Search Documents

Excavations in rock are commonly supported with wire mesh, shotcrete, wire mesh and shotcrete in combination, and shotcrete reinforced with various types of fibres. Wire rope lacing and various types of straps are additional forms of support installed over the above types, to cope with severe conditions. These support systems are very important items of ?membrane? rock support. With the recent development of several types of thin sprayed linings, the importance of membrane support is likely to increase in the future. In this paper, a wide range of mechanisms of membrane behaviour and mechanisms of loading of membranes, is described. The concepts of membrane components, which are single membranes that may be used on their own as rock support, and membrane systems, which are combinations of more than one membrane component, are introduced. Different situations have different requirements of membrane support, and differences between civil engineering and mining requirements are highlighted. With the different basic requirements in these two areas, the requirements of rock support are correspondingly different. A thorough understanding of the mechanisms of behaviour of the different types of membranes, and the different mechanisms by which the membranes are loaded, is essential before a selection of appropriate support can be made, before appropriate design methods and calculations can be determined, and before appropriate performance test methods for membranes can be defined. The material in this paper contributes towards the understanding of membrane support behaviour.

Jan 1, 2001

By Peter Duniam, Stephen John Brace

2000 HIGH-TECH SEMINAR Blasting Technology, Instrumentation and Explosives Applications Orlando,Florida,USA July24-27,200O. Objectives:- After completing this session 1. Explain safety issues 2. Do simple initiation design 3. Describe how the system works 4. Demonstrate scanning, hookup, testing and firing 5. Describe hot to do a post blast check 6. Explain how to treat misfired detonators

Jan 1, 2000

By Eugie Kabwe

Rock bolts are components of tunnel support structures and their efficacy in reinforcement requires the appropriate estimation of the bolt pre-tension. However, cases of ineffective rock bolt application due to loosening are common which leads to the potential failure of the support structures, thus negatively affecting the tunnel stability. The effective employment of pre-tensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut pre-load. Henceforth, this paper presents a load indicator washer (LIW) capable of withstanding assigned static loading as well as provides an appropriate pre-tension. The different LIW breadths are numerically analysed in the finite element code (ABAQUS) to estimate deformation when a designated 60-kN pre-load is applied. The numerical simulation employs a bi-linear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nutLIW-rock bolt connection. Therefore, a long-term relaxation effect on bolt pre-tension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW-predetermined deformation is the bolt pre-tension. It is drawn from the simulation results that the 1.5-, 2.0-, 3.0-, 3.5-, and 4.0-mm-thick LIWs are completely flattened when subjected to 28-, 42.5-, 65-, 76-, and 88-kN pre-load respectively.

By John R. Benham

The Windigo Theilson RARE II area has a low mineral potential. There are no mines or claims in the area. The only observed results of mining activities were five prospect pits near Tolo Mountain. Samples from these pits contained no significant assays. The study area contains more than 190 million cu yds (145 million m3) of cinders in 17 cones. Development of these cinders is unlikely because their locations are remote, and other sources supply area needs. The Geological Survey has classified the area as prospectively valuable for geothermal resources. However, there has been no geothermal exploration activity.

Jan 1, 1982

By R. W. Parsons

The over-all apparent single-phase permeability of fracture-rock systems was studied using two different two-dimensional models. In a strict sense the results are applicable only to these models, yet may give some insight into real reseruoir behavior. The regular fracture-matrix model can have any number of regular fracture sets. All fractures within each set have the same orientation, width and spacing. The gross behavior is amlytically equivalent to that of an anisotropic permeable medium. In the heterogeneous fracture systems, individual fracture conductivities vary within a two-dinensioml network pattern. A computer program calculates the overall permeability after the conductivities are randomly placed in the network. The calculated permeability depends upon the distribution of these conductivities and the particular fracture pattern into which they are placed. Although detailed information on actual reseruoir fracture systems is not available, this study shows how some of the possible variables may affect obserued gross reservoir characteristics. INTRODUCTION Characteristics of reservoir rocks are determined by direct (core analysis) or indirect (logging and production tests) examination. Both methods, singly and together, are widely used in reservoir evaluations. For fractured reservoirs a problem exists in relating characteristics of cores to the in situ reservoir properties. Knowing fracture characteristics can be of value in determining production mechanisms. Because of the limitations of observation, the intimate details of a fractured rock system will never be known. One approach in analyzing fractures is to study the behavior of some conceptually simple models. The two models analyzed contain features which may be realistic, yet are mathematically tractable. Flow is considered in two dimensions only, with the plane of interest at right angles with the fractures. This concept represents the horizontal flow in a reservoir system with the fractures oriented vertically. Only single-phase, laminar flow is considered. The regular fracture-rock system permeability is calculable from a simple analytical expression. The heterogeneous system requires a computer program for calculating overall permeability.

Jan 1, 1967

By K. V. Phani Prabhakar, G. Padmanabham1, L. Subashini

Laser-arc Hybrid Welding (LAHW) is a relatively recent concept which effectively combines the advantages of laser welding such as the high depth of penetration, low heat input, high welding speed and the positive aspects of arc welding such as better edge bridging and possibility to add filler. For example, steel sections upto 12 mm thickness have been successfully welded in a single pass at a welding speed of 1 m/minute using a 3.5 kW CO2 laser in combination with a MIG arc. Maraging steel of grade M250 is widely used in the aerospace industry in thicknesses upto 10 mm. Conventionally, it is possible to MIG weld such thicknesses in 3-5 passes employing V-Groove joint preparation. However, this multi-pass welding results in formation of reverted austenite in the weld zone after post weld aging; and the high heat input widens the reverted austenite containing heat affected zone which is popularly known as the dark zone/eyebrow zone. Both these zones are detrimental to strength of the welded joint, specifically the fracture toughness. The width of the dark band is an important factor because, thinner the band, it is supported more effectively by the surrounding material. Therefore, in order to avoid multi-pass welding and reduce the overall heat input, single-pass laser-MIG hybrid welding was attempted on 10 mm thick maraging steel M 250 plates using a hybrid laser arc welding system comprising a 3.5 kW CO2 slab laser and a MIG welding system. Simultaneously, multi-pass MIG welds also are produced. Both the laser-MIG hybrid and MIG welds are characterized microstructurally and subjected to mechanical tests such as tensile and fracture toughness in as-welded and post weld aged condition. The amount and distribution of reverted austenite in the fusion zone and width of the dark band was found to be different. Hybrid welds showed a narrow dark band zone and improved mechanical properties. Laser-hybrid and MIG welding investigations carried out on thick section maraging steel M 250 will be presented in detail, including microstructure, tensile properties and fracture toughness of the welds. To the best of the knowledge of the authors there are no reports on laser-MIG hybrid welding of maraging steels.

Jan 1, 2014

By John Nunes, Frank R. Larson

Temperature-dependent functions of various ten-sile flour stress and fracture parameters were investigated on iron and low composition alloys of Fe-C, Fe-Cr, Fe-Mn, and Fe-Ni. Data were obtained over a range of test temperatures from 200" to -196"C at an initial strain rate of 0.01 min". It was found that the strain-hardening exponent, n, for the Fe-Ni alloys increased significantly at very low testing temperatures with increased alloy addition. Also, the stress and strain at fracture followed a predictable transitional type of behavior. The flour stress-temperature dependence was evaluated employing the relation: M where it is shown that composition can strongly influence the constant M. An empirical formula describing this effect is as follows: M = MI (equivalent at. pct Ni)-'" Some preliminay, tests were run on several commercial steels to test the generality of this relationship. One of the phenomenological explanations of the ductile-to-brittle transition encountered in bcc metals is based upon the difference in the temperature dependence of the flow and fracture stresses.' It states simply that the fracture stress is relatively insensitive to temperature and that the yield or flow stress rises rapidly with decreasing temperature so that, when the flow stress reaches the fracture stress, brittle fracture occurs without appreciable plastic deformation. This behavior is illustrated schematically in Fig. 1 where the ductile-to-brittle transition is shown to occur at two possible temperatures. The lowest temperature, TB, represents essentially completely brittle behavior while the higher temperature, TN, represents "notch" brittle behavior. Support for this theory is obtained when it is observed that fcc metals, which do not commonly have a ductile-to-brittle transition, also do not commonly exhibit any strong temperature de- pendence of the yield stress. This relationship of yield or flow stress behavior with the ductile-to-brittle transition has been generally observed for most metals representative of these two crystallo-graphic structures. One exception to this generalization appears in the case of tantalum where no apparent ductile-to-brittle transition has been observed. However, this may simply be an indication that this type of behavior is not directly related to the flow stress and that some other mechanism such as twinning must also be operative. A comparison of the typical temperature dependence of the yield stress of some representative metals is shown in Fig. 2. In the study of the temperature dependence of the strength of metallic materials, considerable ef-

Jan 1, 1963

By Stavros H. Constantopoulos

Mediterranean regions such as Greece, Turkey, Cyprus, Corsica and New Caledonia have experienced epidemics of malignant mesothelioma as a result of non-occupational, ??domestic?? exposure to tremolite asbestos and fibrous erionite. This exposure to tremolite asbestos and fibrous erionite is typified ??domestic?? due to its prevalence in regions with natural deposits of tremolite asbestos (or fibrous erionite) where the material from tremolite asbestos or fibrous erionite is used for domestic applications such as whitewashing. However, these exposures may be useful in examining the potential consequences of even small amounts of amphibole asbestos fibers in the ambient air. It can also elucidate the effects of fibers that behave like amphibole asbestos. However, this type of exposure is not useful for studying the potential effects of small amounts of asbestos in the ambient air of big cities due to the differing nature of the fiber types and modes of exposure between the regions. © 2008 Published by Elsevier Inc. Keywords: Tremolite asbestos; Erionite; Domestic; Environmental; Exposure

Jan 1, 2007

By Gennaro Gerald Marino

Vast improvement in methods of design and analysis of the long- term stability of overburden above room and pillar mines is needed. Improved methods are vital for planning and land development and for prediction above existing, presently stable, room and pillar mines. As shown on the flow chart in [Figure 1], the assessment of the long-term stability is an integral part of the site investigation process regarding mitigation of surface damage effects. In Illinois, flat farmlands with subjacent coal reserves cover vast areas. In some of these areas high extraction of the underlying coal layer(s) may not be possible since the resulting surf ace subsidence combined with a pre-existing shallow water table would make the land too wet. Thus recovery of this coal might only be accomplished by room and pillar mining where the ground surface does not subside and the hydraulics of the overburden are not significantly affected.

Jan 1, 1986

By A. L. Garassino

Dans cet article on parle sortout de l'approche de calcule pour les pieux charges horizontalement avec particuliere reference aux curbes p-y et è une solution semi-empirique qui prende en consideration les variations typiques du module du sol avec la deformation obtenue par les données expérimentales. 1. INTRODUCTION The analysis of the piles under lateral loads depends very strictly from the pile stiffness and geometry, from the soil type and from the strain field. Different approaches were adopted in solving the problem. Some Authors developed methods for estimating the ultimate lateral resistance of piles and pile groups by conventional static approaches, as the Brom's widely known (1964) or by the plane strain solution developed by Davis (1961) or by empirical engineering con­siderations l

Jan 1, 1994

By D. Ksinsik, R. Boisvert, D. Leblanc

Casting, cooling and crushing/sieving of ferroalloys has followed a well-established pattern in the whole ferroalloys industry for many years. Usually liquid metal or alloys are cast into flat open moulds of various shapes and forms, and after solidification the product is removed from such mould to further cool down to a temperature where subsequent handling steps are feasible. Common to all mechanical product fractioning is the generation of dust and fine size material with lower product value. For almost 10 years, Bécancour Silicon has investigated alternative roads to improve technology and/or reduce or solve problems related to those disadvantages. Since 1995 Bécancour Silicon operates a special silicon granulation plant targeted to product for the chemical treatment/conversion of silicon for silicones production. Prior to the development of the granulation process, various systems had been evaluated, among others the vibrating casting bed, now in operation elsewhere but judged inappropriate because of the tapping volumes to be handled at Bécancour Silicon and other disadvantages. After evaluation of all aspects of heat transfer, radiation, and conductivity in relation to transfer media and within the product, a novel system was designed and built.

Jan 1, 2004

By B. Tiryaki, O. Z. Hekimoglu

Shearer drums are a critical component in the overall performance of coal shearers, with the cutting performance depending very much on the disposition of cutter tools on the drums (the tool-lacing arrangement). A series of practical and theoretical studies has been undertaken to investigate aspects of shearer drum vibration in terms of circumferential pick spacing. A number of commercially available drums were redesigned and the lacing patterns compared with those of the original drums under near-uniform conditions. Mine trials were carried out at the Middle Anatolian lignite mine in Turkey with drums fitted on Eickhoff type EDW-230 double-ranging drum shearers. It was found that the performance of drums could be improved if the concept of circumferential pick spacing was taken into account in CAD packages along with the existing design parameters such as cutting rate, reduced dust, low pick consumption and low down-time

Jun 19, 1905

By M Donghi, G Ramage, A Barnes

As the mining landscape continues to transform, the challenge of accessing deeper orebodies quickly and safely is becoming a frequent topic of conversation amongst those in the mining industry. The rapid development of underground mine entries to gain earlier access to deeper orebodies is an ever-present challenge to mine owners and contractors. Overcoming this and providing economical solutions to unlock the value in these deeper deposits is a challenge that should be confronted.In 2013, Redpath Australia Pty Ltd (Redpath) commenced construction of what would be the first of two drifts excavated through the use of a tunnel boring machine (TBM) in Queensland’s Bowen Basin.The excavation and development of the two drifts (declines) was completed as part of a contract for underground mining services between Redpath and Anglo American at the Grosvenor Coal Mine Project in Central Queensland, located approximately 5 km north of the town of Moranbah. Having recently completed the drift development, this paper will extend on the early writings of Donnelly, Ramage and Donghi (2014) and provide detail on the operational achievements, advance rates, threats, opportunities and learnings during the excavation of the two declines: the conveyor (CV) drift and the transport (M&M) drift.CITATION:Ramage, G, Donghi, M and Barnes, A, 2016. Experiences gained through tunnel boring machine decline development, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 695–712 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M. G. Zabetakis, T. D. Moore

The use of a partially slotted 6.5-inch-inside-diameter vertical pipe to remove methane from a longwall gob area at a depth of 2,260 feet in the Pocahontas No. 3 coalbed ms investigated. The value of gas removed by such a pipe under free-flow conditions was found to equal the cost of the installation in this case. Approximately 25 percent of the available methane passed through the pipe without the use of an exhauster; an additional 10 percent was removed when an exhauster was employed. The diversion of methane through a vertical slotted pipe to the surface permitted the use of increased mining rates and decreased the ventilation air requirements.

Jan 1, 1972

SOME notes on the works of the Electrolytic Refining and Smelting Company of Australia will no doubt be of interest to members of the Institute, more especially as much of the work is new to Australasia. As many of the members who may read this paper have not been in a position to visit works of this kind, and are consequently not thoroughly acquainted with all the operations carried on, the author has taken the liberty, in some cases, to enter into explanation which would otherwise be unnecessary. The works are situated at Port Kembla (New South Wales), about fifty miles south of Sydney, and are approachable both by rail and water. The Government has recently built a low-level jetty upwards of five hundred feet long, and intends installing at an early date an electrically operated portable crane to facilitate the handling of material to and from the boats. This will mean: a considerable reduction in the length of time that boats are laid up at the jetty. There are also under construction two breakwaters, which, when complete, will materially assist shipping operation...

Jan 1, 1910

By Teale E. O

The purpose of the present communication is to put on record the discovery, in October, 1916, in the Howqua district, of a new locality for the occurrence of phosphatic rocks in Victoria, and to give a preliminary description of its characters and geological occurrence. Owing to the great use of superphosphates for agricultural purposes in recent years in Australia, search has been stimulated for the discovery of local and workable supplies of phosphatic rocks. Phosphorus is an element very widely distributed in igneous rocks, usually in the form of the mineral apatite, and also occurs in sedimentary rocks and in soils as a detrital constituent. Under these conditions of occurrence, however, the amount of P 205 present in a rock or soil seldom approaches, and very rarely exceeds, 1 %. Very occasionally it occurs in such a concentrated form as to constitute workable deposits. In such cases they are usually of organic origin. Sometimes they occur as geologically recent deposits of guano or rock...

Jan 1, 1918

A201 aluminium alloy is a high strength casting alloy with a nominal composition of Al-4.6Cu-0.3Mg-0.6Ag. It is strengthened by the O(Al2Cu) phase and the ??(Al2Cu) phase during heat treatment. Further strengthening of this alloy system can be obtained through the addition of transition elements, but care must be taken as other elements might have adverse effects on the mechanical properties. The objective of this study is to determine the influence of Mn on the tensile properties of rheo-processed Al-Cu-Mg-Ag alloy A201. ThermoCalc software was used to predict the different phases that can be expected in the alloys, and scanning electron microscopy(SEM) with energy dispersive spectroscopy (EDS) was used to investigate the actual phases that formed. The influence of these phases on tensile properties is quantified. SEM and ThermoCalc revealed that there is an increased amount of the Al20Cu2Mn3 with increasing Mn. The tensile properties showed that high amounts of Mn do have adverse effects on the tensile properties of alloy A201, especially the ductility. Keywords Semi-solid metal (SSM) forming, alloy A201, intermetallics, Al20Cu2Mn3

Jan 1, 2011

By Gray Mullins

This paper presents experimental results from a study to assess the interface bond between a cast-in-place concrete seal slab and prestressed concrete piles in cofferdams. Three different seal slab placement conditions - fresh water, salt water and bentonite slurry - were evaluated and the results compared against controls where no fluid had to be displaced by the concrete. Normal pile surfaces were investigated. Additionally, the situation of ?soil caked? piles was also investigated. Both model and full-scale tests were conducted. In the model tests, twenty eight 15 cm square prestressed sections were used with the embedment depth varied between d-2d, where d is the width of the pile. In the full-scale tests, 16 specimens were tested. The prestressed piles were 36 cm square with the embedment varied between 0.5d-2d. Four of the sixteen piles were cast with embedded gages located at the top, middle and bottom of the interface region. The results showed that loads were transferred to the piles over an effective area, not the entire embedded depth. Significant bond stresses developed even for the worst placement condition. Recommendations are made for revising current values in specifications.

Jan 1, 2013

By C Spandler, S W. Richards G Rosenbaum, R J. Holm

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.The recent and active magmatic arcs of eastern Papua New Guinea (PNG) and the Solomon Islands are well endowed with sulfide mineralisation and include deposits such as Ladolam, Panguna and Solwara 1. The majority of the mineral systems in this belt are younger than four million years old, with some deposits remaining active to the present day as exemplified by active hydrothermal systems on the island of Lihir. The geodynamic setting that led to the formation of these deposits is still unresolved, with, for example, both the Pacific and Solomon Sea plates considered responsible for the formation of the Ladolam deposit on the island of Lihir under different models. In order to understand and characterise the formation of south-west Pacific mineral deposits, we must first reconstruct the complex geodynamic evolution of the region. New kinematic reconstructions show that while mineral systems in eastern PNG and the Solomon Islands are hosted within a single arc related to subduction at the New Britain and San Cristobal trenches, variable and discrete geodynamic settings exist within both the upper and lower plates throughout this region, which give rise to distinct mineralised corridors. Most notably, this region is host to: the Solwara 1 deposit, which occurs within a major transtensional corridor in the eastern Bismarck Sea the Ladolam deposit (Lihir), which is interpreted to have formed above but in relation to tearing of the subducting slab the Panguna deposit, which is related to structure in the subducting slab marginal to the actively spreading Woodlark Basin.An evaluation of the nature and variability of these diverse geodynamic settings through time can provide us with a better understanding of the relationship between the active south-west Pacific magmatic arcs and mineral deposit formation. It may also provide insights into the diverse array of deposit settings at ancient convergent margins, with applications in mineral prospectivity studies.CITATION:Holm, R J, Richards, S W, Rosenbaum, G and Spandler, C, 2015. Disparate tectonic settings for mineralisation in an active arc, eastern Papua New Guinea and the Solomon Islands, in Proceedings PACRIM 2015 Congress, pp 165–170 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Marc C. Bétournay

A mine production locomotive, the world?s first applied industrial fuelcell vehicle, has been designed and tested in the context of a number of proof-of-concept projects supported by the Fuelcell Propulsion Institute, an international consortium of stakeholders dedicated to facilitate the commercialization of fuelcell vehicles. The locomotive?s simple electric-powered motor and controller system was ideal to study a number of requirements related to fuelcell power application: hydrogen power plant operation, underground hydrogen use, risk and regulatory requirements, production performance versus the conventional battery-powered locomotive version under measured duty cycles and production requirements, power plant design improvements for other fuelcell vehicles, and cost-benefit aspects. This article will focus on the design and testing aspects of this project which has led to successful performance demonstrations of the vehicle under surface and underground conditions at two mines. It will also present information on the creation of a safe, reliable and efficient power plant which fulfilled its design objectives, including longer productivity time for a given vehicle fill-up.

May 1, 2003