Search Documents

By J. P. Heller, H. B. Bradley, A. S. Odeh

A potentiometric model technique is presented for determining the areal sweep efficiency of a five-spot well pattern, at and beyond breakthrough. A sharp interface between displaced and displacing fluids is assumed. Although the prototype svstem is referred to as a waterflood operation, obvious changes in the notation and computations will adapt the results to other displacement processes. The results of the study include the following. 1. Areal sweep efficiencies for a five-spot well pattern, at and beyond breakthrough, for mobility ratios (displacing to displaced fluid) of 4:1, 2:1, 1:1 and 1:4. 2. Extension of potentiometric analysis to the investigation of the areal sweep efficiency beyond breakthrough in a five-spot pattern by the application of conformal mapping and conductive-solid models. 3. The use of layers of conductive fabric in representing mobility ratio changes in potentiometric models. 4. The development of a probe mechanism for probing conductive solids. The results obtained by conductive-cloth models agree with earlier areal sweep efficiencies at breakthrough obtained by Aronofsky and Ramey 1 on the potentiometric analyzer using electrolytic-tank models. Results beyond breakthrough differ from those obtained by the X-Ray Shadowgraph technique. Data from this study show that, for mobility ratios greater than one, water cut rises rapidly as fluid is produced after breakthrough. However, for mobility ratios smaller than one, a large increase in area swept resulted with only a small increase in water cut. INTRODUCTION In calculating reservoir performance of waterflood-ing operations and other fluid-injection programs, it is necesssary to estimate the areal sweep efficiency * before and after injected-fluid breakthrough into production wells. Influence of mobility ratio on oil-production history, before and after breakthrough for a five-spot well pattern, has been studied by X-Ray Shadowgraph techniques 2-5 and by gelatin models.6 In none of these investigations was the transition zone controlled experimentally. Steady-state anaiog techniques assume that a vertical and discrete interface exists between the displacing and displaced phase. Thus, when using a potentiometric analysis, it is assumed that no transition zone exists. To determine the areal sweep efficiency beyond breakthrough for a five-spot well pattern using the potentiometric analyzer, four principal problems had to be resolved. These were the following. 1. The laborious method of representing changes in mobility ratio in electrolytic tanks by means of contoured wooden blocks. 2. Vapcrization of the electrolyte solution during the study causing concentration changes and, thereby, variable conductivity. 3. The scale-limitation problem 7 that is accentuated by abrupt eiectrolyte depth changes. 4. A wellbore geometry problem. EXPERIhlENTAL EQUIPMENT AND PROCEDURES CONDUCTIVE-SOLID MODEL The theory, equipment and procedural techniques of the electrolytic-tank potentiometric model have been treaced excellently by Lee8 and by Muskat.9 By the use of a conductive solid to represent the fluid conductivity of the porous media, the need for contouring wooden blocks to represent mobility ratio was eliminated. It was found that a carbon-black coated fabric, Uskon D-16,** could be employed as a fairly uniform conductive media. This material, when stacked in appropriate layers and pressed together, can be used to represent changes in mo-

By JOHN JANNEY

STABILIZATION of the adjustment of normal consumption to normal production of world commodities is quite different from reducing production until visible surpluses are consumed. The first means restoration and maintenance of prosperity, the second means merely a temporary alleviation of a condition with the prime cause remaining uncorrected. Overproduction of foodstuffs in some sections of the world while millions starve in other sections represents not so much overproduction of foodstuffs as mal-distribution of foodstuffs. The flour mills of Washington and Oregon normally ship quantities of flour to China. Now, the wheat that would make this flour goes East instead of West. Is this overproduction, or is there something wrong that calls for study, analysis and correction? Can the plan used by the ostrich of hiding its head in. the sand get us by this present world tragedy, or must the challenge to solve this problem be met, constructively? Can we not make out of this breakdown in the world's economic system an opportunity? And use it as the stimulus for remedying the basic cause of the trouble and not content ourselves with devising temporary expedients that aim at remedying this or that of the obvious conditions, in themselves not causes at all but rather the evidence of causes, or that are the symptoms of the real trouble.

Jan 1, 1931

By Harlan N. Barton

A commercially available, portable X-ray spectrograph, lightweight and rugged for vehicle or field camp use, was used to determine Ba, Cu, Fe, Mn, Pb, Rb, Sr, and Zn in stream sediment geochemical samples. Investigations showed a relative standard deviation of 1-3%, detection limits of approximately 100 pg/g and significant matrix effects. Coefficients of correlation greater than 0.9 were obtained between portable X-ray and emission and atomic-absorption spectroscopy analyses. A geochemical map of a known mineralized area showed good agreement with maps prepared by other methods of analysis and sample media.

Jan 1, 1983

By W. L. Hill, W. H. Armiger, S. D. Gooch

The physical properties, chemical behavior under thermal treatment, and fertilizer value of fluorine-containing pseudowavellite (hydrous calcium aluminum phosphate) that occurs as phosphate clay admixed with quartz sand in an extensive deposit near Bartow, Fla., were determined by experiments in laboratory, pilot-plant, and greenhouse. When the mineral was heated at 500°C, 80 pct of the phosphorus become citrate soluble. The heated product, however, deteriorates markedly under moist conditions such as obtain in the soil. EXTENSIVE beds of a soft aluminiferous phosphate lie in the Bartow-Pembroke region of Florida. Although the extent of the deposit is unknown, it is thought that the equivalent of at least five million tons of material containing 25 pct P,Os exists on one large mine property alone, and soft phosphates similar in nature are known to occur elsewhere in the state. This aluminum phosphate, unlike fluorapatite, is rendered fairly soluble in neutral ammonium citrate solution merely by heating it at a temperature below 600 °C, a property made the basis of a process patent by the junior author.' The possibility of producing an available form of phosphorus from what has hitherto been a worthless natural phosphate prompted the Bureau of Plant Industry, Soils, and Agricultural Engineering to make a brief study of the Pembroke phos- phate during the war years with a view towards determining the optimal temperature for heat treatment and the reactions involved in the process. The results of this study supplemented by data and information furnished by the junior author are presented in this paper. Description of Natural Phosphate: The phosphate with admixed quartz sand and siliceous matter occurs as a low-grade (8 to 9 pct P2O5) clay-like material that can be beneficiated cheaply by making a water separation of the very fine material from the sand, floating off the fine material, settling the suspension to a thick slurry, and finally de-watering the slurry by vacuum filtration followed by drying. The product dried at 100 °C contains about 16 pct water and 25 pct P2O5, about 1/12 of which is citrate soluble. Partial analyses of representative samples of the crude ore and corresponding concentrate are given in table I. The concentrate is light yellow in color and even after being dried at 100°C sticks very noticeably to laboratory grinding and screening equipment. Under the microscope the ground material is predominantly light brown crystalline aggregates with index of refraction near 1.61. The principal phosphate mineral constituent was identified as pseudo-wavellite with admixed phosphosiderite.2 Pseudo-

Jan 1, 1951

By W. L. Hill, W. H. Armiger, S. D. Gooch

The physical properties, chemical behavior under thermal treatment, and fertilizer value of fluorine-containing pseudowavellite (hydrous calcium aluminum phosphate) that occurs as phosphate clay admixed with quartz sand in an extensive deposit near Bartow, Fla., were determined by experiments in laboratory, pilot-plant, and greenhouse. When the mineral was heated at 500°C, 80 pct of the phosphorus become citrate soluble. The heated product, however, deteriorates markedly under moist conditions such as obtain in the soil. EXTENSIVE beds of a soft aluminiferous phosphate lie in the Bartow-Pembroke region of Florida. Although the extent of the deposit is unknown, it is thought that the equivalent of at least five million tons of material containing 25 pct P,Os exists on one large mine property alone, and soft phosphates similar in nature are known to occur elsewhere in the state. This aluminum phosphate, unlike fluorapatite, is rendered fairly soluble in neutral ammonium citrate solution merely by heating it at a temperature below 600 °C, a property made the basis of a process patent by the junior author.' The possibility of producing an available form of phosphorus from what has hitherto been a worthless natural phosphate prompted the Bureau of Plant Industry, Soils, and Agricultural Engineering to make a brief study of the Pembroke phos- phate during the war years with a view towards determining the optimal temperature for heat treatment and the reactions involved in the process. The results of this study supplemented by data and information furnished by the junior author are presented in this paper. Description of Natural Phosphate: The phosphate with admixed quartz sand and siliceous matter occurs as a low-grade (8 to 9 pct P2O5) clay-like material that can be beneficiated cheaply by making a water separation of the very fine material from the sand, floating off the fine material, settling the suspension to a thick slurry, and finally de-watering the slurry by vacuum filtration followed by drying. The product dried at 100 °C contains about 16 pct water and 25 pct P2O5, about 1/12 of which is citrate soluble. Partial analyses of representative samples of the crude ore and corresponding concentrate are given in table I. The concentrate is light yellow in color and even after being dried at 100°C sticks very noticeably to laboratory grinding and screening equipment. Under the microscope the ground material is predominantly light brown crystalline aggregates with index of refraction near 1.61. The principal phosphate mineral constituent was identified as pseudo-wavellite with admixed phosphosiderite.2 Pseudo-

Jan 1, 1951

By Charles A. Kelliher

In November of 1957, the Aliquippa Works started operation of the third basic oxygen furnace shop in North America. This high speed basic steelmaking method provided a very economical increase in capacity at the Works. The success of these two (2) 81-ton furnaces led to the construction of a second B.O.F. shop, producing heats of 230 tons at J&L's Cleveland Works in 1962. The experience gained operating both shops provided the background for the design of the new steelmaking complex at the Aliquippa Works. This new complex consists of a three (3) furnace shop with two (2) furnaces blowing alternately producing heats ranging from 120 to 207 tons. This variation in heat size is predicated on the requirement that approximately 20% of the shop production will be used to supply steel to a six (6) strand casting machine, producing 4' through 7" billets. The new B.O.F. shop has replaced all other steelmaking units including the #1 Shop, where operations were discontinued in September of 1968. With the advent of the strand casting facilities in September of 1969, many of the standard shop practices had to be changed to compensate for higher tap temperatures, longer handling times, and reduced ladle availability. The subsequent changes in these areas led to the evolution of the strand cast ladle practice which is described in this paper.

Jan 1, 1972

By D. J. Schmatz

DISCUSSION OF RESULTS The qualitative correlation between low-temperature ductility and prior high-temperature creep strain in nickel obtained in this investigation confirms the result obtained on high-purity brass by Chen and Machlin. However, the quantitative effect is much smaller in nickel. Comparison can be made on the basis of a prior high-temperature strain that is a certain percentage of the total high-temperature elongation to rupture. In the research of Chen and machlin, the prior high-temperature strain of 1/2 pct equaled 8.5 pct of the total high-temperature elongation at rupture. For nickel, in our experiments, 8.5 pct of 21.2 pct equals 1.8 pct. For eh = 1.8 pct, the loss in ductility in percent equals x 100 = b.5 pct. That is, for equivalent bo Formation of Beta Manganese-Type Structure in Iron-Aluminum-Manganese Alloys D. J. Schmatz IRON-aluminum alloys have gained much interest in the past few years for use as a base material for elevated-temperature alloys because of their excel- high-temperature strain the loss in low-temperature ductility is 8.5 pct for nickel as compared to 60 pct for pure a, brass. It is also interesting to note the observation that in nickel the low-temperature fractures, even at the most extreme high-temperature pre-strain, were partly trans crystalline and partly intercrystalline. In the case of a brass, these fractures were completely intercrystalline. According to the data on the percent of the grain boundary area that is cracked, at 22 pct high-temperature elongation, about 12.5 pct of the grain boundary area does not carry load. Thus, the inter-crack areas are carrying a stress that is about 11 pct higher than the nominal stress. A simple model predicts that the overall elongation, which is primarily the elongation in the bulk of the specimen, will correspond to the nominal stress when the stress in the intercrack area equals the tensile strength. Quantitatively this model predicts the equation The form of this equation will agree with that found if the strain-hardening exponent, n, equals unity. Actually this model is too gross an approximation to yield good quantitative results. The question naturally arises as to whether in ordinary hot-working, such as hot-rolling, intercrys-talline cracks are introduced that affect the low-temperature properties. It appears that the answer is that such a possibility cannot be overlooked, if the hot-working induces tensile stresses at temperatures above the equicohesive temperature and if the material tends to be notch sensitive at low temperature. ACKNOWLEDGMENT This research was supported by the Aeronautical Research Laboratory, Directorate of Research, Wright Air Development Center, United States Air Force. REFERENCES lC. Zener: Fracturing of Metals, 1948, Cleveland, ASM. 'H. C. Chang and N. J. Grant: Mechanism of Intercrystalline Fracture. AIME Trans., 1956, voL 8, p. 544; lownal of Metals, May, 1956. 'E. S. Machlin. CreepRupt ure by Vacancy Condensation, AIME Trans., 1956, vol. 8, p. 106; lownd of Metals, February, 1956 'C. Chen and E. S. Machlin: On a Mechanism of High-Temper at ure Inter-crystalline Cracking, lownd of Metals, July. 1957. p. 829. Alloys lent oxidation resistance. Binary alloys of aluminum in iron are ferritic and consequently have poor hot strength. Alloys of iron-aluminum-manganese were made in an attempt to produce an austenitic alloy containing sufficient aluminum to retain the oxidation resistance of binary alloys of iron-alumi-

Jan 1, 1960

By Harvey Cline, Donald P. Ferriss

THE violent outgassing of commercial tungsten and other refractory metals when melted in an electron beam zone refining apparatus1"3 is dealt with experimentally by one or both of two approaches. One is to provide a suitable emission current control1,2 the other is to purify the metal in the solid state before melting.4 The first of these is usually sufficient, but the authors chose also to investigate the source of the troublesome gases and to devise means of solid-state purification. Some further insights into the use of tungsten as a structural material at temperatures near its melting point were also revealed in the course of the work. One may speculate on the causes of gas formation in tungsten at high temperature by inferences from the literature and an examination of the impurities in commercial wire. Davenport5 observed microporosity in both tungsten and molybdenum filaments heated to several hundred degrees below their melting points. Studying the function of oxygen in molybdenum welds, Perry, Spacil, and wulff8 attributed similar porosity to the disproportionation of Moo2 to molybdenum metal and Moo3. Tungsten dioxide also disproportionates7 above 2000oC to yield WO3 vapor at considerable pressure. Commercial tungsten contains some 5 to 20 wt ppm O and a similar concentration of carbon depending on the details and precautions of processing. Therefore, evolution of CO is also a strong possibility as a source of gas at high temperatures. Furthermore, even for activities in the order of 0.01, it may be calculated that the pressure of CO at 3000°C would be over 4000 psi, which is in excess of the tensile strength of tungsten at this temperature.9,10 Powder metallurgy tungsten contains some 0.02 pet Fe and 0.002 to 0.005 pet of the elements Ni, Si, Al, Ca, Mn, Mg, and Mo; at temperatures over 2800°c, therefore, these elements will exhibit appreciable vapor pressure, though small compared to that of WO3 and CO. Some of these impurities may react to form high-pressure monoxides such as SiO and A10. Finally, dissolved and occluded nitrogen is an ever-present source of high-pressure gas. Commercial Type 218, General Electric filament wires, 0.025 in. diam, were heated by resistance in 10 -4 mm of Hg and in argon or hydrogen at pressures from 50 µ to atmospheric. For temperature determinations in vacuo, the Jones - Langmuir8 current-temperature relationship was employed. For gaseous atmospheres, the burn-out temperature was assumed to be the same as in vacuo so that a small, constant correction could be made for temperatures below burn-out conditions (i.e., local heating to failure). Several dozen experiments may be summarized by pointing out some structural observations. At 3050oC in 1 atm of A, porosity is very evident after 30 min, as shown in Fig. 1. For the section in Fig. 2, failure occurred 200°C below the melting point and many voids have grown in the grain bound-

Jan 1, 1962

By Robert W. Fullerton, Donald T. King

INTRODUCTION AND THEORY by Robert W. Fullerton In coal preparation plants, as in any industrial operation where raw materials are handled, nuisance problems arising from the generation of dust are inevitable. Devices for the control or collection of dust are there- fore essential components of the plant process equipment. The general term "aerosol" is applied to small particles suspended in a gaseous medium, usually air, whose velocity under the force of gravity is small enough that the particles remain suspended for a reasonable length of time. Aerosols can be classified as dust, smokes, fumes, mists or fogs. Dust includes particles originally formed by pulverization of materials by such processes as crushing, grinding, drilling, blasting and abrasion. Smoke includes particles formed from the burning of organic materials. Fumes are particles formed by processes such as condensation and sublimation, usually at high temperatures. Mists or fogs are particles formed by the condensation of water or other vapors on some nuclei. The size of aerosol particles is generally designated in units of microns, there being 1000 microns to a millimeter and 25,400 microns to an inch. Particles of about 10 microns or above are visible to the naked eye. Table 14-1 shows size characteristics of the general classifications of particles discussed above and includes typical examples of particles commonly en- countered. Table 14-1 also shows the relationship between micron size and standard screen mesh sizes. Smoke and fume are usually in the range of 0.01 to one micron, dusts are in the range of one to 400 microns, mists are in the range of 0.1 to 100 microns, and fogs are in the range of one to 100 microns. For purposes of dust control, particles greater than 10 or 20 microns in size are considered large, particles one to 10 microns are considered fine and particles below one micron are ultrafine. Sources of Dust Because coal is relatively friable, the mining and subsequent handling operations break part of the coal into dust that can be readily carried by currents of air. In a coal preparation plant mechanical handling operations such as unloading, transferring from one belt to another, screening, cleaning, and crushing in a dry state result in the generation and release of varying amounts of additional dust. The dust problem, of course, is much less serious in plants employing entirely wet processing. In addition to dust from handling operations, thermal drying of the fine coal product frequently presents another dust collection problem. Most coal driers are

Jan 1, 1968

By George J. Young

(San Francisco meeting, October, 1911.) THE nature of slimes handled in the treatment of gold- and silver-ores has been discussed in technical literature to a considerable extent. The subject of slime-filtration from the practical worker's stand-point has also received much comment, and scattered through the literature of the subject are descriptions of many slime-filtration installations. Articles of this nature serve a valuable purpose and assist materially in the design of new and the improvement of old plants. The subject of the physics of slime-filtration has been touched upon to only a slight extent. The underlying principles are worthy of more intensive study and experimentation than they have received, and the main purpose of this paper is to present the results of such study and experimental work as will serve to make clear in part at least many of the principles which control the filtration of slime. Nature of Slime. Much has bean written concerning an accurate definition of the term ? slime," but no comprehensive definition seems to be generally accepted. The reason for this is clear. A slime consists of at least three different substances, each, when separated, possessing distinctly different physical and to a certain extent chemical properties. These substances are extremely fine sand, a colloidal material which may be and generally is in a coagulated condition, and a colloidal material which is in a non-coagulated condition. Suspending a slime in a relatively large volume of water by shaking and allowing sedimentation to take place, results in the fine sand settling out with comparative rapidity, followed by the coagulated material, which settles much more slowly and finally a certain portion remains

Nov 1, 1911

By E. P. Klier

THE work of Klier and Lyman1 on the bainite reaction has led to the full description of this reaction for medium-carbon low-alloy steels. Certain experimental data reported by Klier and Lyman appear, however, to be improbable of obtaining in very high-carbon steels. The study herein reported consists of an analysis of the transformation characteristics of a 3 per cent chromium, 1 per cent carbon steel by means of X-ray and metallographic methods. From the results obtained it is concluded that the bainite reaction in this steel is more complicated than that reported by Klier and Lyman for the low-carbon low-alloy steels. However, the mechanism of bainite formation in this steel appears to be essentially the same as proposed for the low-carbon low-alloy steels with the modification that the first volumes to transform are carbon-rich rather than carbon-poor. EXPERIMENTAL PROCEDURE The analysis of the steel studied was: Cr, 2.89; C, 1.02; Mn, 0.33; Si, 0.35; S, 0.012; P, 0.020. The stock was received from the Carpenter Steel Co. in rolled bars. Specimen Preparation Specimens were austenitized at 1200°C. (2192°F.) for 25 min. in purified nitrogen. The resultant A.S.T.M. austenite grain size was 0-1. Isothermal transformation was allowed by quenching the specimens into liquid metal baths controlled to ±5°C. at 540°C. (1004°°F.) and above, and to ±2°C. at 490°C. (914°°F.) and below. Following the desired degree of transformation all specimens were water quenched. Metallographic Examination Specimens 1/4 in. round by 1/4 in. were used for metallographic examination. Etchants used were Vilella's reagent (1 gram picric acid, 10 ml. hydrochloric acid to make l00 ml. ethyl alcohol solution) and alkaline sodium picrate (electrolytic). Vilella's reagent was effective in revealing all microconstituents, while the alkaline sodium picrate developed the carbon-rich structures or carbides only. X-ray Examination Two X-ray techniques were used-the Debye-Scherrer method and a back-reflection method. The small specimens necessary for the Debye-Scherrer method were austenitized and then allowed to transform, or were cut from the larger metallographic specimens. The metallographic specimens were used for the back-reflection X-ray analysis. When it was desirable to determine the structure of the carbide present, sliver specimens were electrolytically etched to develop a carbide coating, then were exposed in the cameras. This technique was frequently necessary to allow positive identification of the carbide.

Jan 1, 1945

In the special number of the magazine Ocl und Kohle (Oct. 22, 1940) dedicated to the petroleum industry of southeastern Europe, there appeared several articles relating to Yugos1avia.t In the first article the author calls attention to the fact that there are two fields in Yugoslavia that have been explored and exploited by more than 100 wells at variable depths during the last 50 years. These are on the Island of Mura, at the confluence of the Mura and the Drave. Additional exploration drilling in various other parts of the country has been without result, but certain ones of these explorations have revealed the existence of gas horizons that have some value, which are being used for industrial purposes. Table I shows the production of oil and gas between the years 1900 and 1939. TaBle —Production of Oil ad Gas in Yugoslavia . n,i Natural Natural Years oil Years Gas, Cu. Years Gas, Cu. Meters Meters T900-1929 10,000 1923 507,000 1934 1,388,000 1930 277 1924 567,000 1935 1,401,000 1931 202 I92S 691,000 I936 1,483,000 t932 289 19261 1.472,000 1937 1,841,000 1933 629 1927! 1,732,000 193s 2,431,000 1934 324 1928 2,515,000 1939 2,628,000 1935 260 1929 4,700,000 1936 137 I93O 5.345,200 1937 463 1931 6,376,153 1938 1,091 1932 1,661,737 1939 1,114 1933 959,574 The number of wells drilled from 1884 to the present time was in the neighborhood of zoo and the total footage drilled was 65,000 m. up to July I940 They may be divided roughly as follows: 12 wells in the region produce natural gas; 134 wells in the two old fields of the Island of Mura and about zo wells for the exploration of the zone of the Flysch, in Bosnia. The depths of 50 of these wells was roo to 200 m.; the depths of 50 wells oil the Island of Mura ran from zoo to 500 m.; of 2 ; wells, 500 to I000 m.; of ro wells from rooo to 2000 meters. The deepest well drilling in Yugoslavia has reached 2000 in. In the Valley of Morave, in the region of Selnica, I00 km. south of Nish, there have been discovered asphalt-bearing limestones, which contain about 15 per cent asphalt and are associated with bituminous clays. Later, at Paclenica, important deposits of natural gas were found. A zone rich in gas and oil seepages runs through Pracec, Miklenska, Bujavica, etc. The author studied these regions from the point of view of stratigraphy and tectonics. The anticlines and gas-bearing domes are concentrated in two zones: the region of the Drave (Island of Mura) and the region of the Save, southeast of zagreb, which contains the gas field in exploitation in the region of Bujavica. A full description of the productive region of the Island of Mura has been given by Egon Bohm, a geologist, in the second article mentioned. This includes a history of the exploration and exploitation that took place under Hungarian rule in this region. The most important exploration was effected between 1884 and 1885 by Stavenov and Stinger, of Vienna. In 1927 work was done in the same region by Anton Raky, a well-known explorer who makes work of this kind his specialty.

Jan 1, 1941

In the special number of the magazine Ocl und Kohle (Oct. 22, 1940) dedicated to the petroleum industry of southeastern Europe, there appeared several articles relating to Yugos1avia.t In the first article the author calls attention to the fact that there are two fields in Yugoslavia that have been explored and exploited by more than 100 wells at variable depths during the last 50 years. These are on the Island of Mura, at the confluence of the Mura and the Drave. Additional exploration drilling in various other parts of the country has been without result, but certain ones of these explorations have revealed the existence of gas horizons that have some value, which are being used for industrial purposes. Table I shows the production of oil and gas between the years 1900 and 1939. TaBle —Production of Oil ad Gas in Yugoslavia . n,i Natural Natural Years oil Years Gas, Cu. Years Gas, Cu. Meters Meters T900-1929 10,000 1923 507,000 1934 1,388,000 1930 277 1924 567,000 1935 1,401,000 1931 202 I92S 691,000 I936 1,483,000 t932 289 19261 1.472,000 1937 1,841,000 1933 629 1927! 1,732,000 193s 2,431,000 1934 324 1928 2,515,000 1939 2,628,000 1935 260 1929 4,700,000 1936 137 I93O 5.345,200 1937 463 1931 6,376,153 1938 1,091 1932 1,661,737 1939 1,114 1933 959,574 The number of wells drilled from 1884 to the present time was in the neighborhood of zoo and the total footage drilled was 65,000 m. up to July I940 They may be divided roughly as follows: 12 wells in the region produce natural gas; 134 wells in the two old fields of the Island of Mura and about zo wells for the exploration of the zone of the Flysch, in Bosnia. The depths of 50 of these wells was roo to 200 m.; the depths of 50 wells oil the Island of Mura ran from zoo to 500 m.; of 2 ; wells, 500 to I000 m.; of ro wells from rooo to 2000 meters. The deepest well drilling in Yugoslavia has reached 2000 in. In the Valley of Morave, in the region of Selnica, I00 km. south of Nish, there have been discovered asphalt-bearing limestones, which contain about 15 per cent asphalt and are associated with bituminous clays. Later, at Paclenica, important deposits of natural gas were found. A zone rich in gas and oil seepages runs through Pracec, Miklenska, Bujavica, etc. The author studied these regions from the point of view of stratigraphy and tectonics. The anticlines and gas-bearing domes are concentrated in two zones: the region of the Drave (Island of Mura) and the region of the Save, southeast of zagreb, which contains the gas field in exploitation in the region of Bujavica. A full description of the productive region of the Island of Mura has been given by Egon Bohm, a geologist, in the second article mentioned. This includes a history of the exploration and exploitation that took place under Hungarian rule in this region. The most important exploration was effected between 1884 and 1885 by Stavenov and Stinger, of Vienna. In 1927 work was done in the same region by Anton Raky, a well-known explorer who makes work of this kind his specialty.

Jan 1, 1941

INTRODUCTION Trade financing is a particularly important component of short-term financing for a minerals company since errors, extra costs, or payment delays/defaults can easily wipe out the profit margin on a particular shipment or can cause problems when arranging purchases of e.g. reagents. It is required to make any minerals operation function and does not have to be cross-border to require proper management. Sources of working capital are as follows: 1. Extended credit terms from suppliers 2. Inventory loans from banks, finance companies 3. Accounts receivable financing or factoring 4. Credit lines or overdraft facilities from banks. TRADE CREDITS These are provided under the familiar terms "net 10 days" or payment due by the "10th day of the following month." Thirty days for payment is usual but longer periods can be negotiated with regular suppliers. Shipment may be made on open account with specified periods for settlement. In the mining industry, a custom smelter gains trade credit by paying for concentrates three months after the month of shipment. INVENTORY LOANS Various forms of inventory finance are provided via "floor-plan" or warehouse financing. A set percentage, usually 60%-80%, of a good-quality, readily saleable inventory item (e.g. bullion, concentrates, ingots) will be provided by a bank or finance company which will usually have security over these products and has a right to inspect the goods from time to time. Legal security will he achieved by warehouse receipts, floating liens, chattel mortgages, trust receipts, or through collateral management service companies. The latter certify control over stock or distribution outlets and often carry insurance against fraud. Costs range around 1.5% - 2.0% p.a. or more plus some fees to cover out-of-pockets or other costs. ACCOUNTS RECEIVABLES Accounts receivable financing is based on the company's generation of satisfactory receivables which are continuously assigned to a bank or finance company ("factoring"). Because of the risks in being able to collect receivables, such as payments to a smelter for its blister copper shipments to a refinery, this form of financing costs as much as 3% - 5% of the debt amount purchased plus an additional charge for processing paperwork. Receivables can be purchased with or without recourse and on a notification or non-notification basis to the client's customer to, respectively, pay the invoice directly to the bank or not. LETTERS OF CREDIT Letters of Credit ("L/C's") are a common feature of international trade finance whereby a bank, at the request of the buyer, issues a written undertaking to an exporter to pay a specified sum of money within a set time on presentation of previously specified documents. This undertaking means that the exporter is no longer relying on the credit standing and integrity of the foreign importer. A dispute about shipment does not otherwise affect the obligation to pay upon presentation of a "clean" set of documents. These documents include the hill of lading and other documentation, often on standard "form" bases. There are a number of conventions and techniques in L/C's such as irrevocable/revocable L/C's, time L/C's, confirmation/advising L/C's and transferable L/C's. These are tools to adjust for the varying risks that the importer will not pay. Other routes where one is comfortable with an importer include documentary sight hills (D/P hill), documentary term bills (D/A bill), and, of course, open account.

Jan 1, 1985

By R. H. Hadfield

Professor ArnolD, of the Sheffield Technical School, who has done so much excellent work in metallurgical research, recently produced, with the aid of aluminum, a sound ingot and bar from the purest known Swedish brand containing 99.8 per cent. of pure iron. Table 1. shows the physical quantities of this metal. TABLE I.— Tests of a Sample of Almost Pure Iron Prepared by Professor Arnold from D. v Ewedish Bar, Containing Before Fusion 0.04 Per Cent. of Carbon. I. II.+ III. Series mark,.. 136 1.371F ...... C, 0.07 0.07 Si, 0.04 0.04 8, 0.02 0.03 ...... Analysis, per cent,. .. P, 0.02 0.015 ...... Mn, 0.06 0.07 Al, 003 ............ Fe, 99.76 99.81 ...... Specific gravity,........... 7.863 ...... Original diameter, inches,. .. 0.564 0.798 0.798 Original area, square inches,. . 0.25 0.50 0.50 Limit of elasticity, tons per square inch,...... 18. 3.8 Breaking-load, tons per square inch,. 21. 23. 14.75 Total elongation, per cent., measured on 2 in.,...... 50. 49.25 61. Total reduction of area, per cent.,. 80. 69.60 61.20 Extension at permanent set, per cent.,...... 0.007 ...... silky and Appearance of fracture,. .. . silky i granular in parts.

Jan 1, 1894

By Frederick Jr. Prime

THE first catalogue of Geological Reports of the United States was prepared by Prof. O. C. Marsh, and published in the American Journal of Science and Arts for 1867, vol. xliii, second series. Since then the list has more than doubled, and it was thought that the publication of a new catalogue, brought down to date, would be useful to many of the members of the Institute of Mining Engineers. The compiler will be most thankful to have any omissions or inaccuracies in the list sent to him, to be published as a supplement in the next volume of the Transactions. Especially to have the correct title, number of pages, plates, and maps of any volume on the list to which an * is prefixed, as he has been unable to personally consult such works. A preliminary list was issued last February, which has been almost doubled by the kindness of many friends. The writer desires more especially to express the obligations he is under to the following gentlemen The Chief of Engineers, U. S. A.; Principal Dawson, Mr. G. M. Dawson, Drs. B. J. Harrington and T. Sterry Hunt, of Montreal; Mr. H. Engelmann, of La Salle, Ill.; Dr. F. V. Hayden and Prof. J. W. Powell, U. S. Department of the Interior ; Prof. E. W. Hilgard, University of California; Prof. Henry Y. Hind, Windsor, N. S.; Prof. C. H. Hitchcock, of Dartmouth College; Mr. Henry A. Holmes, State Librarian, Albany; Maj. Jed. Hotchkiss, Staunton, Va. ; Prof. W. C. Kerr, Raleigh, N. C.; Dr. J. S. Newberry, of Columbia College ; Prof. W. H. Pettee, of the University of Michigan ; Dr. Samuel H. Scudder, Prof. N. S. Shaler, and Prof. J. D. Whitney, of Harvard College ; Mr. Sanderson Smith and Prof. J. J. Stevenson, of New York ; Mr. Addison Van Name, of Yale College, and Lieut. Geo. M. Wheeler, U. S. Engineers. PHILADELPHIA, 907 Walnut Street, October 1st, 1879.

Jan 1, 1879

[NORTH AMERICA UNITED STATES ALABAMA AUBURN Sturm & O'Brien, Consult. Engrs. °Sturm, Rolland G. BESSEMER Granger, W. C. BIRMINGHAM Air Reduction Sales Crockett, John M. Amer. Cast Iron Pipe Co. Carter, Sam F., Jr. Donoho, C. K. Anderson Elec. Corp. Davis, Moss V. J. B. Clow & Sons Neptune, Maurice D. Connors Steel Div. °Sandelin, Robert W. Hayes Aircraft Corp. Ricketts, W. E., Jr. Willhelm, A. Clyde, Jr. McWaine Cast Iron King, O. H. Worthington, B. W. Shook & Fletcher Sup. Co. Gearhart, Thomas A. Southern Res. Inst. Dismukes, Edward B., Wheelahan, Edmund J. Thomas Foys Miller, Ralph M. Union Carbide Metals, Co. Brandler, Edgar A. U. S. Pipe & Fdry. Co. Clay, Donald H. Unaffiliated Berg, H. A. Caldwell, H. A. Gilmer, H. U. Harris, Thomas H. Templeton, J. B.]

Jan 1, 1961

By S. Yukawa, M. J. Sinnott

A high resolution autoradiographic study of the diffusion of a nickel isotope (NP3) into copper in the temperature range of 650° to 925°C, with particular emphasis on grain boundary diffusion, has been made. The extent of grain boundary diffusion is a function of the grain boundary angle and the diffusion temperature. The ratios of the grain boundary diffusion coefficient to the lattice diffusion coefficient ranges from 104 to 105. The activation energy for grain boundary diffusion decreases with increasing grain boundary angle. STUDIES and reviews&apos;-8 of metallic diffusion have indicated that grain boundary diffusion is a common phenomenon but quantitative studies of the many variables involved are not numerous. The present work was concerned with determining the influence of the crystallographic orientation of the grain boundaries and the temperature on the extent of boundary diffusion of nickel into copper. The study involved essentially three steps: 1—the production of grain boundaries of known crystallographic orientation, 2—the determination of the extent of diffusion into the boundaries, and 3—the analysis of the resulting data in terms of the usual diffusion concepts. The grain boundaries investigated approximated the simple tilt variety having l° of freedom. They were produced by controlling the solidification from a melt of Cuprovac (a high purity vacuum-melted copper obtained from Vacuum Metals Corp.) of a pair of seed crystals so that the bicrystals of copper produced had a common <100> axis. By rotating one seed crystal relative to the other, a simple tilt boundary was produced. The angle of rotation between the two crystals is the grain boundary angle 8, or what is sometimes termed the misfit angle. In all, some 16 boundaries ranging from 2" to 72" in 5" to 10" steps were investigated. The crystallographic orientations were measured with the use of both X-ray and optical goniometric techniques. The <100> axes in the crystals were found to be parallel within 2" to 3" with the exception of one crystal (8 = 12") in which the axes were 6" from being parallel. All bicrystals showed evidences of sub-grain structures. Laue analyses showed that these subgrains differed in orientation up to a maximum of 2". Because of these variations, and some curvature in the boundaries, the grain boundary angles listed are actually average values and deviate from the 1 o of freedom boundaries. The stripping film technique of high resolution autoradiography was used to detect the diffusion of the nickel isotope into the grain boundaries of the bicrystals of copper. Kodak experimental permeable stripping film with an emulsion layer 5 u thick

Jan 1, 1956

By Frank C. Aplleyard

The two calcium sulfate minerals-gypsum and anhydrite-occur in many parts of the world, and gypsum has long been of economic importance in the family of industrial minerals. Gypsum, the dihydrate form of calcium sulfate (CaSO4•2H2O) and anhydrite, the anhydrous form (CaSO4) are frequently found in close association, and it is seldom that a calcium sulfate deposit will consist exclusively of one mineral or the other. Although known gypsum deposits are extensive, anhydrite makes up the largest part of total calcium sulfate reserves. However, it has very minor economic use, and most of the following discussion will be devoted to gypsum. Calcium sulfate is one of the principal constituents of evaporite deposits, and when pure, has the following composition: [Sulfur Combined Lime Trioxide Water (CaO) (SO,) (H2O) Gypsum 32.6% 46.5% 20.9% Anhydrite 41.2% 58.8% -] Deposits of pure gypsum or of pure anhydrite which are large enough to be considered commercial have never been found because of both the metastable relationship between the two minerals, and the presence of impurities such as calcium or magnesium carbonates, chlorides, other sulfate minerals, clay minerals, or silica. As a result most mine production of gypsum will range between 85 and 95% pure. Often it is used as mined, although in certain cases, one or more forms of mineral beneficiation are employed to upgrade the product. End Uses The largest use for gypsum is based upon the unique property which calcium sulfate has of readily giving up, or taking on, water of crystallization. With the application of a moderate amount of heat in a process known as calcining, gypsum is converted to plaster of paris (the hemihydrate of calcium sulfate, CaSO4 ½ H2O) which when mixed with water will set or harden as the calcium sulfate returns to the dihydrate form. This semifinished product, usually called stucco, is then manufactured into a large variety of plasters, wallboard, and block for construction use, or into plasters for industrial applications. About 75% of the gypsum used in the United States is calcined for these purposes. Uncalcined uses of gypsum are principally as a retarder for portland cement, as a soil conditioner, as a mineral filler, and other minor industrial applications. About 25% of the gypsum mined in the United States goes into these markets; however, in less developed countries where construction and other industrial uses may be quite limited, the use of uncalcined gypsum for portland cement retarder may well be the dominant-if not the only-market for the mineral. It has often been noted that calcium sulfate constitutes the world&apos;s largest reserve of sulfur, and minor use of both anhydrite and gypsum has been made to produce sulfuric acid or other sulfur compounds such as ammonium sulfate. However, because sulfur is readily available at lower cost from other sources, use of calcium sulfate has been limited to only a few locations where it could compete economically. No such use is reported in the United States at this time. Mineralogy Anhydrite, CaSO4 because of its geologically rapid conversion to gypsum, and relatively high solubility (about 0.2 g per 100 g H2O) is not often found outcropping in climates wet enough to support abundant vegetation except on steeply dipping slopes or other places where hydrated material is continuously removed. Anhydrite rock is most often light to bluish gray in color, and under the microscope, varies

Jan 1, 1983

By Paul Foote

SEEBECK discovered, in 1821, that if, in a closed circuit of two metals the two junctions are at different temperatures, an electric current will flow in the circuit. In the case of an iron and a copper wire, for example, current will flow from copper to iron at the hot junction, or from iron to copper at the cold junction. Two factors combine to cause the current. An electromotive force exists between the two metals, the magnitude of which, depends upon the temperature and upon the metals; this is called the Peltier e.m.f. If a single wire of homogeneous material is heated at one end, an electromotive force is developed between the ends of the wire, the magnitude of which depends upon the metal and upon the difference in temperature; this is known as the Thomson e.m.f: The total e.m.f. acting in the circuit is the sum of the Peltier e.m.f. at the two junctions and the Thomson e.m.f. in each wire, consideration being given, of course, to the algebraic signs of the four e.m.f.&apos;s. The total electromotive force thus depends upon the difference in temperature of the two

Jan 9, 1919