Search Documents

By Mary Ellen Bruce Large, Antonio Marinucci, Silas C. Nichols

Tip post-grouting of bored pile (drilled shaft) foundations refers to a method where cementitious grout is injected beneath the tip of a shaft to improve the overall performance of the constructed foundation. This technique, when performed satisfactorily and in the appropriate ground conditions, enhances axial load-displacement performance by improving the mobilization of pile’s resistance. Potential benefits associated with tip post-grouting include reduced settlement under loading, better alignment of load transfer curves, and improved ground beneath the base of the bored pile. However, to be able to realize the benefits attributed to this method, the design, construction, of both the bored pile and the post-grouting system must meet a minimum level for quality assurance. The various factors affecting the successful installation and performance of a bored pile (e.g., workmanship, base cleanliness, borehole integrity, and concrete placement) have been discussed by numerous practitioners and researchers in the available technical literature. For a conventional (i.e., ungrouted) bored pile, acceptance is based on a combination of visual inspection, material testing, and the results of integrity and/or performance testing of the constructed pile. A properly executed tip post-grouting program can be a relatively comprehensive and complex process, which is typically evaluated throughout the construction process based on the results of prior projects and/or on test pile(s) at the particular site. For tip post- grouting programs, verification procedures and acceptance criteria should be established during and incorporated into the design process to ensure design intent and objectives are achieved. Project specifications should be produced to ensure performance requirements are achieved. This paper will present and discuss factors affecting the successful execution of tip post-grouting, including grouting criteria, instrumentation, reliability and uncertainty with the method and outcome, and verification and acceptance. INTRODUCTION Constructing bored piles (drilled shafts) is increasingly more challenging given the lack of ideal site locations, tight project site confines, difficult or restricted access, greater demands on drilling equipment, and close proximity to adjacent structures. To evaluate the feasibility of bored piles as an appropriate foundation system, a myriad of factors is evaluated during design, including site conditions and constraints, budgeting and scheduling, reliability and risk exposure, presence of and depth to adequate load bearing soils/rock, and the magnitude of the imposed loading. Moreover, updated design codes increased load demand per element, and improved material strengths have led to more complex foundation designs, larger foundation elements, and significant increases in load magnitude. Monopile (monoshaft) foundations have been utilized where one large bored pile is used in lieu of a group of piles connected via a pile cap. In addition, to accommodate the design criteria, site conditions, and imposed loading, the geometry of the bored piles being designed and installed have been as large as 13 feet (4 m) or greater in diameter and to depths in excess of 260 feet (80 m).

Jan 1, 2018

By Michel G. Grenier

Compliance with Diesel Particulate Matter (DPM) exposure regulation is currently performed using timeweighted average (TWA) sampling on underground mine workers. These samples are collected in the span of an entire shift and the resulting concentrations are compared to a legislated exposure limit. While this is very useful to determine the exposure level of an individual to DPM, it fails to clearly identify causes of exposure and highlight opportunities that could help reduce the exposure of workers in the course of the work shift. Real-time DPM monitoring measures the worker?s exposure as a function of time and helps identify circumstances where corrective actions can be taken or design changes can be made by the individual or the employer to reduce the overall exposure of the worker and peers. This work focused on obtaining DPM concentrations using a real-time polycyclic aromatic hydrocarbon (PAH) monitor. The aim was to demonstrate that this instrument, while not a direct DPM analyzer, was able to provide a concentration profile that could easily be linearly correlated to standard TWA elemental carbon measurements. In addition, several instances of improvements that could be implemented to reduce the exposure of underground employees were demonstrated.

May 1, 2010

By K. S. Rao, R. P. Tiwari, V. K. Shrivastava

ABSRACT: In this paper numerical simulation of jointed block mass behaviour obtained in an experimental study has been presented. Singh et al. (2002) conducted extensive tests on the jointed model materials with several joint configurations. The results of this experimental study were used to validate the strength behaviour of numerical block mass model developed using professionally available software. This software basically contains different kinds of material models. From the results of numerical simulation the existence of strength anisotropy was observed. The strength anisotropy so obtained has been compared with the experimental values reported by Singh et al. (2002). The anisotropic curves in both cases are U-shaped with flat base. They show good agreement in sliding mode of failure zone in which inclination ß (= 90° - ?) of joint set-I lie between 20° to 40° for all cases of interlocking. ZUSAMMENFASSUNG: In dieser numerischen Papiersimulation des verbundenen Blockmasse Verhaltens, das in einer experimentellen Studie erhalten wird, ist dargestellt worden. Singh et al. (2002) leiteten umfangreiche Tests auf den verbundenen vorbildlichen Materialien mit einigen gemeinsamen Konfigurationen. Die Resultate dieser experimentellen Studie wurden verwendet, um das Stärke Verhalten des numerischen Blockmasse Modells zu validieren, das mit professionell vorhandener Software entwickelt wurde. Diese Software enthält im Allgemeinen unterschiedliche Arten der materiellen Modelle. Von den Resultaten der numerischen Simulation wurde das Bestehen von Stärke Anisotrophie beobachtet. Die Stärke Anisotrophie also erreicht ist mit den experimentellen Werten verglichen worden, die von Singh et al. (2002) berichtet werden. Die anisotropen Kurven in beiden Fällen sind mit flacher Unterseite u-förmig. Sie zeigen gute Vereinbarung in gleitender Erscheinungsform des Ausfalls Zone, in der Neigung ß (= 90° - ?) von der Verbindung stellenSie Lüge zwischen 20° auf 40° für alle Fälle vom Ineinandergreifen ein. RESUME: Dans cette simulation numérique de papier du comportement joint de la masse de bloc obtenu en étude expérimentale a été présenté. Singh et autres (2002) ont effectué les essais étendus sur les matériaux modèles joints avec plusieurs configurations communes. Les résultats de cette étude expérimentale ont été employés pour valider le comportement de résistance du modèle numérique de la masse de bloc développé en utilisant le logiciel professionnellement disponible. Ce logiciel contient fondamentalement différents genres de modèles matériels. Des résultats de la simulation numérique on a observé l'existence de l'anisotropie de force. L'anisotropie de force ainsi obtenu a été comparée aux valeurs expérimentales rapportées par Singh et autres (2002). Les courbes anisotropes dans les deux cas sont en U avec la base plate. Elles montrent la bonne concordance dans le mode coulissant de la zone d'échec en lequel la inclination ß (= 90° - ?) du joint placez-Je le mensonge entre 20° à 40° pour tous les cas d'enclencher.

Jan 1, 2003

More than 100,000 people are expected to be in Las Vegas, NV in March for ConExpo-Con/Agg 2002, the largest exhibit of its kind in the Western Hemisphere. This triennial event features equipment, services and technical sessions geared toward the global construction aggregates and ready mix concrete industries. ConExpo-Con/Agg 2002 will take place March 19-25, 2002 at the Las Vegas Convention Center. For registration information, contact the show offices, phone 800-867-6060, 414-298-4141, or 301-587-3140, Website www.conexpoconagg.com.

Jan 1, 2002

By V. Arslan

In this study, effects of the inert constituents, such as ash, and the effect of blending coals with differing rank and composition on the plasticity of coal blends were investigated. The reference coal originated from the Zonguldak region, in the north-west part of Turkey. Firstly, the effect of coal ash on the plasticity of Zonguldak coal was determined. Secondly, the relationship between the plastic properties of the individual coals and those of the blended coals were identified. Some important relations were found, related to the characteristics of the individual coals. Ultimately, the manner in which the plasticity of Zonguldak coal was affected by blending with low volatile coals was investigated. Keywords: coal blending, coal plasticity, coke, fluidity, rank.

Jan 1, 2006

By D Craw, P Upton

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Otago Schist belt of southern New Zealand hosts widespread orogenic gold deposits. Erosion of these orogenic gold deposits has led to the formation of numerous placer deposits distributed across and beyond the host schist belt. Numerical modelling of crustal scale deformation and geomorphic evolution has defined the key tectonic features that have controlled the severance of detrital gold deposits from their sources. Tectonic activity over the past 20 million years, during development of the modern Pacific-Australian plate boundary, has severed links between some placers and their sources. Detrital gold was transported south from the Otago Schist source region in two different river systems in the Miocene. Mesozoic orogenic gold deposits shed gold into rivers that flowed to the south. These rivers were terminated by the rise of north-west-trending basement ridges at the boundary between weak schist crust and strong greywacke crust, and the ridges were controlled by pre-existing faults at that rheological boundary. In contrast, rising mountains close to the developing plate boundary in the Miocene were the locus of new orogenic gold deposits hosted in extensional faults. These gold deposits were rapidly exhumed and contributed detrital gold to orogen-parallel Miocene rivers that flowed to the south-west. Pleistocene deformation on mainly north-west and north-east orientations, and associated river capture, has severed the links between these Miocene orogenic deposits and downstream detrital gold.CITATION:Craw, D and Upton, P, 2015. Tectonic severance of links between placer gold and its sources, southern New Zealand , in Proceedings PACRIM 2015 Congress, pp 541–544 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Braden Lusk, Tristan Worsey, Nathan Rouse, Kyle Hall

Loading explosives up hole has challenges that are typically not seen in down hole explosive loading. Most explosives applications are not up hole. Lack of experience and technology can cause significant problems when loading explosives up hole. When results aren’t achieved, the blame is commonly put on the design when the true problems are unknown. Not knowing the cause of the problem causes drill and blast designs to be over engineered and very costly with little success. Being able to know and record key data is crucial to actually solving the problem. This paper goes over blast instrumentation that can be used to trouble shoot drill and blast problems in up hole explosives loading in underground mines. The tools and procedures used to trouble shoot include velocity of detonation recorder, borehole tracking, seismographs, and borehole camera. Each item will be discussed in detail with a case study to show the usefulness of the instrumentation. The operation discussed in the case study had issues pulling raises and had hang ups in the stope shots. These problems caused production slowdowns and costly remediation blasting that was not very successful. The case study is an underground gold mine that used modified sub-level caving with backfill as the mining method.

Jan 1, 2018

Lignite deposits of Central Otago Miocene Dunstan Formation accumulated on a broad alluvial plain and on deltas that flanked a large freshwater lake. The regional subsurface distribution and configuration of the lignite-bearing strata are identified within the context of depositional systems and placed into a genetically defined stratigraphic framework. The stratigraphic and depositional models constructed, should form an integral part of the geological assessment process to guide future regional or mine based lignite drilling programmes. Further testing and evaluation of the commercialy important lignite deposits in the Blackstone and Roxburgh Coalfields are required to adequately characterise the lignites and their geological setting, particularly to select methods of mining and wise uses of the lignite.

Jan 1, 1992

By Wylie A. W, Mathew P. J, Eisler P. L

Field studies of the radiations backscattered by iron ores from a 60Co source of primary gamma radiation located in a borehole logging probe have confirmed thatthe P" factor, a ratio of high energy gamma ray intensities to low energy intensities in selected energy windows of the backscattered gamma-ray spectrum, is a valuable measure of grade for sedimentary iron ores of the Pilbararegion of Western Australia.Laboratory studies of model boreholes have shown that variations in borehole diameter and variations in bulk density of the formations have a significant influence on the measurement of P" ratios. If these influences 'are taken into account the mean ore grade in a new blast hole, for instance, can be predicted with a probe of suitable configuration to within 0·8 per cent Fe at the 95 per cent confidence level, while the grade of a single 120-cm split can be determined to within 2·6 per cent Fe. These results were obtained by pooling data from five blast holes covering the range of iron concentrations 20-68 per cent Fe and apply to the mean hole grades 54-68 per cent Fe.Results for two development holes were generally comparable to those obtained from individual blast holes95 per cent confidence limits of ±0·9 per cent Fe for mean ore grade and ± 4·1 per cent Fe for single splits. A greater number of data points is needed before these confidence limits can be further improved.The technique utilized to obtain these results was derived from a "multiband" approach to collection of backscattered spectral intensity data, an approach which permitted selection at the data processing stage of the most statistically significant P" ratios for the type of mineralization encountered in the field. The multiband technique also permitted selection of the most significant of another set of windows in the backscattered gammarayspectrum to measure a newly developed "S-factor", a ratio sensitive to borehole diameter. Another window provided information on bulk density. All these measurements were made with a single pass of the same loggingprobe.

Jan 1, 1977

By J. A. Delgadillo

Computer simulation and mineral modeling was applied to the optimization of a grinding circuit in a plant processing 256 t/h magnetite. These tools were used to develop a grinding and classification configuration to decrease the grade of silica in the magnetite concentrate, which is produced by the plant. Empirical grinding and classification models were finely tuned using plant experimental data. The JKSimMetTM 5.0 software was used to simulate the grinding and classification units. By applying changes in the original circuit, a throughput increment of 100% was achieved with an important reduction in the energy consumption. The silica content in the magnetite concentrate can be decreased by regrinding the coarse fraction of fine screens into a separate ultrafine grinding unit instead of returning this flow to the ball grinding mills.

Jan 1, 2008

By D Chappell

Coromandel Peninsula gold mineralisation has an epithermal style which involves extensive alteration of host rocks and addition of pyrite over large volumes of rock. These altered rocks therefore have high potential for generating acid rock drainage. Natural acid groundwater discharges occur in altered rocks, but not in propylitically altered rock. There is little calcite available in mineralised rocks to neutralise this acid. In contrast, the mesothermal veins of the Otago Schist cause little alteration of the host rock, and that alteration has similar mineralogy to the host rock. Calcite is a common mineral in host and mineralised zones, and sulphides are generally subordinate. Hence acidification of Otago rocks is unlikely. This lack of acidification in Otago facilitates arsenic mobility in solution, up to hundreds of ppm. Arsenic is insoluble under acidic conditions in the Coromandel. Base metals are soluble under acidic conditions of the Coromandel, but they are immobilised by adsorption on to the widespread clay minerals where the solutions are neutralised. Base metals are generally immobile in Otago, but when they are mobilised, adsorption is less effectiveas an attenuation mechanism because clay minerals are rare.

Jan 1, 1998

By Pierre Lacoste-Bouchet, Ian Orford, Mike Cooper

"The Brunswick Mine ore requires fine grinding to achieve liberation of minerals. With 25mm slugs as the grinding media in the ball mill, there was a limitation of a P80 of 25 microns on the CuPb regrind circuit. Results from pilot plant testing showed that the separation efficiency could be increased through fine grinding with a P80 of 15 microns.Options considered were the capital expenditure for new fine grinding equipment such as a vertimill or the use of the present ball mill equipment with smaller media. The Wheelabrator Allevard Enterprise (WAE) millpebs product was chosen because it was a smaller media with a distribution of steel pellets between 5 to 12 mm.With millpebs the grinding product was reduced in size from a P80 of 25 microns to a P80 of less than 19 microns. The power draw to achieve the finer grind was 13% lower while the media consumption was 57% higher.The millpebs grinding media was also tested on the zinc regrind mill. The purpose of the trial was to understand what the media consumption and power draw would be with the charge lowered to achieve an equivalent grind as obtained with the slugs. The media consumption was approximately the same and the power draw was reduced by 30%.INTRODUCTIONThe Brunswick Mine ore is a complex Pb-Zn-Cu-Ag sulphide ore with the grain size of the minerals varying from submicron blebs to particles up to several mm in size. The ore is ground progressively finer in stages. The first step of grinding occurs in the SAG mill circuit. The product sizing 80% passing 95 microns is fed to the CuPb prefloat stage (Cormier et al 2002). The tails from the prefloat is then further ground to a P80 of 35 microns for the CuPb rougher flotation. The final liberation for the CuPb circuit takes place in the CuPb regrind circuit. The regrinding mill further liberates the cleaner scavenger concentrate, second cleaner tails and third cleaner tails. The reasoning for the progressive grinding is to achieve fine grinding without having galena over ground due to its high specific gravity that preferentially sends it to the cyclone underflow."

Jan 1, 2006

By R Zhou, B J. Monaghan, S J Chew, R J. Longbottom, D J. Pinson, H Li, P Zulli, G Zhang, L Lu

Steelmakers are increasingly motivated to use iron ore resources with a wider range of grades and mineral types that were previously considered unsuitable or uneconomical for sintering. In this respect, specific issues, which now require further investigation and understanding, include the sintering of ore types with:- overall higher gangue content- elements that cause problems in the steel manufacturing operations- distinctive sintering performance compared with traditional hematite-rich iron ores. Laboratory-based investigations of the sintering performance and the behaviour of gangue impurities during sintering is an important step towards the successful utilisation of these resources in steelmaking.In terms of laboratory-based sintering investigations, there are two generally accepted experimental scales utilised prior to undertaking industrial-scale trials, which include: bench-scale tablet (compact) testing and pilot-scale pot testing. The former has the advantages of flexibility and more precise control of sintering conditions; but it is difficult to simulate the heterogeneity of a sinter bed. The latter, which is carried out in pots with diameters between 150–500 mm, simulate the commercial sintering process and conditions quite well, but is time-consuming and labour-intensive due to operational complexity. It is therefore desirable to establish a smaller scale pot testing facility that avoids the disadvantages of the normal sintering pot but can provide comparable information.To explore the feasibility of small-scale pot testing, a ‘millipot’ facility was established to examine the sintering performance of iron ores and other non-traditional ferrous materials. The millipot has a diameter of 53 mm and height of 400 mm. The facility has the capability to monitor the sintering temperature at a number of locations (axial, radial) within the sinter bed and to adjust the suction (‘windbox’) pressure. This paper describes the development of the millipot facility and operational procedures, together with initial tests undertaken in order to match its performance with industrial sintering performance.CITATION:Li, H, Zhou, R, Pinson, D J, Zulli, P, Lu, L, Longbottom, R J, Chew, S J, Monaghan, B J and Zhang, G, 2017. A millipot set-up for sintering investigation of iron ores, in Proceedings Iron Ore 2017, pp 85–90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Hemingway P, Boag J

Major operating aspects of the Mary Kathleen Uranium Ltd. treatment plant are discussed with partkular reference to those which are peculiar to this operation.Problems associated with the production of a penalty free uranium oxide product are examined and the methods developed to overcome them are described in detail.INTRODUCTIONMary K,athleen Uranium Ltd. is the largest of the Australian uranium producers. The flow-sheet is based on fine grinding, standard sulphuric acid leach, ion exchange concentration, and magnesia precipitation of the final product, with certain modifications introduced as the result of pilot plant investigations at the South Australian Department of Mines Research Laboratories in Adelaide.The plant commenced operations in June, 1958, attained design tonnlige of 1,120 tons per day in September of that year and has since operated continuously with a throughput in excess of 1,000 tons per day. Pilot plant recommendations generally have been followed, and predicted results have been attained. The only exception has been the silica and rare earth content of the product produced during the early months of operation. Considerable modification of the early resin regeneration techniques resulted in the reduction of the silica content of the product to within specification limits. Research work in the ion exchange section has also resulted in the reduction of the rare earth content of the product to below specification levels. All product now being produced is completely within the agreed specification limits of impurities.

Jan 1, 1961

By D. J. Goodings, R. J. Bonenberger, H. U. Leiste, W. L. Foumey

This paper describes a series of two-dimensional tests conducted and filmed with a high-speed (500 frames per second) video camera. The purpose of these tests was to provide a better understanding of the processes involved in creating craters and channels in water covered soils with explosives.

Jan 1, 2000

By H. T. Ozkahraman

It is important to know the breakage mechanism in materials since this knowledge influences the results of subsequent grinding operations. There are two distinct failure mechanisms in breakage: one is tensile micro crack generation at low stresses, which leads to macroscopic failure by disintegration, and the other is formation of shear zones under heavier dynamic impact forces, which generates more fines as seen in crush zones in blasting. Tensile fracturing simply breaks the material into fragments. It is seen as the disintegration of the specimen into two or more separate fragments. This happens under the absence of lateral stresses and the material is free to expand. On the other hand, compressive-shear breakage produces finer fragments due to shear stresses. The first mechanism is observed in laboratory tensile and bending strength tests and the second mechanism is observed both in laboratory brittleness tests and in situ blasting operations under dynamic impact forces. The friability of rocks and ores can be determined by a brittleness test. A test apparatus to determine the friability value has been designed to suit limestone strength characteristics used in cement production. The friability and stored strain energy values of barite, marble, limestone and bauxite have been determined and compared with the corresponding Bond work index (Wi) and grindability index (G) of these materials. The physico-mechanical properties of the tested materials have also been determined to investigate their effect on friability and grinding. The relationships obtained between the indices were in surprisingly good agreement, with high correlations (0.99 and 0.97). The Bond work index and grindability index can therefore be estimated from the friability value, which can be determined more rapidly than the Bond test. But for certain rock types such as andesites the relationships does not hold. Key words: comminution, tensile stress, shear forces, brittleness test, strain energy.

Jan 1, 2010

By Bill Almdal

Today?s presentation ? Role of the Regional Issues Working Group ? What does RIWG do? ? How can RIWG?s work benefit Stakeholders? ? Review of forecasts vs. reality ? How have past investment compared to the reality? ? Risks to future growth ? The growth potential is very high and so are the risks ? Examples of outputs ? Housing needs ? Growth in population ? Tires for large trucks The Regional Issues Working Group ? Our vision ? To provide a proactive process which promotes the responsible, sustainable development of resources within the Regional Municipality of Wood Buffalo for the benefit of all stakeholders ? What we do ? Facilitate planning for growth ? Facilitate effective and efficient resolution of issues ? Involve all of the resource developers and affected stakeholders in planning ? Develop plans for sharing benefits with Aboriginal stakeholders ? Benefits for Stakeholders ? Our forecasts include up-to-date information from all developers ? including information on employment and housing needs ? Our forecasts are the basis of planning for many stakeholders ? and can assist in their development planning

May 1, 2002

By R Adofo

Underpinning the mining process is a continuum of prediction, specifically of tonnes, grade and recovery from exploration to grade control, through short-term mine design, to mining and processing. The interdependence of one activity on the other is so strong that it can be difficult to partition the activities and determine where there are issues, if any. Reconciliation is the process that compares the predictions of the various estimates to the actual product produced at the end of the production chain. Quite often, an attempt to understand the variances from one measuring point to the other creates a ‘wicked problem’.This study outlines the benefits of incorporating the principles of ‘systems thinking’ into the mining reconciliation process, by constructing a framework within which reconciliation is effectively managed. The philosophical base for any variances between successive links in the reconciliation chain cannot be attributed purely to the statistical variance between the predicted and the actual grades achieved, but should include the interrelationships between the technical and managerial professionals involved. Systems thinking, as an interdisciplinary approach, draws its ideas and concepts from a variety of disciplines, and in so doing can exploit their different strengths.The study described in this paper offers methodologies to analyse the task, in advance of developing a technical solution. Two systems thinking methodologies, Grounded Theory (GT) and Soft Systems Methodology (SSM) were employed. These methodologies, are geared towards dealing with relationships and interactions between individual parts and the whole. The GT coding in the study specified that the key activity that would drive the reconciliation process is through an effective reconciliation meeting, and the competencies of a ‘reconciliation team member’ This team member should be a good communicator and enjoy challenges, be open-minded and transparent, and have a broad perspective of the mining process and relationships across the different activities.CITATION:Adofo, R, 2017. A systemic approach to managing the Mine to Mill reconciliation process, in Proceedings Tenth International Mining Geology Conference 2017, pp 95–102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By S R. La Brooy, T Giraudo, I C. Ritchie

The treatment plant at the Macraes Gold Project in New Zealand processes a carbonaceous, refractory sulphide gold ore. Since its commissioning in 1990, there has been a programme of continuous improvement of the plant, leading to higher recovery, increased throughput and low operating costs. During this time, a number of processes for treating both, or either, the preg-robbing carbonaceous fraction of the ore and the refractory sulfide fraction have been evaluated, trialed and utilised. The latest phase involves the installation by Minproc of plant utilising Newmont Gold's Pressure Oxidation Technology, a process which is anticipated to mitigate both problem factors when commissioned in 1999.

Jan 1, 1998

By Shaoxian Song, Ling Xia, Hongqiang Li, Yubiao Li, Yunliang Zhao, Shaobing Xie

Since human daily demands for fresh water have been increased significantly, the supply of fresh water for the mining industry, especially froth flotation, should be considerably reduced. In addition, stricter environmental standards have been implemented in many countries to reduce the risks due to the disposal of wastewater, many flotation operators have to seek more efficient ways to utilize the limited fresh water sources. Recycling water with high concentrations of impurities is a normal strategy for most of the mineral processing plants; however, water quality should be carefully considered to guarantee a smooth flotation process. Recently, the application of seawater in flotation has attracted much attention due to its availability and abundance rather than fresh water. However, the influencing mechanisms due to the application of seawater in flotation have not been fully understood especially the reactions between mineral particles and bubbles in the presence of high concentrations of cations and anions. This would impede the application of alternatives to fresh water in the flotation. Therefore, this paper reviews the current water sources and the technologies for water recycling in the flotation process. Specifically, the life cycle of water in flotation was proposed. In addition, the strategies including high pulp density flotation as well as the most promising alternatives to fresh water have been discussed in details, with the related mechanisms being demonstrated.