Search Documents

By Walter W. Bradley

FOR a number of years up to the economic setback of the 1929-1931 period, the greatest proportional advances in the mineral industries in California were made among the substances in the nonmetallic groupings, particularly among the so-called industrial minerals and the salines. During the past year or two, although these have not regained the stride that marked their progress in the preceding decade, we can still record, -some new developments. California produces annually between 55 and' 60 different minerals on a commercial scale. Of these, some 40 to 45 comprise the "structural," "industrial," and "salines" materials as grouped in the reports of the State's Division of Mines. Barite-The barite deposits of California were described in Report

Jan 1, 1935

By E. A. Nesbitt

A new permanent-magnet material has been developed with unusual mechanical as well as magnetic properties. Specimens that have been cast or subjected to a small amount of hot reduction by rolling or swaging may be machined, punched, tapped or drilled. The composition range of the alloys is 30 to 52 per cent iron, 36 to 62 per cent cobalt and 4 to 16 per cent vanadium. After being either quenched, annealed or given the usual cold finishing passes and then heated for 2 hr. at 600°C., such materials have a magnetic energy product of 1.0 X 106 gauss-oersteds. This product is equivalent to that of the well-known Honda steel (36 per cent Co, 4W, 2 Cr, 0.8 C. 0.3 Mn, balance Fe). Material handled in the manner just described does not depend on cold-working for its magnetic properties, and is known as Vicalloy I. The preferred composition for Vicalloy I is 38.5 per cent iron, 52 per cent cobalt and 9.5 per cent vanadium. When the alloys are first hot-worked, then considerably reduced in area by cold-swaging, drawing or groove rolling and then heat-treated, the magnetic energy product measured in the direction of previous extension is increased to 2.0 to 3.5 X 106 gauss-oersteds. These higher values have been obtained only after cold reductions in area of 75 to 95 per cent. Material handled in this manner is known as Vicalloy II and the preferred composi-

Jan 1, 1947

By E. A. Nesbitt

A new permanent-magnet material has been developed with unusual mechanical as well as magnetic properties. Specimens that have been cast or subjected to a small amount of hot reduction by rolling or swaging may be machined, punched, tapped or drilled. The composition range of the alloys is 30 to 52 per cent iron, 36 to 62 per cent cobalt and 4 to 16 per cent vanadium. After being either quenched, annealed or given the usual cold finishing passes and then heated for 2 hr. at 600°C., such materials have a magnetic energy product of 1.0 X 106 gauss-oersteds. This product is equivalent to that of the well-known Honda steel (36 per cent Co, 4W, 2 Cr, 0.8 C. 0.3 Mn, balance Fe). Material handled in the manner just described does not depend on cold-working for its magnetic properties, and is known as Vicalloy I. The preferred composition for Vicalloy I is 38.5 per cent iron, 52 per cent cobalt and 9.5 per cent vanadium. When the alloys are first hot-worked, then considerably reduced in area by cold-swaging, drawing or groove rolling and then heat-treated, the magnetic energy product measured in the direction of previous extension is increased to 2.0 to 3.5 X 106 gauss-oersteds. These higher values have been obtained only after cold reductions in area of 75 to 95 per cent. Material handled in this manner is known as Vicalloy II and the preferred composi-

Jan 1, 1947

By Pablo Hadzeriga

Great Salt Lake brine was subjected, in laboratory scale, to conditions simulating solar evaporation. Solid phases and the variation in composition of the liquid phase throughout the potassium salts crystallization zone are presented. These experimental results are discussed and compare with stable equilibrium data of the quinary system Cl-, SO4, Na+, K+, Mg + + and H2O. The Great Salt Lake brine in Utah is a vast reserve of several potential chemicals which has attracted much attention in the recent past. From the standpoint of an ore reserve, it may be said that the lake contains a low grade ore which has to be concentrated by evaporation of water. Because of the fairly favorable weather conditions in the Great Salt Lake area, it seems reasonable to consider solar evaporation as an economical means of concentration. From the view of phase chemistry, the main constituents of Great Salt Lake brine make it belong to the five component system: C1-, SO4=, Na+, K+, Mg++ and H2O. Because of their low concentration, the presence of other elements may be regarded as having little effect on the equilibrium of the five main components. Equilibrium data for the quinary system of our interest has been available for many years. Using these data, it is possible to calculate how the brine of the lake will concentrate when subjected to solar evaporation. In practicing solar evaporation, the weather factor and supersaturation conditions cannot be ignored, but their introduction into calculations using equilibrium diagrams is almost an impossible task. With the experimental work presented in this paper, an attempt is made to compare the stable equilibrium data of the quinary system as applied to the case of the Great Salt Lake brine and the dynamic equilibrium when that brine is subjected to continuous solar evaporation. Sea water brine belongs to this quinary system when only the major constituents are considered. The study of this system has been carried on since the last decades of the nineteenth century. The reason for these intensive studies was to give a geological explanation to the underground potash deposits. AS a result, many theories were presented trying to relate the equilibrium data with the geological formation, paragenesis and metamorphism of these deposits. Two main approaches were followed for the equilibrium studies of this quinary system. One of them, and the best known to us, was the school started in Germany in the last century by J. H. Van't Hoff. The other one, which started about the same time, was the school of N. S. Kurnakov in Russia. Both approaches were different and as a consequence generated opposite theories about the geological formation of potash deposits. The Van't Hoff school studied the quinary system of sea water under careful laboratory control, resulting in stable phase diagrams. During these studies, Van't Hoff recognized the difficulties in crystallizing some double salts.' ". . . . we unexpectedly found that some compounds whose formation in the solutions under investigation was possible at 25°C, nevertheless totally failed to put in an appearance. These, not to mention the calcium salts, were leonite, MgSO4 . K2SO4 4 H2O; kainite, KC1-MgSO4 . 3 H2O; and kieserite, MgSO4 .H2O. Even exceedingly slow crystallization with the addition of the compounds themselves did not remove the condition of supersaturation in the case of these bodies." However, those salts (leonite, kainite, and kieserite) were included in the stable phase diagram at 25°C as shown in Fig. 1 using D'Ans data.3 The figure also shows the sequence of crystallization of the Great Salt Lake brine according to the stable diagram. In later studies by the Van't Hoff school, especially by D'Ans,3 Karsten,4 Autenrieth,5,6 attention

Jan 1, 1968

By L. W. Casteel, E. A. Jones

MINING the lead deposits of Southeast east Missouri has reached a high stage of technical development dictated by the scattered occurrences of low-grade ore through favorable horizons in the Bonne Terre formation. The rock-breaking, handling, and related practices described here have evolved as the best way of mining these particular deposits. These methods are applied in the production of about 19,000 tons of lead ore per operating day from four mines in Southeast Missouri. Development drilling Drifts 10 ft wide and either 8 or 9 ft high are driven in this district on contract. Miners are guaranteed standard wages plus a bonus on the footage advanced, if earned. Labor, fuse, caps, wire, and dynamite used are charged against the contract. Normally the cycle of operations in drifting is performed by a two-man crew, a motor operator and a shovel operator who first load out the rock broken by the preceding shift. The drift crew then sets up two vertical column and mounts the drills. Cleveland HC-10's are used which have a steel lug integral with the cylinder for connection with the air feed. All drilling in drifts is wet. Air pressure is 85 to 100 lb at the face. From 28 to 32 holes are drilled per swing in a pyramid cut. Cut holes

Jan 1, 1947

F. E. Thompson, Pottstown, Pa.: If Mr. Webster's endeavor to open up the subject of cast-iron should prove as prolific of results as did the discussion on " The Physics of Steel," he must certainly feel richly repaid. His remarks concerning the secretiveness and conservatism of the average foundry-man recall to my mind an instance of a blast-furnace which, for the last year, has been producing much foundry-iron. The manager, believing that much more of his product could be used in the foundry than the foundry-men were will-

Jan 1, 1896

By Allan Martin, R. A. Swalin

Diffusion rates of manganese, aluminum, titanium, and tungsten in nickel were measured at temperatures between 1100° and 1300°C. Activation energies, Q, and values of the frequency factor, Do, were calculated for each system. Values of Q were found to be within 15 pet of that for self-diffusion of nickel in agreement with present theories of diffusion. ONE of the most interesting problems in diffusion concerns factors governing the order of diffusion coefficients of various solutes in a common solvent metal at low solute concentrations. An early suggestion by Rhines and Mehl' was that diffusion coefficients might each approach that of the self-diffusion coefficient of the solvent itself. Later Thomas and Birchenall' pointed out correlations between the order of the diffusion coefficients and the freezing point depressions of the solvent by the various solutes. Other correlations have been sought. To settle this question it seems likely that much more data will be needed and, in particular, data collected at low solute concentrations. This type can be obtained by special analytical techniques as well as by use of radioactive tracers. The following study was made of diffusion of manganese, aluminum, titanium, and tungsten in a common solvent, nickel, at relatively low solute concentrations: 1—Production of alloys of nickel with manganese, aluminum, titanium. and tungsten at concentrations of the order of 1 atomic pet. 2—Use of pressure-welded diffusion couples in cylindrical form. 3—Diffusion anneals in the temperature range of 1100" to 1300°C. 4—Lathe sectioning of the diffused couples. 5—Spectrophotometric analyses of lathe turnings for the solute being studied. 6—Calculation of the diffusion coefficient for each of the solutes as a function of temperature. 7—Interpretation of results with current theories of diffusion. Experimental Work Materials—Two types of nickel were used in this research. The grade designated as Vacuum melted Mond nickel was used for all diffusion systems except the Mn-Ni system for which the Vacuum melted electrolytic nickel was used. Analyses of the two grades are given in Table I. The manganese used in making alloys was 99.9 + pet pure, aluminum 99.99 pet pure, titanium 99.9 pet pure, and tungsten of C.P. grade powder. Alloys used in this investigation were prepared by melting in vacuo or under a low pressure of argon. After melting, all heats except those of nickel-manganese were poured into a cylindrical copper mold 3 in. long and 1 in. ID. In the case of nickel-manganese, the alloys were solidified in the melting crucible. For nickel-aluminum heats alumina crucibles were used and for all other heats, zirconia crucibles.

Jan 1, 1957

CONTENTS PAGE Simons, Theodore.-Basic Principles of Gravity Concentration-A Mathematical Study : :.. 1 Taggart, Arthur F. and Gaudin, A. M.-Surface Tension and Adsorption Phenomena in Flotation 11 Hersam, Ernest A.-Factors Controlling the Capacity of Rock Crushers 12 Shaw, S. F.-The Ore Deposits of Sierra Mojada, Coahuila, Mexico 12 Wilson, Philip D.-The British Columbia Batholith and Related Ore Deposits 26 Greensfelder, N. S.-Shot-firing by Electricity 27 Mitke, Chas. A.-Metal Mine Ventilation in the Southwest 28 Foley, F. B. and Howell, S. P.-Neumann Bands as Evidence of Action of Explosives upon Metals 30 Schwartz, H. A., Payne, H. R., Gorton, A. F., and Austin, M. M.-Conditions of Stable Equilibrium in Iron-carbon Alloys 30

Jan 12, 1922

By R. V. Sara

Determination of the Hf-C phase diagram was conducted primarily by metallographic and X-ray diffraction studies on appropriate alloys. The only intermediate phase observed in this binary system was HfC. This phase was found to be homogeneous between 34.0 and 48.0 at. pct C at 2200°c and between 36.0 and 49.3 at. pct C at 3150°C. The lattice-parameter variation was also determined for HfCI-, compositions prepared at 2200° and 3150°C. The most most refractory composition, with a melting point of 3830°c, was established at 47.5 at. pct C from melting-point data. Solidus temperatures of 2240' and 3150°C occur on the high-kafnium and high-carbon sides of the monocarbide, respectively. The invariant point between HfC and carbon is located at 66.0 at. pct C, whereas the 2240°C solidus corresponds to the peritectic temperature at which hafnium is formed from HfC and hafnium-rick liquid. Hafnium has a melting temperature of 2208°C and is capable of taking carbon into solution to the extent of 10.5 at. pct at this temperature. ALTHOUGH the Hf-C phase diagram has not been previously evaluated experimentally in its entirety, the belief has been that the general configuration would resemble the chemically similar Group rV carbide systems, Ti-C and Zr-c.' These binaries are characterized by a single carbide phase with a simple NaC1-type structure which is maintained over wide compositional ranges. This family of carbides has high thermal stability that increases substantially as the atomic number of the metal component increases. This trend characterizes HfC as one of the highest melting materials. According to Agte and Alterthum,2 the melting point for this monocarbide is 3890°C, a value that has been quoted quite extensively for the past several decades. Recently, in repeating the work of Agte and Alter-thum, Adams and Beall3 determined the melting point of HfC to be 3895°C. A significant departure from the commonly accepted version of the Hf-C system was reported by Avarbe and his coworkers,4 who proposed that there is an extreme stabilization of a hafnium in a narrow field to 2820°C, above which it melts peritectically to form HfC and liquid. Their study was also concerned with the melting temperature of various HfCI-, compositions, but the peak melting point was taken from the work of Agte and Alterthum. Avarbe and his associates were not concerned with the high-carbon region of the system. However, three widely varying temperatures have been reported for the HfC-C solidus by other investigators. Cotter and Kohn5 observed approximately 2800°C; Portnoy et al.' reported 3260°C; and, more recently, Krikorian7 indicated 2915°C. Equally as uncertain is the solidus between hafnium and HfC. As noted above, Avarbe et al. report a peritectic temperature of 2820°C, Krikorian7 measured 2150°C, and Benesovsky and Rudy' estimated 2000°C on their diagram. I) EXPERIMENTAL PROCEDURE The starting materials for this study consisted of reactor-grade hafnium hydride obtained from Fair-mount Chemical Co., Newark, N.J., hafnium carbide supplied by Wah Chang Corp., Albany, Ore., and Union Carbide spectroscopic-grade graphite, SP-1. The graphite analysis indicated impurities at levels of only 0.5 ppm or less. According to the suppliers, the hydride and carbide contained the typical impurities listed in Table I. The samples required for these studies were prepared by dry blending either graphite and hafnium hydride or hafnium hydride and hafnium carbide powders for approximately 5 min in a "Spex Mixer Mill". The latter combination was used only for preparing several samples in the HfC1-, melting-point studies. Small pellets, varying between 3/16

Jan 1, 1965

By Joseph Hyde Pratt, Douglas B. Sterrett, CHAPEL HILL

I. DESCRIPTION. MONAZITE is one of the minerals which, for a long time, was considered rather rare in its occurrence, but, upon a commercial demand arising for it, prospectors and engineers soon located large deposits of it in the Carolinas and Brazil, and the supply has always been able to meet the demand. During 1908 further sources of supply of monazite have been discovered and developed in Idaho. North and South Carolina, however, are the only States that have thus far put any monazite on the market. Monazite is essentially an anhydrous phosphate of the rare-earth metals, cerium, lanthanum, and didymium (Ce, La, Di)PO;. There is nearly always present a varying but small percentage of thoria, ThO2, and silicic acid, SiO, which are very probably united in the form of a thorium silicate, ThSiO4 Some monazites contain but a fraction of a per cent. of thoria, while others have been recorded that showed the presence of from 18 to 32 per cent. ; but the majority contain from 3 to 9 per cent. of this oxide. It is the presence of the thorium oxide that gives the monazite its commercial value. The analysis occasionally shows also the presence of other constituents, as the yttrium and erbium oxides, zirconia, alumina, magnesia, lime, iron oxides, manganese oxide, and titanium oxide. Monazite is light-yellow, honey-yellow, reddish-, brownish-, or greenish-yellow in color, with a resinous to vitreous luster, and is translucent to subtransparent. It is brittle, with a conchoidal to uneven fracture, and is from 5 to 5.5 in hardness, and from 4.64 to 5.3 in specific gravity. It crystallizes in the monoclinic system, and some crystals have been observed that were 6 in. in length. The more perfect crystals are, however,

Jun 1, 1909

MINING METHODS W. J. COULTER, Chairman P. B. BUCKY, Vice-Chairman CLYDE E. WEED, Vice-Chairman ROBERT S. PALMER, Secretary Alluvial Mining CLINTON BERNARD O. B. FERRY NORMAN CLEAVELAND C. M. ROMANOWITZ R. B. EARLING J. B. STAPLER BENERE H. GRANTCHARLES THURMAN

Jan 1, 1944

By E. Rudy, St. Windisch

The only complete phase diagram investigation of the Ti-W system is by Maykuth and coworkers,&apos; Fig. 1. Although previous work by Gonser2 indicated complete miscibility, later investigations3°5 essentially confirmed the diagram depicted in Fig. 1. The present study was undertaken because preliminary results on metal-rich ternary Ti-W-C alloys indicated complete solid solubility between 0 titanium and tungsten at temperatures above 1300°C—in contradiction to the presently accepted diagram. The powdered elements, as well as crystal bar titanium and tungsten sheet, were used in the preparation of the experimental alloys. The iodide titanium, obtained from Foote Mineral Co., Exton, Pa., had a total impurity content of less than 410 ppm, of which 150 ppm were interstitials (H, O, N, C). The overall purity of the titanium powder (Var-Lac-Oid Chemical Co., New York) was better than 99.7 pct. Major contaminants, in ppm, included: 0, 800; N, 10; H, 1500; Fe + Co + Ni + Cu + Zn, 50; C1, 200. The measured lattice parameters of the titanium were a = 2.94A and c = 4.68,A. The tungsten sheet and the tungsten powder (Wah Chang Corp., Albany, Ore.) contained the following impurities (in ppm, values in parentheses refer to the sheet tungsten): Mo, 50 (70); 0, 140 (110); Fe, 20 (60); Ni, 20 (not determined); N, 110 (not determined); sum of other impurities, <60 (<100). Samples from the iodide titanium bar stock and from tungsten sheet were prepared by repeated melting of the chipped materials in a nonconsumable electrode arc furnace under high-purity helium. The melted alloys were heavily cored, and homogeneity of the alloys could only be achieved after prolonged heat treatments at subsolidus temperatures. The majority of the alloys were therefore prepared by cold compacting the well-mixed powders in steel dies and pre-homogenizing the compacts for 6 hr at 1300°C in a tungsten-element furnace. The vacuum was better than 10"6 Torr, but for additional protection the sample container was wrapped in zirconium foil. Both preparation methods led to identical results. The measurements of the solidus temperatures were carried oat in the Pirani-type furnace described in a previous paper.6 Incipient melting in alloys containing between 20 and 90 at. pct W was rather difficult to detect visually, and therefore a photoelectric transducer system7 was employed to indicate the phase change. For the investigation of the solid-state equilibria, the specimens were first homogenized for 2 hr at slightly subsolidus temperatures in the Pirani fur- nace and then reequilibrated at, and rapidly cooled (-100°C per sec) from, the selected equilibrium temperatures. After the runs, the alloys were analyzed microscopically and by X-ray diffraction. With the exception of spot checks for oxygen and nitrogen in processed alloys, no other chemical analyses were performed. However, as the weight changes of the alloys during processing were within 0.05 pct and the lattice parameters of indeqendently prepared alloy series agreed within 0.0015A, it is reasonable to assume that no significant concentration shifts with respect to the nominal compositions had occurred. The measured solidus temperatures, shown together with literature data in Fig. 2, ascend smoothly from

Jan 1, 1969

By John D. Morgan, Sylvain J. Pirson

AN instantaneous and continuous analysis of a mineral suspension should be of great value in controlling various mineral preparation processes. Described herein is a method of analysis based on the use of high-frequency alternating current, which, under certain restrictive conditions, could be of use. THEORETICAL CONSIDERATIONS In a suspension of conductive minerals, the electrical effect primarily responsible for the variations in electric conductivity is the capacitance. In Fig Ia, let an alternating voltage E be applied across two electrodes F and F&apos;, between which are two rows (S and T) of mineral particles, all of approximately the same size, immersed in a fluid. Let the number of rows of particles between the electrodes be R and the number of particles in each row be N. If A is the area of a particle, D is the distance separating two particles, and K is a constant depending on the fluid, the capacity, Co, of the particle system will be given by: [KRA C0 ND] Referring now to Fig Ib, let R, the number of rows, be held constant, but let N, the number of particles in each row (S and T), be increased X-fold. The capacity, C1, of [ ]

Jan 1, 1947

By Stanley W. Ivosevic

The South-Central Osa Peninsula produced around 30,000 kg (100,000 troy oz) of gold since prehistoric times. Gold freed by erosion from quartz lodes in the Mesozoic Nicoya ophiolite complex was reconcentrated through three generations of Quaternary sedimentary deposits. Resultant gold placers grade upward from 1 g/m3 (0.03 troy oz/m3) and are of moderate size.

Jan 1, 1980

By H. A. Deans

A three-parameter mathematical model for one-dimensional flow in porous media is developed. The objective of the model is to predict accurately the longitudinal dispersion associated with the flow of either gases or liquids over a wide range of Reynolds number. A qualitative analysis of the model parameters is given. Published experimental pulse-response curves are compared with results predicted by the model. Several general types of problems are given for which the model can be used. INTRODUCTION The problem of multicomponent single-phase flow through porous media is encountered in the study of petroleum reservoirs, gas chromatographic and ion-exchange columns, industrial fixed-bed con-tacters and elsewhere. These particular examples span the wide range of flow conditions possible; Reynolds numbers of less than l0-4 are not unusual in oil-production problems, while values in excess of 103 are common in large fixed-bed operations. The study of flow-dependent transport phenomena is complicated both by the changes in the character of the flow over this range, and by the irregularity of the flow boundaries inherent to porous media. Dispersion is one of the important phenomena known to depend fundamentally on flow conditions as well as on fluid and medium properties. As used in this paper, the term "dispersion" refers to the observed mixing of fluid elements of different composition which occurs in flow systems. The actual mechanism may be one or more of a number listed below. Only dispersion in the direction of the mean flow (referred to as axial or longitudinal dispersion, or mixing) is considered here, although lateral dispersion arises as part of certain coupled mechanisms. MECHANISMS FOR LONGITUDINAL DISPERSION A number of distinct mechanisms are known3,5,7,8 to contribute to the phenomenon of longitudinal dispersion. The more important of these are as follows. 1. Molecular diffusion in the flow direction. 2. Turbulent (cell) mixing. 3. Lateral transport processes coupled with velocity and/or residence time distributions, including: (a) "Taylor" diffusion caused by the interaction of velocity profiles in individual voids with lateral molecular diffusion; (b) separation and remixing or interdiffusion of streams having different velocities around particles; and (c) the couplipg of gross velocity profiles, caused by viscous instability or inhomogeneous porosity, with lateral dispersion. 4. Finite mass-transfer rate between a porous matrix and the flowing phase, and finite diffusion rate inside elements of the porous matrix. It is a well documented fact that these mechanisms, whether acting individually or in combinations, produce essentially similar integral effects. The observed dispersion can be described approximately by solutions of the diffusion equation with a properly chosen dispersion coefficient. Necessary conditions for equivalence between dispersion and diffusion are discussed by Klinkenberg and Sjenitzer.7 Apparently these conditions are not satisfied exactly in many real systems. "Best fit" solutions of the diffusion equation often depart appreciably from measured breakthrough curves for the usual pulse- or step-forced experimental systems. In particular, pulse response curves usually show some degree of asymmetry and "tailing" which cannot be reproduced by the one-parameter diffusion model. The three-parameter model proposed herein attempts to produce these effects in a realistic manner. Asymmetry and tailing are predicted for certain sets of parameter values, while for other sets the new model agrees with the diffusion model. VELOCITY DEPENDENCE OF DISPERSION Molecular diffusion apparently controls at sufficiently low Reynolds number in both gas and liquid systems.*l3 At Re > 20, turbulent cell mixing is dominant for gases flowing at low pressure; the data of McHenry and Wilhelm8 show that the mixing cell is approximately 1 particle diameter long in random sphere packs. on the other hand, the data

By Stanley J. LeFond, Neal Davis

Drilling an oil well or most other types of drilling or coring is no longer a simple and uncomplicated operation. Drilling today at depths which exceed 9144 m (30,000 ft) is hazardous and requires personnel with long and varied experience in drilling. It also requires extensive experience and knowledge in the use of materials which are added to the drilling fluid or "mud," more often than not materials utilizing an industrial mineral. The drilling fluid can vary from a simple mixture of water and "mud" to a very sophisticated, scientifically compounded drilling fluid. Industrial Minerals Used in Drilling Fluids Industrial minerals which are commonly used in oilwell drilling and completion are listed in Table 1. The most important minerals, determined by sales, are bentonite and barite. The other minerals listed are either used to achieve a specific purpose or are used regularly but in limited quantities. The main suppliers of drilling fluids internationally are Magcobar Div., Dresser Industries, Inc.; Baroid Div., National Lead Co.; IMC Drilling Mud Co., (a subsidiary of international Minerals and Chemicals Corp. and Halliburton Co.); and Milchem, a division of Baker Industries. Most of the industrial minerals are found in North America, with barite mines and processing plants located in Nevada, Arkansas, Missouri, and Arizona, and bentonite mines near Graybull, WY. Other mines, such as those in Nova Scotia, are capable of shipping to South America and to the European and Middle East countries. Most of the materials processed by any of the suppliers must conform to specifications set by the American Petroleum Institute (API) or the Oil Companies Material Organization (OCMA). These specifications provide for uniform physical and chemical properties of the materials to be sold on the open market. Function of Drilling Fluids In the early days of rotary drilling, the primary function of drilling fluids was to bring the cuttings from the bottom of the hole to the surface. Today it is recognized the drilling fluid has at least ten important functions: 1) To remove the cuttings from the bottom of the hole and carry them to the surface. 2) To cool and lubricate the drill string and drill bit. 3) To build an impermeable cake on the wall of the hole. 4) To control subsurface pressures. 5) To hold cuttings and weight material in suspension when circulation is interrupted. 6) To release sand and cuttings at the surface. 7) To support part of the weight of drill pipe and casing. 8) To reduce to a minimum any adverse effects upon the formation adjacent to the hole. 9) To insure maximum information about the formation penetrated. 10) To transmit hydraulic horsepower to the bit. In order to accomplish some or all of these functions while penetrating formations of various characteristics, several types of drilling fluids systems have been designed. Types of Drilling Muds There are two basic drilling fluid systems-water-base muds and oil-base muds. There is a wide variety of groups within these two main

Jan 1, 1983

By TSUYEE PEI

I FEEL greatly honored and appreciate this opportunity to be able to say a few words about that rather perplexing subject, silver. The constant decline in the price of this metal has now reached the stage where it is of much concern and the cause of serious discussion among the leading financiers, economists, and statesmen of the world. Further- more, it is significant that this subject is so important that almost every day one can read articles pertaining to it in the newspapers and trade publications. Being essentially a banker, and not an economist, I do not claim to be an authority on the silver question. These remarks are merely some of my observations in, regard to the many puzzles which-I came across in my recent studies of this very important question.

Jan 1, 1931

[SWEETSER, R. H.: Discussions: on Evaluation of Coal for Blast furnace Coke, 94, 378, 394,385 on Mt. Union Sand Flotation Plant for Preparing Bituminous Coal, 74, 591 on Need for Research in Foundry Pig Iron, 76, 450 on Pig Iron Low in Total Carbon, Is in Demand for Use in Various Industries 75,471 on Properties of Coal Which Affect Its Use in the Ceramic Industry, 101, 254 on Relation of Ash Composition to the Uses of Coal, 74, 471 on Research on Blastfurnace Slags 100, 137.138 on Selection of Coals for the Manufacture of Coke, 74, 637 on Sinter in Blast-furnace Burdens, 100, 54 on Sintering Limonitic Iron Ores at Ironton, Minnesota, 90, 355, 356 on Slag Control in the Making of Iron and Steel, 116, 104, 115, 116 on Solubility of Nitrogen in Liquid Iron, 116, 193, 194 on A Statistical Analysis of Blast-furnace Data, 96, 70]

Jan 1, 1936

By E. A. Gulbransen, J. W. Hickman

DURING the past two decades considerable progress has been made in the art of manufacturing heater alloys. The conventional iron-chromium-nickel alloys have been improved by the addition of small quantities of other elements. Up to the present time, to our knowledge, there has not appeared a systematic study of these alloys where the newer tools of investigation have been brought to bear on the problem. It is not yet clear what roles the additional elements play in increasing life time in usage. As a first approximation one might guess that elements such as manganese, silicon, zirconium, calcium and aluminum would aid in the formation of a protective film on the alloy surface, thus retarding the oxidation rate and increasing lifetime. If these additional elements do form protective oxides in the outer surface of the oxide film, it may be possible to identify them by means of reflection electron diffraction. It is also possible that the additional elements may not diffuse to the surface but may remain at the interface between the oxide and the metal. Then, too, the major elements in the alloys undoubtedly form oxides which are stratified on the surface. If the minor elements concentrate in a layer in contact with the substrate where they undergo oxidation and if this oxide film offers resistance to the diffusion of iron, chromium and nickel ions, then the lifetime of the heater element might be expected to increase. It is also possible that preferential reduction in the diffusion rates of the several ions may Occur to such a degree that oxides may form in the body Of the film and On the outer surface which are different from those that would normally form if the additional elements were not present. The use Of transmisson electron diffraction may aid us in jnterpreting these phenomena. UP to the Present time all Of the factors which influence the lifetime of a given heater element are not definitely known. Among these are: (I) The rate of oxidation of the alloy. This may be dependent upon the composition and the physica1 state of the "alloy. (2) The stability of the structure of the coating which forms. Transitions from one structure to another or solid phase reactions resulting in a change of composition may occur. The tendency of the film to adhere to the substrate when heated and cooled successively will be important. (3) The evaporation of various constituents from the alloy such as the remova1 of carbon by Oxygen in a decar-burization reaction. With these possibilities in view, an electron diffraction study of the oxides occurring on six different nickel-chromium alloys was undertaken with the hope that the results of this study could be correlated with oxidation rate studies as determined by means of the vacuum microbalance method1 and with lifetime tests carried

Jan 1, 1949

By Mi Chung

T HE ore-dressing problem at Tul Mi Chung is complicated by the unusually complex nature of the ores. These come from replacement ore- bodies in limestone at the contact with a granite batholith, and contain copper, gold, silver, bismuth, molybdenum, iron, arsenic, zinc, and lead, the first two metals constituting the principal sources of profit. Iron is present as pyrite, magnetite, and hematite. Arsenic occurs both as mispickel and lollingite (FelAsa), the latter carrying a certain amount of finely divided gold. The gangue minerals are those typical of limestone con- tact-metamorphism and include a large percentage of garnet, together with diopside, serpentine, calcite, epidote, zoisite, actinolite, &apos;mica and other minerals. A part of the gold occurs in a free state; some is combined with chalcopyrite and lollingite, and a consider- able proportion is contained in the pyrite. Researches towards the improvement of recovery have been energetically conducted since 1915. Amalgamation, gravity concentrating tables, vanners, can- vas plants, etc., have all been tried and discarded in favor of flotation. It was very quickly established that fine grinding was essential for satisfactory recovery. This was and is still accomplished in Hardinge ball and pebble mills. A comparative test showed that when the ore was crushed to the point at which it contained 20 to 26 per cent. coarser than 100 mesh, the gold recovery was only 55.9 per cent., whereas when crushed so that only 11 to 15 per cent. was coarser than 100 mesh, the gold recovery was increased to 82.5 per cent. No particular difficulty was ever experienced in making a satisfactory recovery of copper but the losses in gold were considered serious and led to the investigation described in this paper.

Jan 1, 1924