Search Documents

By X Hu, C-C Yang, J Pan

In this work, preheating and roasting tests of pellets made from blends of Western Australia ultra-fine (WAU) magnetite concentrate and Chinese domestic magnetite concentrate or Brazilian hematite concentrate were carried out. The results showed that pellets made from 100 per cent WAU magnetite concentrate possesses inferior preheating and roasting performance when preheating at 1050°C for 20 minutes and roasting at 1300°C for 40 minutes, the compressive strength of preheated and fired pellets is 502 N/pellet and 2313 N/pellet, respectively. When 40 per cent Chinese domestic magnetite concentrate or 20 per cent Brazilian hematite concentrate was blended with 60 per cent or 80 per cent WAU magnetite concentrate, the appropriate preheating temperature of the pellets are reduced from 1050°C to 950°C and 975°C, and also the firing temperature of two types pellets are decreased from 1300°C to 1250°C and 1280°C respectively. Moreover, the compressive strength of fired pellets is obviously improved up to 2746 N/pellet and 2630 N/pellet respectively. Microstructure analysis of the fired pellets made from 100 per cent WAU shows its poor growth of Fe2O3 grains, low interlinkage degree of hematite grains, small size of crystallised grains and high porosity of pellet; however, the fired pellets that blended with domestic magnetite concentrate or with Brazilian hematite concentrate have fully growth of Fe2O3 grains, closer interlinkage of hematite grains, lower porosity and stronger consolidation. The preheating and roasting performance of WAU magnetite concentrate pellets can be improved by optimising ore matching.CITATION:Pan, J, Hu, X, Zhu, D-Q and Yang, C-C, 2017. Pelletising performance of Western Australian ultra-fine magnetite concentrate and strengthening technique by optimising ore matching, in Proceedings Iron Ore 2017, pp 97–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By H. N. Egan

Faced with a severe disposal problem of their fines from a coal mine in the heart of the Appalachian Mountains of extreme eastern Kentucky, Eastern Coal Corporation has built a special plant to pelletize the fines into high quality coal pellets meeting the requirements of the metallurgical market. These low-ash, low-sulfur pellets measuring 3/4 x 3/8 in. contain less than 1.5% moisture and have the same stability as raw coal of the same size. Although Eastern Coal is mining 6000 tpd, the company had, until recently, no provision to recover the fine coal which was included with the plant effluent pumped to a 12-acre refuse pond. The pond, impounded behind the coarse refuse dump, rose 15 ft last year and obviously no pond can stand many years at this rate. Limited pond space in this rugged area of steep hills and narrow valleys dictated a revised disposal method.

Jan 11, 1967

By P. Mbele

Iron ore concentrate is not easily transported to, or processed in, ironmaking plants, therefore it is necessary to agglomerate. This paper will determine the possibility of agglomerating Sishen concentrate into suitable ironmaking feedstock. Pelletizing is one of the conventional and preferred agglomeration processes for iron ore concentrate investigated at Kumba Value-In-Use Laboratories. Sishen concentrate was mixed with binder, and then pelletized using a laboratory pelletizing disc; afterwards the green pellets were indurated at high temperatures to give strength high enough to survive handling and lessen disintegration in the shaft during ironmaking. Sishen pellets have satisfactory physical and metallurgical properties which make them suitable feedstock for the direct reduction processes. These were tested under Midrex shaft operational conditions and performed well, with a metallization of 94.47% being attained.

Jan 1, 2012

By Roy A. Koski

This paper describes variations in feed characteristics, preparation techniques, response to induration and product quality in pelletizing magnetite concentrates, earthy hematite ore fines, and specular hematite concentrates in grate kiln systems. The Cleveland-Cliffs Iron Company manages plants processing these various materials on the Marquette Iron Range in northern Michigan. The operations include the Humboldt Mining Company, Marquette Iron Mining Company, Empire Iron Mining Company and the Pioneer Pellet Plant. The combined output of the operations is approximately 9,000,000 long tons per year. The Humboldt Mining Company, owned by Ford Motor Company and Cliffs, produces pellets from a specular hematite concentrate. The Empire operation, which processes magnetite ore, is owned by Inland Steel Company, McLouth Steel Corporation, International Harvester and Cliffs. The Pioneer operation, which processes earthy hematite ores, is a joint venture of Republic Steel Corporation, McLouth Steel Corporation, Bethlehem Steel Corporation and Cliffs. The Marquette Iron Mining Company, owned by hones and Laughlin Steel Corporation, International Harvester, Wheeling-Pittsburgh Steel Corporation and Cliffs, produces pellets from specular hematite concentrate at the Republic Mine and Eagle Mills Pellet Plant. With the exception of the Eagle Mills plant, the operations employ the grate-kiln pelletizing system. Descriptions of the Empire, Pioneer and Republic operations, which have a combined capacity of 7,200,000 tons per year, are given in the paper.

Jan 1, 1969

From time to time efforts have been made to classify rocks according to their hardness, toughness and abrasiveness, and to use these classifications to provide an indication of the ease or difficulty with which they may be drilled. However, rocks classified as of similar type on this basis may vary considerably in their .resistance to the penetration of a rock drill bit due to differences in their physical state.For instance, fine grained rocks of granular texture are more difficult to drill than equivalent' rocks of coarser structure, altered rocks drill more readily than unaltered ones, and silicified rocks usually exceedingly hard and tough may be so shattered by movement as to be drilled at a rate comparable to quite soft rocks. Therefore, considerable latitude has existed in this method of defining their drillability, and no values generally acceptable have materiaJised; so that, when the drilling properties of rocks are discussed, it is common practice to refer to their hardness or toughness in a greater or lesser degree depending to some extent on the emotional state of the drill runner.REFERENCES AND STANDARDSThe 'introduction of tungsten-carbide tipped rock-drill bits for use with percussion rock-drills has thrown increasing emphasis on the need for defining a rock's resistance to penetration in a more concise and generally acceptable...

Jan 1, 1950

Interest in the potential use of high-density, thickened tailings has recently increased significantly. Reasons for considering this new technology vary across projects, but commonly include the need to conserve water, perceived lower risk of catastrophic failure, potential easier closure, or even reduced overall costs. As with any new technology, there has been some tendency to overstate its potential benefits. This paper reflects on whether or not the potential benefits that have been attributed to paste and thickened tailings have been realized. Using a grading system, thirteen benefits that were ascribed to the new technology some years ago are evaluated. Data is taken from case studies, and it is suggested that the key proven benefits appear to be reduced operating costs in some cases, reduced wall-building costs, and reductions in water consumption. One key potential benefit that has not been universally achieved is a reduction in the footprint of the tailings facility. Reports in the literature highlight the sometimes confusing nature of trade-off studies. Unless full life-of-mine costs are considered, these studies can be misleading and incorrect. The need to establish a consistent basis for comparative studies is discussed.

Jan 1, 2012

By WM. HUFF WAGNER

Computations and allowances for mine depletion for Federal income tax purposes depend upon the meaning of certain terms in the pertinent provisions of section 114(b) 4 of the Internal Revenue Code. Unfortunately, but one of these terms is defined in the Code. Congress left it to the Commissioner to define the other terms in the Regulations. Even though the Commissioner, through his staff, labored long and earnestly to draft these definitions they have not been satisfactory to the mining industry, because the definitions in the Regulations and the interpretation placed thereon by the Commissioner do not state what the industry believes to be the clear and obvious intent of Congress. Consequently serious and prolonged disputes, unduly delaying the settlement of Federal tax returns involving percentage depletion deductions are continually arising between taxpayers and the Commissioner.

Jan 1, 1949

By J. J. Stacey

Large mining companies generally follow the distributed ownership corporate model, with a board of directors responsible for decisions that affect both shareholder value and stakeholders of the company. The board is simultaneously responsible for setting the culture and values of the corporation, which drive performance and priorities. Companies listed on the Johannesburg Securities Exchange (JSE) commit to sustainable development in various ways, either by virtue of implementing the King Code of Governance 2009 (King III) and/or through their own public reporting on social and environmental matters. Many mining companies make public statements regarding their support for environmental stewardship, ethical behaviour, and fair treatment of communities. It is a local, regional, and indeed, global phenomenon that companies fail to deliver on these statements. Research was carried out through the Institute of Directors of Southern Africa in 2007, and followed up in 2012, regarding directors? understanding of sustainable development issues, the relative priorities, what is needed for ?radical change? to effect sustainable development, and what enables or constrains the latter. Pertinent findings of both surveys are presented in this paper, and it is suggested that ?on-the-ground? performance may be indicative of the nature of leadership and decisions in the topmost ranks of the company. The results indicated that environmental concerns fall consistently below social issues. Financial capital ranked most important, and while environmental issues are recognized as being of strategic concern for the long-term, they ranked as being the lowest importance of all ?Five Capitals? (Financial, Manufactured, Social, Human, and Natural). Social capital ranked second lowest, with black economic empowerment being the only high-priority social issue. There is also evidence that certain companies within the mining sector fail to recognize their absolute dependence on natural resources. Much is made in academic and popular literature of the need for a new type of leadership for the radical shift to sustainable development: at company level this implies therefore a new type of director. The research found that only 14 per cent of directors felt that board decisions are consistent with their personal values; while intentions are strong to behave ethically and serve sustainable development, actions to give effect to these intentions lag significantly. Respondents indicated that the top impediments to courageous leadership for sustainable development related to personal issues of maintaining the image of being a director, fear of appearing weak, fear of being a lone voice, and bowing to board-colleague peer pressure.

Jan 1, 2014

By S. Kahraman

The correlations between the modulus ratio and penetration rate of rotary and percussive drills were statistically investigated using the raw data obtained from the experimental works of different researchers. An inverse power law was found between the modulus ratio and the penetration rate of rotary and diamond drills. The penetration rate of rotary drills and diamond drills decrease with an increasing modulus ratio. The penetration rates of percussive drills increase with an increasing modulus ratio. There are significant linear correlations between the penetration rates of percussive drills and the modulus ratio. In one of the cases of percussive drilling, a strong correlation between the penetration rate and the modulus ratio was found for the rocks having a porosity value lower 1.23 %. It can be concluded that the modulus ratio might be a representative measure of rock drilling efficiency. However, further study is necessary to check the validity of the derived equations for other rock types. The effect of porosity on the correlations between the modulus ratio and penetration rate needs to be further investigated.

Jan 1, 2003

By D J. Brake

In most underground mines, the ventilation system is a significant portion of the total mine capital and operating cost and the largest consumer of underground electrical power. The effectiveness of the ventilation system has a major bearing on the safety, health, comfort and morale of underground personnel, and has a critical role in meeting production targets and therefore business revenue. Perhaps the most important component of the primary ventilation system is the primary fan. Correct performance testing of the primary fan during the warranty period is important not only to ensure the mine has obtained the asset that it paid for and can therefore deliver on the fanÆs crucial safety and economic role in the future of the mine, and to provide a justification for releasing final performance warranty payments to the supplier, but also to provide a benchmark or baseline against which to assess future performance issues. As there are at least three potential international standards available to measure fan performance, there has been considerable confusion regarding which of these to use for testing primary mine fans, and also the correct allowances and tolerances to use. This paper provides guidance on which standards to use for different applications, how the standards should be interpreted, what allowances and tolerances are reasonable, and other important issues to be resolved with the fan supplier prior to making a contract award. The paper also discusses practical issues and methodology for in situ primary fan performance testing.CITATION:Brake, D J, 2013. Performance and acceptance testing of main mine ventilation fans, in Proceedings The Australian Mine Ventilation Conference , pp 141-148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Michel R. Julien, Michel Lemieux, Jean Cayouette, Daniel Talbot

"The Louvicourt Mine located near Val d’Or, Quebec has been in operation since 1994. It produces copper and zinc concentrates. The tailings generated from the ore processing operations have a strong net acid generating potential. Louvicourt Mine, a grass root project, was designed for closure with the best available technology at the time of design. In order to inhibit short and long time acid potential generation, sub-aqueous disposal was selected at the design stage. Given the fact that disposal in a natural lake was ruled out up front for obvious reasons related to loss of natural habitat and risks of permitting delays, a man made facility built with dams was planned. This mine includes therefore the first fully man-made sub-aqueous tailings disposal facility built in Canada. The requirement of using sub-aqueous disposal had serious implications on the placement of tailings. This tailings facility located about 9 km from the mine site has been selected based on the available natural confinement, the favorable foundation and hydrogeological conditions. This paper describes the site and the design criteria that were used. A presentation is also made on the placement technique to maximize storage and its impact on the operation of the basin. The performance of the basin, the dams and the decant structures is reviewed.Résumé : La mine Louvicourt, située près de Val d’Or, Québec est opérationnelle depuis 1994. Elle produit des concentrés de cuivre et de zinc. Les résidus générés par les opérations de traitement du minerai possèdent un fort potentiel net de génération d’acide. Le parc à résidus de la mine Louvicourt, implanté dans un milieu naturel intact, fut doté dès sa conception initiale de la meilleure technologie de fermeture disponible à l’époque, soit la déposition sous couverture aqueuse et ce, dans le but de bloquer le potentiel de génération d’acide à court et à long terme des résidus. Etant donné que la déposition dans un lac naturel fut mise de côté dès le départ pour des raisons évidentes reliées à la perte d’habitats naturels et au risque d’introduire des délais dans l’émission des permis, un étang artificiel délimité par des digues a été conçu. Cette mine fut donc la première au Canada à être dotée d’une installation anthropique de disposition des résidus sous une pleine couverture aqueuse. L’exigence d’une déposition sous couverture aqueuse a eu des implications sur le mode de mise en place des résidus. L’emplacement de l’installation de gestion des résidus a été choisi en un lieu situé à environ 9 km du concentrateur sur la base du confinement naturel disponible et des conditions hydrogéologiques et géotechniques favorables. Cet article décrit le site et les critères de conception utilisés. Une présentation est faite sur la technique de mise en place utilisée pour maximiser l’entreposage et son impact sur l’opération du bassin. La performance du bassin, des digues et des structures de décantation est également revue."

Jan 1, 2004

By Sam Yao, Ali Naeem, Sara Barrett

Brooklyn Basin Project is a multi-billion-dollar development of the former Port of Oakland 9th Avenue Terminal located along the Oakland Estuary of California. A centerpiece of the development is the 10-acre shoreline park which will be built on a 1,200 ft long by 225 ft wide historic wharf. The wharf was built in the 1930’s on concrete and timber piles with a flat concrete slab. Prior to constructing the wharf, a rock dike was placed to protect the shoreline. The presence of the rock dike increased the hazards from lateral spreading of the underlying bay mud and non-ductile shear failure of piles driven through the dike. To open the park to the public, the wharf required a seismic retrofit in compliance with the California Building Code. The paper presents the results and conclusions of the following topics: • Structural condition assessment and repair strategies for the existing wharf deck, piles and jackets • Application of the California Building Code (CBC Ch31F) for the performance-based seismic evaluation of existing piers and wharves • Nonlinear pushover analysis of the wharf including the combination of inertial and kinematic effects • Impact of rock dike on lateral spreading and kinematic effects and the significance of existing piles in stabilizing the lateral spreading of the rock dike • Retrofit strategies for the wharf to meet the required seismic performance requirements per the California Building Code and reduce the demands on existing piles which were driven through the rock dike INTRODUCTION The 65-acre Brooklyn Basin Development project is located in Oakland, California. The project consists of 3,100 housing units, 200,000 sq. ft of retail and commercial space, along with various parks and public access improvements along the Oakland Estuary. A centerpiece of the development is the 10-acre Shoreline Park which will be built on a 1,200 ft long by 225 ft wide historic wharf. The wharf was built in the 1930’s on concrete and timber piles with a flat concrete slab. As shown in Figure 1, the wharf deck and piles support the 9th Avenue Terminal Building.

Jan 1, 2018

By D. R. Dolinar

The fall of small pieces of rock between roof bolts causes over 80 pct of the ground fall injuries in underground coal mines. Roof screen, if installed on the bolting cycle, can significantly reduce the number of these injuries. As the surface of the roof fails, the screen will have to retain the broken rock without failing or excessive deformation. Welded wire screen is the most common type of screen material used for roof surface control in underground coal mines. The load-deformation characteristics and the load capacity of welded wire screen were evaluated in the laboratory in a specially built test frame. In the frame, the square screen sections were held in place by bolts and bearing plates at the four corners while a center load was applied to the screen. The parameters evaluated included the wire gauge and configuration, the bearing plate loads and bolt spacing. The wire gauge of the tested screen was 4, 6, 8, 9 and 10. Maximum screen capacities for both load and displacement were developed for each of the wire gauge sizes along with the screen stiffness. This information can be used for screen selection and for the evaluation and determination of screen performance. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By George A. Lawrence, J. C. McHardy

"Field operating experience with an improved flotation mechanism for handling various flotation applications is covered in this paper. Some aspects of designing flotation machines are also presented. Operating data from extensive testing of commercial size equipment under actual plant operating conditions in the following applications is detailed:1. Copper Flotation2. Fine Coal Flotation3. Base Metal Sulfide FlotationDesign features, design improvements, modifications tested, and overall performance data are reviewed. Some mecl1anical performance data as well as metallurgical performance results are presented. Some comparisons with conventional flotation equipment are reported in this paper.Flotation sizing theories are reviewed and an actual equipment selection ex2.mple is presented. Scale-up criteria used for developing large cells are briefly covered.The paper concludes with a brief review of anticipated future flotation equipment design needs. IntroductionThe mining/milling industry is faced with increasing pressure to cut costs while maintaining product quality and indeed, in some instances, expanding production. For copper, nickel, iron, molybdenum, lead and zinc sulphides, coal, phosphate and some other minerals;, flotation remains the primary method of concentration and recovery of the valuable mineral away from the gangue. Cost reduction in flotation can be broadly focused on two areas:1. Flotation Chemicals2. Flotation Equipment"

Jan 1, 1985

By D. R. Dolinar

Geogrids can be used as surface control on both the roof and rib in underground mines to prevent the fall of small pieces of rock and material from between the primary supports. The use of screen material such as geogrid can significantly reduce the number of ground fall injuries caused by these small rock falls. Because of the potential for reducing injuries through the use of screen, the National Institute for Occupational Safety and Health (NIOSH) has conducted tests on screen materials including geogrid to determine their support characteristics and identify parameters that can affect their performance with respect to maintaining broken or failed rock. A specially designed test frame installed in the NIOSH Mine Roof Simulator (MRS) has been used to evaluate the load and stiffness characteristics of the screen material. Two types of geogrids with various designs have been tested-a polyester yarn and a polypropylene grid. The load-displacement characteristics of these grids were determined and the load capacity and stiffness were calculated through 20in of displacement. The load capacity and stiffness of the geogrid in general are shown to be related to the ultimate tensile strength of the screen material.

Feb 27, 2013

By Donald P. Tuchman, Justin R. Patts, Emanuele G. Cauda, Andrew B. Cecala, Elaine N. Rubinstein

Video techniques for monitoring exposure, such as NIOSH’s “Helmet-CAM,” employ both real-time dust monitors and mobile video cameras to assess workers’ respirable dust exposures. Many real-time personally worn dust monitors utilize light scattering sensing elements, which are subject to measurement biases as a function of dust type (size, composition, shape factor) and environmental conditions such as relative humidity. These biased and inaccurate dust measurements impair the monitor’s ability to properly represent actual respirable dust concentrations. In the testing described, instrument mass concentration data was collected using three different types of commonly used commercial off-the-shelf personal dust monitors and compared to a reference standard. This testing was performed in a calm air (Marple) dust chamber in which three units of each make and model (for a total of nine monitors) were used for each test. Equivalency factors (EF, a multiplier to match the Thermo TEOM 1400a reference instrument) ranged between 0.746 and 1.879 across all dusts and environmental conditions tested, and between 0.821 and 1.519 on the ISO test dust.

By Donald P. Tuchman, Justin R. Patts, Emanuele G. Cauda, Andrew B. Cecala, Elaine N. Rubinstein

Video techniques for monitoring exposure, such as NIOSH’s “Helmet-CAM,” employ both real-time dust monitors and mobile video cameras to assess workers’ respirable dust exposures. Many real-time personally worn dust monitors utilize light scattering sensing elements, which are subject to measurement biases as a function of dust type (size, composition, shape factor) and environmental conditions such as relative humidity. These biased and inaccurate dust measurements impair the monitor’s ability to properly represent actual respirable dust concentrations. In the testing described, instrument mass concentration data was collected using three different types of commonly used commercial off-the-shelf personal dust monitors and compared to a reference standard. This testing was performed in a calm air (Marple) dust chamber in which three units of each make and model (for a total of nine monitors) were used for each test. Equivalency factors (EF, a multiplier to match the Thermo TEOM 1400a reference instrument) ranged between 0.746 and 1.879 across all dusts and environmental conditions tested, and between 0.821 and 1.519 on the ISO test dust.

By David G. Almond

"Economies of scale and the variable characteristics of many large ore deposits have resulted in grinding installations having large SAG mills fitted with variable speed drives. Problems associated with effective operation of this equipment has created the need for better operator knowledge of mill load behavior and the need for new instrumentation capable of providing accurate information about load movement and composition. This paper discusses two performance enhancing instruments available to address these needs.INTRODUCTIONThe economic demands of new mining projects has resulted in increased equipment sizes and this is particularly evident in milling where there are now many SAG mills operating in the range of 28’ – 40’ diameter with installed powers of 8 – 22 MW. These mills are designed to process very high capacities of ore daily2 and the variable characteristics of many of the deposits mined results in the need to vary the mill speed during processing to cater for the changes in ore hardness. Mill speed changes often result in operational problems associated with high-energy impacts striking the mill liners reducing energy efficiency as well as degrading the grinding media through breakage, accelerating liner wear and in extreme cases even breaking liners. These operational problems have given rise to the need to have instruments aimed at providing operators with accurate information in real time about the load composition and movement within SAG mills.The original concepts for operating SAG mills were derived from past experience of operation of conventional fixed speed ball mills. However, the relatively stable conditions that applies with fixed speed and constant ball charge in ball mills supports theoretical approaches to the grinding process based on energy calculations such as Bond’s Work Index concept. Later a set of parameters Si and Bij were used for describing load kinetics, but all of these methods neglect the details of load movement and how the energy is actually used inside of the mill. It is now commonly accepted as a basic rule that SAG mills grind by impact whilst ball mills grind by attrition and consequently SAG mills are designed and operated to generate a large amount of impacts by the cataracting load without paying sufficient attention to where these impacts are actually occurring. Many mills are operated on the basis that as long as the mill is consuming the expected power there is little attention given to the class of bodies using this energy and this often results in the inefficient use of energy."

Jan 1, 2005

By J. R. Koehler

Although two-entry yield pillar-based gate roads supported by wooden cribs have been commonly used throughout longwalling in the Wasatch PlateadRoan Cliffs coalfield of central Utah, a three-entry yield-abutment gate road configuration was recently trialed in the Hiawatha Seam at the Genwal Resources (GRI) Crandall Canyon No. 1 Mine, near Huntington, UT. Pillar, entry, and cable bolt performance were monitored through second panel mining using a fairly extensive array of geomechanical instruments installed over a span of four crosscuts. Ground pressure and entry closure measurements confirmed that the 9.1-m-wide (30-ft) yield pillar was partially shielded from first panel longwall loads by the 36.6-m-wide (120-ft) abutment pillar, and consequently, experienced only minor yielding until the approach of the second panel face. Complete yielding of the 9. I-m-wide (30-ft) pillar occurred when the second panel was approximately 6.1 m (20 ft) inby the instrumentation site. Average cable bolt loads and differential roof sag remained low through second panel mining and tailgate entry ground conditions were excellent; however, very high ground pressures in the abutment and yield pillars, and second panel rib strongly suggest a high potential for coal bumps utilizing this gate road configuration at mining cover depths in excess of 396 to 457 m (1300 to 1500 ft). This conclusion is supported by the suspected occurrence of small coal bumps along the abutment pillar ribs, observed indirectly as fresh debris in the middle entry just behind the second face. This paper presents a case history developed from the geotechnical measurements and on-site observations of this unique application of a yield-abutment gate road configuration and cable support system in the Hiawatha Seam.

Jan 1, 1996

Nowadays, technology has improved to extract dimensional stone blocks at quarry sites and also to process these at processing plants for making slabs and tiles. In the process of quarrying and processing, performance evaluation of machinery is very important to achieve optimum output at minimum cost with improved technology. Cost analysis of improved technology includes parameters such as manpower, energy consumption, tool consumption, depreciation, maintenance and also others. The chainsaw machine with long boom and rail in marble quarries and multi-diamond wire saw machine for slab making from granite blocks at processing plants have recently been introduced in India. Thus, a study was carried out under a research project on these machines to assess their suitability. In this paper, performance evaluation and cost analysis of chainsaw and multi-diamond wire saw have been carried out with existing machines on the basis of research findings.

Dec 6, 2010