Search Documents

By A. Eccles

Phase designs are the foundation upon which all open pit mine sequence optimizations and budgets should be built. Unfortunately, at times, mine engineers skip the step of developing realistic pit phase designs - designs that include access ramps and mineable widths. Without mineable phase designs, their optimized schedules are based on theoretical pit shells or ?quick-and-dirty? plans with no ramps. The output from such optimizations is almost always overly optimistic. Without mineable designs, the production estimates are misleading, because they overestimate ore, and underestimate waste stripping requirements. Worse yet, when plans are not based on realistic phase designs, they can point to exactly the wrong decision in feasibility studies (i.e. ?go? when it should be ?no-go?). This paper discusses the importance and features of good pit phase design, and demonstrates the pitfalls of relying on optimized production sequences that are not based on properly designed pit phases.

Feb 27, 2013

By Harry Schnabel

A 6200 m² cement deep soil mixed (CDSM) wall was constructed for an addition to the Museum of Fine Arts in Boston, Massachusetts. The addition was located along the east side of the existing museum within an existing courtyard and in the area of a recently demolished structure. The basement for the new addition extended up to 9.1 m below the floor slabs of the adjacent buildings. The adjacent buildings are supported on a variety of foundations including; shallow spread footings on alluvial sand deposits, low capacity piles bearing in the alluvial sands and Boston blue clay, and caissons bearing on the alluvial sands and clay. Groundwater was less than one meter below the top of the CDSM wall. The new addition was founded on shallow foundations in the desiccated crust of the Boston Blue Clay. The CDSM wall was selected as the most economical means to control deep seated ground movements, limit movements of adjacent structures, and inhibit groundwater flow into the excavation. Braces and a continuous wale were used to support the CDSM wall where it was located adjacent to structures. Tiebacks were used where there were no structures. Other geotechnical construction at the site included: ? Jet grouting (JG) to improve the ground and provide an impervious subgrade layer at the west end of the addition, ? Concrete pier underpinning was used to support an existing structure on the west end of the site, and ? A secant pile wall using alternating drilled shafts and jet grout columns was used for earth support and a barrier to groundwater flow to allow for the installation of a storage tank at the south end of the site. Inclinometers, total station surveying, vibrating wire strain gauges on the braces and wales and load cells on the tiebacks were used to monitor performance of the excavation support system. The excavation support system performed better than required limiting lateral movements of the adjacent structures to less than 13 mm and vertical settlement to less than 8 mm. No settlements or movement were detected during the construction of the wall. Lateral movement of the CDSM wall was typically below 15 mm with the maximum movement occurring near subgrade.

Jan 1, 2011

By J. E. Sepulveda, R. Morrow

"In full scale mineral grinding operations, the steel balls normally utilized as auxiliary grinding media get to be consumed at different specific rates, as determined by 3 basic mechanisms: abrasion/corrosion (wear), impact ball breakage and impact surface spalling, the latter relating to the removal of rather small pieces of steel coming off the exposed surface of the balls due to repetitive impact with other balls in the charge or the surrounding mill liners. In conventional ball milling applications, the clearly predominant mechanism is gradual wear by abrasion/corrosion. In the case of SAG mills, where the make-up balls may be as large as 6”f diameter, breakage and spalling mechanisms are significant contributors to total ball consumption, although not to the extent of overriding wear mechanisms.Ball wear has been well characterized by the Linear Wear Theory, as presented at the last CMP 2014. Impact breakage has been customarily monitored, at the ball manufacturing site, via Drop Ball Tests (DBT) consisting of repeatedly dropping balls from a standard height and accounting for the number of broken balls and the weight loss (spalling) of the remaining unbroken balls. When properly conducted, DBT’s should provide meaningful indications of the breakage and spalling resistance of large diameter balls. The current publication is focused on the interpretation and projection of DBT results to full industrial scale, taking into account all 3 mechanisms of grinding media consumption in SAG mills.INTRODUCTIONA thorough, quantitative understanding of the independent contribution of all active grinding media consumption mechanisms is of the highest practical relevance, particularly in semiautogenous (SAG) milling operations where ball breakage and spalling can not be ignored or neglected, as it has been normally acceptable for conventional ball milling processes. The high severity impact conditions currently imposed in typical SAG mill environments create serious challenges to the manufacturers and suppliers of large diameter (5”–6”) SAG balls, whose products must be capable of surviving such harsh operational conditions with minimum breakage or spalling."

Jan 1, 2015

Nickel-bearing ores in North-east Dundas have been described by A. McIntosh Reid1 as occurring at the margins of narrow dykes of gabbro, norite, peridodite and pyroxenite, which are intrusive into the Dundas series of slates, quartzites and breccias. They occur chiefly in the neighbourhood of the Five Mile, near Zeehan, as small, narrow ore-bodies which are mostly less than 100 ft. in length.The ores are massive sulphides containing pyrrhotite, chalcopyrite, pyrite and the nickel sulphide, pentlabdite.A less common nickel-bearing mineral, gersdorffite, has been recently found in an adit, which is marked on Reid's geological plan of Dundas as the Hecla mine, 30 chains south of the crossing of the North-east Dundas tramway, over the Great Northern Creek, and at an, elevation of about 350 ft. above the tramway. The occurrence is in a lode traversing the Dundas slates and quartzites, and is situated, according to Reid's plan, about 20 chains beyond the northern extremity of a narrow basic dyke which is continuous for a distance of two miles in a south-westerly direction.The mine eonsists of a prospecting adit following the course of a lode for about 275 ft. in a direction a little west of south. The low values of the lode are indicated by a bulk sample from a shallow winze about 100 ft. from the entrance which is reported by Reid to contain:

Jan 1, 1935

The Ross Goldfield is a unique gold resource. From its discovery in 1865 there was a growing understanding of the geology of the deposit as mining moved from the surface at Jones Flat in the south to underground extraction at Ross Flat further north. Multiple layers of gold-bearing gravels were penetrated in deep shafts and six rich gold-bearing bottoms were worked. The ultimate bottom on the Old Man Group gravel surface has never been reached either at Jones Flat or at Ross Flat. Mining at Ross Flat was ultimately halted by uncontrollable flooding, by escalating costs and by a shortage of labour during the First World War. Mining at Jones Flat recommenced in the late 1980s and attention has once again been drawn to the potential magnitude of the resource at Ross Flat. Research of historic literature shows that there is potential for a bulk gold grade of 400 mg/m3 in a volume of 82 million cubic metres of gravels which lie in a basin between Jones Flat and north Ross.

Jan 1, 1993

As requested by my fellow members I shall endeavour to read a paper on the Treatment of the Auriferous Sulphide Ores of Kalgoorlie from a metallurgical standpoint. Before going into the subject it will be necessary for me to make some slight explanations. As most of you are aware many of our London friends holding interests in some of these mines think it necessary that their doings should be shrouded in mystery. The result of this is that in some cases it is impossible to get any official figures from the mines for this paper. I must ask you not to lose sight of the fact that in treating the sulphide ores of the Kalgoorlie mines we had absolutely no data to start on, and that to-day. we are just beginning to get a fair grip of tbe subject; and though very high extractions were announced when the first plants were started on sulphide ore, it was well known that this was only to maintain the public confidence in the mines to allow time to make necessary adjustments; and, as showing the advance made in the treatment of the ore, I notice several of the mines have published the results of the final or re-treatment of the residues of their first sulphide treatment. I have also had the opportunity afforded me of thoroughly sampling the residues of several of the principal mines, and find the results as now published absolutely correct.

Jan 1, 1901

By Manuel Pérez-Tello, María M. Salazar-Campoy, Óscar Rodríguez-Hoyos

A common problem during the operation of the Kaldo furnace is the formation of accretions and blockage of the injection lance due to splashing. This typically occurs during the processing of anodic slimes for the production of doré. In this work, a 1:7 scale model of the Kaldo furnace currently in operation at Metalúrgica de Cobre, Mexico, was built in transparent acrylic plastic. Water and colored oil were used to represent the doré and slag, respectively. The model was used to determine the maximum penetration distance of the injection lance under a variety of experimental conditions at room temperature. Input variables included two types of oil, rotation speed, inclination angle, and the fraction of the vessel volume occupied by the liquids (φ). A mathematical correlation for the dimensionless maximum penetration distance of the injection lance d ∗ as a function of φ, the Froude number of the liquids in the vessel (Fr), the Reynolds number of the gas jet (Re), and the oil-to-water kinematic viscosity ratio (η)was developed. Reasonable agreement between the calculated and experimental values was obtained. Digital images showed that splashing was caused by the turbulent gas jet impinging upon the free surface of the liquids, whereas the cascade effect was negligible. The results of this work have been useful to improve the operation of an industrial Kaldo reactor.

By Robert B. Bittner

The Sutong Bridge across the lower Yangtze River in China will have, when completed, the longest span (1,088 m) and the highest towers (306 m) of any cable stayed span in the world. The foundations for this record setting span will also be record setting. They are located in water depths exceeding 30 m with maximum flows exceeding 3 m/sec. The soil at the site of the main pylons consists of layers of silty sands and silty clays extending to bed rock at 270 m below river elevation. This paper describes the innovative methods used by the team of foundation designers and constructors to support this record setting bridge at this very challenging site. This paper covers three specific topics related to the foundations of the Sutong Bridge: ? Design and construction of the 131 drilled shaft (2.8/2.5 m diameter and 114/117 m long) under each of the two main pylons, ? Design and construction of the scour protection for the two main pylons, ? Construction methods used to construct the waterline pile caps (113.8 m by 48.1 m by 13.3 m deep) under each pylon.

Jan 1, 2005

By S. E. Pérez-Fontes

An experimental study on the oxidation of chalcopyrite (CuFeS2), pyrite (FeS2), covellite (CuS) and chalcocite (Cu2S) particles was conducted by means of differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) techniques. The oxygen concentration in the process gas was set to 40% and 70% (by volume) and a heating rate of 40°C/min was used. Response variables included the temperature of incipient reaction, the total exothermic heat of reaction, particle mass, morphology and mineralogy of the reacted particles. Based on the experimental data and phase stability calculations, reaction mechanisms were proposed to represent the behavior of the particles during oxidation. The reaction mechanisms were verified by X-ray diffraction (XRD) analyses of the oxidized particles and by thermochemical and mass balance calculations to reproduce the DSC and TGA data. Overall kinetic models were developed to represent the evolution of the exothermic heat of reaction as a function of time.

Jan 1, 2007

By R J. Merchant

The Hauraki goldfield is located east of Auckland in the North Island of New Zealand. It includes Great Barrier Island, the Coromandel Peninsula and the Coromandel and Kaimai Ranges as far south as the town of Te Aroha and south east to Te Puke. It has a total north-south extent of about 180 km and an area of 3000 km2. The goldfield is the most productive in New Zealand, and while production at present is negligible, the area has undergone continuous exploration over the last seven years.

Jan 1, 1984

By Thomas M. Barczak

The intent of this paper is to make mine operators and engineers aware of parameters which affect the loading behavior of passive roof support systems. The strength of a passive roof support element alone is not a meaningful measure of support performance. Passive roof support elements and the surrounding strata act as a system, responding to changes in the physical mine environment due to the extraction of coal and associated redistribution of stresses. The load- ing of a passive roof support element is a function of the stiffness of the roof support structure; a stiffer structure will react a higher load to a converging mine roof than will a more flexible structure. If the stiffness if the support structure is not properly designed, excessive loading will result due to the displacement of the mine roof, causing premature failure of the support. Ideally, the yield strength of a passive support needs to be no greater than that required to support the dead weight of the immediate mine roof, providing the post yield characteristics of the support are compatible with the irresistible convergence of the overburden strata and the support system continues to provide this resistance after reaching its yield load. Idealized design considerations for passive roof support systems in terms load-displacement characteristics discussed. The stiffness and yield characteristics of wood concrete cribbing, as determined controlled tests in the Bureau's Roof Simulator, are compared preliminary recommendations passive roof support utilization also provided.

Jan 1, 1987

THE treatment by chlorination of the Mount Morgan Gold Mining Company's ores was first accomplished, early in 1886, by a works having a capacity of 25,000 tons per annum. Shortly afterwards another works was established, capable of dealing with 50,000 tons per annum. The extraction of gold was originally successful and satisfactory, but running expenses were high, averaging £2 19s. 6d. per ton of ore treated. These works were believed to be the largest chlorination pJants in the world at that time. As might have been expected, the mechanical details and chemical process had not been perfected, and, moreover, both works were hurriedly built, and operating expenses were not then considered of such prime importance, as the ore at that time was of very high grade the large quantities of low grade ore since dealt with not being then considered, since the bulk of it was not even known to be in existence.These two works consisted of lock-breakers, high speed rolls, screens, elevators, &c., for crushing; a large number of small handrabbled reverberatory furnaces for roasting; one-ton chlorination barrels and three-ton leaching vats for chlorination.

Jan 1, 1910

By A B. Christie

Space-based synthetic aperture radar (SAR) data is becoming available over much of the world, includingNew Zealand. Radar imagery has a number of very advantageous features, including all-weather capability; it also has artifacts, such as layover, which require processing before these data may be used to best effect.   This paper gives an outline of SAR, details the image processing required, and discusses the use of the first New Zealand Japan Earth Resources-1 SAR data to aid geological mapping on the Coromandel Peninsula.

Jan 1, 1994

By R L. Brathwaite

The mesothermal quartz-scheelite lodes of the Wakamarina valley are one of twelve known mined or prospected gold-bearing areas in the Marlborough Schist. Recorded production was 556 kg gold, a little silver, and c. 390 t scheelite. 134 m of the 1800 m long Golden Bar reef are accessible in the No 2 level of the Golden Bar mine. The reef is a typical multi-banded mesothermal vein, mostly c. 1.75 m wide, enclosing narrow horses of schist country rock. Scheelite is sparsely distributed, and is more common in small veinlets in the hanging wall schist. The country rocks are textural zone I-1m schists of prehnite-pumpellyite to pumpellyite-actinolite metamorphic facies. Their geochemistry suggests they are part of the Caples Terrane, and of calc-alkaline volcanogenic arc origin. The associated Wakamarina Quartzite is strongly recumbent folded, and of the same metamorphic grade, with abundant pumpellyite, stilpnomelane, and garnet, presumably spessartine. Although it has geochemical signatures of a deep sea sediment, it is depleted in Cr and Cu, and greatly enhanced in K and Ti, when compared with a standard chert. It also has trace element characteristics of a calc-alkaline arc-related sediment. However, associated greenschist has MORB-like incompatible element chemistry. The Golden Bar reef lies within a steeply dipping, normal to transtensional dip-slip fault adjacent to a shallow-dipping mylonite shear zone, which, at least on the footwall side, is 040 m wide. The shear foliation has been severely dragged down to nearly parallel the Golden Bar reef within 1 m of the quartz lode. Preliminary structural analysis suggests that the shear zone is extensional. X-ray diffraction analyses of the wall rocks show a progressive depletion of amphibole, stilpnomelane, and pumpellyite towards the reef, and enhanced illite/muscovite and Kfeldspar adjacent to the lode, along with possible graphitic carbon within 10m. Two zones of intense quartz veining occur, one adjacent to the hanging wall for 12 m and one from 40 m outwards. Quartz vein systems in the country rock are complex and span from pre-schistosity to post-mylonite. They include multiple generations of quartz, actinolite, stilpnomelane, pumpellyite, albite, adularia, chlorites, illite/muscovite, calcite, and scheelite. Metal analyses across the Golden Bar reef showed gold values of 0.13.1 ppm, and low tungsten values, consistent with the observed sporadic scheelite occurrences. As and Sb are at background levels, but enhanced Cr (150 - 430 ppm) relative to the schists (30 - 41 ppm) suggests that the source hydrothermal fluids passed through and leached mafic to ultramafic rocks.

Jan 1, 1994

By H. Naghavi, M. Karimi

"In self-aerated flotation machines, the gas rate depends on operational variables (e.g. froth depth and impeller speed), pulp properties (e.g. solid content and viscosity), and reagent addition (e.g. type and concentration of frother). The gas rate has a strong correlation with the flotation performance by influencing the gas dispersion properties and froth retention time. A factorial experimental design was used to study how the gas dispersion properties, the froth retention time, and the flotation performance respond to changes in froth depth and impeller speed (as the most common operational variables). An in-depth understanding of the effects of impeller speed and froth depth on the gas dispersion properties, especially the bubble surface area flux and froth retention time, is necessary to improve operating strategies for self-aerated flotation machines. All experiments were carried out in a 50 m3 selfaerated flotation cell in an iron ore processing plant. The results showed that the froth depth affected the metallurgical performance mostly via changing the froth retention time. The impeller speed had two important impacts on the metallurgical performance via varying both the froth retention time and the bubble surface area flux in the froth and pulp zones, respectively. The interaction effects of the froth depth and impeller speed were also established. This allowed us to develop a strategy for operating selfaerated flotation machines based on varying the froth depth and impeller speed with regard to the cell duty. IntroductionA mechanical flotation machine may be divided into two distinct zones. namely the pulp zone and the froth zone (Goodall and O’Connor, 1989; Yianatos, Bergh, and Cortes, 1998; Rahman, Ata, and Jameson, 2015a, 2015b). The overall flotation recovery, Ro, including the true flotation (particles attached to the bubble lamellae) and entrainment (particles recovered in water held in the bubble plateau boundaries), is a function of the recoveries in the two zones. It is calculated as follows (Dobby, 1984):"

Jul 1, 2019

By B. Lueger, D. Shen, M. Sedighy, R. Rand, R. Saleh, J. Cheung, M. Rifai, I. Khan, W. Sauri, D. Setianto

The world’s first active power demand stabilization system for a 3-electrode electric arc smelting furnace was commissioned at PT Vale Indonesia in December 2012 on Furnace No. 2 using an SPLC (Smart Predictive Line Controller). The SPLC technology in combination with the Furnace No. 2 rebuild and other upgrades has enabled PT Vale to increase the electrical input to the furnace by up to 20% on a stable and sustainable basis by eliminating peak powers that overload and trip out the electrical equipment, and by reducing power unbalances. The SPLC technology maintains smooth arc power using a continuously variable thyristor controlled series reactor. The SPLC compensates variations in the furnace arc with predictive changes in the circuit reactance at a speed of up to 60 times a second. The system started up quickly and has been shown to be easy to operate and maintain by PT Vale. PT Vale’s Operations Team has been testing the new system at set points of up to 90 MW on the newly re-built Furnace No. 2. Over the last 12 months, the throughput of Line 2 has increased by approximately 10% on an annual average; however, debottlenecking in other design areas of the operation is required in order to achieve 90MW operation on a sustainable basis. This outstanding success results from a combination of the furnace and other upgrades, the SPLC active power stabilization, and the skill of PT Vale in quickly adopting new technologies and maximizing the combined benefits of each technology in their operation.

Jan 1, 2014

By Ingrid Hann

The Triple Bottom Line ? Economic Sustainability ? Creation of Joint Venture companies ? Planned evaluation of other kimberlites ? Social Sustainability ? Impact Benefit Agreement and Participation Agreements ? Education and training initiatives ? Environmental Sustainability ? Environmental management ? Mine closure planning

May 1, 2008

By F. A. Guo

Ultrafine-grained surface layers were obtained by surface mechanical attrition treatment (SMAT) in copper and titanium samples. The thermal properties of the deformed layers were characterized using a scanning thermal microscopy (SThM) that allows thermal conductivity to be mapped down to the submicrometer scale. A theoretical approach, based on this investigation, was used to calculate the heat flow from the probe tip to the sample and then estimate the thermal conductivities at different scanning positions. Experimental results and theoretical calculation demonstrate that SThM can be used as a powerful tool for the thermal property and microstructural analysis of ultrafine-grained microstructures.

Jan 1, 2006

By A. Pratt

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

May 1, 2010

By P. H. S. W. Kulatilake

To exploit an underground mine effectively and safely, it is important to have a good understanding of the geotechnical behavior around underground excavations made in the mine. The aim of this study was to investigate the geotechnical behavior around a tunnel excavated in a metal mine in China at the three-dimensional level. Using the information available on lithology, geological structures, in-situ stress measurements, physical and mechanical properties of intact rock, discontinuities and interfaces between different rocks, a three-dimensional numerical model was built by using the 3DEC software to simulate a tunnel excavation under a high in-situ stress condition. Effect of the discontinuity network, possible intact rock and discontinuity parameter variability, representation of rock masses as discontinuum or continuum material and rock support system on the deformation, stress, failure zone and stability around the tunnel was investigated. A very good agreement was obtained between the collected field deformation monitoring results and the results of the conducted numerical stress analyses.

Jan 1, 2012