Search Documents

By J. E. House, J. L. Drobnick, R. R. Swanson, D. W. Agers

The paper describes an improved process for the recovery, purification, and concentration of copper values from acidic dump leach liquors. The process employs a new liquid ion exchange material (LIX® 64 reagent) capable of separating copper values from iron and other impurities common to dump leach liquors in the typical pH range of 1.4-3.0. Properties and performance of the reagent are discussed. Design scale-up information for both pilot plants and commercial installations, including preliminary economics, are presented. Economic considerations include the production of electrolytic copper from the purified copper aqueous concentrate. INTRODUCTION Since the commercial acceptance of the liquid ion exchange process in the mineral processing industry, it has been predicted that a wide selection of chemical reagents to efficiently and economically separate many metals in solution under a wide range of conditions would be commercially available. Several years ago, General Mills began a basic research and development program to determine if it were possible to develop a reagent to extract economically metallic ion from existing process streams. Progress toward reaching this objective was reported in late 1963, when development of quantities of LIX -63 reagent, a highly selective reagent for the extraction of copper, was introduced. The properties of this reagent are described in a previous paper.' The development work with this reagent indicated that perhaps the largest potential application for a copper extractant, the treatment of acidic dump leach liquors, would not be economically possible with LIX-63 because of limitations of the reagent to extract copper below a pH of 3.0. The relatively small pH adjustment required with LIX-63 would result in a significant processing cost and the undesirable precipitation of ferric hydroxide from the liquor. This pointed to the need for another copper extractant which would extract copper from dump leach liquors without pH adjustment. General Mills was successful in synthesizing a molecule which does not have the pH limitation of the LIX-63, yet possesses the selectivity-solubility properties required of a metallic extractant. The resulting LIX-64 reagent broadens the pH range from which copper can be effectively extracted and separated from other metallic impurities. Of special significance is the fact that the reagent, LIX-64 was developed by combining the technical requirements of a specific problem in hydro-metallurgy with theoretical organic and physical chemical principles.

Jan 1, 1967

By U. N. Bhrany, N. Arbiter

Over the last one hundred years the problem of assessing the efficiency of energy consumption in producing rock breakage has been studied by many investigators from a variety of viewpoints. Their contributions fall into three main categories: (1) those characterized by a priori assumptions of a relation between the energy required for fracture and the degree of fragmentation produced (e.g. Rittinged(l), Kick(2) Bond(3)); (2) those studying simple systems with controlled energy applications (Gross(4)?(5) ); (3) those treating operating data to develop practical relative measures of efficiency (Coghill(6), Taggart(7)). Closely involved in the efficiency problem is the characterization of size distributions produced by comminution. Unless an experimental size distribution can be approximated by a distribution function and its constants, it becomes difficult if not impossible to develop quantitative energy-particle size relationships. While many such functions have been proposed, none are both completely adequate and convenient. The simpler fonns usually describe only a part of the sizing data, while those which apply to a greater extent are cumbersome(8). The thesis underlying the study here reported can be stated as follows: Size reduction in a tumbling mill subjects ore particles to a relatively constant fracture-producing environment. The intensity of the forces is determined by such factors as the mass of the breaking bodies (rods, balls, rock), and the speed and dimensions of the shell. For a particular ore the extent of size reduction will depend both on the intensity and on the duration of exposure. The latter is the residence time in a batch mill, or is determined by the effective volume and the flow rate in a continuous mill. Size reduction can thus be regarded as a rate process in which the weight of material in size intervals varies as a function of grinding time. Although both the rates of disappearance of coarser sizes and

Jan 1, 1961

By E. J. Roberts

Hydrometallurgical operations and many processes in the chemical industry require the separation of dissolved material from solids. One of the decisions which has to be made in designing a plant for such an operation is how this separation shall be accomplished. It is the purpose of this paper to set forth the general principles involved in such separations in order that the optimum flowsheet and equipment may be selected. Countercurrent Decantation with thickeners, or C.C.D. as it is generally known, is, of course, only one way of separating dissolved material from undis-solved. Other unit operations such as Countercurrent Filtration (C.C.F.) and Countercurrent Classification (C.C.C.) are widely used. The same principles may also be applied to centrifugally assisted decantation, as with nozzle or solid bowl type centrifugals, and to separations using screens, either gravity or centrifugal type. Another form of countercurrent washing applicable to granular materials is practiced in continuous ion exchange operations. All of these operations depend on two basic principles, or combinations of these principles. In C.C.D. type operations the solids are concentrated into the smallest possible volume of liquor in each step and the resulting pulp then mixed with a more dilute liquor and recon cen trated, the liquors separated from the more dilute stages being advanced to dilute the more concentrated liquor in a previous solids concentrate, as is shown in Fig. I. This will be termed the solids concentration-solution dilution principle, or, for short, solution dilution. countercurrent decantation- type circuits. The second principle used in washing solubles from solids is that of solids concentration-solution displacement. Here the solids are restrained from movement while wash solution is forced through the interstices in a counter-current fashion, as in Fig. 2. In the simplest application of this principle, once the "cake" has been formed, it is not disturbed until the operation is completed. In continuous filters, the cake is merely moved under the successive washes and the displaced filtrates removed as in Fig. 4. Often, however, after one or two displacement washes, a repulping step is introduced, the cake reformed and washed again. This procedure brings the solution dilution principle into play as well as the solution displacement principle. Merely thickening ahead of filtration, which is often operationally advantageous, does not hybridize he circuit. It still can be a pure solution displacement operation from the washing

Jan 1, 1961

By O. E. Palasvirta

Several drum-type, low-intensity dry magnetic separators have recently been described 1,2,3,4 all of which share at least two generic similarities. The magnet consists of a multiplicity of poles of alternating polarity and, the speed of the drum shell, relatiw to the magnet, is such that the magnetics are agitated through rotation of the magnetic particles around their individual axes. The speed of the drum relative to the magnet (differential speed) determines the frequency of the field reversals. For effective agitation this frequency generally has to be above a specific value, which varies according to the mean particle size of the magnetics. With separators of small diameter, say less than 11/2 ft., a sufficient differential speed for treatment of fine magnetite can be attained only by rotating both the magnet and the drum separately; separators of large diameter may attain sufficiently high differential speeds with stationary magnets. Separators of large diameter thus have the advantage of simplicity of design. The capacity of a separator of this type is directly proportional to the speed of the shell. As the centrifugal force opposing the magnetic force increases at a slower rate than the peripheral speed of the shell when drum diameter is increased, large drums can be operated with higher peripheral speeds. Thus they have a higher capacity than smaller drums. Separation is also a statistical phenomenon, i.e. the grade of concentrate improves as the number of agitations or rotations of the magnetic particles per separation increases. As separators of large diameter have space for a large number of magnets they are best suited for production of optimum grade concentrate. The statements above are general clues For separator design. In the following an expression IS derived showing a more exact relationship between the pertinent separator variables. As both magnetic attraction and centrifugal forces are directly proportional to the volume of the affected bodies, complications in mathematical analysis, arising from variable particle size, are avoided by considering the force per unit volume of affected material. For the magnetic force per unit volume Runolinna (3) gives the following equation: V " 1 + N(ur, - 1) uo dr (1) where ur and uo stand for the relative permeability and the permeability of vacuum, respectively, N is the demagnetization factor, B the intensity of the magnetic field, and r the distance from the face of the magnetic pole. The permeability of a specific magnetite ore can generally be considered as a constant. For ground, liberated material N can also be treated as a constant, and the first simplification can be made by writing ur-1 1=k1. 1 + N(ur - 1) uD k1. Fig. 1 shows the field intensity curves for two U-magnets of different size, but of roughly similar geometry of cross-section as plotted against the distance from the plane of the pole faces. The curves

Jan 1, 1961

By C. H. Wayman, D. W. Fuerstenau

The effect of bubble size and concentration of certain reagents on the terminal velocity, shape, path, and drag coefficients of single air bubbles in distilled water has been investigated. Bubbles of a certain size range rise considerably faster than Reynolds number-drag coefficient relationships predict, whereas a small amount of frothing agent reduces their terminal velocity. The rapid velocity at which bubbles rise in distilled water appears to result from slip at the boundary and from circulation within the bubbles. Surface-active agents retard bubble motion through prevention of both circulation and slip at the boundary. A surface tension concentration gradient helps maintain bubble sphericity. HE gas phase is one of the indispensible in-gredients in flotation operations. Flotation depends on the collision of an air bubble and a mineral particle in a pulp and their ability to remain in contact long enough for adherence to take place. Before it is possible to understand the mechanics of air bubble-mineral particle encounter, it is necessary to learn more about the nature of bubbles themselves before collision with a mineral particle has taken place. To date, little work has been done on air bubbles in flotation systems. In 1945 Fahren-wald' presented a study of the role of frothers on air bubbles and on aeration in flotation, and recently Wark and Sutherland' discussed the work of Rosenberg- in relation to flotation. The research reported in this present article was undertaken to investigate systematically the effect of bubble size and the concentration of certain reagents on the terminal velocity, shape, path, and drag coefficient of single bubbles in distilled water. Most of the work is concerned with the effect of a-terpineol on bubble motion in water, but studies were made with potassium chloride, potassium hydroxide, potassium ethyl xanthate, and potassium amyl xanthate. Experimental Method and Materials: To obtain free bubble rise and reduce wall and surface effects, the investigators used a tank of 5½x5½x30-in. internal dimensions, filled with water to within 4 % in. of the top.' The tank was made of acrylic plastic so that the walls would have good optical properties. Distilled water, which was re-distilled in a block tin still and saturated with air before each test, was used in all the experiments. All solutions were made with reagent-grade chemicals. During each experiment the water was at room temperature, and during the course of an experiment the temperature did not fluctuate more than 0.5°C. Since the experiments were performed over a period of six months, the temperature varied between 25° and 27°C. The temperature at which each series of experiments was conducted is recorded with the data. The experimental apparatus is presented dia-grammatically in Fig. l. Individual air bubbles were generated from purified compressed air through a capillary of 0.003-cm internal diameter at a rate

Jan 1, 1959

By F. Petkovich, M. P. Sudbury

Development of a new method of treating flotation concentrates for the preparation of feed suitable for direct charging to blast furnaces or converters is described. The method takes advantage of the fact that pyrrhotite contained in the concentrates can be made to undergo exothermic reactions which, under properly controlled conditions, result information of oxidation products that serve to cement the concentrate particles together. Thus green concentrates either in the form of pellets or briquettes containing 5 to 8 pct moisture not only were hardened, but also completely dried autogenously by continuous countercu,vrent shaft treatment with air. The process was developed through pilot plant operations ranging from 35 1b per hr to 2.5 tph, culminating in products evaluation tests on a railway-car scale. Falconbridge Nickel Mines Ltd., Falconbridge, Ont., have practised sintering, on a travelling grate machine, for many years to prepare a pyr-rhotite-bearing Cu-Ni sulfide flotation concentrate for blast furnace smelting. In recent years the development of new mines, and the construction of concentration plants some 40 miles from the smelter has increased the quantity of concentrate shipped, and encouraged the search for a method of producing dry, hard pellets or briquettes suitable for direct charging to a blast furnace or converter, and capable of withstanding considerable handling. The cementing properties of pyrrhotite oxidation products were discovered during a search for a suitable agglomeration method for sulfide concentrates, and were exploited in a process subsequently developed for autogenously drying and hardening pellets and briquettes of pyrrhotite-bearing Cu-Ni sulfide flotation concentrate. EARLY TEST WORK The production of hard, dry pellets of concentrate filter cake was attempted in the drying plant of one of the new concentrators. While soft pellets were produced containing 5 pct moisture, attempts at further drying resulted in disintegration of the pellets and intolerable dusting. The plant therefore was controlled to produce a concentrate containing about 6 pct moisture. The partially dried concentrate, which was shipped to Falconbridge for sintering, tended to heat spontaneously in transit. An at- tempt to briquette the moist concentrate at Falconbridge, in a plant incorporating a muller, a 20-in. roll briquetting press, and a steam-heated travelling grate oven, was more successful, although the equipment corroded rapidly due to the acid nature of the concentrate after spontaneous heating had occurred. LABORATORY STUDIES OF SPONTANEOUS HEATING OF CONCENTRATE The spontaneous heating of partially dried concentrate was studied in the laboratory. Moist concen-

Jan 1, 1961

By H. R. Cooper

Beginning from the point of view that process control of ore flotation can be approached by on-line analysis of processing behavior, an equation was developed which has characteristics useful for a multi-variable feedback loop. The application of this equation to optimizing control with a data acquisition system will be discussed in Part 11. OBJECTIVE OF CONTROL The purpose of developing a feedback method for concentrator control is to provide a means for determining ore processing behavior in order that data describing the ore can be used to make appropriate changes in control conditions while the ore continues to flow through the flotation circuit. In absence of simple linear relationships between pairs of variables in the flotation process, attention is directed to the need for a generalized relationship which possibly would incorporate all pertinent variables. It would be possible to apply such an equation to the control of variables in a concentrator in real time according to operational requirements as ore gradually changes in quality and processing behavior. To meet this objective, it is necessary to define relationships describing flotation performance in terms of performance variables capable of being measured on-line, either with on-line instruments and analyzers or with manual methods lending themselves to quick determination of meaningful information. Relationships derived to meet this objective form a model for the flotation process. The evaluation of flotation parameters of the ore and the execution of control on the basis of the derived information while the ore is continuing through the process would constitute a feedback control system. Data for the following control and performance variables can be made available: 1) ore feed rate, 2) collector addition rate, 3) lime addition rate, 4) pulp density, 5) assay or multiple assays in feed, tails, or concentrate sufficient for material balancing, 6) particle size distribution in flotation feed, 7) froth height, and 8) frother addition rate. Other process variables, such as flotation air input and mechanical agitation intensity, are usually not considered as control variables and were not taken into account in this analysis. Other data, such as that describing the ore, would be useful for concentrator process control. However, information of this type (such as ore hardness, grain size of the mineral, chemical species of the mineral, and ore surface properties) being not presently measurable in the on-line sense, has the effect of causing disturbances in the system which can be detected only indirectly. The process control system being sought must recognize disturbances by their effect on measured performance followed by determining control changes to compensate for them in meeting the objectives of improved performance (perhaps higher throughput, maximum return, etc.). A suitable model for the process having capability of recognizing the effects of ore disturbances should provide the means for introducing proper compensation through control changes. This would be done by processing on-line data with the model to calculate coefficients reflecting ore characteristics. This procedure can only be applied in a typical flotation system when on-line data can be processed at faster rates than the usual rate at which the ore in flotation feed takes on significantly different characteristics. For example, material balance data can be accumulated in approximately 5-min intervals using on-line X-ray fluorescence analysis. The flotation system time constant might be 15 min including grinding. Ore changes having time constants longer than 1 hr could be accommodated using on-line feedback control by this procedure. FORM OF A FLOTATION MODEL A suitable form for mathematical expression of the flotation process is an equation involving rates, when each of the components entering into the separation can be treated independently by a rate equation. A first-order, kinetic rate equation can be written on

Jan 1, 1967

By S. R. B. Cooke, H. S. Choi, I. Iwasaki

In a previous article1 the function of various fatty acids as collectors for iron ores was reported for the two alternate processes; (a) the flotation of iron-oxide minerals, and (b) the flotation of calcium-activated siliceous gangue. The selectivity of separation was shown to be markedly dependent not only on such common parameters as pH and the levels of collector and activator addition, but also on the structure and the degree of unsaturation of the acids used. The iron ores employed consisted primarily of hematite, goethite, and quartz and as the effectiveness of any one acid on the separation depends on the individual response of each constituent mineral toward the given collector, a comprehensive knowledge of the floatability of the individual minerals is desirable for the interpretation of the results obtained. The mechanism by which a collector ion becomes attached to a mineral-solution interface has been a subject of much investigation. From quantitative studies of the properties of the electrical double layer on mercury2 and on several solid surfaces3,4,5,6 , the adsorption of some flotation reagents at the mineral-solution interface is beginning to be understood. For example, it has been demonstrated from streaming potential measurements made on quartz5 and corundum6 that the interfacial electrical condition is strongly dependent on the pH. Thisoccurs presumably through the following electrolytic reaction at the interface, and in the presence of a flotation collector, controls the floatability of the solids. A concurrent investigation of the flotation behavior of goethite and of quartz carried out at the School of Mines and Metallurgy7 has shown a positive correlation with the electrokinetic behavior of these minerals. The purpose of the present investigation was to collect general information on the floatability of hematite, and to investigate the function of various 18-carbon aliphatic acids on the floatability of hematite, goethite, and of activated quartz. Electrophoretic mobility measurements, simplified flotation tests using a modified Hallimond tube, and contact angle and frothability measurements were employed. The results are of direct application in the interpretation of the batch flotation results on natural ores as

Jan 1, 1961

By Olav Mellgren

Part I. The interaction between potassium ethyl xanthate and lead salts has been studied thermo-chemically. It is shown that ethyl xanthate reacts with lead carbonate, basic carbonate, thiosulfate and sulfate according to principles of simple chemistry, whereas reactions with lead sulfite, metasulfite, basic thiosulfate and hydroxide at high pH are associated with secondary reactions. A new compound "xanthogen thiosulfate" is postulated. Part 11. Adsorption of ethyl xanthate on galena has been studied quantitatively and thennochemi-cally. It is shown that an ion-exchange mechanism governs the adsorption process and that the heat of adsorption of xanthate on galena is equivalent to the heat of reaction of ethyl xanthate with bulk lead salts. It is concluded that the entropy content of the surface "compound" on galena is different from that of a corresponding bulk lead salt. Alkali depression is in part shown to be due to the instability of the xanthate-galena system at high pH and to the formation of basic lead salts. Sulfate and carbonate ions are shown to have a stabilizing effect on the xanthate-galena system. PARTI. THERMOCHEMISTRY OF ETHYL XANTHATE AND OF ITS REACTION WITH LEAD SALTS In the past little attention has been paid to the chemistry of lead xanthate. It is known that xan-thates form slightly soluble compounds with lead and that suspensions of lead xanthates in alkaline solution decompose rather readily.' The solubility of lead ethyl xanthate is of the order of 2.6 x 10-6 moles per 1. At increasing pH the xanthate concentration of a saturated solution contains more xanthate. Thus at pH 11 this xanthate content is about 100-fold larger than at pH 7.1 Xanthates are known to be consumed when added to a suspension of slightly soluble lead salts such as lead sulfate and lead carbonate. It is unknown to what extent this xanthate consumption is due to a simple chemical reaction because, frequently, observations are made which reveal secondary reaction products in such reactions. Thermochemical study of the reaction between xanthate and lead salts offers a means to clarify the significance of these reactions as the enthalpy changes can be accurately predicted from heat of formation of lead salts in pure solution reactions. In the present work the heats of formation of lead ethyl xanthate from potassium ethyl xanthate and lead salts are determined and some thermochemical aspects of xanthate in solution are studied. The results of these investigations are presented in Part I. In Part II the heat of adsorption of ethyl xanthate on galena surfaces is presented. All enthalpy changes were measured directly in a microcalorimeter. Calorimeter: The calorimeter used for measuring enthalpy changes was similar to that used by Redinha and Kitchener2 which was based on a description by Derbyshire and Marshall.3 Other useful references4,5 are listed. A sketch of the calorimeter

Jan 1, 1967

By M. E. Wadsworth, T. D. Chatwin

The kinetics of sulfidization of hematite (Fe203) by H2S gas at various partial pressures have been determined over the temperature range of 170° to 500°C. The process was controlled by thin films of pyrite (FeS2) and troilite (FeS) which were protective and formed diffusional layers. At higher temperatures the thermodynamic drive to form FeS2 decreased, and consequently the rate of formation of FeS, decreased. Conditions for the development of thin layers of FeSz consisting of 10 to 100 atomic diameters are presented. Laboratory flotation results on synethetic ores indicate floatability identical to that of pyrite of normal xanthate flotation. The prospect of high-temperature sulfidization of metal oxides using H2S, S, or other sulfur bearing compounds is intriguing as a potential activation process for flotation since the thermodynamics are very favorable for a large number of systems. If the kinetic parameters are sufficiently well understood it may be possible to provide surface sulfide layers a few angstroms thick, thus imparting normal sulfide floatability characteristics to the oxide. For thin layers the total sulfur pick-up would be small except for very high surface area materials but in most cases this sulfur could be readily removed by roasting if necessary. The general reactions for the sul-fidization of metal oxide MxO, to a metal sulfide MpSq using H2S may be written for the three conditions py > xq; py < xq; and py = xq: A large thermodynamic advantage is obtained in many systems because of the relatively large negative free energy of formation of H,O compared to H,S. For the temperature range 2S° to 1500°C &apos; where AFOis the standard free energy and T is absolute temperature. As is evident from Eqs. 4 and 5, the free energy of formation of H ,0 is approximately 35 to 37 kilocalories per mole greater than that for H,S over broad variations of temperature. For oxide-sulfide systems as outlined above, sulfidization may be expected to occur for the conditions: Groups I and 111: that is, if the terms on the right are more negative than those on the left the reaction is expected to occur thermodynamically. The value hFg,(,) is included in Eq. 6 since hFLzs is based upon gaseous S2 rather than the normal reference state, orthorhombic sulfur. The

Jan 1, 1969

By J. F. Shea, O. F. Tangel

Battelle Memorial Institute participated in a program for the General Services Administration aimed at developing a nickel-cobalt separation process that could be integrated in the Nicaro nickel plant. At the time the programwas being carried out, the Nicaro process was a straight-through operation, in which the ore was reduced and leached, after which the pregnant solution was boiled to produce a so-called "bulk precipitate" which contained virtually all of the nickel and cobalt which had been dissolved in the leaching step. The weight ratio of nickel to cobalt in Nicaro ore is approximately 15 to 20:l. The weight ratio of nickel to cobalt in the finished product had to be 100:l or higher to meet specifications. Because the Nicaro process embodied no nickel-cobalt separation step, the only way that a bulk precipitate of the specified nicke1:cobalt ratio could be produced was to so adjust roasting and leaching conditions that nickel would be selectively leached and most of the cobalt would be rejected with the tailings. The required selectivity, however, was achieved at the expense of nickel recovery, which was 5 or more per cent less than might have been obtained with the existing equipment, utilities, man power, etc., had selectivity been no object. The over-all purpose of the program was to develop a separation step that could be fitted into or onto the Nicaro facilities and which would permit the manufacture of a product that would meet the desired specifications and still permit the recovery of a maximum amount of nickel. Battelle suggested that this might be accomplished by reprocessing off-specification bulk precipitate and specifically suggested the process based on ammonium sulphate leaching followed by hydrogen reduction of the leach solution according to techniques developed commercially by Sherritt Gordon Mines Limited. Such a process would not only satisfy the objectives of the research but would present two additional advantages. (1) It would produce a separate cobalt product which could be further processed into metal, alloys, oxides, or salts. (2) It would yield nickel in metallic form which might be more generally marketable and command a slightly higher price per unit of nickel than the Nicaro oxide product. DESCRIPTION OF THE PROCESS Figure 1 is a flowsheet of the process. The essential features are: (1) Extraction of about 97 per cent of the nickel and about 85 per cent of the cobalt from bulk precipitate by a principal leach with ainmonium sulphate solution (Step A). Extraction of virtually all of

Jan 1, 1961

By J. E. Forciea, O. E. Palasvirta, L. G. Hendrickson

AH pilot and commercial plants working with Mesabi Range taconite employ wet magnetic separation. Progress is being made with a dry magnetic process, but this has not yet been applied to taconite except in the laboratory and pilot plants. Flowsheets in all five plants are similar, including multiple stages of grinding, each followed by magnetic separation, which rejects a finished tailing. The flowsheet in Fig. 1 is used in the preliminary and commercial plants of the Erie and Reserve mining companies and in Unit C of Oliver&apos;s Pilotac plant. At Erie the desliming operation is omitted. In the Reserve plants two ball mills are used with each rod mill. Pilotac uses flowsheet 2 in Unit A-B and has also tested flowsheet 3. Principal differences in the three flowsheets are the number of grinding stages and the type of roughing. The terms open-circuit roughing and closed-circuit roughing are best defined by the diagrams. Special Test Data Given in Table I: For the Erie and Reserve commercial plants, Table I reflects routine conditions. Pilotac, the experimental plant, has been run with several flowsheets, including those followed at Erie and Reserve&apos;s commercial operations. Pilotac data for these last two flowsheets are similar to commercial plant results and are not repeated in Table I; statistics are given, however, for special test conditions. using other flowsheets. when the objective was to &apos;to extra-grade concentrate, Variations Among Taconites: Although crude ore tributary to these plants is generally classified as taconite, there are important differences in mineralogy and fineness of dissemination.

Jan 1, 1959

By A. M. Gaudin, J. H. Brown

In a survey of the effects of heat treatment on the comminution of various rocks, it was found that unusual size distributions often characterize the broken products, and that this is related to a great increase in intergranular fracture1. It is the purpose of the present paper to contribute to an understanding of this effect. In a thesis by one of use, critical consideration was given to many mechanisms which could conceivably be responsible for the increased intergran-ular fracture. It was shown that neither gross chemical changes nor intergranular corrosion are required. Among non-chemical mechanisms the most likely appeared to be (1) Uneven expansion due to thermal gradients, giving spalling (2) In a manner similar to that prevailing in metals, the appearance at high temperature of intergranular weakness. (3) Unequal thermal expansion of adjacent grains. Experiments were designed and conducted to permit a choice among the many alternative mechanisms and in particular among the three listed here. EXPERIMENTAL MATERIALS Tests were made on the materials listed in Table 1. Of each material, only lumps similar in composition and grain size were used. The three marbles listed in Table 1 were analyzed to assure that their chemical compositions did not differ greatly (Table 2). On the basis of the chemical analyses, of differential thermal analyses, and of X-ray powder diffraction patterns, it appeared that the marbles were very similar except for their grain sizes.

Jan 1, 1961

By H. E. Lee, D. Ingvoldstad

AT Bunker Hill the original charge storage and preparation system was installed in 1917 to accommodate lead-silver gravity mill products. Only minor tonnages of wet fines such as vanner and flotation concentrates were received. Charge flux and diluent requirements were provided by an ample supply of siderite middlings and coarse lime-rock. While oversize material was crushed through %-in., the use of roll crushers in series resulted in a more or less granular, free-running charge of adequate porosity. Under such conditions, receipts could be proportioned directly from receiving bins, and suitable blending was obtained by passing the resultant layered composite through a small Stedman disintegrator. This elementary system served well for production and smelting of an extremely lead-rich sinter, in the low column blast furnace. Here sinter physical quality is less critical, and appreciable quantities of raw flux and oxidized ore may be charged directly to the blast furnace without seriously impairing furnace capacity. Prior to 1938 the relative proportions of zinc receipts were low and extraneous flux requirements at a minimum. However, subsequent war-inflated zinc demands brought marked increase in fine concentrate and slimy zinc leach residue receipts and an abrupt introduction to smelting a more refractory zinciferous charge. The higher temperature demands of the more refractory zinciferous charge required a higher smelting column and the higher column, in turn, rendered the blast furnace less receptive to improperly prepared feed. Inadequate presinter processing facilities prevented the production of acceptable sinter, and blast furnace production declined to 50 pct of former capacity. In view of a prevailing contention among lead metallurgists as to the deleterious action of high zinc slag on blast furnace capacity, it was natural to overstress this factor and to concentrate on possible changes in furnace design. Another interpretation was that primary correction should be sought through expanded sintering facilities. This divergence of opinion, together with the extreme material shortages of the 1940&apos;s, delayed corrective

Jan 1, 1957

By A. Alonso, J. Daubenspeck

In the nickel extraction process at Nicaro, Cuba, dried and ground nickel bearing laterites are reduced at 1300-1400F in multiple-hearth furnaces. Nickel is leached from the reduced ore by aeration in an aqueous solution of ammonium carbonate. Nickel carbonate is precipitated from the liquor and calcined to yield nickel oxide. The following are the more important modifications of the Nicaro process since plant rehabilitation and expansion. Ten percent increase in tonnage was achieved without decreasing the fineness of the ore by minor mechanical modifications of the grinding plant. Another five percent increase in tonnage was attained by intentionally overloading the ore prepration and leaching circuits in an effort to control cobalt extraction. Modifications at the sintering plant allowed it to handle the entire output of the expanded plant. A fifty percent increase in leach liquor cooling facilities alone provided an increase in nickel production of five percent. Stronger fresh leach liquor for increased nickel washing efficiency was obtained through improved distribution of water to the ammonia absorption towers. Advantage was taken of the reduced calcine&apos;s capability to precipitate cobalt, and modifications in the leach liquor circulation provided controlled cobalt solubility with minimum harm to nickel extraction. Several process changes at the drying plant brought about a ten percent reduction in the fuel oil consumption at this pint. Controlled air addition to the reduction furnaces&apos; upper hearths burned formerly wasted combustibles thereby reducing oil consumption by twenty percent. The nickel extraction process successfully emplayed on the extensive but lowgrade lateritic ores of Eastern Cuba at the U. S. Government owned Nicaro plant, has been previously described in various publications. The large mine and plant operated by the Nickel Processing Corporation, located on the northeastern shore of Oriente Province, have been recently expanded to a yearly capacity of about 50 million pounds of nickel. Essentially, the operation involves open pit mining of a limonite-serpentine ore mixture containing 1.3 to 1.4 percent nickel and 34 to 38 percent iron. The comparatively lumpy, wet (25 to 30 percent moisture) ore is first dried and ground prior to chemical treatment, to which the entire 7,000 tons per day feed must be subjected. In the initial chemical action the dried and ground ore is reduced with carbon manoxide and hydrogen at 1300-1400° in multiple-hearth furnaces. The resulting metallic nickel is selectively leached from the reduced calcine by aeration in an

Jan 1, 1961

By S. A. Falconer

The benefication of non-sulfide or non-metallic minerals by froth flotation has been practiced commercially for at least 30 years. In the pioneer stages of development of this flotation art, most of the promoters investigated were fatty acids or soaps that had been found to float sulfide minerals. When commercial application of froth flotation started to assume importance in the late 1920&apos; s and 1930&apos;s, a great deal of fundamental research work was done in the laboratory (11-14, 19, 22, 23, 26, 29, 32). Among other subjects, this work included studies of the relative effectiveness of the different fatty acids and their salts on the flotability of various non-sulfide and non-metallic minerals. The successful present-day use of fatty acid and petroleum sulfonate type promoters results from better understanding of the principles of non-sulfide flotation plus the developnent of effective selectivity modifying agents. Many investigators have contributed to a greater appreciation of the numerous interrelated factors involved in fatty acid and soap flotation of non-sulfide minerals. Of these, mention should be made of recent fundamental studies by Tagart and Arbiter (31); Wolstenholme and Schulman (35); Schulman and Smith (28); Wark and his co-workers(3,4) Du FIietz(l5); and J. Leja(24). According to J. Rogers, K. L. Sutherland and E. E. and I. W. Wark(27), "the basic requirements for a &apos;collector&apos; in flotation are that it shall form a film over the surface of the mineral to be floated and that this film should be oriented so that hydrocarbon (non-polar) groups form the effective surface." When modified in that way, the mineral surface possesses some degree of air avidity. All investigators would agree with Taggart, Taylor and Ince (33)that such a film can be produced only if the collector compound contains an active (polar) group to be attracted to the mineral surface, as well as the non-polar group. The commonly used anionic-type promoters for non-sulfide, non-metallic and metallic oxide ores include: 1. Fatty acids, and their soaps and emulsions. 2. Fatty acids residues — "pitches" and "foots." 3. Sulfonated and sulfated fatty acids and so-called "petroleum sulfonates." 4. Paraffin chain salts — sulfonated and sulfated higher alcohols. 5. Cyclic organic acids or salts, such as naph-thenic acid and naphthenates. Certain fatty acids are more effective than others as promoters for particular minerals under certain specified conditions. Some of the more costly fatty acids or collectors of the paraffin chain salt type may give improved selectivity in some instances and are being used commercially in a limited number of operations. Local availability may dictate the choice of the fatty acid used — for example, the use of palmoil fatty acid for flotation of copper carbonate ores in the Belgian Congo. Coconut oil fatty acids have also found limited use.

Jan 1, 1961

By R. B. Booth, W. F. Linke

The continuous interest of the American Cyanamid Company in producing superior polymeric flocculants and dispersants for the mining industry has resulted in a broad, general study of the physical chemistry of mineral-polymer systems. The aim of this program has been to establish a sound theoretical basis on which practical problems could be analyzed, and which would lead to the development of new and improved flocculating and dispersing agents. This study has required the cooperative effort of physical, analytical, and polymer chemists, as well as engineers familiar with mining problems. This report summarizes the results of some of our investigations over the past two years. Further studies along these and other lines are in progress and will be reported in the near future. MEASURING FLOCCULATION IN THE LABORATORY The foremost problem in studying flocculation in the laboratory has been to establish reproducible methods of comparing and evaluating the effectiveness of various reagents. Previous workers have measured settling -rates 1,8 filtration rates2 , and sediment volumes3 . Direct observations of the floc size, or the clarity of the supernatant liquid, can also be used. AIthough these parameters are all interrelated, they do not always measure the same physical properties of the suspensions, and hence are not equally useful or reliable. Whatever the method of comparison selected. the testing procedure must be carefully defined and standardized. The results must be satisfactorily reproducible, and for practical purposes must accurately reflect the results obtained in mill use. In order to compare the data obtained in these various types of test, the physical nature of the flocculated system must be examined in some detail. In an unflocculated system, only the larger or denser particles (the "sands") settle at a useful rate. The sediment can be observed to build up from the bottom of the cylinder, while the fines remain in suspension for a long period of time. If the system is not disturbed, even the microscopic fines can be seen to classify themselves as they fall over a period of days. When a high molecular weight polymer is added to the system, the colloidal particles are tied together randomly in flocs, and the sands and fines settle together. The line of demarkation between solid and liquid phases moves downward from the top of the cylinder. The settling rate of the flocs depends on their size and on their effective density. For a given mineral sample, the larger the flocs, the faster the settling. Since the large flocs cannot pack as closely as small ones, they produce a sediment with more pore spaces, and hence of larger volume, which is easier to pump and to agitate. Although it is nearly impossible to measure individual floc sizes, it is relatively easy to determine settling rates and sediment volumes. Of these two, the settling rate is simpIer to measure, and hence generally more practical. Reproducible sediment volumes can only be obtained by allowing the solids to pack for a rather long period of time (e.g., hours to days), and although the volumes thus observed are directly related to the degree of flocculation (average floc size), it is often impractical to wait so long for the results.

Jan 1, 1961

By P. Somasundaran, D. W. Fuerstenau

This article presents the results of an analysis of grinding of 1:1 mixtures of 4x8-mesh quartz and limestone in laboratory ball and rod mills. From these experiments, the amount of energy consumed in grinding each component of the mixture was determined. In the ball mill, limestone consumes slightly more energy than quartz in the initial stages of grinding, but as the grinding proceeds quartz begins to consume a slightly greater fraction of the energy. The postulate that the fraction of energy consumed by any material in a ball mill is proportional to its volume fraction has been shown to be approximately true. On the other hand, in a rod mill energy consumption by quartz and limestone is equal only in the initial stages of grinding, with energy consumption by quartz greatly exceeding that by limestone as rod milling proceeds. Preferential energy consumption in tumbling mills has been discussed in a number of papers. For example, from an analysis of the kinetics of comminu- tion in ball mills, Arbiter and Bhrany&apos; obtained rate equations based on the postulate that only coarse particles are ground, indicating that fine particles are protected from the action of the balls by coarser particles. In rod mills this protective action is much more pronounced than in ball mills. Recent studies on the rod milling of limestone-quartz mixtures have shown that this protective action causes the mineral with the lowest grindability (quartz in this instance) to consume the greater fraction of energy. 2 However, in the ball milling of mixtures it has been postulated that the consumption of energy by one of the constituents is determined by its volume fraction within the mill. 3 Possibly this hypothesis may be a simplification of the ball milling of mixtures since the protective action suggested by Arbiter and Bhrany may result in some preferential energy consumption by one of the constituents of a mixture. The objective of this study has been to determine preferential energy consumption in laboratory ball and rod mills by analyzing size distributions of each material in the products obtained from grinding 1:l mixtures of quartz and limestone. MATERIALS AND METHOD The procedure for carrying out the tests on wet grinding quartz-limestone mixtures has already been described.&apos;r3 In the present investigation, 1:l mix-

Jan 1, 1963

By Robert M. Funk, James E. Lawver

The development of a laboratory and pilot-scale high-tension electrostatic flowsheet for the production of iron-ore super concentrates having silica contents in the range of 0.1% is presented, A variety of hematite and magnetite ores were tested with this flowsheet, and the pertinent metallurgical data are given. The applications and limitations of this process are brought out in terms of both practical and theoretical considerations. There have been many new developments in the past few years that have required mineral beneficiation engineers to consider new techniques for iron-ore concentration. Developments in iron powder metallurgy, and particularly the making of sheet metal directly from high-purity iron-ore concentrates, and the concept of using metallized pellets as a substitute for scrap in electric-furnace steelmaking have created demands for what is commonly referred to as iron-ore superconcen-trates. In most cases, specifications for superconcentrates are that they contain less than 0.1% total gangue, with some applications requiring less than 0.05% gangue. To produce these concentrates, new and modified processes are being developed, and the three methods receiving attention as the primary concentrating methods are: 1) Magnetic separation in which dry rotor-type equipment is used for magnetite and the high-intensity magnets are used for hematite. 2) Amine flotation. 3) "High-tension" electrostatic separation (or, elec-trodynamic concentration). This paper examines the high-tension electrostatic process in terms of its limitations and abilities for the production of iron-ore superconcentrates. A technically effective and simple flowsheet was developed through laboratory and 5 and 100-ton pilot-plant studies for the production of concentrates containing from 0.02 to 0.20% SiO, with iron recoveries between 85 and 90%. The process is also shown to be economically feasible. Laboratory Test Program Separation Characteristics: The suitability of the electrostatic high-tension method for iron-ore supercon-centration stems from the fundamental mechanism governing the process, i.e., particles are separated on the basis of differences in electrical conductivities. This conductivity is a characteristic property of minerals, and if the difference between the conductivities of two min- erals is great enough, then their separation can be performed by a high-tension machine. As shown in Figs. 1 and 2, the critical factor is the time necessary for the particle charge density, which is established by a corona discharge field, to decay to a level such that the centrifugal force acting on the particle exceeds its electrostatic, or image, force. At this point, the particle can leave the rotor at some trajectory and fall into an appropriate product receptacle. This decay time is directly proportional to electrical conductivity, and the process variables, such as feed rate, rotor speed, electrode configuration, and rotor composition, are selected to optimize the ability of the separator to resolve different conductivities. Table 1 lists the measured conductivities for some of the iron and gangue minerals used in developing the flowsheet. These results were obtained by using the conductivity cell described by Lawver and Wright.&apos; The discharge curve of most minerals that lend themselves to super concentration by high-tension is so fast that the

Jan 1, 1971

By E. B. Johnson

Cleveland-Cliffs lron Co., which operates Marquette lron Mining Co.&apos;s Republic mine, conducted a test whereby 35,000 tons of self-fluxed pellets were produced in the grate-kiln system from specular hematite flotation concentrates. A brief description of the pelletizing plant is presented along with pertinent operating details. Date is included which compare operating conditions and the chemical and physical properties of the green and fired pellets for the self-fluxing pelletizing test with the normal acid pelletizing operation. The success of self-fluxed sinter in enhancing the operation of the blast furnace during the past few years has reasonably led to the assumption that the use of self-fluxed pellets might result in even greater furnace efficiencies. A great share of development work in agglomeration has been directed towards techniques related to the production of self-fluxed pellets, but only a limited tonnage of self-fluxed pellets had been produced on a commercial scale until this past year when The Cleveland-Cliffs Iron Co. produced 35,000 tons of such pellets by the grate kiln system at the Republic mine during the period May 21-June 5, 1962. REPUBLIC&apos;S GRATE-KILN PLANT The grate-kiln pelletizing process consists of four stages, namely: feed or balling circuit, traveling grate, rotary kiln and annular cooler (Fig. 1). The balling section is conventional and utilizes four 9x30-ft balling drums in closed circuit with 5x14-ft vibrating screens having 3/8-in. rod decks. The traveling grate is 12 ft wide by 126 ft long and has 14 windboxes — six in the drying section and eight in the preheat section. The rotary kiln is 15 ft ID shell and 114 ft long. The annular cooler is 40 ft in diameter and has 12 windboxes. The cooler is divided into two zones by a moveable curtain wall. The high temperature air from the first zone is used as secondary combustion air in the kiln. Normally the only heat supplied is through the burning of No. 6 oil in the single kiln burner. Hot gases pass counter to the pellet flow through the system. The exit gases from the kiln pass down draft through the preheat section through cyclones and are drawn through the drying bed prior to exiting via the stack. The temperatures are normally held within the following ranges: Kiln 2400-2445 °F Preheat 1850-1950°F Drying 480-520°F Exit gas 200°F Pellets 120°F The design capacity of the Republic mine grate-kiln system was 2500 Itpd. Sustained production in excess of 35% over design capacity has been achieved. No screening of the cooler product is practiced. PELLETIZING TEST CONDITIONS When a decision was made to proceed with a test at the Republic mine pelletizing plant to produce 35,000 tons of self-fluxed pellets, several potential failure factors had to be carefully considered. Research work on a batch and pilot plant scale indicated that the grate-kiln system at Republic would require some major changes in order to obtain optimum conditions. In many cases compromises were agreed upon as major equipment changes and revisions were not feasible. The pelletizing conditions which laboratory development tests revealed were required in order to insure successful production of self-fluxed pellets were: 1) Good mixing of limestone and concentrate and proper moisture control; 2) Higher gas flow rates in the preheat section than are normally used; 3) Higher preheat temperatures than normal; 4) Maximum kiln temperature 2350°F. There was just cause for concern about balling problems that might occur. Approximately 10% of dry pulverized limestone was to be added to the specular hematite concentrate just ahead of the Pekay mixers on the belt feeding the balling drum. Large scale

Jan 1, 1963