Search Documents

A substantial proportion of current and historic West Coast gold production comes from deposits situated around the margins of æice ageÆ glaciers. Gold has been eroded and transported by glacial ice then deposited in till and outwash gravel. The interplay between fluvial and glacial processes, climate, basement geology, tectonic uplift, sediment supply and sea level dictates many aspects of the development of the West Coast landscape. The way in which the external forcing factors interact is crucial in determining the gold content of placer deposits in this region. The following is an outline of some of the factors that influence the gold distribution in vicinity of glacial margins.

Jan 1, 2000

By Rayner B

Five wells have been drilled in the Basker/Manta Block of VIC/P19, Gippsland Basin, resulting in sub-economic Intra-Latrobe Group oil and gas discoveries at Basker-1 and Manta-1. A total of 21 individual hydrocarbon bearing sandstones were intersected by the two wells. These reservoir sand bodies were deposited by fluvial processes in a lower coastal plain environment. The modelling of sand body orientation and geometry is a critical component in the evaluation of the two accumulations. Seismic resolution of the thin (average 2 m to 5 m) sand bodies is inadequate for mapping their orientation and distribution. Dipmeter data has been successfully applied to the problem of orienting the sand bodies using FMS images acquired during the drilling of Gummy-1 and reprocessed HDT data from Basker-1 and Manta-1. Prediction of lateral extensiveness (geometry) of individual sand bodies has also been attempted. Interpreted palaeocurrent direction from all three wells is dominantly from the NW to the SE. Reservoirs in the Manta-1/Gummy-1 area are interpreted to be predominantly channel sands, deposited by relatively low sinuosity streams. As such they would tend to have a laterally extensive, elongate geometry. Sand bodies deposited in the Basker-1 area show a predominance of laterally accreted cycles deposited by meandering streams. Channel geometry may then be limited in the downstream/upstream direction by internal permeability barriers such as clay plugs.

Jan 1, 1992

By M. Lombardero, J. Garcia-Guinea, J. Taboada, B. W. Roberts

The structural, textural and mineralogical properties of the slate formations of NW Spain make it the most important district in the world for quarrying roofing slates. Over the past 10 years the introduction of new methods has increased yields from 2 to 13%. The main factors affecting quality are quartz grain size less than 75 micrometres, homogeneity of slaty cleavage and S0-S1 intersection angle, very low metamorphic grade, absence of secondary foliation, beds 10-12 m thick and low content of oxidisable Fe sulphides. The two main controls on fissility are lithology and deformation accompanied by metamorphism. The minimum natural block size should be 0.6 m3 but this volume can be reduced for modern cutting tools such as diamond wire, chain and circular saws. Structural analysis is crucial in exploration and quarrying, as shown by the prospecting methodology applied at Dominio de Truchas in central Spain and the computer analysis of rock mass discontinuities at Casaio quarry

Jun 19, 1905

By Yael Miron

This report describes laboratory studies by the U.S. Bureau of Mines to determine the suitability of a static oxygen (OJ adsorption test for evaluating the self-heating tendencies of coals. Reliable minimum self-heating temperature (SHT) values from adiabatic oven tests were used as standards for comparison and evaluation. A suite of six coals was tested in the adiabatic oven and in sealed flasks. In the latter tests, both undried and dried samples, in a range of four particle sizes, were examined. Miniature pressure trans-ducers monitored pressures in the flasks, and gas samples taken at the end of the tests quantified all the gases present. An excellent correlation was found between the minimum SHT's and amounts of O2 adsorbed over a 7-day period for dried coals, independent of particle size. In addition, a good correlation was obtained between the minimum SHT's and pressure changes in the flasks at the end of the test for the same coals, also independent of particle size. Based on these results, the sealed flask test can be reliably used to determine the self-heating tendency of a bituminous coal sample.

Jan 1, 1990

Paper presented at the UK minerals industry conference and published in: Minerals extraction towards the millennium. UK minerals industry conference, 3-5 April 1995, University of Leeds. London: Institution of Mining and Metallurgy, 1995. The various types of risks that arise in minerals industry projects are usually financial, technical, or environmental, and the key to valid risk analysis is complete integration of all risks, both within and between categories. Geographical information systems (GIS) and geostatistical simulation methods can provide a means of integrating data and conducting realistic risk analyses. Risk can be quantified but there are limitations to numerical approaches to risk assessment. Realistic quantification requires adequate models of the processes that give rise to risk. Risk perception must also be taken into account when conducting risk assessment and reporting the results, especially in public forums. The modelling and visualisation capabilities of a combined GIS/simulation system can provide the means of dealing with perception in risk analysis

Jun 19, 1905

By K. N. Karparov

The classical limit equilibrium methods are suspected to be ineffective in predicting the potential for highwall failure in many instances in coal mines around the world. Slope engineers have for many years recognized a block thrust failure mechanism for slope failures, but little work had been done before 2000 to explain the actual mechanisms which must be responsible for the failure. The main reason for this is that limit equilibrium methods implicitly assume rigid blocks, and the resulting force equations must be satisfied everywhere simultaneously for them to have any meaning. This paper will show that the material involved in the slope failure is not rigid; indeed it undergoes considerable permanent deformation during failure. This observation allows the authors to treat the block boundaries independently, because they need not maintain a constant spatial relationship with one another, as is assumed in other methods. To enable analysis of this type the authors assume that the weight of the blocks is evenly distributed. This is reasonable, because the slope material is not strong enough to be self-supporting without some sort of constraint, or strong enough to be able to apply point loads to the surrounding material. The purpose of this paper is to extend the practical application of the analytical method developed from mechanism studies to provide an objective assessment of the risk of slope failure, and therefore guidelines for more stable slope designs. This work is based on studies carried out on two failures in an open pit coal mine in South Africa, and provides a methodology to assess the potential for failure more objectively than is possible with currently accepted methods, while at the same time remaining sufficiently simple to allow a ?back of the cigarette box? assessment by geotechnical engineers on site.

Jan 1, 2009

By Napisporn Memongkol

Syntheses of Al-TiC-Al2O3 and Al-SiC-Al2O3 composites were obtained in situ by carbothermal reduction of mixtures of Al powder, TiO2 powder and activated carbon powders and Al powder, SiO2 powder and activated carbon powders. The reductions were carried out in a horizontal tube furnace under flow of inert gas. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The synthesized products were mixtures of aluminum reinforce with titanium carbide and alumina and aluminum reinforce with silicon carbide and alumina. The effect of the reaction temperature (1000 o C ? 1200 o C) and condition of precursors on the Al powder, TiO2 powder and activated carbon powders and Al powder, SiO2 powder and activated carbon powders were investigated using XRD and SEM method. The synthesized products showed those composites with aluminum matrix and titanium carbide and alumina as reinforced phases and aluminum matrix and silicon carbide and alumina as a reinforced phase was formed.

Jan 1, 2006

"The mining industry uses many types of mineral and metallurgical plants to produce saleable product from ore mined. Plant design history has left current operations with a mixture of manual operation and various forms of automated process controls. Consequently, we typically see high variability in the continuous operations together with a shortfall in the attainment of full capacity, or higher utilisation of consumables.At a level of best practice, ‘Operational Performance Excellence’ focuses on process control, using automation and control systems to deliver process optimisation. This more sophisticated delivery is a great deal more difficult than the first stage of equipment selection / installation. It includes the appropriate selection of the right instrumentation, control system, key process knowledge, individuals with a solid control engineering background / experience, and the essential backing / support of the operations management team together leading to higher value delivery. Robust solutions can be realised, considerably minimising process variation, thus leading to process optimisation. This approach results in an easier, efficient and safer process while providing considerable returns for the plant owners.How variable are your processes, and do you maintain optimised process performance with dedicated resources, modern instrumentation, ‘best practice’ control systems and performance monitoring tools? In this paper, these questions and their possible answers are discussed."

Jan 1, 2014

By R. Patel, D. R. Taylor, P. M. Varley

In-situ measurements of ground stress were made from surface boreholes, using overcoring and hydrofracturing techniques, to obtain data for the detailed design of the underground works at Pergau. Unexpectedly low stresses were measured and appeared to correlate with apparent hydrofracturing observed during permeability testing. The low values of the minor principal stress had a major impact on design, particularly of the lining for the pressure tunnel and shaft. Additional hydrofracture tests were made underground during construction of the low- and high-pressure headrace tunnels and the pressure shaft, to define the vertical reduction in the minor principal stress with overburden. These data were then used to locate and design the steel and reinforced concrete linings

Jun 19, 1905

By A. C. Fieldner

"Decline of the Beehive Coke OvenTwenty years ago a favorite theme of the crusader for fuel conservation was the enormous waste of valuable by-products incurred in the manufacture of blast-furnace coke in beehive ovens. Indeed, there was good reason for arousing the national conscience to this needless' loss of an irreplaceable mineral resource. In 1910, 83 per cent of the coke production was made in beehive ovens, from which surplus gas, tar, light oil, and ammonia, aggregating in value (at 1910 prices) 40 million dollars annually, were discharged into the atmosphere.In 1929, proportions were reversed and 90 per cent of the production was made in by-product ovens. The average value of by-products obtained in the production of 1 ton of coke in 1929 was $3.60, as compared with $1.16 in 1910, although the value of a ton of coke had increased only from $3.47 to $4.80. As shown in Figure 1,1 the production of by-product coke progressed rather slowly until 1915. War needs suddenly expanded the demand for coke and the by-products benzol and toluol for the manufacture of explosives. Except during the depression of 1921, this accelerating rate of production was maintained up to 1929, largely at the expense of beehive plants. The 1929 production of 60 million tons of coke will probably remain a record-breaking figure for several years. The developments which are now in progress in long-distance transmission of rural gas and in the utilization of volatile petroleum products and refinery gases for augmenting, city gas supplies may retard an other- wise accelerating demand for coke and coke-oven gas for domestic and industrial heating, Trends in Value of By-ProductsThe increasing value of by-products in comparison to the value of coke is shown in Figure 2. In 1913, the average value of by-product coke was $3.38, the value of the by-products per ton of coke was $1.41, and the cost of coal per ton of coke was $3,27, In 1929 not shown in figure) the value of the coke had risen to $4.80 per ton, the value of the by-products to $3.60, and the cost of coal per ton of coke to $5.07. The by-product values in were 155 per cent higher than in 1913, although the coke value had increased only 25 per And the cost of the coal 55 per cent. Actually the increase or the total value of coke plus by-products in this period was very little more than the increase in the coat of the coal, being 55per cent for coal and 60 per cent for coke plus by-products."

Mar 1, 1931

By B. A. Ridolfi, S. M. Alvarez

The Moon Creek Reclamation Project provides a case study in the development of creative cleanup solutions for an abandoned lead and zinc mine and mill site located in northern Idaho. Innovative design features include construction of a 88,000cubic yard combined waste containment facility on soft in-situ tailings, water-balance cap, limestone gravel drains, a geocell mattress for stability, and a below-grade scour protection berm. The stream, including a wetlands buffer, will be relocated within an existing road alignment and rehabilitated to provide trout habitat. These elements allow for the integration of reclamation and stabilization measures into an effective site design.

Jan 1, 1999

By E. C. Perkins

As part of a program for developing methods of using domestic titanium deposits, the Bureau of Mines investigated methods for chlorinating titanium slags prepared from titaniferous minerals by electrosmelting. Titaniferous slags were made from ilmenites in the following deposits: Valley County, Idaho; Trail Ridge, Fla.; Aiken, S. C.; and Maclntyre, N. Y.; titaniferous magnetite from Iron Mountain, Wyo., were also evaluated. The tests were made in two chlorinators, a 4-inch and a 36-inch unit. Preliminary testing was done in a 40-millimeter bench-type unit. Chlorine gas was contacted with a loose mixture of titaniferous slag and carbon at a high temperature to form titanium tetrachloride. The moving-bed system used in this work involved a downward movement of feed countercurrent to the chlorine flow, and residues continuously removed from the bottom of the reactor. The performance characteristics of these slags depended on their composition, which varied widely according to the geographic source of the ore. The results showed that all but two of the slags could be chlorinated as effectively as rutile, converting 70 to 80 percent of the titanium to the tetra-, chloride. The two slags that proved difficult were made from New York ilmenite and Wyoming titaniferous magnetite. These slags contained enough magnesium to cause clinkering, which necessitated that the bed be prematurely withdrawn before more than 70 percent of it could react. The iron content of the slags did not interfere with operating the chlorinators. The data from the 4-inch and the 36-inch units were in agreement on the relative amenability of the slags to chlorination.

Jan 1, 1962

By T. B. Colman

Paper presented at the MEP '89 conference held in Madrid, 13-15 November 1989. Britain has sustained an important metalliferous mining industry over many centuries. Recently, new geological concepts and exploration techniques have indicated that there is considerable potential for the discovery of a variety of deposit styles, often in previously neglected areas. The recent discoveries at Aberfeldy (Ba-Zn-Pb), Gairloch (Cu-Zn) and Cononish (Au-Ag)in Scotland and Curraghinalt (Au-Ag) and Lack (Au-Ag-Pb) in Northern Ireland are illustrations of this potential. Some of the prospective areas for future exploration are described and an indication is given of the legislative framework within which mineral exploration and development are carried out

Jan 1, 1991

The object of this paper is to give a description of the new office and changehouse building and equipment at the Zinc Corporation Limited, the office section of which has now been in full use for approximately three years, and the changehouse section for approximately two years. As the expectations of the design have been fully realized, it is thought that this description will be of interest to members and possibly of some use to others faced with similar problems.GENERALIn the centralization of the surface plant around the new main shaft the combined office and changehouse building forms a prominent feature, being located between the shaft and the mill and facing the workshops on the northern side.The scheme for housing all employees in one building was proposed by the Manager, Mr. A. J. Keast, who was familiar with a similar successful structure built at the McIntyre Porcupine Mines Ltd. in Ontario, Canada.The principal features of this building were adopted as a basis for design, and the present layout evolved to suit the particular requirements of this mine.Some of the advantages of the design are:(a) Economy in first cost and space occupied when compared with plants having separate office and changehouse buildings.(b) Easier and more constant supervision of employees and of the plant by the senior staff members.(c) Close contact between officials of all departments.(d) Close covered connection between changehouse and shaft.(e) Avoidance of duplication of ,essential services such as electric power, water, heating plant, sewerage, etc.The Managing Director, Mr. W. S. Robinson, further instructed that the following requirements be adhered to in the new building:(a) Ample accommodation to be provided for office staff and other employees.(b) Special attention to be paid to lighting, both natural and artificial.(c) Working temperatures to be controlled to facilitate comfort and efficiency.(d) The buildings and equipment' to be of a permanent nature with furnishings and fittings of modern design.

Jan 1, 1941

By A. Moergeli

The Swiss are currently building the world’s longest tunnel, the 35-mile long Gotthard Base Tunnel. At Sedrun, for the first time in tunneling, four Roadway Support Machines will drive through most difficult ground, supporting variable diameters of up to 13 m. The machines are prepared for their first deployment. At Amsteg, two Hard Rock TBMs have successfully crossed a known fault zone by applying full circle steel arches and shotcrete immediately behind the cutter head. Comparisons between Drill& Blast and Hard Rock TBM are shown.

Jan 1, 2005

By A. C. Apling, N. B. Barrett

Roadstone production requires the generation of non-flaky material, as outlined in British Standard 812 section 105.1; with respect to this criterion, a mathematical model of a cone crusher must be able to predict the flakiness index of a particular size range as determined by the relationship between thickness and nominal size. The Whiten cone crusher model utilises breakage and classification functions to predict a product particle size distribution only, so a shape function has been proposed that is based on a phenomenological approach, taking into account the transfer between flaky and non-flaky material at each stage of breakage. The results of laboratory tests to determine material breakage characteristics and of examination of pilot-scale test products illustrate the method's potential

Apr 1, 1995

By Ray H. S, Galgali R. K

It is well accepted that the blast furnace will continue as the main route for iron-making for many more years. However, its limitations have motivated researchers to look for alternative routes, particularly, those where non-coking coal is used for liquid iron production. Smelting reduction (SR), where coal and oxygen are used to produce liquid iron and power is now receiving serious attention. Several smelting reduction reactors are now operating in pilot plant scale and one or two have reached commercial status.

Jan 1, 1999

By G. L. Oldwright, F. K. Shelton, W. E. Keck

"INTRODUCTION Zinc must be of high grade to satisfy the present demand. Even when the amount of premium paid is small, the purer metal as the buyers' preference. The following specifications for spelter were taken from the American Society for Testing Materials for 1927, Part I, pane 524. (The specifications for 1930, p. 582, are tile same.)Another specification for zinc of a much higher grade than any of the above has been established lately by the same society. The committee on zinc die-casting (Proc. Am. Soc. Test. Mat., vol. 31, 1931, p. 263) reached the following, conclusions: I. ""That the purest of zinc is necessary to produce stable zinc-base die castings, and as a result requested specifications for zinc spelter .with total impurities not over 0.02 percent."" Their tests showed that the die castings made of the purest zinc had the least elongation and the greatest tensile strength, and exhibited the least changes with temperature.Still more far-reaching claims are made for the properties of zinc containing over 99.99 percent metal. Zinc foil, for instance, may someday be made as a common commercial product. It would seem likely that the demand for zinc of high grades rill continue and that even purer varieties may be desired. This demand fits in with the modern trend in manufacturing plants of reducing the number of variables to a minimum by using pure materials, and of controlling the processing of metals during their various stages of fabrication by mechanical means instead of by expert laborers."

Jun 1, 1933

By G. S. Rice, H. O. Howarth, Greenwald. H. P.

"Electricity as a means of transmitting power was introduced in coal mines of the United States about 1891 for both haulage and coal cutting, only a few years after electrical haulage was first installed on street cars. At first, the hazards of electrical ignition ere not appreciated and the general use of open lights and black blasting powder made the possibility of electrical ignition of fire damp seem small by comparison.5 The possibility of igniting coal dust directly by electric sparks or arcs had not been considered.In the nine years prior to 1900, the progress of introducing electricity underground was slow, except that it was used for lighting shaft bottoms. Electricity had to contend with the more general use of compressed air for coal-cutting machines and, in mainline haulage, with the use of mule-teams and endless and tail-rope systems. During this period, great improvements were made in electrical apparatus, in surface installations as well as in mines. By 1900, therefore, the technique of applying electricity in mines had so far developed that it rapidly drove out the use of compressed air in coal mines because of the comparative ease of its installation and the marked economic advantages of its use over that of compressed air in practically all kinds of mining machines except percussion. rock drills.At this time, however, little thought was given to the hazard of indiscriminate use of electricity causing explosions and fires, and the possibility of electricity causing direct ignition of coal dust had not been considered. On December6, 1907, however, the Monongah, West Va. mine explosion occurred. This was the greatest mine disaster this country has over had, 361 men being killed. Although: there was much diversity of opinion, as to the origin of the explosion, many well-informed engineers concluded that the cause was ignition of coal dust do to wreckage of a runaway trip in a rope haulage entrance slope. This slope also served as a ventilating and it extended from the level of the coal bed to the surface. The runaway trip tore down electric cables and stirred up a cloud of dust when it was wrecked at the bottom of the slope. The dust was probably ignited by the electric arcing that occurred when the wires were knocked down. (Another but less probable source of ignition was the open flames of miners lamps.) From the foot of the slops the explosion appeared to have travelled into the mine, spreading as it went. If this ignition of coal dust was the origin of the explosion, it occurred on pure intake air entering directly from the surface."

Oct 1, 1930

By Clyde N. Baker

Foundations for the Sohio Corporate Headquarters in downtown Cleveland have column loads of 11,400 kips, which increase to 15,000 kips with wind loading. An extensive exploratory program was conducted and comprehensive studies made to select the economically dependable support for the 46-story structure. A test on bond or socket friction for the caissons has usable values.

Jan 1, 1984