of volatilized titanium tetrachloride by magnesium for the production of titanium metal, chlorine metallurgy is receiving greater attention. Chlorine metallurgy has several advantages, the foremost amongst them are: the ease of chloride formation, separation of the different constituents of minerals by selective chlorination, and the reduction of the chlorides in vapor phase to the respective metals. Recently, Si-bert, Kolk, and Steinberg4 have considered a number of methods for the preparation of columbium metal and the most promising is found to be the halide reduction. Since the minerals columbite and tantalite are comparatively abundant in nature, the future of the metallurgical processes depends on the utilization of these minerals for the production of columbium and tantalum chlorides by chlorination. In this paper, an attempt has been made to interpret thermodynamically the chlorination of individual oxides constituting columbite and tantalite, with the help of the recent thermodynamic data.5-8 For this purpose, standard free energy and standard enthalpy changes of the chlorination reactions of the oxides with chlorine, both in absence and presence of carbon as the reductant, have been calculated as a function of temperature and represented graphically. Similar calculations for the reactions employing carbon tetrachloride and carbonyl chloride as chlorinating agents have also been incorporated in this paper. REPORTED WORK ON CHLORINATION Cuvelliezg has patented a process for the separation of columbium and tantalum from their concentrate, wherein 75 pct Cb05 is claimed to be chlorinated at 1050°C in the course of 7 hr using chlorine or chlorine containing nonreducing gases, the products of reaction being CbC1, or CbOC1,. At this temperature, Ta,05 is claimed to remain unaffected. It is further claimed1° that at higher temperatures, the proportion of Ta205 chlorinated increases while that of Cb205 diminishes. During the studies on the action of chlorine on individual metal oxides, Kangro and Jahn" have observed that Ta,05 is not chlorinated even at 1200" in the stream of chlorine, while 75 pct of Cb,05 is converted into CbOC1, around 900 to 1100°C. The chlorination of Cb205 by chlorine in the presence of carbon, investigated by Lind and Ingle,&apos; and

Jan 1, 1962

By S. R. Elliott

The Spies mine is located in the eastern half of the northwest quarter of section 2443-35, near the village of Iron River, Mich., and is operated by The Cleveland-Cliffs Iron Co. Speaking generally, the jasper hanging walls of most of the deposits in the Iron River district dip at a steep angle and are exceedingly strong, standing without caving, even after mining has been continued for years and after large excavations have been made. The ore is fairly hard and tough and contains no slippage faces. It occurs in large masses, which are often egg shape, with the smaller end down, and can be mined in open stopes without the use of timber. The common system employed in the district is the shrinkage stope, or some modification of it. The Spies system was developed to utilize the advantages of the open-stope method and to avoid the disadvantages of the shrinkage stope. The Spies shaft was sunk to such a depth that the bottom, or third level, was in rock at a short distance below the bottom of the orebody, the shape and extent of which had been previously determined by diamond drilling. This is shown in plan and by the ore contours at the first, second, and third levels in Fig. 1, and in section in Figs. 2 to 7. In order to provide the necessary mills and raises, three parallel crosscuts were driven on 25 ft. centers on the bottom level. Drifts on the second and first levels were driven to the orebody and followed the foot wall in a southerly direction to the end of the ore. In crosscut 3, Fig. 1, raises 30, 40, 50, and 60 were carried up on the foot wall and holed into the second level, and were ultimately carried up and holed into the first level. These foot-wall raises carry the pipes and ladders, provide a means of ventilation, and furnish safe communication to all working places in the stope. From crosscuts 1, 2, and 3, raises were completed to a height of 32 ft., or the elevation of the first sublevel. They were then connected by east and west crosscuts to the main foot-wall raises 30, 40, 50, and 60, shown in Fig. 4. The crosscuts in raises 1 to 5 were then driven west and the

Jan 1, 1923

By S. R. Elliott

The Spies mine is located in the eastern half of the northwest quarter of section 2443-35, near the village of Iron River, Mich., and is operated by The Cleveland-Cliffs Iron Co. Speaking generally, the jasper hanging walls of most of the deposits in the Iron River district dip at a steep angle and are exceedingly strong, standing without caving, even after mining has been continued for years and after large excavations have been made. The ore is fairly hard and tough and contains no slippage faces. It occurs in large masses, which are often egg shape, with the smaller end down, and can be mined in open stopes without the use of timber. The common system employed in the district is the shrinkage stope, or some modification of it. The Spies system was developed to utilize the advantages of the open-stope method and to avoid the disadvantages of the shrinkage stope. The Spies shaft was sunk to such a depth that the bottom, or third level, was in rock at a short distance below the bottom of the orebody, the shape and extent of which had been previously determined by diamond drilling. This is shown in plan and by the ore contours at the first, second, and third levels in Fig. 1, and in section in Figs. 2 to 7. In order to provide the necessary mills and raises, three parallel crosscuts were driven on 25 ft. centers on the bottom level. Drifts on the second and first levels were driven to the orebody and followed the foot wall in a southerly direction to the end of the ore. In crosscut 3, Fig. 1, raises 30, 40, 50, and 60 were carried up on the foot wall and holed into the second level, and were ultimately carried up and holed into the first level. These foot-wall raises carry the pipes and ladders, provide a means of ventilation, and furnish safe communication to all working places in the stope. From crosscuts 1, 2, and 3, raises were completed to a height of 32 ft., or the elevation of the first sublevel. They were then connected by east and west crosscuts to the main foot-wall raises 30, 40, 50, and 60, shown in Fig. 4. The crosscuts in raises 1 to 5 were then driven west and the

Jan 1, 1923

By G. L. F. Powell

TURNBULL and Cech1 reported undercooling small droplets (approximately 50 mp in diam) of a large number of metals by approximately 0.18 TE (TEoK = the equilibrium freezing point). This was considered to be the undercooling for homogeneous nucleation in

Jan 1, 1968

By H. Dykstra

Calculated wellbore pressures were obtained for parameters of radilcs ratio and permeability. In all cases bur two, after-production was allowed to occur for one day. The calculated pressure build-up data were compared with actual pressure build-up data from a condensate well. The paper discusses the comparison, gives reasons for, inability to match calculated (2nd actual data, and presents conc1usions derived from the comparison. INTRODUCTION Considerable information has been published on the decline in wellbore pressure for oil and gas fields resulting from production of fluids. Considerable information also has been published on pressure build-up for oil fields, but relatively little has been published for gas and condensate fields. Perrine&apos; summarized the equations derived for pressure build-up in oil wells and showed how the different methods could be applied. On the other hand, very little theoretical information has been published on pressure build-up in gas or gas-condensate wells.2-4 Tracy,&apos; by pointing out the similarity between the equation describing oil wellbore pressure decline and the equation describing gas wellbore pressure decline, showed how methods of pressure build-up analysis could be applied to a gas well. In analyzing pressure build-up data for gas or gas-condensate wells, it would be very desirable to compare actual pressure build-up data with calculated pressure build-up data. Such a comparison would lead to a better feeling for the quantitative picture of gas-well build-up curves and would help to establish a degree of confidence in a given build-up curve. This paper discusses the comparison and presents conclusions made from it. Calculated wellbore pressures are given for parameters of radius ratio and permeability. In all cases but two, after-production was allowed to occur for one day. The work was done in an attempt to evaluate the reserves of a gas-condensate field. As will be discussed later, it was not possible to make an evaluation. METHOD OF CALCULATION The method used for solving the depletion and pressure build-up behavior for a gas-condensate well was that developed by West, Garvin and Sheldon.5 or the IBM 704 computer program used, it was assumed that liquid condensing out of solution would have only a minor effect on the flow behavior. Therefore, the field was treated as having single-phase flow, with the gas saturation S, remaining constant at unity minus the connate-water saturation Sw. As will be discussed later, this may not have been a good assumption. It also was assumed that oil production could be considered as equivalent gas production by using a conversion factor based on an analysis of the liquid produced. An outer boundary condition of no-flow was assumed. BASIC DATA The data required for the study were reservoir properties, fluid properties and production data. Reservoir properties included the following: thickness h, 179 ft; porosity, 0.194; connate-water saturation, 0.43; gas saturation, 0.57; permeabilities k, 1.0, 0.5, 0.25 and 0.15 md; radius ratios re/rw, 800, 1,000 and 2,000; wellbore radius rw, 5 in.; initial reservoir pressure P, 6,529 psia; and reservoir temperature, 272°F. The selection of permeabilities was based on core-analysis data showing an average air permeability of about 2 md. With a relatively high connate-water saturation, the average effective gas permeability would be about one-half, or less, of the air permeability. The selection of radius ratios was based partly on the observed rapid decline in wellbore pressure during production and partly on the fact that the well was believed to be located in a relatively small fault block. Reservoir fluid properties were obtained from a reservoir fluid study on a recombined sample of gas and condensate. Gas formation-volume factors were calculated from pressure-volume measurements made at reservoir temperature. Gas viscosities were calculated by the method of Carr, et al,G from an analysis of the re-combined sample. These data are shown as a function of pressure in Table 1. The production schedule from the gas-condensate

By M. C. Udy, F. W. Boulger

AN incomplete phase diagram for the U-Ti systern was determined earlier 1 and more recently, a tentative diagram was presented for the uranium-rich end of the system.&apos; In the present re-examination of the whole system of U-Ti alloys, high purity materials were used. Melting stock for the alloys was high purity uranium, containing about 0.09 pct C as the only appreciable impurity, and high purity iodide-process titanium purchased from New Jersey Zinc Co. Both metals were cold rolled to about 1/6 in. thickness, sheared to about I/&apos; in. squares, and cleaned by pickling. The alloys were arc melted under a helium atmosphere in a water-cooled copper crucible. A thoriated-tungsten electrode was used. The furnace chamber was evacuated, then flushed with helium, prior to each melting. It was finally filled with stagnant helium at one atmosphere pressure. Each alloy was remelted three times after the original melting, to insure homogeneity. The alloy button was turned bottom side up before each re-melting operation. Some 22 alloys were examined. Their compositions were spaced at appropriate intervals between 100 pct Ti and 100 pct U. Analyses were made on chips taken after fabrication. The major contaminant was carbon, which varied from 0.03 to 0.08 pct. It appeared in the microstructure as titanium carbide. Alloy compositions were calculated to a carbon-free basis for consideration on the diagram. Tungsten and copper, possible contaminants from the melting operation, were generally less than 100 parts per million each. Fabrication All alloys were forged and rolled to bars approximately V8 in. square. They were clad either in SAE 1020 steel or in a 5 pct Cr-3 pct Al-Ti-base alloy, depending on the fabrication temperature. A temperature of 1800°F (980°C) was used for alloys near the compound composition. This necessitated using the titanium-base alloy, since iron reacts with titanium at this temperature, producing a low melting alloy. Other alloys were fabricated at 1450°F (790°C), using steel jackets. No iron-titanium reaction occurred at this temperature. The jackets were welded in place in an argon atmosphere. Those alloys sheathed in steel were declad and then reclad between rolling and forging operations. On the other hand, those clad with the titanium alloy were cut to a roughly rectangular shape prior to clading and were then carried through both the forging and rolling operations without opening. Those alloys near the compound composition were found to be cracked when the clading was removed. The cracked materials had been plastically deformed, however, and at least some of the cracking had OCcurred during cooling. Heat Treatment The rolled bars, after being declad and shaped to remove surface contamination, were all given an homogenizing treatment of 160 hr at 2000°F. (Samples were taken for analysis following the declading and shaping operations.) All were heat treated at the same time in one furnace, but each was sealed in a purified argon atmosphere in an individual Vycor glass tube. Argon pressure was such that it was approximately atmospheric at temperature. One end of each tube contained titanium chips and this end was heated to 1200°F (650°C) for 10 min prior to the heat treatment. This purged the atmosphere of residual reactive gases. The balance of the tube was warmed during the purge to liberate adsorbed moisture and gases, which also reacted with the hot chips. The bars were furnace cooled from the homogenization treatment. Specimens of each alloy were water quenched after 2 hr heating at 1000°, 1200°, 1400°, 1600°, 1800°, and 2000°F (540°, 650°, 760°, 870°, 980°, and 1095°C). In addition, some were treated at intermediate temperatures of 1300°, 1500°, and 1700°F (705", 815", and 925°C) and at 2150°F (1175°C). Specimens, about &apos;/s in. cubes, were cut from the bars, sealed in individual Vycor tubes, and heat treated as described. All specimens heat treated at the same temperature were processed together. Samples were quenched by breaking the Vycor tube rapidly under water. Metallographic Examination Specimens were mounted in bakelite and ground wet on 180 grit paper held on a 1750 rpm disk. They were then ground wet by hand, using 240, 400, and 600 grit papers. The rough grinding was continued long enough to get well below the surface. Specimens were mounted separately because of the variation in the rate of etching between alloys. The specimens were polished with rouge on a 4 in., 1725 rpm wheel covered with Miracloth. Alloys on the titanium side of the compound composition were etched with a solution of 2 pct hydrofluoric acid in water saturated with oxalic acid. A few crystals of ferric nitrate were added as a bright -ener. Specimens were immersed 5 sec, polished to remove the etch, then re-etched. With the higher titanium alloys, it was often necessary to start the etch on the polishing wheel, because of the formation of a passive film. In some instances, a plain 2 pct hydrofluoric etch was satisfactory. For the alloys on the uranium side of the compound, a distinction between the compound and the uranium phase developed after standing a short time in air. This could be hastened by the application of heat, such as obtained by placing the specimen on a radiator. A deep etch was necessary to develop details in the uranium-rich phase, such as the Widmanstaetten pattern sometimes obtained by quenching y uranium. A 2 pct hydrofluoric acid solution was used for this deep etching.

Jan 1, 1955

By V 7. 0 / 300 dpi

WHEN the copper smelters were built, in Montana, all of the refractory products which were used in their construction were shipped in from Eastern factories. It was apparent that if a material suitable for the manufacture of these products could be found within the State, a saving of freight could be effected and a new industry built up. Prospecting for such materials was started and experiments were made with samples from numerous deposits. Considerable effort and funds were expended in an attempt to manufacture silica brick from Dillon quartz, a light colored sandstone that is found near Dillon, Mont., on the Oregon Shortline railroad. As a brick material the Dillon quartz was a failure, but it has proved very satisfactory as a silica cement. It is now being used in laying silica brick and for reverberatory furnace bottoms. A bed of quartzite that is particularly suited to the manufacture of high-grade silica brick -was finally discovered at Browns Spur, 6 miles west of Anaconda. The material from this deposit is now being used in the manufacture of the Anaconda silica brick, which have gained a wide reputation for heat-resisting and lasting qualities. The analysis of all average sample of this quartz is: SiO2,, 96.7; Fe203, 0.3; Al203, 2.5; CaO, 0.3 per cent. The very low percentage of fluxing ingredients makes this a most refractory material. All of the Anaconda silica brick are hand molded. Various types of brick machines have been tried, but the hand-mold process proved the best suited to the manufacture of silica brick from this material. The silica is first put through a jaw crusher and is then clumped into wet pans, where 4 per cent. of lime paste is added, to produce a bond. Without the lime the. material would not be plastic enough to mold. After a few minutes&apos; grinding in the wet pans the material is conveyed to the molder, who forces it into the molds by hand. The brick are then dumped on pallets and placed in the drier, where they are left until dry enough to be set in the kilns. Some of the brick are re-pressed before being dried. They are burned about five days, in round down-draft kilns. It is not necessary to have as much heat in the kilns as the brick will be subjected

Jan 9, 1913

By J. C. HEILMAN

THE Tri-State district, named from its situation in three States, lies in the northeast corner of Oklahoma, the southeast corner of Kansas and the adjacent part of Missouri east of the common corner of the above States. Production in the past eighty years has come from scattered mines within an area of some 35 miles east and west, by 25 miles north and south, although the actual area of the mined ground is but a small fraction of this territory. The land is leased from the individual land-owners, and the size of the tracts varies from 4.0 to 200 acres, the smaller sized tracts predominating. The leases usually call for a royalty of 7% to 15 per cent of the gross receipts of the concentrates, continuous operation during the life of the lease and specifically set out that no ores can be brought in from a foreign lease for custom milling nor can any ore be removed from the lease for milling. The ownership of the tailings remains with the land-owner.

Jan 1, 1931

By Robert Ammon

The milling practice at Mascot, at present, consists of dry crushing to % in., jigging, fine grinding, and flotation. The ore arrives at the mill from two mines, No. 1 mine shaft being located in the mill proper, and No. 2 mine shaft being situated about 2000 ft. east of the mill. No. 2 mine is served by a coarse-crushing plant and aerial tramway to the mill bins. In jigging the No. 2 mine ore, 50 per cent. of the mill feed is rejected by the jigs as a jig tailing ranging from 5/8 in. to 10 mesh; the balance of this ore, after removing a jig concentrate, is ground to flotation feed. In jigging No. 1 mine ore, approximately 80 per cent. of the mill feed is rejected as a coarse jig tailing, and the balance is ground to flotation feed without the removal of a jig concentrate. The difference in the treatment is due to the fact that No. 2 mine ore carries a higher content of zinc than that from No. 1 mine. Of the total concentrates produced, 30 per cent. is made on jigs and 70 per cent. by flotation. At present, 1350 tons of No. 2 ore and 800 tons of No. 1 ore are treated each 24 hours. The recoveries for a typical week are as follows: Heads.......................... 3.55 Jig concentrates................ 61.30 Jig tails......................... 0.80 Flotation concentrates........... 60.60 Flotation tails................... 0.09 Extraction..................... 86.50 The associated minerals are a straw-colored sphalerite, dolomite, calcite, pyrite, quartz, and a small amount of greenockite, which occurs as a stain and sometimes small crystals along with sphalerite, but is comparatively rare. Pyrite is present in small quantities, usually less than 0.5 per cent.; quartz occurs in bands a few inches thick. A complete analysis of the ore is as follows: PEr Cent. Per Cent. Calcium carbonate.............. 48.11 Zinc sulfide.................... 5.43 Magnesium carbonate........... 35.36 Cadmium sulfide............... Nil Silica.......................... 8.73 Lead sulfide................... Nil Alumina....................... 1.04 Iron oxide...................... 1.33 Total....................... 100.00

Jan 1, 1925

By Henry Drinker

The Institute has lost a valued member by the death of Eckley B. Coxe, Jr. He bore the name of one who was largely instrumental in founding the Institute, and to whose support and guidance as active member, Vice-President, and President, the Institute owes. much. Eckley B. Coxe, Jr., was the nephew of the late Eckley B. Coxe. He held a large interest in the coal estates owned and developed by his family, and he was thus naturally led to take a continuing interest in mining matters, and for years and up to the time of his death was a full member of the Institute. He died at his residence, Drifton, Pa., on Sept. 20 last, aged 44. He was a member of the class of &apos;93 of the University of Pennsylvania,. of which great institution he was a devoted alumnus. His educational and charitable activities were numerous, but his chief life-work and interest was in archeological investigation and research in Egypt, carried on through the Museum of the University of Pennsylvania of which Museum he was President. The discoveries made by the various expeditions financed and directed by him, and the notable publications issued by his direction and at his expense, chronicling the results, are among the most important researches ever made of buried Egypt. Mr. Coxe was a member of the International Historical Society and of many educational and charitable organizations. By his will, among other bequests, he left $500,000 to the Museum of the University of Pennsylvania and $100,000 to the University, the income of the latter fund to be applied to increasing the salaries of the professors of the Institution. He also left $100,000 to the Children&apos;s Hospital of Philadelphia, of which he was a manager, and in addition thereto $10,000 of which the income is to be applied in providing Christmas presents for .the child patients, and in providing an annual dinner for the patients and attendants of the hospital. He bequeathed $50,000 to Leonard Hall, an associate mission of the Episcopal Church, at South Bethlehem, Pa., $25,000 to the Epileptic Hospital and Colony Farm (Philadelphia) ; $50,000 to the Philadelphia Orthopaedic Hospital and Infirmary for Nervous Diseases; $15,000 to the United Charities of Hazleton, Pa., the income to be applied to the salaries of nurses; and $25,000 to the Mining and Mechanical Institute of the Anthracite Coal Region of Pennsylvania, founded by his uncle, Eckley B. Coxe, and of which Eckley B. Coxe, Jr., was an active trustee up to the time of his death. This Institute is known as one of the best preparatory schools for technical education in Pennsylvania, and is mainly devoted to extending an opportunity for education by day and night schools to the boys and young men of the Anthracite Region. Its principal is an alumnus of Lehigh University; it has an able local Board of Trustees, and an Advisory Board consisting of the Provost of the University of Pennsylvania, the President of Lafayette College, and the President of Lehigh University, all three of which institutions have established prize scholarships in the institute. Mr. Coxe carne of a distinguished ancestry, the record of which is fully given in the biographical notice of his uncle, Eckley B. Coxe, by Dr. R. W. Raymond, in Vol. XXV of the Transactions.`

Jan 12, 1916

By J. W. Downey, J. B. Darby, L. J. Norton

THE only previous investigation of the phase equilibria in the Ta-Pd system was reported by Greenfield and Beck.1 Their work (actually a portion of a much broader survey) was limited to the composition range 50 to 75 at. pct Ta and to a single temperature, 1000°C. The results indicated that no intermediate phases were present at this temperature. They pointed out that this was an unexpected result in view of the fact that niobium, which belongs to the same group in the periodic table as tantalum and has essentially the same atomic size, forms a o phase with palladium.&apos; Also, tantalum in combination with rhodium,&apos; iridium,&apos; or platinum&apos; stabilizes the s phase. By analogy, the Ta-Pd system would also be expected to contain a s phase. The present investigation was therefore undertaken to explore more fully the phase relationships in this system. Alloys were prepared by arc melting on a water-cooled copper hearth in an argon-helium atmosphere. The purity of the starting materials was greater than 99.9 pct. The weight losses on melting were less than 1 pct and therefore the alloys were not analyzed chemically. Specimens were wrapped in molybdenum foil, encapsulated in quartz capsules under a vacuum of at least 1 x 10-5 mm of Hg, annealed as indicated in Table I, and water quenched. Optical and X-ray metallography were used for identifying the phases present in the annealed and quenched alloys. The alloys were resistant to attack by several acids; however, a sodium cyanide electroetch and an immersion etch containing 1 part HF, 1 part HNO3, 2 parts H2SO4, and 5 parts H2O by volume were found satisfactory. The X-ray diffraction patterns were taken with a Straumanis-type Debye-Scherrer camera and filtered copper or chromium radiation. A summary of the phases found in this investigation is presented in Table I. No attempt was made to determine the composition limits of the various phases. The present results indicate that this system consists of two terminal solid solutions separated by at least four intermediate phases at the approximate compositions Ta3Pd, -TaPd, TaPd,, and TaPd3. The Ta-rich solid solution, containing less than 10 at. pct Pd at 1150°C, is in equilibrium with a o phase which is stable in the vicinity of 25 at. pct Pd. The latter phase is also in equilibrium with a bct phase at the equiatomic composition. At high temperatures it appears that the Pd-rich solid solution extends to at least 66.6 at. pct Pd and is in equilibrium with the bct phase. When annealed at 900°C, a sample containing 66.6 at. pct Pd transformed to an unidentified phase designated as X. An X-ray diffraction pattern of this phase contained sharp low-angle lines while the high-angle lines were characteristically diffuse. The observed d-spacings and relative intensities for lines in the low-angle region are presented in Table 11. In the vicinity of 70 at. pct Pd an intermediate phase having the TiA13-type structure is formed. It is stable to at least 1100°C, and presumably dissolves congruently into the ter-

Jan 1, 1963

By Walter Kauzmann

ALL viscous or plastic flow of incompressible matter is the result of shear strain; the changing shape of any body that is being plastically deformed can be completely described in terms of the shear strain occurring at each point in the body.[t] Furthermore, the relative amounts of shear strain occurring in different parts of a body under stress depend upon the relative rates of shear strain at those different points, so that if the dependence of the shear rate of any material on the temperature, shear stress, previous history, etc., were understood, the principles of plastic deformation would be known, and we could calculate how a body made of a given material, having a given shape, and subject to a specified system of forces, would change its shape with time. It may be said, then, that the problem of plasticity resolves itself into, first, the problem of the rates of pure shear processes, and second, the application of what is known about pure shear to actual cases. It is the purpose of this work to investigate the former problem -i.e., the dependence of shear rates on temperature, stress, etc.-from the standpoint of recent developments in the field of chemical-rate theory and with particular reference to the phenomena occurring in the creep of metals and in the plastic flow of crystalline solids in general. It is left for the mechanical engineer, and perhaps the expert in hydrodynamics, to deal with the problem of applications1 RESOLUTION OF MACROSCOPIC SHEAR INTO MICROSCOPIC MOVEMENTS; RESEMBLANCE TO CHEMICAL REACTIONS Just as any large body is made up of many small units, or atoms, so macroscopically observable shear is the result of many microscopic unit shear processes; just as the understanding of the behavior of large bodies demands the understanding of the atoms of which it is made, so the understanding of macroscopic shear demands the understanding of these fundamental unit processes. The study of shear from this "atomistic" point of view has made considerable progress. There has been fairly complete understanding of shear processes in gases for a long time, at least for nonturbulent flow, as a chapter on gaseous viscosity in any text on the kinetic theory of gases will prove. In recent years Andrade2 and Eyring3 have presented important theories for the flow of liquids and amorphous solids. Becker,4 Orowan,5 Taylor,6 Burgers,7 and Kanter8 have considered the

Jan 1, 1941

By D. N. Witman

ONE of the special uses to which the electric furnace has been put recently is the melting of an alloy of nickel and cast iron for the production of electrical-resistance grids. The metal sections of these grids, Fig. 1, are quite uniform for each pattern, but there is, among the various patterns, a variety of thicknesses. The cross sections vary from 1/2 by 3/16 in. to as small as 1/8 by 1/8 in. The electrical resistance f a perfect casting lies within 10 per cent. above or below the fixed listed resistance for each pattern. Good molding is essential to success in the making of these grids, for with absolutely correct metal, a variation of 0.01 in. in width and thickness of section on some of the patterns may mean as much as 12 or 14 per cent. variation in resistance. The service for which these castings are intended demands that the metal, even in the smallest castings, be very soft, showing an open, gray, highly graphitic structure in order that they may be resistant to shock, and stand up well under rough usage. The metal used for this purpose is a gray iron alloyed with 4 to 5 per cent. of nickel, which element, when the composition of the alloy is correct, imparts toughness and pliability to the metal and helps to overcome the tendency of metal to run white and become brittle because of the rapid cooling action of the sand mold. When cold, these castings can be twisted into various shapes, taking a permanent set without breaking. The alloy has approximately double the electrical resistance of ordinary cast iron. The metal specification is as follows: PER CENT. Silicon 2.40 to 2.60 Sulfur Under 0.05 Phosphorus Under 0.08 Manganese Under 0.40 Total carbon 3.60 to 4.00 Nickel 4.00 to 5.00 Copper 0.50 to 0.70

Jan 8, 1921

By V. (“Viv”) R. Forbes

[ ] INTRODUCTION "The Liberal Party believes that the State&apos;s mineral resources belong to the people of Queensland and therefore it is essential that the state, on their behalf, obtains maximum benefit from the development of those resources." (Liberal Party, 1980 "Mineral Resources Policy" p.2). "Unless sound policies are implemented.... increased production of minerals will benefit only the already wealthy and the lucky few... A resources tax is essential to ensure that above normal profits are shared by the whole community.... Labor policies on taxation must ensure an adequate return from mining developments to the Australian people." (Labor Party Policy Paper, May 1982 "National Issues relating to rapid expansion of mineral production during the eighties". p.1, 37, 47). Judging from these statements, key political parties in Australia believe that mining profits are lightly taxed and that shareholders get most of the benefits. THE REALITY The Government Share of Income statement in Table 1 attempts to measure the government share of the income generated by the "Big Five" Australian mining companies - Broken Hill Pty Ltd. (BHP), CRA Limited, Utah International, MIM Holdings Ltd., and Western Mining Corporation ("WMC"). These companies control over 70% of Australia&apos;s mining industry including all the most profitable mining operations. They dominate the mining and processing of iron and steel, aluminum, manganese, coal, oil and gas, copper, lead, zinc, silver, nickel, gold, ferro-alloys and salt in Australia. They are also major world exporters of most of these products. They are thus a representative sample of the profit-earning side of the Australian mining industry. In their two most recent financial years these five companies had income before tax of A$6,980 million. The Government share of this income was A$6,285 million or 90%. The total market capitalisation of the Big Five is about A$8,480 million. (December, 1982). Governments thus consumed the equivalent of 82% of their total value in just two years. This was taking place while the politicians drafted the above statements calling for an "adequate" share for the people.

Jan 1, 1985

By Haim H. Chiswik, Ralph Hultgren

In recent years considerable attention has been devoted to the development of new commercial uses for silver, chiefly because of lowered prices and large stocks of the metal. This has led to increased interest in the phase diagrams of silver alloys. The silver-lead diagram is reported&apos; to be of the simple eutectie type, but no measurements of the solubility of lead in silver have been made. The solubility of silver in lead has been estimated2 from diffusion experiments and resistance measurements to vary with temperature from 0.09 to 0.18 atomic per cent (0.05 to 0.10 weight per cent). Silver-rich silver-lead alloys have recently been recommended as high-strength bearing metals3 The silver-bismuth diagram is similar.&apos; The solubility of bismuth in silver. has been estimated to be about 5.5 weight per cent on the basis of X-ray work.4 Matthiessen6 found a solubility of silver in bismuth from 0.25 to 0.50 per cent by conductivity measurements. Silver and thallium form the same type of diagram,&apos; with no data on their mutual miscibilities. We have studied the first two of these diagrams by X-ray methods, verifying their main features and determining the solubilities of lead and bismuth in silver at several temperatures. We also determined the solubility of thallium in silver at one temperature. The solubilities of silver in lead and in bismuth were found to be too low to be detectable. Materials and Methods Mallinckrodt precipitated silver, analytical reagent, was used. Maximum impurities listed on the label were: chloride, 0.005 per cent; copper, 0.001; iron, 0.002; other heavy metals (as Pb), 0.002; and sulphate (SO³), 0.05. The lattice constant was found to be a0 = 4.0782 $., in good agreement with the value of Jette and Foote,6 a0 = 4.0779 A., for

Jan 1, 1940