Search Documents

By K. Goshtasbi

In this paper a genetic algorithm is used in a heavily jointed rock mass in order to investigate the critical circular slip surface and modification of slope surface. This method was applied to the southern wall of the 6th Golbini Jajarm bauxite mine. The mine is the largest bauxite deposit in Iran, located to the northeast of the town of Jajarm in the Khorasan province. Estimated reserve of bauxite in this deposit is about 160 million tonnes. Field and laboratory investigations were conducted in order to determine rock mass behaviour. A genetic algorithm code that uses the Simplified Bishop method as an objective function was developed for findingt he safety factor of circular slip surfaces. Sensitivity analysis was applied to determine the optimum values of the genetic algorithm variables, such as population size, selection method, crossover and mutation rates. After finding the critical circular slip surface, slope modification is carried out by removing unstable sections from marked critical slip surfaces, and this process is repeated until the last unsafe section is removed. Based on this code, modification occurred during 7 steps, by reaching a safety factor of 1.3 in the last step. Finally, the modified slope angle of the southern wall of the 6th Golbini Jajarm bauxite mine was determined to be 48.44 degrees. Keywords: Genetic algorithm, slope modification, circular slips surface, 6th Golbini Jajarm bauxite mine .

Jan 1, 2008

By M. J. Little

Potgietersrust Platinums Ltd (PPRust) is Anglo Platinum?s only open pit operation. The major slope stability concern at PPRust is rapid, small-scale brittle failure on the west wall of Sandsloot open pit. In order to improve safety and mine more economically, a comprehensive slope monitoring strategy has been implemented. In the last 3 years four new state-of-the-art monitoring systems have been installed namely an ISSI microseismic monitoring system, a GeoMoS automated prism monitoring system, prismless Riegl laser scanners and a GroundProbe slope stability radar (SSR). Groundwater monitoring and visual monitoring have also been improved over the same time period. To complement the visual inspections, SiroVision digital photogrammetry is now used for predicting where future failures may occur. All these monitoring tools provide primary monitoring which is used to identify high risk areas. The SSR is then set up in that area to provide early warning of failure so evacuation can be successfully done. Fault tree analysis has proved that with this comprehensive slope monitoring strategy the geotechnical risk at PPRust is greatly reduced, allowing mining to continue safely and economically in challenging conditions.

Jan 1, 2006

By Manuel Rapiman, Ricardo Sepulveda

The feasibility study of Escondida Norte (ENorte), recommended a slope angle design for the Final Pit. But, according to the experience obtained with the slope adjacent to the West wall of ENorte, in which Compañia Minera Zaldívar (CMZ) gained in its phase 4, a slope of similar geotechnical characteristics will be exposed in the West Wall of Phase 1 (Premine) and of the Final Pit, with an interramp angle 53º and with very good stability results. In this regard, Minera Escondida Ltd. (MEL) performed a study of the slope angles for the phases mentioned and according to this delivered the results of this evaluation, the recommendations and/or the necessary conclusions in the design to ensure that the slopes are stable enough and may enable safe operational management of them.

Jan 1, 2006

By David Preece

The Thirlmere aqueduct was constructed over 110 years ago to provide water from the Lake District (in the north-west of England) to the city of Manchester some 60 miles (100 km) away. The aqueduct remains, to this day, a key piece of infrastructure in the distribution of raw water in the north-west of England. A short section of the aqueduct was identified as being in poor condition during routine inspections by the owner. Subsequent investigations attributed the conduit damage to the movement of unstable ground over the conduit. Bachy Soletanche Ltd was subsequently appointed to carry out the design and construction of the slope stabilisation works and to undertake repairs inside the damaged conduit. The works were undertaken on an existing slope which, in places stands at a gradient of up to 40º to the horizontal. Strict limitations on plant and equipment were imposed by the client (United Utilities) to ensure that slope and conduit loading and associated vibrations were kept to an absolute minimum during construction. An intensive instrumentation system was installed to monitor surface movements, ground movements at depth, conduit movement and strains across existing planes of weaknesses within the conduit. The solution comprised the installation of spaced piles up-slope and down-slope of the conduit. Restrictions were imposed on the minimum stand-off distance between the outside face of the conduit and the piling works so targeted permeation grouting was undertaken to improve the ?connection? between the conduit and the down-slope piles. The presence of existing sub conduit groundwater flows was suspected and the permeation grouting was focused in areas to minimize disruption to the groundwater regime. The paper presents the basis of the design and highlights the combined construction and instrumentation methods adopted to minimise damage to this valuable asset.

Jan 1, 2011

In a field test at Mount Isa Mines Ltd., a system developed by ICI Australia Ltd. for bulk loading "MOLANITE", an ammonium nitrate slurry blasting agent into ring drilled holes of wblcvel open stopes, was shown to be satisfactory. The fragmentation produced by the slurry was a significant improvement over ANFO and the stope production rate was increased by approximately 50%. Indications are that the charging rate and labour costs will not be greatly changed if a slurry system is used.

Jan 1, 1973

By D E. Gadd

Since October 1972, New Zealand Steel Mining Ltd has loaded around ten million tonnes of ironsand concentrate from single-point mooring buoys located off-shore at Taharoa on the west coast of the North Island of New Zealand. Before the first off-shore loading system was installed a considerable research effort was applied to proving the slurry loading technique. Subsequently the system has been expanded and a new buoy, pipelines and pumping system were installed in early 1978. Since then 110 000 DWT class ore carriers have been loaded at rates of around 2600 tonnes per hour through twin submarine pipelines. This paper reviews the operation of the ship loading system and attempts to answer the question: 'If the Taharoa operation were to be planned in 1980, would the same research spending be necessary or have published research results since, made such practical tests unnecessary?'

Jan 1, 1980

By Baha Abulnaga

Slurry pipelines are used in a number of countries to convey processed ore mixed with water over long distances from remote mine sites to ports or plants for further processing. In Egypt and Sudan, numerous mineral resources are scattered in remote areas. Through the years, Egyptian geologists have identified 268 sites for metallic ores and 386 sites for industrial nonmetallic minerals. A large portion of these sites are in the Eastern Desert in an area called the Nubian Shield. Similar sites are found in the Sudan where mining contributes to less than 1 percent of the gross domestic product (GDP). There are three important components of infrastructure needed to develop these resources ? power, water and transportation. While Egypt is able to satisfy 70 percent of its needs in iron ore from the Gadideh Mine in the Western Desert, it needs to expand its other resources to reduce imports heavily sedimented. Dredging of these sediments and transporting them by slurry pipelines would enhance an industry of bricks or agricultural development based on tailings technology often used in mining. This article explores the potential for slurry technology for opening new mines in the desert or recuperating the sediments of the Nile. The technology by itself would be new to both countries and would benefit from collaboration, particularly to de-silt the Nasser-Nubia Lake.

Jan 3, 2010

By G. R. Addie

"In February, 1975, the President of Georgia Iron Works Company, Mr. Tom Hagler decided to build a new hydraulic laboratory to water performance test all of the companies' centrifugal slurry pumps.Equipment procurement started in March, 1975, by ordering of a mini computer data acquisition system.Work commenced on the lab in July, 1976, by erection of a Butler Building and the laying down of a 20,000 gallon concrete sump.By late October, a facility compromising two water test loops of 8"" and 18"" pipe diameter was in operation carrying out head quantity and suction performance tests on pumps up to 16"" in size.In August of the following year, an 8"" diameter pipe slurry loop was installed to enable pipe friction and deposition velocity of a slurry to be measured in an 8"" inside diameter pipe.With the encouragement of Reserve Mining in Minnesota and IMCC in Florida, this was followed in March, 1978, by the addition of over 300 feet of 18"" diameter pipe to make up an 18"" diameter pipe slurry system complete with head loss and deposition velocity observation sections.The office and shop areas of the lab were again expanded in April, 1978, to provide further expansion to the test sections and staff facilities."

Jan 1, 1980

By George Wilson

When pumping abrasive slurry mixtures, special attention must be given to pump design and construction. The second article in this two-part series describes some design features to consider when selecting centrifugal slurry pumps. Hydraulic Design Most centrifugal pumps are conventionally designed to achieve the desired hydraulic performance at the highest efficiency and lowest cost when handling clear fluids in reasonably clean environments. Manufacturing limitations are not imposed on the configuration of the pump, since conventional materials such as cast iron, bronze, and stainless steel are used. Manufacturers and buyers usually select the highest specific speed commensurate with the lowest cost attainable. Part life is almost infinite. When a centrifugal pump is designed for slurry service, the important factors in pump design are wear and materials of construction; size and efficiency assume lesser importance. The pump must operate at low rotational speed and the impeller has to be a truly radial flow design. These factors immediately determine that the pump must be of a low specific speed design in the range of 600 to 1800. The specific speed is a type number that is constant for all geometrically similar pumps; it designates the geometry of the impeller and casing. [ ] where n = rpm, Q = flow (US gpm), H = total head (ft), and Ns = specific speed. Since wear is a function of velocity it can be shown that for a given head and capacity, wear will increase with increased Ns. Centrifugal Pump Casing The casing has a profound effect on performance. If designed incorrectly it can destroy a large part of the energy given to the flow by the impeller, resulting in low efficiency, high hydraulic forces, and excessive wear on both the casing and impeller. In a conventional spiral volute, the static pressure around the impeller is uniform only when there is a free vortex velocity distribution in the volute, i.e., when the spiral flow from the impeller coincides with that of the volute spiral. This occurs only at the best efficiency point (BEP), between the pump's best operating zone and over capacity zone. Departure from the free vortex velocity distribution in the volute at partial or over capacities produces circumferential pressure gradients at the impeller periphery, which is directly proportional to the specific gravity of the mixture being pumped. At partial or over capacities, the flow will not tolerate the abrupt deflection at the tongue and severe energy losses and wear are created near the casing throat and on the impeller. Concentric and semi-concentric volute designs produce uniform static pressures at the impeller periphery and make the pump, much less sensitive to "off"' BEP operation. Hydraulic forces and wear are considerably reduced-eliminating the tongue prevents abrupt deflection of the flow, turbulence is minimized, and the velocity in the casing volute and throat is reduced. Good efficiency is sustained over a wider operating hand. Casings of this design are easy to cast. • Spiral volute (conventional)-Radius to the outer periphery of the casing and the volute area constantly increases. • Semi-concentric casing-Radius to the outer periphery of the casing and volute area remain constant within a certain angle. • Concentric casing-Radius to the outer periphery of the casing and volute area remain constant through 360°. The degree of concentricity must be reconciled with efficiency, hydraulic radial load, and wear for each specific speed chosen. Up to 1200 Ns the casings can be fully concentric without sacrificing too much efficiency. Above 1200 Ns, the casings can be semi-concentric. The angle of concentricity

Jan 10, 1981

By C. A. Horne

"The transportation of mineral solids in the form of slurry is a subject most of us are associated with and, in fact, live with on a daily basis. The design parameters of slurry systems and most important the prime movers or cent¬rifugal pumps, are frequent and often controversial subjects due to the lack of practical guidelines which, if known and followed, can increase both reli¬ability and service life of the equipment.In this talk, emphasis has been placed on the practical side or rule-of-thumb approach to applications which, in turn, has been related to successful field results. The theoretical content and complex design criteria associated with actual equipment design has consequently been held to a minimum in the following discussions.I. BASIC SLURRY PUMP DESIGN CONSIDERATIONSFirst, to better understand how a centrifugal pump performs work, a basic description of the operating principles are in order.A. Operation In a pump, mechanical energy is transformed into pressure energyby virtue of the centrifugal force exerted by the rotating impeller. The liquid is discharged by centrifugal force at a velocity required to generate a given head and the volute collects the liquid so useful work can be done by the conversion of kinetic energy to pressure energy."

Jan 1, 1976

By James J. Kabat, James A. McDonald

Impregilo/SA Healy JV recently completed this Project using the first slurry shield TBM’s in the United States. The Project used two TBM’s to mine 18,000 feet in sands, gravels, and silty alluvial materials under the Willamette River and downtown Portland, Oregon. This paper discusses alignment and geological conditions, equipment selection and plant setup, and tunnel excavation means and methods, parameters, and results. Extensive hyperbaric operations were required and will also be discussed.

Jan 1, 2007

By S Lush, R Polglase

McConnell Dowell is pleased to be given the opportunity to present two papers to this conference. The first is a general discussion paper on our work in the field of slurry transportation. The second will be a technical paper on the development of a welded coupling compatible with urethane lined pipework. We trust that by discussing our recent work we can leave two lasting impressions on you: the versatility and useful role of slurry transportation, and the leading role taken by New Zealand in this technology This paper discusses three recent projects the New Zealand Steel Ironsand Transfer Line the Coarse Coal Ship Loading Technology the Nerang River Sand By-pass System. These have followed on from the other slurry projects with which McConnell Dowell has been associated such as the ironsand export trade at Waipipi and Taharoa. The New Zealand Contractors Federation awarded the Construction Award for 1986 to McConnell Dowell for the Ironsand Slurry Pipeline.

Jan 1, 1986

By Gino Vogt

In mechanized tunnelling operations, performance, consumption and safety are main factors for jobsites. One of the most important components effecting these factors, especially in slurry TBM operations, are Slurry Treatment Plants (STPs). Inadequately dimensioned and designed STPs create bottlenecks for tunnelling operation and jeopardize time schedules and performance. Inefficiently planned STPs could drastically increase consumption figures such as electrical power, bentonite, water polymers, etc. Inaccurately selected and treated suspension properties can cause a high-risk potential for the whole project. This paper debates the relevant key parameters for STPs from start to finish of a project and its results in influencing factors from the manufacturer’s point of view.

Dec 1, 2022

By Gino Vogt

In mechanized tunnelling operations performance, consumption and safety are main factors for jobsites. One of the most important components effecting these factors, especially in slurry TBM operations, are Slurry Treatment Plants (STPs). Inadequate/ suboptimally dimensioned and designed STPs create bottlenecks for tunnelling operation and jeopardize time schedules and performance. Inefficiently planned STPs could drastically increase consumption figures such as electrical power, bentonite, water and polymers, etc. Inaccurately selected and treated suspension properties can cause a high-risk potential for the whole job. This paper debates the relevant key parameters for STPs from start to finish of a project and its results in influencing factors from the manufacturer´s point of view.

Jun 13, 2021

By Stephen T. Young

The construction of Phase 2 of Hong Kong Station, its retail podium and International Finance Centre Two, the tallest building in Hong Kong, will be completed in the middle of 2003. This paper describes the design and construction of the slurry wall for the Station (both Phase 1 and Phase 2) and the two commercial buildings at the Station. The slurry wall is used as the permanent earth support wall for the station box and the excavation depth ranges from 70 feet to 120 feet. Top-down construction technique was adopted to support the excavation of the station, while circular cofferdams relying on hoop stiffness were constructed to support the basement excavation of the two towers. The designed behavior of the slurry wall is also compared to the as built behavior.

Jan 1, 2003

By Carnevale Francesco, Bracci Laudiero Alberto, Pampanin Piero

"SummaryIn the Port of Naples a slurry wall has been realized through a sandy layer up to a deep tuff layer using the Cutting Soil Mixing technique.The executed panels have dimensions of 2.8 m x0.65 m in plan and a total length of 25 m. Primary and secondary panels have been executed using the wet to wet technique. During the panels execution the following parameters had been measured: injection pressure, injected volume, verticality. At the end of the works an exploratory campaign has been carried out through boreholes collecting samples for laboratory tests in order to verify the diaphragm thickness and its physical and mechanical properties (i.e. unit weight, unconfined compressive strength).The interpretation of the collected data allowed to verify the efficiency of the method, the volume of slurry loss due to permeation during the panels execution, the quantity of the obtained spoil compared to the volume balance equation, both for the sand and the tuff layer.Eventually, the measured physical and mechanical characteristics of the panels have been correlated to the execution method performed.IntroductionIn the Naples Port area there is a polluted site which has to be hydraulically isolated in order to prevent the pollution of the groundwater that flows from land to the sea through the Port area. A hydraulic cut-off wall has to be realized and particularly a slurry-wall realized using the CSM method had been executed.To date, two stretches have been executed, 140 an 110 m in length respectively, as shown in Figure 1 and Figure 2.After execution, the slurry-walls have been investigated with boreholes. In-situ and laboratory tests on the recovered samples of grout have been carried out; furthermore, the geotechnical parameters of the mix composing the wall have been measured."

Jan 1, 2014

By Louis Ware

BEFORE the war we often heard the term "Big Business." And there were complaints of the ills and abuses attributed to bigness in business. Although there were examples where the small businessmen spoke for their rights and sought protection from the bigger ones, it has only been in recent war years that a tendency has developed definitely to divide the business of our nation into the big and the small. In some cases, those with an eye to the political value of the vastly greater number of small businessmen of the country have fomented this division by hurrying to the protection of these more numerous voters, and intentionally or not have emphasized in their writings and verbal attacks any and all differences of these interests that could either be found or fabricated to, suit the occasion. It has become another example of breaking the people into classes and thus setting up the basis for the claims of one class against another, and the subsequent demand for legislation and Governmental aid. The terms "big" and "small" are purely relative. One businessman, employing a hundred men, told me recently he did not know which adjective would be more appropriately applied to his operation. He did not know whether he should join the small operators' group that had been organized, or should consider himself big. He said that his present plant seemed big to him when he looked back to its humble beginning many years ago with a couple of men in two rooms. Yet, when compared with many of his competitors who employ thousands, his was small. He did add, however, that he probably became big one day a few years ago when the union moved in and organized his employees.

Jan 1, 1945

By S J. Brace

About 180 000 tons of explosives are used annually underground in South Africa. Most is loaded into holes less than 50mm in diameter. 75% is consumed in the gold and platinum mines where holes are between 25 and 4omm in diameter and no more than 3.0m in length. The small amount of explosives per hole with extreme conditions of heat, humidity and seismic activity, make the choice of explosive on safety and technical grounds very important to the success of a blasting operation. Taken together with the fact that many underground precious metal operations are now marginal then the choice of an explosive, when its price is also considered, becomes critical to the very viability of some mines.

Jan 1, 1994

By P. J. Yttrup

Small diameter timber piles are used in Australia to solve foundation problems in soft or filled ground and expansive soil. The paper describes the results of pile load tests to develop simple methods for bearing capacity determination and observation of the performance of piles in expansive soil.

Jan 1, 1989

By Brain E. Gombos

The Allen Park Sanitary Sewer Overflow (SSO) Tunnel and relief sewer project, located in the city of Allen Park, MI, is a long-term corrective action designed to bring Sanitary District One?s sanitary system into compliance with its 2005 consent order and service contract with the Detroit Water and Sewerage Department (DWSD). The $20 million project is intended to reduce Allen Park?s wet weather discharges to DWSD, reduce bypass pumping to the Ecorse Creek and limit the future risk of basement flooding by providing storage during wet weather events and eliminating hydraulic bottlenecks in the sanitary sewer system.

Jan 1, 2013