Search Documents

By C. A. Bruch, W. E. McHugh, R. W. Hockenbury

Commercially pure molybdenum specimens were irradiated in the Materials Testing Reactor for an estimated exposure of 1.9 to 5.9x10 20 thermal nvt. Prior to irradiation, the material was ductile in the tension test; whereas after irradiation, it was brittle. The results of tension tests conducted at various temperatures revealed that the transition temperature for this material had been increased from —30' to +70°C as a result of the radiation exposure. From metallographic studies, it is concluded that the embrittlement is due to submicroscopic changes which raise the flow stress-temperature curve of the material. PRIOR to ten years ago, the bombardment of metals with high speed heavy particles such as protons, deuterons, a particles, and neutrons was primarily of academic interest. These particles existed in extremely small numbers in a few laboratories and only under very special conditions. With the introduction of the nuclear power reactors, these particles are now available in enormous quantities and it has become important from a practical standpoint to learn how well metals withstand severe reactor radiations. The principal radiations of concern in reactors are neutrons and y rays, since the heavier charged particles exist only in limited regions of reactors. Seitz,' in a theoretical approach, has shown that all of these high energy particles, except y rays, have enough energy to knock atoms from lattice sites and that these knocked-on atoms have enough energy to cause additional displacements of neighboring atoms. The result of this process would be a lattice containing many imperfections in the form of interstitial atoms and vacancies. Hence, it would be expected that the properties of metals can be changed by reactor radiations, and such has been found to be the case. Only a limited amount of data have been published in the open literature,2,3 and these data have been for relatively low integrated-neutron-flux exposures. In general, one effect of reactor radiations on the mechanical properties of metals has been to increase strength and decrease ductility. It is now possible to irradiate specimens in the Materials Testing reactor at much higher fluxes and to higher integrated exposures than previously possible.' The data which are being presented here describe the effects of a relatively high exposure on some mechanical properties of molybdenum. Experimental Procedures Material: The molybdenum used in this investigation was obtained from the Climax Molybdenum Co. The two heats from which the material originated were melted under a vacuum of 5 to 30 microns and cast in 7 in. diam water-cooled copper molds. One ingot contained 0.061 pct C and the other 0.066 pct. Both ingots were hot worked by extrusion and rolling into % in. diam rods, after which they were annealed and straightened. The rods were subsequently heated to 1100°C in a hydrogen atmosphere and swaged to ½ in. diam rods at the Research Laboratory of the General Electric Co. The resulting material had an average hardness of 264 VPN, or 99.2 Rb, and had an average of 5000 grains per sq ml in the transverse section, Test Specimens: Substandard-size tensile specimens were prepared according to the specifications shown in Fig. 1. These specimens were used also for hardness measurements. The metallographic specimens were small disks which were polished, etched, and photographed at X1000 prior to irradiation. The field studied was

Jan 1, 1956

By Edwin R. Phelps, Charles W. Porterfield

BACKGROUND OF SURFACE MINING Surface mining refers to the process of removing the material (over- burden) overlying a coal seam and exposing the coal so that it can be loaded out and conveyed by trucks or other methods to the preparation plant or other facility. Surface mining has not always been important in the coal industry. In the early 1900s, almost all of the coal mined in the United States was mined by underground methods. In 1900, about 192 Mt (212 million st) of bituminous coal were mined and less than 1% was mined by surface methods. The development and use of larger equipment has allowed surface mining to gain prominence throughout the years. Table 1 shows the total production of coal by mining method in the United States for ten-year periods since 1920 and indicates the growth of surface-mined coal production. Surface mining will undoubtedly continue to account for a large percentage of the coal production in the US for many years because: 1) The capacity of surface mining excavators has continued to in- crease. Today, mining companies are using shovels (see Fig. 1) which are able to move up to 137.6 m3 (180 cu yd) in each bite and draglines (see Fig. 2) which move up to 168.2 m3 (220 cu yd) in each bucketful. 2) Increasing tonnage from the thick western coal seams is being produced by surface mining methods. 3) Surface mining has normally had lower costs and a better safety record than underground mining. 4) Surface mining normally recovers a much higher percentage of the coal reserve than can be recovered by underground mining. 5) Some coal measures can best be extracted by surface mining

Jan 1, 1981

By Don Blackmar

THE production of non-ferrous secondary metals has become a large and important industry in the United States, and deals with practically every type of manufacturing concern.. Its business is unique in that it generally buys from its customers as well as sells to them, whether they are individuals, cities, corporations, or the United States government. Its operations are of vital importance to the success and prosperity of many of the nation's most important manufacturers; yet there are few industries about which less is generally known by those outside it, whether concerning the magnitude of its operations or the details of its actual technique. The industry itself is to blame for this meager publicity, because its technical men have made few attempts to openly exchange ideas, in spite of the excellent examples set by the iron and-steel or the copper and brass industries. Whether this is due to the ancient shroud of secrecy generally supposed to cover smelting operations, or because its technical men actually felt that the industry was too puny to be interesting, is hard to say. This paper will consider its subject in a 'general way, attempting to show something of the size and importance of the industry, as well as its fitness to do its work well. Attention will be called to the sound economic reasons for the handling of non-ferrous wastes by specialists, and to the often unseen losses of metals and labor which occur when manufacturers reclaim' their own metallic wastes.

Jan 1, 1928

By J. Groyecki, M. Markuszewicz, J. Lassota, A. Zawada

The ratio of stable to unstable inclusions was found to ploy an essential role in the process of sccorldar-y recrystatlizalion in Si-Fe. The analysis of the free energy of inclusions in the range of heat-treatment of individual inclusions to be predicted. The effects MnS. ns inslable inclusions. were investigated. TO secure a high induction, the secondary recryslulliztt-lion associated wilh the texture is necessary. To obtain a low core loss an additional refiuing in the solid state is required. It has been found that sulfur can be more easily removed in racunm than in hydrogen and thai this process was hindered by the prescrzce of INCLUSIONS play an essential role in the development of cube-on-edge texture in Si-Fe. Their function consists in restraining the growth of primary grains up to about 900°C and in passing subsequently into solution at higher temperatures. This process is accompanied by the selective growth of secondary grains with (110)[001] orientation. The general effect of inclusions depends on such factors as the type of impurities, their amount. dispersion and stability, the conditions of diffusion in the space of lattice of metal, and the reactions at the metal/gas interface. In recent years, some of these factors were the subject of a special investigation. A positive influence of Mns, siN,' and vN3 has been established. The quantity of impurities4 and their dispersion5 have been found to be of major importance. Attention was called to the vital importance of diffusion and the conditions under which the impurities are removed from metal., It has also been demonstrated that in Fe-Si alloys by the techniques of powder metallurgy a special opportunity exists to obtain the (110)[001] type texture. 6 The aim of this work was to conduct qualitative investigations on the influence of inclusion stability on the development of cube-on-edge texture in a metal containing approximately 3 pct Si. Experiments were carried out on cast alloys and on those manufactured by powder-metallurgy techniques. The results obtained from these experiments were utilized to explain the phenomena involved and to analyze the relationships between stable and unstable inclusions and the magnetic properties of alloys. EXPERIMENTS AND RESULTS The raw materials used in these experiments were the powder of carbonyl iron with the analysis (in pct) 0.044 C, 0.01 Mn, 0.005 Si, 0.009 P, 0.002 S, traces of Cu, 0.06 Ni, 0.0015 Al, 0.03 Cr, 0.02 Mo, 0.01 Ti, 0.002 Co, traces of Pb, and the powder of silicon containing 94.14 Si, 0.003 S, 0.048 C. The powders were ground and mechanically mixed in 100-g batches. and then pressed at 9 tons per sq cm into 74 by 24 by 8 mm blocks. Sintering was carried out at 1100°C for 12 hr in vacuum (2 x lo-' Tr) or in hydrogen. In this instance the material was heated slowly and subjected to prolonged soaking at 350°, 650°, and 750 2C, respectively, to secure reduction of ferro-oxides. This was checked by making measurements of the dew point, which was found to change from -15" to -35°C after reduction. The compacts after sintering were hot-rolled to 2.4 mm, annealed at 800 C, and finally cold-reduced to 0.35 mm with intermediate annealing at 800°C at a gage of about 0.8 mm. Impurities were added in the powdered form and mixed with iron and silicon powders. Sulfur in the elemental state, electrolytic manganese, and pure aluminum oxide were employed. Besides, to obtain a material with low contents of impurities, especially

Jan 1, 1967

By J. F. Wolff

During the past 4 or 5 years, much has been added to the detailed geologic knowledge of the Mesabi Range. This has not been in the direction of discovery of any new fundamental facts, but of detailed study, subdivision and correlation of different parts of the whole formation and of individual orebodies. Prior to this time, mining engineers in the district were so engaged with the commercial interests of exploring and developing orebodies that close geologic study and subdivision were done in a few instances only. The demand for refinement of work in .this direction has led 'the engineers of the Oliver Iron Mining Co. to do extensive structural subdivision and correlation in all exploration work during the past 4 years. Such work has become a commercial necessity rather than a scientific refinement, and at the present time is being extended to all parts of the Range. In the summer of 1914, the author of this paper wrote a series of articles on the orebodies and special features of the Mesabi Rangc, which was published in the Engineering and Mining Journal, issues of July 17 to Aug. 7,1915. Since that time studies of subdivision of the iron-formation have been extended considerably. The principal feature of this paper is the presentation of the subdivisions of the iron-formation. To this is added a discussion of the relations of the orebodies to the gentle folding and fracturing of the formation, and special features of the Range. The outline will be as follows : I. General geology. 11. Subdivision of Biwabik iron-formation. 111. Relation of orebodies to folding and fracturing of the iron-formation. IV. Special features. Acknowledgnlent is due to W. J. Olcott, President, and John Uno Sebenius, General Mining Engineer, of the Oliver Iron Mining Co., for permission to use the information presented in this paper.

Jan 1, 1917

By L. J. Demer, W. W. Walker

AMONG several variables of the indentation hardness test is the effect of loading time on the measured hardness of a material. The most generally recommended duration of loading is 10sec.1-3 Although this short loading duration is undoubtedly satisfactory for harder metals, it is questionable that it is sufficient for very soft metals,4 or for certain plastics.5 The effect of duration of loading on the measured hardness of ionic crystals is largely unknown, although Onitsche and Mitsches found that the indentor (under a very low load) had not yet reached equilibrium after 60 sec in a variety of ionic crystals. To extend further the data of Onitsche and Mitsche, a systematic study was made of the effect of duration of loading for longer periods, up to 50,000 sec, on the 136 deg Dph of synthetic lithium fluoride. For comparison, less extensive tests were made on synthetic magnesium oxide and copper single crystals. The general procedure used was to indent a cleaved and polished (100) face of a lithium fluoride crystal using a Leitz Durimet microhardness tester. In certain cases, the indentor was so oriented as to align the diagonals of the 136 deg diamond pyramid indentation parallel to a (100) edge. In other cases the diagonal of the indentation was aligned at 45 deg to a (100) edge of the crystal. After indenting, the surface tested was etched in the acid etchant recommended by Gilman and Johnston.' This revealed the position of dislocation lines which intersected the surface tested. At these points of emergence were formed the usual sharp, pyramidal etch pits as shown in Fig. 1. The specific procedure used in studying duration of loading was as follows. The surface of the crystal was indented, and the load was left on the indentor for a predetermined time. This duration of loading was varied systematically from 1 to 50,000 sec. After the desired amount of time had elapsed, the indentor was removed from the crystal and the size of the resulting indentation was determined using a micrometer eyepiece. The surface was then etched to reveal the dislocation etch pit pattern around the indentation. Procedures used for lithium fluoride, magnesium oxide, and copper were similar. Preliminary studies revealed that, although an indentation was enlarged by increasing loading time, no corresponding changes occurred in the surface etch pit pattern. Since no evidence of dislocation movement was observed on the surface, it was assumed that the plastic deformation indicated by the indentor sinking into the surface was a result of dislocation movement inside the crystal. This movement was studied bf making a series of surface indentations in a crystal corresponding to various lengths of time, cleaving the crystal vertically through the indentations, etching the freshly

Jan 1, 1964

By JAMES BRADLEY

THE Spanish mine is in Nevada County, California, 21 miles northeast of Nevada City by road, and 3 miles north of the town of Washington. The mill and surface buildings are on Poorman's Creek at an ele¬vation of 3,000 ft. About 35 men are employed at the property, which is producing 50 tons of ore per day. Electric power, purchased from the Pacific Gas and Electric Co., is brought in from Alleghany, seven miles away. In the early days the mine was operated by F. W. and P. R. Bradley. Between 1883 and 1899 the production was approximately $900,0)0 in gold. The ore treated during; that time yielded an average of 60 cents per ton and was mined and milled at a profit. The surface, oxidized, ore deposit was 30 to 100 ft. wide and was mined by the glory-hole method. The milling-plant at first consisted of a Blake crusher an-1 a small Huntington mill; later three large Huntington mills were added to the plant. In 1893 a new mill was built at a lower adit- It consisted of 10 stamps and four Huntington mills. The gold was secured by amalgamation, the recovery being about 50 per rent.

Jan 1, 1931

By Edwin R. Phelps, Charles W. Porterfield

BACKGROUND OF SURFACE MINING Surface mining refers to the process of removing the material (over- burden) overlying a coal seam and exposing the coal so that it can be loaded out and conveyed by trucks or other methods to the preparation plant or other facility. Surface mining has not always been important in the coal industry. In the early 1900s, almost all of the coal mined in the United States was mined by underground methods. In 1900, about 192 Mt (212 million st) of bituminous coal mere mined and less than 1% was mined by surface methods. The development and use of larger equipment has allowed surface mining to gain prominence throughout the years. Table 1 shows the total production of coal by mining method in the United States for ten-pear periods since 1920 and indicates the growth of surface-mined coal production. Surface mining will undoubtedly continue to account for a large percentage of the coal production in the US for many years because: 1) The capacity of surface mining excavators has continued to increase. Today, mining companies are using shovels (see Fig. 1) which are able to move up to 137.6 m3 (180 cu pd) in each bite and draglines (see Fig. 2) which move up to 168.2 m3 (220 cu pd) in each bucketful. 2) Increasing tonnage from the thick western coal seams is being produced by surface mining methods. 3) Surface mining has normally had lower costs and a better safety record than underground mining. 4) Surface mining normally recovers a much higher percentage of the coal reserve than can recovered by underground mining. 5) Some coal measures call best be extracted by surface mining

Jan 1, 1981

By J. A. Holmes

Venezuela has continued during 1929 to demonstrate that it is destined for many years to come to be one of our most important sources of crude petroleum. The producing fields of the Bolivar Coastal district along the east side of Lake Maracaibo have continued their phenomenal production, and two new fields have reached the near producing stage, while the results of deep test wells have strengthened the predictions and expectations that oil will be found and produced from many other pools and from several different geological formations. The finding of these new oil pools is not going to be easy, because the surface evidences of geological structure are scanty, and the subsurface problems are difficult, but intelligent effort backed by ample resources may be counted upon to overcome these obstacles and lead to a continued increase in the number of producing fields in Venezuela. During 1929 the total production of Venezuela was approximately 135,953,000 bbl., an increase of nearly 30,000,000 bbl., or 28 per cent., as compared with the preceding year. During 1929 oil in steel storage in Venezuela decreased from 13,000,000 to about 11,000,000 barrels. Tables 1, 2 and 3 briefly summarize Venezuelan production by fields and by years, and show the trend of production since its establishment on a commercial basis. Table 1.---Production of Crude Oil in Venezuela by Years, 1917 to 1929 All Figures in Barrels of 42 Gallons Total PRodUction Total PRoduction Year VeneZUela, Bbl. Year Venezuela, Bbl. 1917....................... 227,000 1927.................... 63,181,000 1918....................... 368,000 1928.................... 106,000,000 1919....................... 258,000 1929.................... 135,953,000* 1920..................... 548,000 Grand Total Since Ineep- 1921...................... 1,544,000 tion................... 380,791,000 1922....................... 2,448,000 Increase, 1929 over 1928.. . 29,953,000 1923..................... 4,170,000 Per cent. Increase......... 28.2 1924....................... 9,234,000 Per cent. 1929 Production 1925....................... 20,219,000 of Total............... 35.7 1926....................... 36,641,000 * Includes estimate for closing period of 1929.

Jan 1, 1930

By J. F. Wolff

DURING the past 4 or 5 years, much has been added to the detailed geologic knowledge of the Mesabi Range. This has not been in the direction of discovery of any new fundamental facts, but of detailed study, subdivision and correlation of different parts of the whole formation and of individual orebodies. Prior to this time, mining engineers in the district were so engaged with the commercial interests of exploring and developing orebodies that close geologic study and subdivision was done in only a few instances. The demand for refinements of work in this direction has caused caused extensive structural subdivision and correlation to he done in all exploration work during the past 4 years by the engineers of the Oliver Iron Mining Co. Such work has become a commercial necessity rather than a scientific refinement, and at the present time is being extended to all parts of the Range. In the summer of 1914, the author of this paper wrote a series of articles on the orebodies and special features of the Mesabi Range, which was published in the Engineering and Mining Journal, issues of July 17 to Aug. 7, 1915. Since that time studies of subdivision of the iron-formation have been extended considerably. The principle feature of this paper is the presentation of the subdivisions of the iron-formation. To this is added a discussion of the relations of the orebodies to the gentle folding and fracturing of the formation, and special features of the Range. The outline will he as follows: I. General geology. II. Subdivision of Biwabik iron-formation. III. Relation of orebodies to folding and fracturing of the iron-formation. IV. Special features. Acknowledgment is due to W. J. Olcott, President, and John Uno Sebenius, General Mining Engineer, of the Oliver Iron. Mining Co., for permission to use the information presented in this paper.

Jan 10, 1916

By Roger G. Rowe

In late 1980, Exxon Minerals Company performed rock mechanics testing on oriented 150 mm drill core from their 75Fi tonne massive sulfide deposit near Crandon, Wisconsin. Instrumented samples from depths of 300 meters indicate premining horizontal stresses in a north-south direction (parallel to pillar faces) to average 12,300 kPa, with the perpendicular plane yielding an average stress of 14,630 kPa. Rock strength versus sample size was compared using uniaxial compressive strengths from 47 mm, 95 mm and 150 mm core. Massive sulfide averaged 153,300 kPa, 139,845 kPa and 75,330 kPa respectively, while the hanging wall and foot- wall averaged 92,000 kPa, 76,560 kPa and 57,960 kPa respectively. Point load compressive strengths were calculated using formula suggested by both Hassani et al., 1980 and Broch et al., 1972. Values calculated using the Hassani formula closely resembled pre- existing point load and uniaxial compressive strengths, while values calculated using the Broch formula were 50 percent low.

Jan 1, 1982

By J. B. Darby

In an investigation of various equiatomic alloys of transition elements, Dwightl did not find evidence for the CsC1-type ordered structure in VMn. More recently waterstrat2 has reported the occurrence of this structure in the alloy his sample had been homogenized at 1150°C and subsequently reannealed at 725°C after crushing to powder. The purpose of this note is to confirm the existence of the CsC1-type ordered structure in VMn and to report a lattice parameter. An equiatomic alloy was prepared by arc-melting under an argon atmosphere vanadium and electrolytic manganese having a purity of at least 99.9 pet. The composition was obtained by charging an excess of manganese and monitoring the weight loss until the stoichiometric composition was achieved; the assumption that the loss during melting was due to the vaporization of manganese appears to be a valid one.' The calculated composition of the sample prepared was 49.85 at. pct V and 50.15 at. pct Mn. Specimens taken from the fractured as-cast buttons were wrapped in molybdenum foil and encapsulated in quartz capsules under vacuum; there was no evidence of a reaction between the alloy and foil. The X-ray patterns were obtained using filtered copper or chromium radiation with a Straumanis-type Debye-Scherrer camera having a diameter of 114.6 mm. The CrKa radiation is best suited for detecting the superlattice lines since it overcomes the slight difference in scattering powers of the components by making use of the anomalies in atomic scattering factor which occur when the frequency of the radiation is close to the characteristic absorption frequency of one of the elements.394 A specimen in the as-cast condition, as well as one which had been annealed for 1 week at 900°C and water-quenched, gave a diffraction pattern for the disordered bcc solid solution. However, when samples were homogenized at 900°C for 3 weeks followed by a subsequent anneal at 700°C for 6 to 7 weeks and then water-quenched or furnace-cooled, the (loo), (1111, and (210) Ka superlattice lines were observed in films taken with chromium radiation. An ao = 2.904 * 0.001 was determined by a Nelson-Riley extrapolation from a film taken with CuKa radiation. The author wishes to thank Mr. J. W. Downey and Mr. L. J. Norton for carrying out the experimental portion of this investigation. This work was performed at the Argonne National Laboratory under the auspices of the U.S. Atomic Energy Commission.

Jan 1, 1963

By V. V. J. Sarma

Interpretation of earth resistivity data involves not only obtaining depth to interfaces but also determining the nature of formations from their resistivity characteristics. Moore's method of interpretation envisages obtaining depths to the interfaces alone. A simple method of estimating the true resistivity values of formations by applying Hummel's formula of average resistivities is proposed. The method would increase the interpretative value of Moore's method as originally proposed. For most of the earth resistivity measurements, the four-electrode configuration developed by Wennerl is employed. In principal, the method consists of energizing (Current I) the ground through two outer electrodes and measuring the resultant potential (v) between the two inner electrodes. The configuration is such that the separation (a) between any two successive electrodes is equal. The apparent resistivity (pa) for such a configuration is given by 2p- a (V/I). By increasing the electrode separation (pa vs a) curves are obtained. Ideally, a homogeneous isotropic formation underground has a characteristic resistivity. However, the field conditions do not present such ideal cases. Almost invariably, even in the same geological bed, the physical conditions are widely different at different parts in the bed. It is further shown that the penetration of the current into the ground for a given horizontal electrode separation, a, is roughly down to a depth, equal to a. It is therefore, evident that the apparent resistivity calculated from the field observations is a weighted average of the resistivities of the materials present down to this depth. With some prior knowledge about the relative dispositions of the geological formations and their physical conditions, it would be possible, by resistivity surveys, to obtain characteristic resistivities for these formations. It is, thus, that the apparent resistivity-electrode separation curves enable one to decipher the resis- tivity distribution at various depth levels and therefore the nature of the geological formations present. Both empirical and theoretical methods have been developed for determining resistivity characteristics of the various formations. The theoretical methods proposed by Tagg2 and Roman3 are derived from studies of the potential distribution on the surface due to the presence of layers of widely differing resistivities underground. The more recent methods of Wetzel and McMurry4 and Wetzel and Mooney5 are but extensions of the original Roman method of superposition. These methods suffer from lack of similarity of the actual field conditions with those of assumed conditions in developing the theory. The empirical methods such as the one developed by Gish and rooneY6 depend purely on personal observation and local peculiarities, and are applicable only for those limited areas. Out of the empirical methods, moore's7 cumulative resistivity method is still found to be applicable in several localities of differing conditions. While Reudy in 1945 adduced some theoretical justification for the method (Eve and Keys),8 Muskat9 and Mooney 10 tried to show the lack of theoretical basis for the same. It is, however, observed that the method in practice "forms a valuable means of successfully attacking the apparent resistivity curves which fail to respond to the Gish-Rooney, the Tagg or the Roman logarithmic methods" (Ramachandra Rao). 11 Comparatively good results are also reported by Melbyel2 by employing Moore's method in interpreting the resistivity results obtained for ground water in the city of Gunnison, Colo. MOORE'S METHOD As has already been pointed out, the application of the theoretical methods is time-consuming, laborious and sometimes not applicable for quick and accurate interpretation of the field data. moore7 has developed a quick method for obtaining depths to interfaces by plotting the cumulative sums of resistivities, against the corresponding electrode separations a instead of plotting the usual Pa — a curve. In this process of continuous integration, corrections for small variations in resistivities, arising due to local surface conditions or adjacent layers, are made, while large consistent variations are brought out

Jan 1, 1963

By Jerome F. Kuzmick

Many investigations have been made on the effect of the variables of pressure, sintering temperature and sintering time on the physical and microstructural charactcristics of metal-powder compacts. Severa1 such investigations have indicatcd that pressure is the least important of these three factors in an attempt to secure a dense. strong compact by a simple coltl-pressing and sintering procedure. However, it was felt that a further study of the effect of pressure on pressed and sintered metal powder compacts might prove interesting, for the following reasons: In work done in the past on the effect of pressure, temperature. arid time, the, metal-powder compacts were subjected to long sintering periods, and temperatures right up to the melting point of the metal were applied. It was thought that pressure might exert a more profound effect under short-time simtering and within narrower ranges of temperature. such as normally would be applied in large-scale production of metal-powder parts. 2. It was hoped that something further might be learned of the nature of the bond in pressed and sintered metal-powder compacts. 3. It was thought that interesting infor mation concerning the work-hardening effect of pressure on the crystal structure. of sintered metal-powder compacts would be obtained. Procedure Rectangular bars, 2 by 1/2 by 1/4 in. were molded from the following metal powders: Atomizcd till powder, 325-mesh Atomized aluminum powder, 325-mesh Reduced copper powder, 100-mesh Electrolytic iron powder, 100-mesh Atomized 70-30 brass powder, l00-mesh The, till powder was molded at various pressures up to 40 tolls per sq. in. This was the maximum, because at higher molding pressures there was considerable extrusion of tin into the die wall, jamming the die plungers. The tin specimens were not -in tered, as this phase of the work was- done merely to see how much a very sold metal could be compressed. The aluminum powder was compressed at various pressures up to 50 lons per sq in. Higher pressures could not be used because of extrusion into the die wall The compacts were sintered one hour at 000 in pure dry hydrogen. The copper powder was molded at vari-ous pressures up to 96 tons per sq. in. One set was sintered at 750°C., another at 050 C. for one hour in pure dry hydrogen. The electrolytic iron powder was molded at various pressures up to 00 tons per sq. in. and sintered, one set at Soo°C and one set at 1300°C for one hour in pure dry hydrogen. Extra 325-mesh specimens were also prepared to study the effect of reduced particle size on grain structure. The brass powder was molded at various pressures up to 96 tolls per sq. in. and silltered for one hour. one set at 65o°C. and one set at 800°C, in pure dry hydrogeu.

Jan 1, 1945

By L. Graydon Carpenter, Donald E. Garrett

Probably the largest single tungsten deposit in the U. S. is one that has yet to produce any tungsten; it is not even listed in tables showing U. S. reserves. This deposit is at Searles Lake, Calif., where the brine contains about 70 ppm WO3. Small though the concentration is, the amount of brine in the lake is so great that it is estimated at 170 million lb of WO3 (8.5 million units), equaling the total of all other known reserves in the U. S. This dry lake is located in the basin formed by the Argus and Slate ranges in the northeastern corner of the Mojave Desert (Fig. 1). It consists of a massive salt body some 35 sq miles in extent, varying in thickness from 0 to 120 ft and containing more than 3 billion tons of salt. A central section of about L. G. CARPENTER and D. E. GARRETT are with the Research Dept., American Potash & Chemical Corp., Trona, Calif. TP 47881. Manuscript, Nov. 4, 1958. AlME Trans., Vol. 214, 1959. 8 sq miles is exposed salt; the remaining area is overlain by mud. Except for the exposed sodium chloride (10 to 15 ft thick) the body consists of a very complex and heterogenous mixture of soluble crystals, containing at least eight major phases. It is only about 53 pct solid, the voids being occupied by a dense brine which is the raw material for two chemical companies operating in the valley.

Jan 3, 1959

By W. C. Hagel

Previous inuestigators have repovted unusually low H* and Do values for self-dzf@szon in certazn bcc metals, e.g., chromium nnd y -uvanium. It has been postulated that this is nn experimental crl -tetion for the existpnce of a four -atom ring meclzanzsm, mid there could be. zmpovtant theoretrcal Implicatlons. By utilizing a precise sectioning technique with Cr51 as the tracer, self-dzffi-lsion measurements in large grains of 99.99-pct Cr were extended from 1200° fo 1600"C. A least- squares analysis of the data yields that D 0.280 exp (-73,20U/RT) cm2 sec-'. These AH* and Do unlues are not anomalous; there is little reason to believe that n vacancy mechanism is not opevatiue. Apparent differences at lower temperatures may result from preferential diffusion along short-circuititing paths and/or sample contamination. WITH continued technological effort, chromium and chromium-base alloys should ultimately become useful high-temperature structural materials. Accurate measurements of self-diffusion coefficients in the pure metal are necessary for a quantitative understanding of sintering, grain growth, creep, and other related rate processes. However, two conflicting determinations have been reported.* Using an Since careful diffusion studies normally yield Do values ranging from 0.1 to 10 cm2 sec-l, the Paxton-Gondolf results require independent experimental corroboration before an undue amount of speculation arises to explain the apparent anomaly. As discussed by Nowick6 and clearly shown by Hoffman and Turn-bull7 for self-diffusion in silver, a low AH* and Do can arise from preferential diffusion along grain boundaries or other short-circuiting paths. The most reliable data come from high-temperature measurements where volume effects predominate. Following a precise sectioning technique developed for determining silver diffusion in the intermetallic compound AgMg8 and cation diffusion in the corundum oxide Cr2O3,9 the purpose of this study was to measure true volume diffusion in high-purity, large-grain samples at higher temperatures than considered previously. Another point of interest is the frequent proposal10-12 that chromium undergoes an allotropic transformation between 1375" and 1800°C where the diffusion data might then show a discontinuity. I EXPERIMENTAL 1) Sample Preparation. The highest purity (99.997 pet) Cr currently available is produced by reduction of chromium tri-iodide. Three pounds of the resulting crystal bar were shipped in a sealed container with a complete chemical analysis from the vendor.* In conformity with the procedure used for

Jan 1, 1962

By M. B. Standing, D. L. Katz

Equilibrium data are reported on the composition and densities of coexisting vapor and liquid phases as a function of Pressure and temperature for four hydrocarbon systems prepared from crude oil and natural gas. The data were observed over a range of pressures from 1000 to 8220 Ib. per sq. in. and at temperatures ranging from 35' to 250°F. The compositions of the hydrocarbon systems were such that the critical temperatures of the mixtures were lower than the range of the investigation. Under these conditions, it is shown that the composition of the systems has a marked effect upon both the absolute value of the equilibrium constants and the change of the constants with pressure for the several components comprising the system. From weight-balance considerations, it has been possible to construct the partial phase diagram of a mixture of a 49.9" A.P.I. crude oil and natural gas having a gas-oil ratio of 3660 cu. ft. per barrel. Descriptions of the apparatus used, the analytical procedure, the material used, and the equilibrium measurements are included. A knowledge of the physical behavior of naturally occurring hydrocarbon mixtures is fundamental to the treatment of many problems in the production, transportation and rehing of petroleum. The recent discoveries of pools having formation pressures up to 7500 lb. per sq. in. and higher, and the development of full-scale equipment to operate at pressures of 5000 lb. per sq. in. or more have greatly increased the need for knowledge of the composition, temperature, pressure and density relationships of coexisting vapor and liquid hydrocarbon phases. The following paper presents the results of investigations upon 22 mixtures of natural gas and crude oil of known com~o~itio~ that had been brought to equilibrium under controlled conditions of temperature and pressure. Data are presented upon the densities and compositions of the coexisting vapor and liquid phases for four different systems containing hydrocarbon material having boiling points from minus 2 5S°F. to well over I000 F. The data were observed Over a pressure range from Iooo Ib. per Sq. in to 8220 lb. Per sq. in. and a temperature range from 35' to 2 50°F. The accepted method of computing the physical relationship between two coexisting phases of a hydrocarbon mixture is by use of the "equilibrium constant" K as proposed by Souders, Selheimer, and Brown. definition,

Jan 1, 1944

By M. B. Standing, D. L. Katz

Equilibrium data are reported on the composition and densities of coexisting vapor and liquid phases as a function of Pressure and temperature for four hydrocarbon systems prepared from crude oil and natural gas. The data were observed over a range of pressures from 1000 to 8220 Ib. per sq. in. and at temperatures ranging from 35' to 250°F. The compositions of the hydrocarbon systems were such that the critical temperatures of the mixtures were lower than the range of the investigation. Under these conditions, it is shown that the composition of the systems has a marked effect upon both the absolute value of the equilibrium constants and the change of the constants with pressure for the several components comprising the system. From weight-balance considerations, it has been possible to construct the partial phase diagram of a mixture of a 49.9" A.P.I. crude oil and natural gas having a gas-oil ratio of 3660 cu. ft. per barrel. Descriptions of the apparatus used, the analytical procedure, the material used, and the equilibrium measurements are included. A knowledge of the physical behavior of naturally occurring hydrocarbon mixtures is fundamental to the treatment of many problems in the production, transportation and rehing of petroleum. The recent discoveries of pools having formation pressures up to 7500 lb. per sq. in. and higher, and the development of full-scale equipment to operate at pressures of 5000 lb. per sq. in. or more have greatly increased the need for knowledge of the composition, temperature, pressure and density relationships of coexisting vapor and liquid hydrocarbon phases. The following paper presents the results of investigations upon 22 mixtures of natural gas and crude oil of known com~o~itio~ that had been brought to equilibrium under controlled conditions of temperature and pressure. Data are presented upon the densities and compositions of the coexisting vapor and liquid phases for four different systems containing hydrocarbon material having boiling points from minus 2 5S°F. to well over I000 F. The data were observed Over a pressure range from Iooo Ib. per Sq. in to 8220 lb. Per sq. in. and a temperature range from 35' to 2 50°F. The accepted method of computing the physical relationship between two coexisting phases of a hydrocarbon mixture is by use of the "equilibrium constant" K as proposed by Souders, Selheimer, and Brown. definition,

Jan 1, 1944

By Robert Glass Cleland

IN gathering material for this book, I have made extensive use of the archives of Phelps Dodge, contemporary news- papers, and a wide range of secondary sources. Two manuscripts-one on the history of Phelps Dodge by Arthur Train, Jr., and John L. Lawler, the other a biography of William E. Dodge by Richard Lowitt-have been of the greatest value. I owe a particular debt to the authors whose names I have just mentioned. I have also gathered important information and obtained revealing points of view from conversations with many people. Personal visits to the company's mines and plants added knowledge and understanding that nothing else was able to supply. I am greatly obligated to the officers of the company, especially to Mr. Louis S. Cates, chairman of the board of directors, Mr. Robert G. Page, president, Mr. George R. Drysdale, vice-president of Phelps Dodge Corporation, and Mr. Walter C. Bennett, president of Phelps Dodge Refining Corporation, for their co-operation and assistance. Mr. Wylie Brown, former president of Phelps Dodge Copper Products Corporation, also supplied valuable data and deeply appreciated hospitality. In my visits to the Phelps Dodge properties, company representatives extended every hospitality and placed at

Jan 1, 1952

By Ronald C. Koo

THE effect of grain size on the mechanical properties of the bcc metals has been a subject of intensive theoretical and experimental study.'-l5 Quantitative relationships have been established experimentally between yield stress and grain size and between the ductile-brittle transition temperature and grain size in a number of metals.6"15 Much significance has therefore been attached theoretically to the grain size dependence. In all these experiments, different grain sizes were always achieved by annealing specimens at various temperatures. The implicit assumption was that any change in the dislocation substructure or in the distribution of impurities which might occur simultaneously with the production of various grain sizes had only a negligible effect on the mechanical properties. The validity of this assumption, however, is questionable. transformation in iron-nickel alloys is actually an extraneous phenomenon due to inadvertent compositional changes in the martensite if the heating rate is not sufficiently rapid. This complication can be avoided by up-quenching for the reversal treatment,5 and then the stabilization does not appear. Clearly, the lattice imperfections and strengthening produced by the reverse transformation are not responsible for the marked stabilization which has been observed by other investigators in these alloys. Data will be presented in this note to show that, at least in recrystallized tungsten of commercial purity, the difference in the ductile-brittle transition temperature of specimens annealed at various temperatures is more a result of a variation in the distribution of impurities rather than of the difference in grain size produced by the anneal. Ductile-brittle transition temperatures in tension were determined on powder-metallurgy tungsten specimens recrystallized at various temperatures. Tensile specimens having a gage length of 1.50 in. and gage diam of 0.18 in. were recrystallized at 1450°, 2000°, 2350°, 2550°, 2750°, or 2800" for 30 min in a vacuum furnace at a pressure of 1 x 10"5 mm of Hg and then tested at a constant extension rate of 8 x 10 per sec in an argon atmosphere from 100" to 800". Typical quantitative analyses of impurities are given in the Table. These results show that, within the precision of the analyses, see Table, annealing did not result in any detectable change in the impurity contents of the specimens, nor was there any detectable difference in purity between specimens having large differences in grain size annealed at the same temperatures . The results of the tensile tests yielded three distinct ductile-brittle transition curves approximately 225' apart. As shown in Fig. 1, data of specimens annealed at 1450°C and those of specimens annealed at 2000°C (O) fell on Curve A. Data of specimens annealed at 2350" and 2550°C fell on Curve B, and those of specimens annealed at 2750" and 2800°C fell on Curve C. The decrease in ductility with increase in annealing temperature became so pronounced that one third of the specimens annealed at 2750" and two thirds of the specimens

Jan 1, 1963