Search Documents

Discussion of the paper of EDGAR L. NEWHOUSE, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin: No. 92, August, 1914, pp. 1801 to. 1806. G. C. RIDDELL, East Helena, Mont.-As nearly as I can recall at the present moment, there are only four or five large plants on the continent where the lead on charge is carried in the neighborhood of 40 per cent. These are at Herculaneum, Collinsville, and Federal, Ill.; Trail, B.. C.; and East Helena, Mont. Our object at the latter point is to smelt a maximum amount of Coeur d'Alêne lead sulphides in as compact and self-fluxing a charge as possible, and to this end we are now smelting a mixture that at times carries up to 42 per cent. lead. The monotony of producing the 7,000 tons of bullion shipped each month to. the Omaha and Chicago refineries is relieved somewhat by the fact that the 15,000 tons monthly of Coeur d'Alêne ores that are com-ing to us carry enough zinc to provide the one-half slag used with from 6.5 to 7.5 per cent. zinc clay after day. During the month of March, 1914, three lead furnaces in continous operation, each 136 in. long, averaged 249 tons per furnace clay, exclusive of coke and slag shells, which is smelting at the rate of 5.5 tons per square foot of tuyère area. The

Jan 11, 1914

By W. M. Lehrer

RECENT development of high-temperature brazing alloys has required information regarding the eutec-tic temperature and composition of the Pd-rich section of the Pd-B system.. Literature on this subject was found to be scanty with no complete system yet determined. Buddery and welch1 report an inter-metallic compound occurring in the Pd-B system at 6.33 wt pct B (PdsBz). Another source, Sieverts and Bruning,2 indicates that after annealing at 700°C, a 1.6 and a 2.0 wt pct B alloy were two phase whereas a 0.75 pct B alloy was single phase. Recent work3 using a hot-stage microscope has proposed a eutectic temperature of 743OC. This method utilized the observation of the onset of incipient melting at grain boundaries. The eutectic composition, however, was not determined. METHODS AND PR0CEDURES Five alloys were prepared by triple inert arc-melting high-purity palladium (95.98 pct) with additions of 2 to 6 pct purified amorphous boron. The alloys were crushed within a hardened steel mortar with a steel pestle. The 2 pct alloy, however, was too tough to be crushed in the above manner so was crushed by successive reductions through a rolling mill. Approximately 17 to 18 g of the crushed alloy was used in the thermal analysis. The alloys were melted in pure quartz crucibles. The thermocouple protection tubes were also of quartz and fused along the inside wall of crucibles to prevent floating of the thermocouple. This was an expediency as centering of the thermocouple in the melt would have been preferable. Melting was done in a tube furnace with a slow flow of tank helium maintained as a protective atmosphere. Heating and cooling rates were maintained at 3.5OC per min through the critical temperature ranges by means of a synchronous motor hook-up to a furnace controller. All specimens were heated to 100°C over the indicated liquidus on heating prior to reversing to the cooling cycle. Specimens emerged from the furnace with mirrorlike brightness attesting to the protective quality of the helium atmosphere. Thermal arrests were detected by the differential thermocouple technique using chrome l-alumel couples and nickel as the reference specimen. Arrests were recorded on a Leeds-Northrup automatic X-Y recorder. The specimen temperature and temperature difference were read to + 7.5OC and ± 1.5OC, respectively. These readings were well within the sensitivity of the instrument amplifier. Chromel-alumel couples were used in lieu of Pt-Rh as very few arrests were contemplated in excess of 1200" to 1300°C, the approach of instability. No standardization was performed on these thermocouples subsequent to their use. RESULTS The thermal arrest temperatures obtained are plotted in Fig. 1 as a function of wt pct B. The composition function was obtained by chemical analysis of portions of the specimens after the thermal analysis was completed. The 2 to 6 pct nominal alloys were found to have 1.80, 2.35, 3.65, 4.18 and 5.90

Jan 1, 1960

By Robert C. Linares

Cubic zinc sulfide has been grown from molten salt solutions substantially below the hexagonal-cubic phase transition of 1020°C. Crystals free of birefringence have been grown from molten lead chloride at temperatures from 500° to 800°C. Factors affecting the optical transmission and the birefringence are discussed. CUBIC zinc sulfide is of interest for electrooptic devices and as an optical coating material. However, it cannot readily be produced as large crystals which are free of birefringence. The birefringence arises from the fact that the cubic ZnS is usually grown as the high-temperature hexagonal phase and is transformed to the lower cubic phase by annealing.' This results in stacking faults, stress, and birefringence. A requirement for the growth of cubic ZnS is that it be grown below the phase transition of 1020°C.2 Crystals of cubic ZnS have been grown below 1020°C by the hydrothermal,3 flux,4 and vapor transport5 techniques. However, these all appear to have limitations in size or quality of material produced. It was felt that a new flux method might have a good chance of overcoming some of the previous problems. Mita6 reported the growth of hexagonal ZnS from molten NaCl and wilke7 reported the growth of iron sulfides from molten lead chloride solution, indicating that molten chlorides make good solvents for sulfides. An investigation of a number of possible molten chlorides as solvents showed that molten PbCl2 has an appreciable solubility for zinc sulfide and that crystals can be grown at temperatures from 500° to 800°C. EXPERIMENTAL Crystal growth was performed in open or sealed Vycor or fused silica tubes, in an argon atmosphere or vacuum. There were no deleterious effects due to using vacuum; however, a sealed essentially isothermal system must be used to prevent vapor transport mechanisms from dominating. This will be discussed later in detail. Noble metal containers were not usable as they were severely attacked by these melts. The materials used were: reagent-grade PbC12, reagent-grade ZnS, optical-coating-grade ZnS, and Irtran 2 (ZnS). Crystal growth was accomplished by both slow cooling techniques and gradient growth techniques. In the slow cooling techniques, 15 g of ZnS and 100 g of PbCl2 were used. The components were placed in the silica tube, heated at 800°C for 2 hr, and then slowly cooled (l° to 10° C per hr) to 500°C. The furnace was constructed so that the tube could be inverted, thus allowing the liquid to drain off the crystals at the end of the run. The gradient runs were made by placing the above mixtures in a silica tube at 550° to 600°c, Fig. 1. A temperature gradient was maintained such that the floating mass of undissolved sulfide was 10° to 50°C warmer than the bottom of the tube. Growth occurred on spontaneously nucleated sites at the cooler bottom. RESULTS When using high cooling rates (5° to 10°C per hr), crystals form in thin sheets perpendicular to the {111} face. Crystals 5 by 5 by 1.2 mm, Fig. 2, have been ob-

Jan 1, 1969

By V. Koump, T. F. Perzak, R. G. Olsson

The vate of dissolutioz of carbon in molten Fe-C alloys urns studied by votating- cylindrical g-vaphite sairlples in a stationary crucible containing the melt. The rate of dissolltion was determdined from the change in the bnth co)npositiorz. Alccss-tvansfev coeffi'cients, calcilated with the assurlption that the inte)yacial liquid ulas saturated with carbon, were found to be in agreement with an existing Correlation fov mass transfer jroni votating cylinders. It is corzcllrded tlat, itz the wnge of- Reynolds' numbers itzvestigated (790 to 18,000), the vate of dissolutio of carborz in Fe-C alloys is controlled by tile rate of carbon difirsion from the interface. The dissolution of carbon in molten Fe-C alloys has been the subject of a number of investigations. Most of these investigations have been inconclusive because of poorly defined experimental variables. Two of the more sophisticated studies are summarized below. Dahlke and Knacke' studied the phenomenon by, in part, immersing graphite rods into 0.5 pct carbon-steel for different lengths of time. Since the experiments were conducted in air or in CO atmospheres, the melt was strongly agitated by gas evolution. It was concluded that the change in bath composition as a function of immersion time was in agreement with the assumption that the dissolution process was transport-controlled. The hydrodynamic conditions in these experiments, however, were not well-defined and gave no indication of the nature of the dissolution process at higher fluid velocities. In a recent study Shurygin and ruk investigated the dissolution of carbon in molten Fe-C, Fe-Si, Fe-P, and Fe-Ni alloys. Small graphite disks were rotated in a crucible containing molten alloys under such conditions that only the lower face of the disk was exposed to the melt. The results of this investigation indicate that, over the range of velocities (100 to 1000 rpm) and bulk liquid concentrations (0.7 to 4.5 wt pct C) considered, the dissolution of carbon in the iron alloys is limited by the diffusion of carbon from the interface to the bulk liquid (a transport mechanism). For the particular geometry used by these authors, exact analytical solutions of hydrodynamic and diffusion problems are aailable. Hence the experimental results obtained by Shurygin and Kryuk permit the evaluation of diffusion coefficients of carbon in the four systems investigated. In the present investigation a series of experiments were conducted in which the rate of dissolution of carbon in Fe-C alloys was measured under conditions which permitted wide variation of the fluid velocity and the carbon concentration of the bulk liquid. Graphite cylinders were rotated at different speeds in a stationary concentric crucible containing various molten Fe-C alloys. THEORETICAL DEVELOPMENT In general, the resistance to mass transfer from a solid interface to a turbulent liquid is assumed to reside in a laminar boundary layer adjacent to the interface. If it is also assumed that the diffusion coefficient is independent of concentration, the steady-state rate of dissolution for the case of arbitrary liquid and solid densities can be obtained from the integration of the equations of continuity. The derivation is similar to that used by Lommel and chalmers4 for the case of pl = ps. The solution, expressed in terms where N = rate of diffusion of the solute from the interface. Exact analytical solutions of the hydrodynamic equation for the boundary layer thickness are available for only a limited number of geometries. Consequently, a mass-transfer coefficient, k, is usually

Jan 1, 1967

By B. F. Fackenthall

The Durham Iron Works of Messrs. Cooper & Hewitt, near Riegelsville, Pa., occupy a site which has been almost continuously the scene of iron-manufacturing industry since 1727. Doubtless if Anthony Morris and his thirteen associates, who in that year erected a blast-furnace on the Durham Creek, a short distance above where the Durham Iron Works now stands, could have had a vision of the improved and enlarged apparatus of their successors, they would have been not less astonished by the huge stack, the hot-blast ovens, and the blowing-engines of the modern blast-furnace, than by the railroad which now follows the bank of the river on which their clumsy " Durham boats " once floated pig-iron to Philadelphia. In one particular, posterity must confess their snperiority. We are told that in November, 1728, they shipped three tons of Durham iron to England. The proprietors of the Durham Iron Works are not now shipping iron to England. The present Durham furnace was built (in place of two smaller ones) in 1874 and 1875, and made its first blast in 1876. A description of it, with other works of the same proprietors, at Trenton, N. J., by A. L. Holley and Lenox Smith, was published in London Engineering for January 31st, and February 21st, 1879. Since that time, a number of improvements, dictated by experience, have been made in the details of the furnace and fittings; and the recent roilclusion of a long and successful blast presents a convenient opportunity for a description of the works and a statement of the results of practice. The accompanying drawings will show the general arrangement of the works. The furnace, Plate I., Figs. 1 and 2, is 75 feet high by 19 feet bosh. The hearth is 11 feet 4 inches in diameter, with seven tuyeres 5 feet 6 inches above hearth-line. The tuyeres project 9 inches into the furnace, making the interior tuyere-circle 9 feet 10 inches in diameter. The front is a modification of Luermaun's

Jan 1, 1886

By Tracy C. Jarrett

In making gold alloys possessing certain physical properties, such i~nportant factors as corrosion resistance, color, hardness and melting points must be considered. All of these requirements depend directly upon the composition. It is possible to obtain the same colored gold alloy by using different compositions, but in doing so one may bring in some undesirable property. Other investigations have been carried on in this field by F. E. Carter,' E. M. Wise12 and L. Sterner-Rainer2 To make a complete study of the effect of composition upon these properties, a systematic investigation was carried on involving a range of copper content from 85 to 65 per cent. Elements such as zinc, silver and nickel were used to replace in part the copper content. The gold content in all the alloys remained constant. Only 10-karat gold alloys of those containing 41.6 per cent gold will be considered. All of the alloys were made in an induction furnace. Each alloy was cast in a 3 by 1/4 by 3/4-in. ingot. The method of obtaining the melting points and making color determinations was described in a previots paper.4 The Rockwell B scale with the 1/16-in. ball and 100-kg. weight was used for all hardness determinations. The submersion of test pieces in concentrated nitric acid is one of the standard corrosion tests used in the optical trade. A test piece in the 50 per cent cold-worked condition, % by 2 by 0.045 in., is blanked from a skip using a die, and the weight loss per square inch of surface is taken as a means of comparison. The time for this test is 2 1/2 hr. of actual submersion of the test picce in the acid. This standard test was applied to all of the 10-karat gold alloys discussed in this paper. The tensile tests were made upon strips of the dimensions shown in Fig. 1. The test pieces after blanking were annealed at 1300" F. for 20 min. and cooled in air. Thc "drop of the beam" method was used in determining the yield point, as there was a very marked "drop" when the yield point was reached.

Jan 1, 1940

By Tracy C. Jarrett

In making gold alloys possessing certain physical properties, such i~nportant factors as corrosion resistance, color, hardness and melting points must be considered. All of these requirements depend directly upon the composition. It is possible to obtain the same colored gold alloy by using different compositions, but in doing so one may bring in some undesirable property. Other investigations have been carried on in this field by F. E. Carter,' E. M. Wise12 and L. Sterner-Rainer2 To make a complete study of the effect of composition upon these properties, a systematic investigation was carried on involving a range of copper content from 85 to 65 per cent. Elements such as zinc, silver and nickel were used to replace in part the copper content. The gold content in all the alloys remained constant. Only 10-karat gold alloys of those containing 41.6 per cent gold will be considered. All of the alloys were made in an induction furnace. Each alloy was cast in a 3 by 1/4 by 3/4-in. ingot. The method of obtaining the melting points and making color determinations was described in a previots paper.4 The Rockwell B scale with the 1/16-in. ball and 100-kg. weight was used for all hardness determinations. The submersion of test pieces in concentrated nitric acid is one of the standard corrosion tests used in the optical trade. A test piece in the 50 per cent cold-worked condition, % by 2 by 0.045 in., is blanked from a skip using a die, and the weight loss per square inch of surface is taken as a means of comparison. The time for this test is 2 1/2 hr. of actual submersion of the test picce in the acid. This standard test was applied to all of the 10-karat gold alloys discussed in this paper. The tensile tests were made upon strips of the dimensions shown in Fig. 1. The test pieces after blanking were annealed at 1300" F. for 20 min. and cooled in air. Thc "drop of the beam" method was used in determining the yield point, as there was a very marked "drop" when the yield point was reached.

Jan 1, 1940

By P. J. Spencer, J. N. Pratt

The vapor pressure of manganese over liquid Mn-Sn alloys has been determined by a high-temperature torsion-effusion technique. Alloys containing from 8 to 100 at. pct Mn were investigated in the temperature range jrom 1280" to 1580" and the measured pressure values were used to calculate the partial and integral thermodynamic properties of the liquid alloys. The activities show small negative departures from ideality while the integral heats and excess entropies of mixing are asymmetric inform, changing from positive to negative with increasing manganese content. The possible contribution of various factors to the observed thermodynamic properties is discussed. COMPARATIVELY few thermodynamic data are available for manganese alloy systems.' Therefore, as part of a continuing program of studies of the thermodynamic properties of transition metal alloys, measurements have been made on various binary alloys involving this element. In recent publications,2~3 investigations of liquid Mn-Cu alloys and of the Mn-Au system in both solid and liquid states have been reported. For the first-mentioned system the work suggested that magnetic interactions may be responsible for the observed form of the thermodynamic properties, while in the second the influence of the electrochemical factor appears to be dominant. The present paper describes a similar study of liquid Mn-Sn alloys. Again the thermodynamic properties have been obtained from vapor pressure measurements made by use of a high-temperature torsion-effusion technique.4 A detailed description of the apparatus and of the experimental procedures used in alloy preparation and pressure measurement may be found elsewhere.2'4 EXPERIMENTAL RESULTS Sixteen alloys, ranging in composition from 8 to 100 at. pct Mn, were prepared from spectroscopically standardized manganese of 99.99 pct purity and tin of 99.999 pct purity, both supplied by Johnson-Matthey and Co., Ltd. One-gram samples of the alloys were obtained by carefully weighing appropriate amounts of the pure components into an effusion cell; this was then suspended in the apparatus and the metals melted together in situ by heating under vacuum to approximately 1550°K. After allowing sufficient time for a homogeneous liquid alloy to be formed, vapor pressure measurements were commenced. These were determined as rapidly as possible at a series of steady temperatures within the range of interest. The duration of experimental runs on individual samples was kept sufficiently short to ensure insignificant varia- tion of alloy composition during investigation. After completing pressure measurements, the alloys were rapidly cooled and their compositions checked by weighing or chemical analysis. All experiments were conducted using effusion cells machined entirely from boron nitride. Measurements were made using a variety of cells with orifice areas ranging from 0.0032 to 0.0075 sq cm and lengths of the order of 0.04 cm; the usual effusion correction factors for orifice geometry and molecular distribution were calculated using Freeman and Searcy's equation5 and had values between 0.6 and 0.75 for the orifices employed here. The vapor pressures of manganese over the alloys were measured at approximately 20°K intervals in the temperature range 1280" to 1580°K. In view of the close approximation of the measured pressures to Clausius-Clapeyron behavior in the experimental temperature range, the data for each alloy have been expressed by equations of the form: logp(atm) =-A/T + B A least-squares computer treatment was applied to the vapor pressure values in order to obtain the coefficients A and B with their associated error. The resulting equations are listed in Table I, together with the equation for pure solid manganese obtained from a previous study.4 To minimize the effect of possible apparatus calibration errors, the activities and partial free energies of manganese in the alloys were calculated by initial reference to the latter equation, obtained from identical torsion-effusion measurements. The immediately resulting thermodynamic quantities, based on a solid manganese reference state, were then converted to refer to the more appropriate supercooled pure liquid manganese standard; tabulated values of the free energies of solid and liquid manganese from Hultgren et al.' were used for this purpose. Partial entropies of solution of manganese were calculated from the temperature coefficients of the free energies and partial heats from the Gibbs-Helmholtz relationship.

Jan 1, 1969

By J. L. Huiatt, R. B. Tippin

Introduction Great Salt Lake Minerals & Chemicals Corp. (GSL), a subsidiary of Gulf Resources & Chemical Corp., is located on the east side of the Great Salt Lake, approximately 20 miles from Ogden, UT. GSL processes brine from the north arm of the lake to produce potash, salt cake, salt, and magnesium chloride brine. Potash fertilizer, in the form of K2SO4 is GSL's primary product. The CSL Sulfate of Potash Complex: The GSL potash complex (depicted in [Fig. 1]) is divided into a solar evaporation pond system and the process plants. The solar evaporation system consists of a 17,000-acre (68.8 km2) ponding operation where the various salts deposit during the summer evaporation season and a harvesting operation which recovers the deposits during the remainder of the year. The harvest is either preconcentrated in the flotation plant or processed directly in the chemical plant where sulfate of potash (SOP) is produced. The chemistry of the lake brine results in a solar deposit containing primarily kainite (KC1 . MgSO4 . 3H20), schoenite (K2SO4 . MgS04 . 6H20), and halite (NaCI), with some carnallite (KC1 . MgC12 . 6H20) and epsomite (MgSOq . 7H20). Other minerals may be deposited, depending upon the weather during the evaporation season. Each year, the solar deposit in the evaporation ponds will greatly depend upon the summer weather conditions, which have in the past proven to be quite unpredictable. Weather may alter both the quantity of the solar deposit and the composition of this deposit. During a "short" evaporation season, the tonnage deposited decreases, but depending upon the short-term weather, the potash mineral content can vary greatly. During an "erratic" evaporation season, with intermittent summer rains or

Jan 1, 1980

SOUTHERN CALIFORNIA SECTION Executive Committee SEELEY W. MUDD, Chairman. C. COLCOCK JONES, Vice-Chairman. FREDERICK J. H. MERRILL, Secretary-Treasurer, 631 Higgins. Bldg., Los Angeles, Cal. RALPH ARNOLD A. B. CARPENTER A. B. W. HODGES WILLIAM F. STAUNTON The third meeting of this winter season tool: place in a private dining room of the Sierra Madre Club in Los Angeles on Feb. 1, 1916, at 6:30 p.m., 22 members and guests being present. In the absence of the Chairman, S. W. Mudd, the Vice-Chairman, C. Colcock Jones, presided. After an enjoyable dinner the meeting was called to order, and the first paper by Ralph Arnold on Conservation of Oil and Gas in the Americas was read by the Secretary. W. F. Staunton then read an important paper on The Influence of California Oil on the Mining Industry of the West. In this he touched upon the uses of oil as a fuel for generating power, especially in connection with the Diesel engine. This paper was discussed it some length by J. F. Mitchell-Roberts, R. B. Moran, F. H. Asbury and L. D. Godshall. The Chair then introduced Robert B. Moran of the California State Mining Bureau, Deputy Supervisor of Gas and Oil, for the' Los Angeles . District, who addressed the meeting on the work of his department. The meeting concluded with A. B. Carpenter's reading of a paper on The California Gasoline Industry by W. R.. Hamilton, Manager of the Ventura Refining Co. F. J. H. MERRILL, Secretary. ,

Jan 4, 1916

By D. G. Westlake

NUMEROUS hydride habit planes in zirconium, Zircaloy-2, and Zircaloy-4 have been observed by various researchers and have been compiled by Louthan and Angerman.1 While only partial agreement exists on the identification of these habit planes, there is a growing consensus that a tensile stress applied on a polycrystalline rod during slow cooling will cause the hydride platelets to lie perpendicular to the tensile axis. walters2 agrees with Louthan and Angerman who reason that "The particular plane on which precipitation will occur is the plane that will result in the maximum relief of stress by precipitation of the low-density hydride." The experiment described below was initiated to test this hypothesis on a single crystal of zirconium. A single-crystalline tensile specimen of zone-refined zirconium, designated number 13 in a previous study,3 had a square cross section with one pair of parallel faces only 4 deg from the basal plane of the hcp structure. The tensile axis was about 86 deg from the (0001) pole, 14 deg from the (1010) pole, and 16 deg from the (1150) pole. The specimen was charged to 50 ppm H by allowing reaction with the correct amount of hydrogen at 1073°K, homogenizing at this temperature for 2 hr, and cooling in the furnace. Two- surface analysis revealed that hydride platelets had precipitated parallel to the three {1010} prism planes. The specimen was heated to 673°K, in air, for 16 hr to bring the hydrogen back into solid solution, and furnace-cooled to 573°K.* It was then stressed in ten- sion at 1.2 kg per sq mm. (This produced a resolved shear stress of 0.6 kg per sq mm for glide on the prism plane with the highest Schmid factor. A higher stress would have produced significant strain at this temperature because the critical resolved shear stress for prism-plane glide in this crystal was only 1.0 kg per sq mm at ambient temperature.) The poles of the three prism planes were at angles of 14, 46, and 74 deg to the tensile axis so that an applied stress would exert normal stresses on the three planes in the approximate ratios 10:5:1, respectively. As soon as the stress was applied, the sample was furnace-cooled to room temperature. It was ground on wet Sic paper and chemically polished in 50 parts HNO3, 50 parts water, and 7 parts HF before examination. The result of the experiment was negative; i.e., the three (1010) planes were of equal importance as hydride habit planes.* It must be admitted that the ex- periment is not entirely comparable to those performed by walters,2 Louthan,5 and Louthan and Marshall6 on polycrystalline materials. They have found that some critical stress (below the macroscopic yield stress) is required for stress-orienting the hydrides. The applied stress in the present experiment was, by necessity, smaller by an order of magnitude than the critical stresses they report for the various materials. If the critical stress was related to the microstructure, one might postulate that it should be decreased by increasing the degree of perfection of the metal lattice and by increasing the grain size. But the experiment above suggests that, for the extreme case of a zone-refined single crystal of zirconium, the critical stress lies above that which one can apply without introducing gross plastic strain as another variable.

Jan 1, 1967

Jan 1, 1971

The meeting of the Board of Directors, on November 22, was attended by eight directors, the Secretary of the Institute, and eight guests. The proposed James Douglas Prize and Tablet was referred to a committee of eleven. Robert H. Richards was appointed representative of this Institute to attend the meeting of the Society for the Promotion of Engineering Education. J. V. N. Dorr was made chairman of the Finance Committee in place of George D. Barron, resigned. The sum of $200 was appropriated for the 1918 expense of the American Engineering Standards Committee; the question of an appropriation for 1919 was referred to the Executive Committee for study and report. The sum of $50 was appropriated to the Treasurer's clerk. The following representatives of the Institute were elected: W. L. Saunders to succeed himself as United Engineering Society Trustee; R. M. Raymond to succeed himself as member of Engineering Foundation Board; S. J. Jennings to succeed himself as member of Engineering Council; George F. Kunz to succeed himself as member of Engineering Council; C. F. Rand to succeed himself as member of John Fritz Medal Board of Award; E. Gybbon Spilsbury to succeed himself as member of the Library Board. To members of the Canadian Mining Institute residing in Canada or Newfoundland, the privilege was extended to subscribe to the Bulletin at the price of $5. An invitation was extended to the Mining and Metallurgical Society of America to consolidate with the American Institute of Mining Engineers. The appointment of Engineering Societies' Employment Bureau was reported. Thirty-nine members and ten associates were elected. Two members were reinstated. Extension of time for the payment of clues was granted to four members. Seventeen members on active duty at the front had their dues remitted.

Jan 1, 1919

By George H. Ashley

At the beginning of the war, about 13 years ago, a conference was called in Washington to lay plans for pooling the coals of the United States. A careful review of the various systems of classification then extant showed none well adapted to the needs of coal pooling. The system of Tidewater pools then adopted, using numbers to distinguish one pool from another, was based on typical coals of different localities. At that time, the writer undertook the preparation of such a practical classification. Aside from drawing on his experience of over 20 years in the coal fields of the United States, reaching from the Pacific Coast and the Rio Grande to Rhode Island, he first examined and carded all of the large collection of coals in glass jars made by and for M. R. Campbell. Next, he carded all of the descriptions of coals he could find in the U. S. Geological Survey bulletins and elsewhere, as well as practical tests of coals by the Navy and other organizations and then took account of every published coal analysis of the U. S. Geological Survey and U. S. Bureau of Mines. A study of this information, involving thousands of recomputations, led to the presentation of a paper on "A Use Classification of Coal" before this Institute at the Chicago meeting, September, 1919. That classification was unique (1) in a classification based on "standard coal" which included moisture, but used standardized ash, sulfur and nitrogen, (2) in using physical properties to distinguish the major classes or orders, (3) in recognizing British thermal unit values in the minor subdivision, (4) in the large number of classes recognized (thirty-six), (5) in proposing mineral names for all classes, (6) in proposing a letter code for the several classes for practical use, (7) in proposing a code for expressing what has commonly been called "grade" of the coal, the grade code to be combined with the rank code to designate and describe a coal. The writer still thinks that the principles then offered, though not necessarily the exact proposals, are valid and desirable in any practical classification. The actual classification of coal by rank was based on the ratio of fixed carbon to volatile matter for the high-rank coals—the well-known

Jan 1, 1930

By Charles L. Mantell, James E. Hoffmann

Mechanical inclusion, electrophoretic deposition, and adsorption were studied as mechanisms for code-position of aluminas present in copper-plating electrolytes as an insoluble disperse phase. Mechanical inclusion was not a significant factor. That codeposi-tzon of aluminas by an electrophoretic mechanism was unlikely was substantiated by measurements of the potential of the aluminas. The alumina content of the deposits was studied as a function of the pH of the bath. These tests in conjunction with sedimentation studies demonstrated the absence of an isoelectric point for the alutninas over the pH range examined. Thiourea in the electrolyte (a substance known to be adsorbed on a copper cathode during electrodeposition) affected the amount of alumina in the electrodeposit. However, no adsorption of thiourea on aluminas in aqueous dispersions was detected. If it were possible to produce a dispersion-hardened alloy of copper and alumina by electrodeposition, an alloy possessing both strength and high conductivity at elevated temperatures might be anticipated. Investigation of the mechanism of codeposition of aluminas with copper was undertaken with the hope that knowledge of the mechanism would aid in the development of such an alloy. The word "codeposit" here does not necessarily imply an electrolytic phenomenon but rather that the materials codepositing, the various aluminas, are transported to and embedded in the electrodeposited copper by some means. Mechanical inclusion in electrodeposition implies a mechanism of codeposition which is wholly mechanical in nature; the only forces acting on a particle are gravity and contact forces. Such a particle is presumed to be electrically inert and incapable of any electrical interaction with electrodes in an electrolytic plating bath. Processes for matrices containing a codeposited phase by electrodeposition from a bath containing a disperse insoluble phase frequently state that code-position is caused by mechanical inclusion.10,2,12 If settling, i.e., gravity, be the controlling mechanism for codeposition of aluminas, then assumptions may be made that 1) the content of alumina in the electrodeposit should be enhanced by increasing the particle size, 2) the geometry of the system, that is, the disposition of the cathode surfaces relative to the di- rection of the falling particles, should affect the alumina content of the electrodeposit, 3) in geometrically identical systems the chemical composition of the electrolyte employed should exercise no effect on the alumina content of the deposit, that is, the alumina content should be the same in all cathode deposits irrespective of bath composition. A bent cathode19 evaluates the clarity of filter effluent in electroplating baths by comparing the roughness of the deposit on the vertical surface with that on the horizontal surface. Two difficulties are inherent in this technique: 1) the current density on the horizontal portion of the cathode would be substantially greater than that on the vertical surface; 2) should the deposit obtained be rough, projections on the vertical face could act as horizontal planes and vitiate the relationship between the vertical and horizontal surfaces. Bath composition should have no substantial effect on the alumina content of the deposit. Two different electrolytic baths were employed. They possessed variant specific conductances and substantially different pH ranges. The experimental tanks were rectangular Pyrex battery jars 6 in. wide by 3 1/4 in. long by 9 3/4 in. deep. The cathodes were stainless steel 316 sheet of 0.030 in. thickness, cut to 7.5 by 1.75 in. and bent at right angles to form an L-shaped cathode whose horizontal surfaces measured 1.75 by 3.0 in. All edges and vertical surfaces were masked with Scotch Elec-troplaters Tape No. 470. The anodes were electrolytic cathode copper 9 in. high by 2.25 in. wide by 0.5 in. thick. To eliminate inordinately high current densities on the projecting edge of the cathode, the anode was masked 1 in. above and below the projected line of intersection of the cathode with the anode. The exposed area of the anode was equal to that of the cathode, providing both with equal average current densities. The agitator in the cell was of Pyrex glass and positioned so its center line was equidistant from cathode and anode, and a plane passed horizontally through the center of the blade would be located equidistant from the bottom of the cathode and the bottom of the deposition tank. The assembled apparatus is depicted in Fig. 1. Hatched areas on anode and cathode represent the area of the electrodes wrapped with electroplaters tape. MATERIALS The chemicals were copper sulfate—CuSO4 • 5H2O— technical powder (Fisher Scientific Co.). Spectro-graphic analysis showed substantial freedom from antimony, arsenic, and iron. Traces of nickel were present.

Jan 1, 1967

By C. E. Sims, C. A. Zapffe

AN investigation of the behavior of inclusions in steel several years ago1 led to the conclusion that some of the commonly occurring inclusions in steel have appreciable solubilities, particularly in liquid steel. In the belief that further study and clarification of this matter was warranted, a laboratory study of oxides in liquid steel was started. These oxides are generally the result of deoxidation treatment, and the basis of an understanding of their behavior must be, therefore, the behavior of the deoxidizer in liquid iron. The Fe-Si-O system was selected for the first study, and the apparatus used and experiments conducted are described herein. APPARATUS The apparatus is shown in Fig. I and the system is shown by diagram in Fig. 2. Furnace Atmosphere Commercial hydrogen (1) passes through an orifice (2) into a manometric system that measures the tankside pressure (3) and the back pressure (4) in the system. A water trap (5) guards against excess tankside pressure. A by-pass with stopcocks (6 and 7) is provided, so that the hydrogen can be routed directly from the tank to the furnace if desired. When stopcock 7 is closed and stopcock 6 is open, the gas proceeds through the conditioning train, of which the first unit is a furnace (8) that contains platinized asbestos at 350°C. The temperature is measured by a thermocouple and potentiometer (9) and is controlled by a slidewire resistance (10). In [ ] this furnace free oxygen is converted to water vapor. The exiting gas passes over a water bath (11) kept slightly below boiling temperature by an auxiliary heating unit (12). This unit also heats a surrounding copper coil (13) containing water, and the heated water rises through a collar (14)

Jan 1, 1942

By W. I. Garms, J. L. Stevens

BECAUSE of the many conflicting opinions regarding the functioning of the ball load and the characteristics of ball wear in ball-mill grinding, the following resume of reports covering recent tests conducted at the Hayden plant of the Kennecott Copper Corporation is submitted with the view of pointing out certain salient features that should throw additional light on the subject. MILLS USED Cylindrical drum mills with trunnion feed and discharge were used. The discharge trunnion was I3 1/2 in. in diameter. Dimensions inside the lining were 6 ft. 6 in. in diameter and 9 ft. 6 in. long. The mills were Britannia-lined and nine lifter bars projected 2 in. from the lining. The mill speed was 16 2/3 r.p.m. Feed to the mill was 9 per cent on 10-mesh, 85 per cent on 100-mesh, 77 per cent solids. New balls measured 2 in. in diameter and the approximate weight of the ball load was 40,000 pounds. INITIAL TEST During a test that was being conducted to determine the relative economic value of standard cast balls vs. forged steel balls in the local grinding operation, certain observations were made in regard to the functioning of the various ball sizes and the characteristics of ball wear, which warranted a supplementary test for the purpose of confirming such observations. For the initial test, the necessity for developing a graduated load of the new forged balls before the test could be started was realized, but the time required to obtain a graduated load and the functioning of the various ball sizes was not clear. No advantage could be seen for starting out with a full load of forged balls, as this initial load, at the least, would have to be completely ground out and replaced by daily additions of balls before the graduation could be complete and a normal static condition of ball sizes reached. For a considerable period prior to exhaustion of this initial charge there would be an unusual quantity of worn balls of a certain size, which would not be typical of a normal charge and could influence the characteristics and functioning of the entire load. Therefore, it was decided to start by daily addition of the forged balls to a mill that contained a normal operating load of cast balls. After 88 days of operation the mill was shut down for inspection. By that time the load consisted of a mass of forged balls functioning around a large core of the residual material of the former cast-ball load. This core of cast slugs, locally referred to as "the kidney," was well defined from the forged-ball load.

Jan 1, 1946

By P. L. Raffo, T. E. Mitchell

Single crystals of Ta-Re alloys have been deformed in tension and compression as a function of solute concentration and temperature. The temperature dependence of the yield stress is decreased by alloying. At low temperatures there is a minimum in the yield stress (at about 2 at. pct) as a function of concentration. Three-stage hardening was not observed in the alloys. Linear hardening rates, where observed, were characteristic of stage II in pure tantalum. At low temperatures and high concentrations, work softening was often prominent at high strains. Electron microscopy revealed that dislocations are mostly of screw orientation, although heavily jogged and cusped, and often occurring in dipole pairs. The alloys become more prone to cleavage with increasing rhenium content, due mostly to an increasing yield stress rather than a change in cleavage strength. Alloying apparently decreases the Peierls stress of bcc metals at low temperatures by facilitating kink nucleation at solule atoms on screw dislocations. Higher solute concentrations further increase the yield stress. Quantitative calculations and comparisons with other bcc alloy systems are made to show that the predominant hardening mechanism is due to the interaction of dislocations with misfitting solute atoms close to their slip planes. The interaction is so localized that the core dilatation of dislocations could be important. CONSIDERABLE interest has arisen in recent years concerning the mechanical properties of unalloyed bcc metal single crystals.'-7 These and similar studies on polycrystalline materials have resulted in a considerable understanding of the macroscopic yielding characteristics8, 9 and the process of work hardening.'' This latter advance is due in a large part to the increased use of transmission electron microscopy in P I RAFFO junior Membar AlMF is Metallyureist Iewis such studies and the general observance of three stages of work hardening in the shear stress-shear strain curves. The properties of substitutional alloy single crystals of bcc metals have not been determined in as much detail as in the pure metals. Insufficient systematic studies have been made on the effect of alloying on the magnitude and temperature dependence of the yield stress or the stress-strain curves. The alloy systems which have been studied to some extent have been Ta-W,11, 12 Ta-Mo," Ta-Nb,12'14 Mo-Re,15 W-Re,16 and alloys of iron with nickel,17 platinum,17 vanadium,18 and aluminum.18 A large body of data exists on Fe-Si alloys, but these have mainly been a result of the experimental convenience of using this material in place of unalloyed iron, rather than a comprehensive study of the mechanical properties of the alloy system per se. The present authors have previously reported additional data on the properties of Ta-Re, Ta-W, and Ta-Mo alloy single crystals.1g Some of the data on Ta-Re alloys will be described later in this paper. Briefly, single crystals of Ta-Re (1.2 to 10.6 pct), Ta-W (6.2 and 10.2 pct), and Ta-Mo (2.9 and 9.0 pct) were grown by the floating zone method in vacuum. Compression tests were performed in the temperature range 77" to 623°K. Slip was found to occur in Ta-Re alloys at 77' and 298°K on the (~ll)[lil] system and slip lines were coarser and straighter than in unalloyed tantalum. No three-stage hardening was observed in any of the alloy systems and the curves were nearly parabolic. At temperatures above 175°K the yield stress* increased monotonically with in- creasing composition while at 77" and 175°K the yield stress initially passed through a minimum after which it began to increase again for concentrations greater than about 2 pct Re. Similar minima were observed in Ta-Mo alloys and to a lesser extent in Ta-W alloys. The minimum was interpreted as being a result of a

Jan 1, 1969

By C. E. Sims, C. A. Zapffe

AN investigation of the behavior of inclusions in steel several years ago1 led to the conclusion that some of the commonly occurring inclusions in steel have appreciable solubilities, particularly in liquid steel. In the belief that further study and clarification of this matter was warranted, a laboratory study of oxides in liquid steel was started. These oxides are generally the result of deoxidation treatment, and the basis of an understanding of their behavior must be, therefore, the behavior of the deoxidizer in liquid iron. The Fe-Si-O system was selected for the first study, and the apparatus used and experiments conducted are described herein. APPARATUS The apparatus is shown in Fig. I and the system is shown by diagram in Fig. 2. Furnace Atmosphere Commercial hydrogen (1) passes through an orifice (2) into a manometric system that measures the tankside pressure (3) and the back pressure (4) in the system. A water trap (5) guards against excess tankside pressure. A by-pass with stopcocks (6 and 7) is provided, so that the hydrogen can be routed directly from the tank to the furnace if desired. When stopcock 7 is closed and stopcock 6 is open, the gas proceeds through the conditioning train, of which the first unit is a furnace (8) that contains platinized asbestos at 350°C. The temperature is measured by a thermo-couple and potentiometer (9) and is controlled by a slidewire resistance (10). In [ ] this furnace free oxygen is converted to water vapor. The exiting gas passes over a water bath (11) kept slightly below boiling temperature by an auxiliary heating unit (12). This unit also heats a surrounding copper coil (13) containing water, and the heated water rises through a collar (14)

Jan 1, 1942

By Myron Rodgers

IN rock- or ore-crushing tests all data, in order to be valuable for study and comparison, should be obtained and tabulated under conditions as uniform as possible. The results of many such tests have no value for comparison, because of incomplete data and the lack of uniform conditions, screens and scale of sizing, etc. The purpose of this paper is to suggest a form of standard specifications which may be developed by the Milling Committee and approved by the A. I. M. E. for rock-crushing tests. It is not intended to discuss any theories of rock crushing. Reports of rock-crushing tests should include the following details: 1. Description of the machine employed (jaw or gyratory crushers, rolls, stamps, tube mills, Chilean mills, etc.). 2. Method and material (timber, concrete, etc.) of foundation. Much power is dissipated in the vibration of poor foundations. 3. Locality from which the rock or ore was obtained, and geological, mineralogical, and physical characters of the material. 4. The power consumption of the machine running with no load and with full load, the unit of power being 1 hp, per 24 hr. 5. The capacity of the machine in tons (of 2000 lb.) per 24 hr. 6. The duty in tons per horsepower-day. 7. The screen analysis of feed and product by the proposed A. I. M. E. standard screen scale. On the foregoing statement, the following remarks are offered.

Jan 9, 1915