Search Documents

By D. H. Baldwin, R. E. Reed-Hill

DURING the course of experiments involving oxygen equilibrations with a high-purity Pd-5 at. pct Rh alloy, the appearance of a subscale was noted. Most of the heat treatments in a pure oxygen atmosphere were performed at 900°C. The presence of the subscale was noted when the oxygen partial pressure was in excess of approximately 95 mm, up to 1 atm, the highest pressure used. According to available thermodynamic information' on the free energy of formation of Rh2O3 (the only reliably reported solid oxide of rhodium), this oxide should not be stable under these conditions, nor, of course, any oxide of palladium. Extraction of the subscale from the matrix was affected by treatment with aqua regia, and the resulting X-ray diffraction powder pattern is shown in Table I. This pattern is not that of Rh2O3, nor that of any known rhodium or palladium oxide. It can be indexed on a hexagonal lattice with a. = 5.22Å and co = 6.0Å. In addition to this unknown material, there was a weak Rh2O3 pattern. An X-ray fluorescence analysis of the powder gave 3214 palladium counts per sec and 5381 rhodium counts per sec, thus indicating the likelihood of a double oxide of palladium and rhodium. In view of the fact that the above result was obtained on a single sample, it is perhaps best not to insist upon the above ratio of about 0.6, but possibly to tentatively assume 0.5 or 1/1. The small amount of Rh2O3 in the X-ray pattern might have occurred on cooling, and it seems possible that the double oxide, below some temperature level, is not as stable as Rh2O3. To examine this point, some of the extracted double oxide was heated on a sheet of pure palladium in air at 900°C, and allowed to furnace-cool over a period of several hours. The X-ray diffraction pattern of the powder showed approximately the same intensity of Rh2O3 and the "hexagonal" oxide as before, but, in addition, a rather faint pattern of another crystalline species made its appearance. This finding again suggests partial transformation of the major (double) oxide to other oxides on cooling from 900°C. Application of the phase rule shows that only one equilibrium oxide (subscale) could have been present at temperature. Vacuum-fusion, oxygen analysis of the extracted subscale showed 7.7 ± 0.7 pct O. Combining this information with that of the X-ray fluorescence analysis suggests the formula PdRhO. This compound should have an oxygen content of 7.07 pct, which is within the range of error of the oxygen analysis. However, until a more careful stoichiometric study is made, it is suggested that the formula be written

Jan 1, 1965

By F. B. Foley

A description of tests made by a committee of the Division of Engineering of the National Research Council to determine whether velocity of impact affects the formation of Neumann bands. FOREWORD Not infrequently, in the case of the failure of a metal structure, such as a bridge, tank, airplane, gun carriage, etc., a doubt arises whether the failure was due, among other causes, to the effect of an overburden or of an explosive maliciously or accidentally exploded in contact with it. As few means of discriminating between the effects of these causes have been known and these means were of a rough qualitative character, it was surprising to find in the record of an inquiry into the failure of a structure, the statement that, by observations on the Neumann bands in the structure, it was possible to determine the speed of breakage in the metal and to distinguish between a fracture caused by an explosion and one caused by an ordinary mechanical strain. Such a criterion, if well proved, was of value to the explosives experts of the Bureau of Mines, the Ordnance Department of the United States Army and the Bureau of Ordnance of the United States Navy, but search showed no record of it in the literature nor did any of the metallurgists and metallographers consulted know of any data on which such a criterion could be based having been assembled and critically studied. However, it was universally held that there was promise in the idea and that there existed unique facilities at the Bureau of Mines Experiment Station at Pittsburgh for the preparation, under definitely known conditions, of material for study by metal-lographers, and that material of value might also be obtained from the proving grounds of the Army and Navy. Therefore, with the approval of the Director of the Bureau of Mines and the Chiefs of Ordnance of the War and Navy Departments, the Chairman of the Division of Engineering of the National Research Council, on April 12, 1919, appointed a Committee on the Investigation of Neumann Bands, which has since been engaged in this study and which, after some slight change in its personnel, consists now of the following: Dr. William Campbell, Advisory Metallurgist, Bureau of Ordnance, Navy Department. F. B. Foley, Metallurgist, Bureau of Mines. S P. Howell, Explosives Engineer, Bureau of Mines. Comdr. O. M. Hustvedt, U. S. N., Bureau of Ordnance, Navy Department. Dr. Charles E. Munroe, Chief Explosives Chemist, Bureau of Mines.

Jan 9, 1922

By J. Gordon Parr, L. P. Srivastava

DUWEZ1 has shown that pure titanium and pure zirconium transform martensitically during rapid cooling at temperatures about 30° and 15°C re spectively below their To temperatures. Holden et al.2 determined M, temperatures of Ti-Cu alloys by a metallographic technique applied to isothermally treated samples. Their results, superposed on the McQuillan3 version of the partial Ti-Cu diagram are shown in Fig. 1. Sources of metals were: Titanium: Iodide bar; Foote Mineral Co. Ltd. Zirconium: Iodide bar; Foote Mineral Co. LM. Copper: Spectrographic Standard; Johnson Matthey and Co. Ltd. Alloys were prepared by levitation melting under argon to the following nominal compositions:* 0.5, Quenching, at rates to about 8000°C per sec, was performed by cooling in a stream of helium (99.999 pct pure) a 3/64 in. cube of material previously heated by a tungsten coil in a system operating at. 10-5 mm Hg. Cooling rates below 200°C per sec w were obtained by controlling the current to the heater coil. The specimen was supported on a 32 gage Pt, Pt-Rh thermocouple attached through a DC amplifier to an Edin magnetic oscillograph (Model 8082) with a maximum chart speed of 250 mm per sec. Transformation temperatures were read off the oscillograph charts at the location of the beginning of the thermal arrest. The same specimen was quenched several times, and all runs were repeated on new samples. Regular calibrations of the oscillograph against a potentiometer were made between quenching experiments. The criterion of martensite formation was the effect of surface rumpling. Previously polished samples that showed a rumpled surface after transformation are assumed to have undergone martens itic transformation: transformations of a diffusion type produce no surface disturbance, Figs. 2 and 3. Electrochemical measurements were made in a cell described elsewhere4 whose electrodes were the martensitic and the diffusion-transformed materials in the following electrolytes:

Jan 1, 1962

By R. R. Goddard

By use of the frequency response method with a radioactive tracer, it was possible to determine fluid dispersion and distribution in a natural consolidated and an unconsolidated medium. Measurements were made in a linear flow system at oleic saturations of 69 per cent in the consolidated medium, and 100 per cent in both media. Dispersion and distribution were obtained by measuring the amplitude attenuation and the phase velocity of sinusoidal waves with a dual monitor apparatus. The gamma ray emissions permitted in situ measurements at any distance along the porous samples. One result of importance was that the effective diffusivity increased as the wave length increased. As a consequence, a dispersion coefficient appropriate for the injection of large slugs might exceed the value measured by use of small slugs. Since flow models based solely on fluid velocity and an effective diffusivity coefficient imply that the diffusivity should be independent of frequency, such representations were not adequate for the data of this study. A comparison was made with a capacitance model of porous media with deadend PVs, but even this model was not completely adequate. By using attenuation and phase velocity data, fluid dispersion can be predicted without postulating a differential equation satisfied by the tracer concentration, thereby eliminating the need of a complicated model to represent dispersion. INTRODUCTION The flow of similar miscible fluids through a porous medium can be fairly adequately described by two parameters: the average fluid velocity and the effective diffusivity.1-3 It has been pointed out recently, however, that significant discrepancies exist between this representation and the experimental data.4-7 An improved agreement can be obtained by introducing additional parameters based on the concept of dead-end pores. The purpose of the present investigation was to find out whether the frequency response method could be used to measure the relevant parameters. The method was used in the following form. A stream of fluid was flowed at a constant rate through a sample of porous material and the concentration of a radioactive tracer in the fluid was varied sinusoidally at a fixed frequency. The effects of flow through a porous medium are a decrease in the amplitude of the concentration wave and an increase in the velocity of the peaks of the waves above the average velocity. Attenuation and phase veIocity of the waves were measured as a function of frequency and fluid velocity. The simple two-parameter model implies that the diffusivity should be independent of frequency. Data reported in this paper show that the diffusivity decreases as the frequency increases. Hence, as shown also by many others, the two-parameter model is not completely adequate. Coats and Smith 5 used two additional parameters in their model: the volume of the dead-end pores and the rate of mass transfer between dead-end pores and the flowing stream. Their capacitance model of a porous medium containing some stagnant fluid, to which transfer occurs by molecular diffusion, did not explain the dispersion results of either the present study or of theirs. Instead, the capacitance effect can be better described as the result of extreme velocity variations within the pores of the medium, with transfer between the velocity zones by convection. EXPERIMENTAL PREPARATION OF POROUS MEDIA Data reported here were obtained with a natural Berea sandstone, and with two packings of 20/25 mesh sand. Pertinent information about these media is listed in Table 1. The sandstone core was first sealed with a non-

Jan 1, 1967

By E. A. Gulbransen, W. S. Wysong, K. Andrew

The reaction of carbon in solid solution in a metal with the surface oxide fim on many metals may be inferred from thermo-dynamic calculations for high vacua and high temperature conditions. Holm has recently shown that oxide films may be removed from ferrous materials by heating in a vacuum at high temperatures and that carbon is the essential element in the reaction. considerable work has been described in the literature on the de-carburization reaction. Several general references may been 2,3,4 However, the nature of the mechanism involved in the decarburization is not well understood. Our interest in this reaction resulted from many attempts to degas and to reduce by pure and dry hydrogen the surface oxides on strips of various types Of chrome-nickel alloys. Some of the early experiments On the behavior Of '3 pct chrome-iron in vacua of the order of 5 X lo' mm and at a temperature Of 600°C have been reported.5 These experi-merits showed a 'low reaction with the residual Oxygen Or water vapor in the system and no reaction with hydrogen. This is in accord with thermodynamic data which would lead to the prediction that it is extremely difficult to maintain a hydrogen atmosphere at 600' C pure enough to reduce Crz03 formed On the surface. The crystal structure of the superficial oxide film formed on 13 pct chrome- iron and Nichrome V has been investigated in the thin film range by Gulbransenr Phelps and Hickman,' and shown to be "203. It Was surprising to us to note that when a specimen of Nichrome V containing approximately 80 pet nicke1 and 20 pet chromium was heated to 850°C in a high vacuum, the specimen lost weight. The rate Of weight loss was very temperature sensitive. A study of this reaction in vacua and in a hydrogen atmosphere is the subject of this communication. Type Reactions Let us consider the various reactions which may occur when a metal is heated in vacua, in a hydrogen atmosphere, or in an oxygen atmosphere. The number and kind of reactions will depend upon the chemical nature of the metal, its alloying constituents and the location of the alloying constituents. The metals used in this study are chrome-nickel alloys of the heater type, They consist essentially of chromium, nickel and iron, small amounts of carbon, silicon and manganese and traces of zirconium, calcium, aluminum and magnesium. The trace elements are added to improve the lifetime and other characteristics of the alloy when used as a heater. Seven of the more important reactions with which we are going to be concerned here are as follows: 1. Metal . (gas) F? metal + gas — degassing of the metal 2. zM(s) + y }i Oi(g) M MIOu(s) -oxidation

Jan 1, 1949

By A. M. Sarem, J. M. Campbell

Molecular refraction is introduced as a new and improved third parameter for prediction of the PVT behavior of hydrocarbon systems. This parameter, characterizing the complex as well as the pure hydrocarbon systems (1) is a direct measure of London dispersion forces which affect the PVT behavior; (2) can be measured directly, accurately and easily for complex as well as pure hydrocarbon systems; (3) varies significantly between the reference substances thus allowing accurate interpolation of PVT properties; and (4) has a fundamentally sound basis. Molal average molecular refraction was used with the pseudocritical mixing rule proposed by Leland and Mueller to predict the molal volume of liquid and vapor for 84 published data points on nC4-nCI0, Cl-nC5, Cl-nC4-nC10 systems in the region of coexisting vapor-liquid and at the critical point. The same technique was applied to predict the densities of liquid hydrocarbon mixtures in the two-phase and single-phase regions near the critical point for seven different systems each having different properties of the heptanes-plus fraction, but all simulating the fluids of either gas-condensate or volatile oil reservoirs. A modification of the Leland-Mueller mixing rule for the determination of pseudocritical properties is also presented which yields more accurate liquid density predictions than the original form when used with the proposed third parameter. INTRODUCTION The PVT behavior of multicomponent systems has received widespread attention in the literature in recent years. A large portion of the reported work has stemmed from attempts to overcome the inherent difficulties encountered when using the standard compressibility-factor chart which shows 2 as a function of reduced temperature T, and and reduced pressure p,. This chart assumes that z, is constant for all systems. The error in this assumption is not pronounced for pipeline-type gases high in methane and low in heavy ends, particularly when contained at moderate pressures. For such gases the error in the calculated z is usually less than 2 to 3 per cent. However, the reliability of this approach becomes somewhat nebulous for gas condensate and volatile oil systems at high pressure. One logical approach has been to recognize the variation of 2,. This idea was first suggested by Meissner and Seferianl and used by Lyderson, Greenkorn and Hougen2 to prepare extensive tables of thermodynamic properties. Other third parameters have been proposed by Stockmeyer, Kihara, Riedel, Lightfoot, Bloomer and Pitzer. These were tested by Satter and Campbel13 for many gas mixtures and it was shown that they were inter-related. All of these third parameters have a common fault — they cannot be directly evaluated for the heptanes-plus fraction. Consequently, one necessary requisite of an improved method for predicting the density of multicomponent hydrocarbon systems, was development of a third parameter that could be evaluated for that fraction. PREVIOUS MULTICOMPONENT DENSITY PREDICTION METHODS Sage and Lacey4 suggested a method of using partial molal volumes for computing the density of hydrocarbon gas mixture for pressures to 3,000 psi. In this technique, they approximate the complex multicomponent gaseous mixtures by a quarternary system of methane, ethane, propane and butane. Sage, Hicks and Lacey5 suggest a method of using partial molal volumes for computing the density of hydrocarbon liquids. The results agree within 3 per cent of the experimental values. However, the composition range is limited to about 10 per cent by weight of methane. Consequently, this correlation does not cover the low-molecular-weight liquid similar to natural gasoline and high-pressure gas condensates.

Jan 1, 1966

By A. J. Hendron, D. U. Deere, F. D. Patton, E. J. Cording

In the design of structures founded in the near-surface rock, a distinction may be made between those problems that are related to the strength of the rock mass, and those that are related primarily to the compressibility of the rock mass. The mining engineer deals almost exclusively with problems involving strength in the design of open-pit slopes and underground openings. The civil engineer is similarly concerned with strength problems in the design of vehicular and water tunnels; underground power plants; cut slopes in rock for highways, canals, and spillways; and in the study of the sliding resistance of the foundations of gravity dams and the abutments of arch dams. Moreover, the civil engineer encounters problems in which the compressibility of the rock becomes the key element in the design. These problems include settlement of heavy structures supported on rock, deformation of the abutments of arch dams, and deflection of pressure tunnel linings. The design problems listed above are still solved largely on the basis of experience and rule-of-thumb. However, recent developments in rock mechanics give promise of providing more realistic approaches to certain aspects of the design. This paper, presents some of the more important recent developments which contribute to an understanding of rock behavior and which aid in design of rock structures. Typically, four steps are involved in the design of a structure, whether it be a machine element, a structural member of a building, or a structure in rock. These steps are listed below:

Jan 1, 1967

By J. S. Vanick

An extremely hard, tough, and strong, white or chilled cast iron has been applied for the past several years to industrial and mining services in which its unusual properties have been confirmed by its ability to deliver in many instances much better performance than plain chilled iron, or other wear-resistant materials. It is being produced regularly by alloying a good base composition of chilled or white cast iron with essentially 4 to 6 per cent of nickel and 1 to 2.5 per cent of chromium. Such a material can attain a hardness exceeding 600 to 750 Brinell as against 380 to 530 for corresponding grades of plain chilled iron. The strength is approximately doubled and the toughness significantly increased. These properties make it especially useful for many applications requiring a high hardness for resistance to wear, abrasion, attrition, deformation; to some extent to high compressive loading and to a lesser but important degree to corrosive action. A wide variety of commercial castings is being successfully produced from this iron, ranging in size from the small grain-grinding plates or burrs through medium-sized castings such as sand pumps up to large, heavy castings such as rolls for metal rolling or cement grinding. The composition of this white cast iron may be roughly bracketed within the range shown in Table 1.

Jan 1, 1933

By Rossiter Raymond

JOHN BIRKINBINE was born Nov. 16, 1844, at Reading, Pa., the eldest son of H. P. M. Birkinbine, widely known as a hydraulic engineer. The family removed subsequently to Philadelphia, where, as a young man he established with his father the office now continued by his sons, after more than 60 years. His education was received at public schools, the Friends' High School in Philadelphia, the Hill School at Pottstown, Pa., and the Polytechnic College of Pennsylvania, where his studies were interrupted in 1863-4 by service in the Union Army, which included participation in the battles at and around Gettysburg. Later, he devoted two years to work in a machine shop; and subsequently he became associated with the late P. L. Weimer, under the firm. name of Weimer & Birkinbine, operating the Weimer Machine Works at Lebanon, Pa. Much of his work was in mining, metallurgy, and blast-furnace construction. As manager for the South Mountain Mining & Iron Co. he carried on experiments with various fuels for iron-ore smelting while maintaining the furnace in constant operation. The carefully recorded results obtained were widely published, and are referred to in text-books by other metallurgists as most complete. From his Philadelphia office he was sent to nearly every State, and to Canada and Mexico, for examinations, reports, constructions or improvements in iron-ore mines, blast furnaces, iron works, water supplies, hydraulic development, irrigation projects, etc., and his engineering knowledge was requisitioned by several European corporations. A number of business trips were made to Mexico, beginning with a visit to the Cerro de Mercado at Durango, before railroads were established in that portion of Mexico, to make a critical examination and report on this "Iron Mountain." Later visits covered other localities and engineering problems, familiarizing him with the major part of the iron industry in Mexico. The late disturbed political conditions in that Republic have retarded the probable enlargement, modernization, and improvement of much of the iron and steel industry of Mexico, upon which he investigated and reported for various capitalists on both continents. One interesting subject included in these reports was a proposed electric furnace, to be operated by energy from water power.

Jan 7, 1915

By Carl A. Allen

Page Introduction................... 367 FactoRs Affecting the Choice of Method......... 367 Review of Stoping Methods.............. 368 Underhand Stoping................ 368 Overhand Stoping................ 370 Longitudinal or Flat-Back Stoping........... 371 Rill-Cut Stoping................. 372 Saw-Tooth Back Stoping.............. 372 Shrinkage Stoping................ 372 Combination Stoping................373 Side Stoping.................. 374* Breast Stoping................. 374 Sublevel Stoping.........,....... 374 Square-Set Stoping................ 376 Filling Methods................. 376 Caving Methods of Mining......... 376 Top Slicing.................. 377 Sublevel Caving................. 379 Block Caving ................. 380 Back Caving into Chutes.............. 381. Costs of Mining Methods.............. 382 Costs of Willing and Blasting. Comparison of Stoping Methods ... 383 Lighting................... 386 Timbering and Handling Ore in Stopes.. A Comparison of Square-Set and Top-Slicing Methods..............386 Tramming.................... 380 Mining oF the Massive Porphyry CoppeR Deposits ....390 Utah Copper and Boston Consolidated Mines.....391 Ray Consolidated Mine.............. 392 Miami Mine.................. 392 Inspiration Mine................ 395 Ohio Copper Mine...........395 Development.................... 398 Appendix..................... 399 Costs of Mining................. 399 Costs of Development............... 406

Jan 1, 1915

By M. C. Young

The Ozark Lead Company operating facilities are located in Reynolds County at the south end of the "New Lead Belt" of southeast Missouri. Development of this wholly owned subsidiary of Kennecott Copper Corporation started in May 1964, with a six foot diameter by 1250 foot deep steel lined shaft. A 20-foot diameter, 1480 foot deep, concrete lined production shaft was collared in March 1968. Production from the facilities began that month and has reached a present average of approximately 6000 tons per day. This paper describes the fully automatic system used to hoist the lead-zinc ore from a depth of 1420 feet to the surface crushing and concentrating facilities, as well as the man and materials hoisting system which allows the lowering of large equipment into the mine. MINING Galena, sphalerite and some copper minerals are found in several mineralized zones of the relatively flat lying dolomite of the "Bonneterre formation". The mineable ore zones vary from 10 feet to 110 feet thick, from 200 feet to 1200 feet wide, and several thousands of feet on strike. Two-boom diesel-hydraulic jumbos equipped with rotary percussion drills are used for both development and production. The jumbos are used principally to open the room and pillar stopes, and a track mounted down hole drill is used to bench in areas where the ore thickness warrants. Explosives used are ANFO, dynamite, and water-jell which are detonated by electric blasting caps. Broken ore (and waste) is hauled by rubber tired transports to chuted transfer raises. Approximately every 500 feet, these raises connect the orebody to the 15 foot by 28 foot train haulage level below. Two twenty ton diesel-hydraulic locomotives haul 160 tons per trip to storage pockets which have a total storage of 1500 tons of material. From these pockets the material is fed over a 6 foot by 20 foot mechanical vibrating feeder which includes one 4 foot by 6 foot grizzly section to a 48 inch by 60 inch jaw crusher. The grizzly and crusher products are transferred horizontally 45 feet on a 48 inch conveyor belt, to one of two 750 ton storage pockets. The material can flow unimpeded into one pocket or be deflected into the second pocket by a movable rock filled hopper. LOADING POCKET The material in each storage pocket is controlled by six lengths of ship anchor chain. The upper end of the 20 foot chain is anchored behind a brow in the pocket, while the lower ends are joined by a header. The lower ends of the chains are raised by two electric powered marine barge winches using 3/4 inch cables. The crusher operator controls the raising and lowering of these chains from a console in the crusher station. The upper and lower travel of the chains is controlled by cams and limit switches on the winch drive. The winches are located within 5 feet of the shaft, and shaft water continually causes problems with the electric components. A malfunction in the upper travel switch will cause the winch to pull the chains into the cable sheave (breaking the cable or sheave), while the lower switch causes the winch to unwind too much rope. Serious consideration is being given to changing the electric motors to pneumatic, since pneumatic motors will eliminate the need of any electrics at the winches. The winches can be "bottomed out" against the sheave without damage to the cable or sheave when raising the chains, and can be allowed to "free wheel" to lower the chains. A surge pocket below the two storage pockets feeds material to two

Jan 1, 1975

By Stanley Herold

A FEW notes on the occurrence and significance of mud volcanoes in Colombia may be of interest at the present time, owing to the renewed activity in geological exploration of, the coastal regions bordering the Caribbean Sea. The best-known volcanoes are found a few miles from the seacoast. One is situated to the south of Puerto Colombia; the second, to the east: of Cartagena near the village of Turbaco; and the third, near the village of Puerto Escondido south of the Sinu River. Others. are reported in more inaccessible localities. Usually they stand 2 1/2 or 3 ft. (0.762 or 0.914 m.) above the surrounding ground at the crater, though several craters from 10 to 20 ft. (3.04 to 6.09 m.,) apart will often build up an extensive mound at low gradient. The shallow mound may cover 1/2 or 3/4 acre (0.2 to 0.3 ha.) with an elevation of 12 or 15 ft. (3.65 or 4.57 m.) at the center. The craters are formed of hardened blue clay; the inside diameters vary from 14 to 24 in. (35.56 to 60.96 cm.). The rim is continuous, except on one side where there is usually a cut 3 or 4 in. deep, thus allowing an overflow. The craters are filled to the rim-cut- with a thick mixture of blue clay mud and water, which is kept in agitation by escaping gas. Fig. 1 shows the bubble in the act of bursting and Fig. 2 the appearance of the surface of the viscous fluid a second or so later. The frequency of the explosions is determined by the weight of the column of fluid in the neck of the volcano, consequently, such explosions are not synchronous in a group of craters. Ordinarily, there are two or three explosions in about 3' minutes. The supply of gas is small but steady and sufficient pressure must accumulate before the bubble can enter the column of fluid. The water is derived from the surface and enters the sedimentary strata not` far distant from the volcano. During long dry seasons, as the supply of water fails the volcano dries and geyser action ceases.

Jan 7, 1919

By R. W. Brown, J. L. Loper

The process of sand erosion has been harnessed to perform a useful function—the directed perforating of oilfield tubular goods and formation rock. In this process the sand is carried by a liquid medium and the resrrlting slurry is forced through a nozzle at an extren~ely high velocity. Upon impingement against casing or formation, the fast-moving sand particles erode a perforalion in the casing followed by cavity formation in the medium behind the casing. The many factors influencing the rate and extent of this penetration are inherently difficult to establish experimentally. Equations describing submerged jet behavior have been applied to these conditions. The following paper develops the equations for predicting the performance of the perforating jet. INTRODUCTION The cutting power of high-velocity sand has been well known in the petroleum industry for many years. Sand carried by a high-velocity gas stream causes severe erosion. This effect has been the cause of numerous production problems in certain areas. It was logical to expect that this phenomenon would one day be adapted to useful industrial applications. Development of mobile, high-pressure, high-horsepower pumping equipment in the last decade has made this possible. The sand erosion process involves pumping a fluid containing abrasive solids through a set of nozzles at a high differential pressure (2,000 to 4,000 psi). The pressure conversion into kinetic energy imparts high velocity to the sand particles which, upon impact with the formation face or casing wall, erode the material in an organized pattern. This paper attempts to establish the effects of the various parameters and to predict the performance and limitations of the process. The following factors will be considered: nozzle differential pressure, perforation size, sand concentration, nozzle stand-off distance and backpressure. In general, this discussion is presented along theoretical lines and is substantiated by field results and data where reliable field data exists. POWER EQUATIONS The penetration rate of a high-velocity hydraulic jet is proportional to the power or energy of the jet at the point in quesion. The power of the submerged jet will decrease with distance (or penetration) into the cavity created by the jet. As the cavity is extended into the formation, the power of the jet diminishes to a value equal to the threshold cutting power of the particular formation which is defiined as the lowest power level at which the formation will be abraded by the jet. Obviously, when this point is reached, no further cutting of the formation can occur. It is assumed that this power level for a particular formation is a function of the hardness of that formation. The following equation can be written for the hydraulic process of formation abrasion.

By W. P. Sykes

Seven years ago, Dr. S. L. Hoytl presented a masterful discussion of the hard metal carbides and cemented tungsten carbide. His lecture summarized most of the data then available in the field; many of the details relating to the production, properties and structure of cemented tungsten carbide had never been previously published, for, in fact, this information was only then being acquired. During the intervening years, the cemented carbides have assumed a place of real importance in the commercial field, with an ever widening variety of applications due to constant improvement in the control of production technique and the unremitting search for new compositions that might better the performance of the alloys in one or another type of service. The most recent summary of production methods, properties and guides for the successful application of the cemented carbides appears in the 1936 edition of the Metals Handbook. Of necessity, much detailed information relating to structures and physical properties is not included in such a summary, and it is with such details that the present discussion is concerned. Steps in Preparation While the past 25 years have contributed a valuable store of working knowledge in the field of powder metallurgy, many of the process controls are derived entirely from experience and are not as yet finally explained by a specific physical or chemical phenomenon. For most of the cemented carbides such difficulties are aggravated by our lack of knowledge not only of the complex alloy systems involved, but also by the possible changes in structure and even in composition which may accompany variations in temperature, heating time, and furnace atmospheres. The principal steps in the preparation of these cemented carbide alloys are fairly well known, but to supply a foundation for discussion these steps are briefly outlined as follows : 1. Formation of the metal carbide in the form of powder by heating a mixture of carbon and the metal powder or oxide for several

Jan 1, 1938

By W. P. Sykes

Seven years ago, Dr. S. L. Hoytl presented a masterful discussion of the hard metal carbides and cemented tungsten carbide. His lecture summarized most of the data then available in the field; many of the details relating to the production, properties and structure of cemented tungsten carbide had never been previously published, for, in fact, this information was only then being acquired. During the intervening years, the cemented carbides have assumed a place of real importance in the commercial field, with an ever widening variety of applications due to constant improvement in the control of production technique and the unremitting search for new compositions that might better the performance of the alloys in one or another type of service. The most recent summary of production methods, properties and guides for the successful application of the cemented carbides appears in the 1936 edition of the Metals Handbook. Of necessity, much detailed information relating to structures and physical properties is not included in such a summary, and it is with such details that the present discussion is concerned. Steps in Preparation While the past 25 years have contributed a valuable store of working knowledge in the field of powder metallurgy, many of the process controls are derived entirely from experience and are not as yet finally explained by a specific physical or chemical phenomenon. For most of the cemented carbides such difficulties are aggravated by our lack of knowledge not only of the complex alloy systems involved, but also by the possible changes in structure and even in composition which may accompany variations in temperature, heating time, and furnace atmospheres. The principal steps in the preparation of these cemented carbide alloys are fairly well known, but to supply a foundation for discussion these steps are briefly outlined as follows : 1. Formation of the metal carbide in the form of powder by heating a mixture of carbon and the metal powder or oxide for several

Jan 1, 1938

By Arthur Lubinski, K. A. Blenkarn

It is explained why the bottom portion of freely suspended tubing in a pumping well buckles and straightens in succession during the pumping cycle. Field evidence of resulting rod-on-tubing wear, excessive polished rod load, and excessive horsepower are given. The possibility that buckling hastens pump wear is strongly suggested. Means for either prevention of buckling or for mini-mizing its effects are explained, their relative merits compared, and field results of their use given. These means are: tension anchors, tail pipe, sucker rod guides, and corrosion inhibitors. Charts and formulas for best use of tension anchors, tail pipe, and guides are given. Use of tension anchors, or compression anchors with a heavy tail pipe, prevents both buckling and breathing, thus improving volumetric efficiency. Without tail pipe, buckling above compression anchors precludes such improvement. INTRODUCTION It is well known that a column must be subjected to some compression in order to buckle; and also that a structural member does not buckle if subjected to a tension. When consideration is given to a tubular column, the question may be asked, "How is the buckling phenomenon affected by inside or outside pressure?' At first, it seemingly should not be affected. However, this is not so. In order to arrive at a correct deduction one should first understand the basic reasons for buckling of a column under loading*. Then he should add to the effect of that loading the effect of pressure. Following this procedure, one may discover quite unexpected phenomena. In some cases, when subjected to more pressure inside than outside, a pipe may buckle under tension. In other cases, a pipe may remain straight, although subjected to a very large compression. In 1950 and 1951 it was explained why the bottom portion of a string of pipe freely suspended in a well does not buckle even when subjected to a large compression due to buoy- ancy.2,3 It was shown that the com-monly used concept of a neutral point, as being a point in the string with neither compression nor tension, is inadequate, and a more relevant definition of the neutral point was introduced. The findings were also generalized to cases of different pressures inside and outside a pipe.3a Later, in a further generalization, allowance was made for variations of stress and pressure with depth.' The findings were applied to the new technique of hydrostatic high pressure testing of lengths of pipe in the mill.5 In 1952 it was observed that previous theoretical findings apply to tubing in pumping wells. The lower part of freely suspended tubing buckles during the upstroke portion of the pumping cycle. Later, it was ascertained that this phenomenon is responsible for wear and malfunctioning of the equipment. Various remedial measures were devised and successful field trials conducted. Only brief mentions on the subject have been published.6,7 In this paper, the phenomenon of tubing buckling is explained, field

Jan 1, 1958

By Gerald Edmunds

CASTINGS of pure metals and many alloys usually have a coarse-grained structure characterized by long columnar grains throughout the main body of the casting. Frequently, the surface exhibits finer, some-times nearly equiaxed grains, and such grains may also compose other parts of the casting. This paper deals primarily with determinations of the grain-orientation textures of the columnar and surface grains of polycrystalline zinc castings. It includes some results upon a cadmium casting and a magnesium casting. A hypothesis is devel-oped to account for the observations on columnar grains and to use as a basis for predicting orientations in other cast metals. A general description of the position of the columnar grains in castings is that their long axes are approximately parallel to the direction of the thermal gradient during crystallization. Thus, in cylindrical castings the columnar grain axes tend to be radial, and in large flat castings where most of the cooling is through one or both of the large mold surfaces they tend to be perpendicular to the mold surfaces. At the edges and corners the direction of heat flow and there-fore the position of the grains is more com-plex. Actually observation shows that even in castings made in flat molds the cooling seems to be somewhat irregular, since columnar grains tend to emanate from certain areas of the cooling surface, indicat-ing that thermal contact was better there than in neighboring areas.

Jan 1, 1940

Jan 1, 1951

By Guillermo Zuloaga

THE iron deposits of the Imataca Range of Venezuela, which occur along the Orinoco River, in the northern border of the Guayana High-lands, have lately attracted attention on account of their economic possibilities. Many deposits occur in this area; some of slight economic importance and others that may rank with the largest masses of high-grade iron ore of the world. The geology and the character of the ores seem to be remarkably similar to those of the large iron deposits of Brazil. In the investigation of the Venezuelan deposits a definite relationship has been found between the mineralization of the large orebodies and igneous intrusions, especially norites and granites. The following paper is the result of a field and laboratory investigation of the ore deposits. The field work was done during the months of February and March of the year 1929, partly in the company of Prof. W. H. Newhouse. The laboratory studies have been made in the Massachusetts Institute of Technology, under the supervision of Profes-sor Lindgren and Professor Newhouse.

Jan 1, 1933

By Robert L. Llewellyn

Preparation of coal begins at the face in underground mines or in the pit with surface mines. Impurities in raw coal can be in the seam itself or in extraneous material taken in mining from the roof or bottom. Raw coal is prepared only to the extent that is necessary to make the product salable. Over 60% of all coal production is processed to some extent in cleaning plants. For underground mines the proportion cleaned is 72% as compared to 42% from surface and 15% from auger mines. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only as necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent and only incidently with mines shipping raw run-of-mine coal crushed to a top size of, usually, 2 to 4 in., with little, if any, other treatment. ECONOMICS OF COAL PREPARATION During the past decade, major changes have occurred affecting the market, profit, and long-rang planning of the coal industry. Mining companies have become "partners" with consumers at many new and some old mines, both for steam and metallurgical coals. Coal properties have become "assigned" tonnages at mutually agreed upon conditions and prices. Lower unit-train tariffs have been instrumental in helping coal markets to compete against oil and atomic energy. Cod prices for power plants are still on a Btu (British thermal unit) basis but with more emphasis on sulfur content. For metallurgical coal, the lower and medium volatile coals are in demand and the price rises, generally, as the volatile percentage is lower. Moisture affects the Btu value of coal almost the same as ash content, but dusty conditions during loading and unloading are no longer accept-

Jan 1, 1973