Search Documents

By Charles Merguerian

In medium- to high-grade metamorphic terrains such as found in New York City(NYC), rock mass texture and mineralogy are important factors in predicting TBM penetration destiny. Integration of data from over two decades of traditional field and tunnel mapping suggest that hard-rock TBM penetration in the NYC area depends upon textural, mineralogic, and structural control. The bedrock of NYC consists of many different lithologic units of varying age, composition, texture, and metamorphic grade including many varieties of intrusive rock. In addition, brittle faults of numerous orientations cut the polydeformed crystalline bedrock, producing zones of highly fractured and disturbed ground and high water inflows. Pre-bid compilation of published bedrock data, drill core analysis by geologists to establish lithologic and mineralogic trends, integrated surface geologic mapping along a proposed alignment, and targeted petrographic and geotechnical investigations to characterize the rock mass conditions together constitute an important prelude to successful subsurface bidding and tunneling. A carefully planned program of as-built geological mapping, structural analysis, fracture class mapping, and monitoring of machine performance data provide important information for adjusting to changed conditions. In complex terrains, a clear understanding of the structural geology of any proposed tunnel line is the simplest and most cost-effective method to mitigate losses encountered during TBM tunneling.

Jan 1, 2005

By D. A. Lindsey

Gravel lithology affects the quality of aggregate because different rock types in gravel have different physical and chemical properties. The lithologic composition of alluvial gravel reflects the composition of its source terrane and the variable effects of weathering and transport on each rock type. This report discusses lithologic controls on aggregate quality in the mountain-front environment of the Colorado Front Range. Lithologic controls on aggregate quality of gravels were evaluated using pebble count data. Gravel lithology along the Front Range shows both temporal and regional variation. The principal variable in gravel lithology is quartz plus quartzite, of which quartzite is commonly more abundant. Large quantities of metaquartzite derived from the mountain front southwest of Boulder, Colo., were dispersed northeastward during deposition of the oldest Front Range gravels. Average quartz plus quartzite is greatest in the oldest gravels. Aggregate quality is probably enhanced by large quantities of quartzite. Abundant volcanic rocks in gravel may enhance aggregate quantity, but such occurrences are local in extent. Abundant sedimentary rocks in gravel, mainly sandstone near the mountain front, may decrease aggregate quality.

Jan 1, 2002

East Otago gold deposits are hosted in Otago Schist that is the metamorphosed equivalent of Permian-Triassic Torlesse terrane greywackes. Relatively undeformed Torlesse sequences in Canterbury have <l m - 50 m bedding, with c. 500 m - l km and c. three kilometre scale units, typically either: 1) thick-bedded, massive, sandstones; 2) thin-bedded sandstone-argillite flysch; or 3) siltstone- or argillite-dominated units. Such lithological layering in Otago was intensely folded, deformed, and overprinted by metamorphic fabrics during Jurassic-Cretaceous regional metamorphism. Although primary sedimentary structures can no longer be recognised, a æghostÆ lithological variation is still present in Otago represented by psammitic (sand-derived), interlayered (sandstone-siltstone derived) and pelitic (siltstone-mudstone derived) schist. Lithological æunitsÆ in the schist are typically either 20 100 m or c.1 - 2 km thick, and are oblique to faults and shears hosting gold mineralisation at Macraes, Barewood, Nenthom, and Oturehua. Lithological variations and folds in lithological units are important in the along-strike distribution of gold in these deposits, and in the development of relatively high-grade pods and shoots at l00 m - 1.5 km scales. Ramps, flats and step-overs (known to be locally important for controlling mineralisation) are commonly located at lithological boundaries, presumably by local refraction of faults or shear zones as they propagated through folded stratigraphy. The various lithologies have also responded differently to deformation, causing variations in permeability that affected the penetration of mineralising fluids. Mapping lithological variations in barren host-rocks, either directly+ by fieldwork or indirectly by aerial geophysics, is a key to understanding and predicting the distribution of gold at mine and deposit scales.

Jan 1, 2001

By P Stone, J. M. Cook, P. R. Simpson, C Mcdermott

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The SW part of the Southern Uplands is a back-arc section of an accretionary thrust system, divided into structural blocks by major NE-SW shear zones and NW-SE faults forming the margins of Permian half-grabens. The highest arsenic levels in stream sediments (over 65 ppm) are associated with those blocks carrying brittle-ductile transition fabrics. Three factors combine to recomend the area as having potential for gold mineralisation: As-rich greywackes as country rock, felsic intrusions and a major shear zone. Selected stream sediments were analysed for gold using lead fire assay with ultra-pure flux and ICP-MS finish. Several localities showed over 15 ppb Au, the three most significant being within the hanging wall of the Orlock Bridge Fault and each having distinct characteristics

Aug 1, 1995

By R. H. Wright

This paper describes the design philosophy and methods employed in constructing the foundation elements for the Little Britain Project in the City of London. The Contract is a design and construct package for the foundations of a 3-storey basement which will be built using "top-down" construction techniques and is to be carried out by Fairclough Piling and Marine on behalf of Wimgrove Nominees. The Project includes 8000 sq.m. of diaphragm wall and barrettes 139 No. large diameter piles ranging from 900mm to 3000mm in diameter and up to 45m deep, and 9 No. cruciform barrettes for the heaviest column loads. Major factors influencing the design of these foundations include differential settlement, heave analysis and a fast track construction approach. Little Britain will provide 43000 sq.m. of space in two linked buildings which will bridge a new road joining London Wall to Newgate Street. The foundation contract is well advanced and the building is due for completion in the Summer of 1990.

Jan 1, 1989

By Barton J. Suchomel

Introduction Despite perennial economic turbulence, Argentina continues to push ahead with efforts to develop its fledgling hardrock mining industry. The country lacks the infrastructure and mining history of neighboring Chile, but contains vast areas of great resource potential. The eastern slope of the Andean Cordillera in west-northwest Argentina is a relatively little-explored region offering geology highly conducive to the occurrence of base and precious metals deposits. Past exploration has concentrated on locating and evaluating porphyry copper-molybdenum (Cu-Mo) type occurrences. Comparatively little attention has been given to precious metals potential. An interesting and important group of base and precious metals prospects in northwestern Argentina occurs within and adjacent to the Upper Miocene Farallon Negro volcanic complex in Catamarca province. The volcanic complex contains numerous base and precious metals vein occurrences, high gold porphyry copper prospects, and possible disseminated gold targets that have attracted relatively minor attention in the past. Various geologic aspects of the region have been reported by several workers (Llambias, 1970, 1972; Caelles et al, 1971; and Sillitoe, 1973). Regional geology The Farallon Negro volcanic complex is located within the Sierras Pampeanas morphostructural province about 200 km (125 miles) east of the main Andean Cordillera (Fig. 1). The Sierras Pampeanas is characterized by north-south-trending basin and range topography that developed during the Miocene and Pliocene. Uplifted blocks are composed mainly of lower Paleozoic metasediments and granitoid plutonic rocks unconformably overlain by Tertiary redbeds and minor carbonates. A consistent landward migration of volcanic and intrusive ac¬tivity occurred in this region of the Andes from the early Mesozoic through the mid-Tertiary. An eastward extension of magmatism during the Miocene and Pliocene resulted in the formation of the Farallon Negro volcanic center. Volcanism at Farallon Negro ini-

Jan 8, 1988

By Iman G. Ghanad

El presente texto describe un nuevo método para el tratamiento de concentrados de cobre con alto contenido de arsénico utilizando el carbón activado como catalizador. Para ello, se realizaron pruebas de lixiviación con concentrados de enargita de tres minas de Chile, Perú y Estados Unidos, donde los resultados señalaron que la disolución de la enargita fue más rápido con la influencia del carbón en la solución lixiviante, incluso después de haber reciclado el carbón.

Sep 12, 2011

By D. W. Agers

This paper is an extension of previous work evaluating a new extractant, LIX®-64, for recovery of copper from dilute acidic solutions. Large scale pilot plant operations have confirmed the technical and economic feasibility of the process and, with minor exceptions, scale up parameters obtained by previous laboratory work. Operating problems encountered in the pilot plants are discussed. Design parameters for-scale-up to commercial plants are presented and discussed along with a revised capital cost estimate. The future pilot program is discussed, including minor design changes and the effect of entrained organic on dump leaching efficiency.

Jan 1, 1967

By F. Lindroos

A cornerstone in the LKAB Green Pellet concept is to produce pellets with a small footprint in terms of energy con-sumption, CO2 emission and emission of other elements harmful to the environment, like dust, sulphur dioxides, nitrogen oxides, chloride and fluorine. The concept also encompasses our determination to make pellet products that contribute to low environmental impact and low energy consumption in our customer?s processes. The presentation will focus on the pelletizing process. It will describe both how we have attempted to decrease the generation of unwanted components in the process gas, and how we have tested or evaluated equipment for external gas cleaning. We will discuss and give examples from recent and on-going efforts and outline some of the future challenges we see, to meet our own environmental standards and also the tough demands imposed by EU and national legislation, while striving to boost production.

May 1, 2011

By Nic Slatalla

Resin anchored rock bolts are an effective tool to control the deformation of an underground opening because they combine high support capacity with fast installation. However, there are still numerous shortcomings concerning the understanding and interaction of the system bolt-resin-rock. Field and laboratory test series have been conducted for evaluating the load capacity and bond strength of resin grouted rock bolts in different host rocks under axial load. This paper describes that the behavior and shear strength of the system bolt-resin-rock depends on the rock type and discusses a simple correlation between peak shear strength and shear stiffness in the ratio 1:1000 which may moreover be helpful for estimating rock bolt capacity after installation.

Jan 1, 2006

In this paper a numerical formulation is presented for determination of the axial load along a cable bolt for a prescribed distribution of rock mass displacement. Results using the program CABLE indicate that during excavation, the load distribution that develops along an untensioned fully grouted cable bolt depends on three main factors: (i) the properties of the cable itself, (ii) the shear force that develops due to bond at the cable-grout interface (i.e. bond stiffness), and (iii) the distribution of rock mass displacement along the cable bolt length. In general, the effect of low modulus rock and mining induced stress decreases in reducing bond strength as determined from short embedment length tests, is reflected in the development of axial loads significantly less than the ultimate tensile capacity even for long cable bolts. However, the load distribution is also dependent on the deformation distribution in the reinforced rock mass. Higher cable bolt loads will be developed for a rock mass that behaves as a discontinuum with deformation concentrated on a few fractures, than for one which behaves as a continuum, either due to a total lack of fractures or a very high fracture density. This result suggests that the stiffness of a fully grouted cable bolt is not simply a characteristic of the bolt and grout used, but also of the deformation behavior of the ground. In other words, the same combination of bolt and grout will be stiffer if the rock behaves as a discontinuum than if it behaves as a continuum. This paper also explains the laboratory test programme used to determine the constitutive behavior of the Garford bulb and Nutcase cables bolts. Details of the test setup as well as the obtained results are summarized and discussed.

Jan 1, 1996

By Jorj O. Osterberg

Until ten years ago, the largest load tests on drilled shafts (bored piles) were about 3,000 tons (27MN). These tests were made with kentledge (large weights, usually concrete blocks) stacked up as a reaction to the applied downward load of a hydraulic jack. In some cases, the jack load is resisted by a load frame held down by piles or anchors connected to the frame. When the test loads exceed 3,000 tons (27MN), these methods become cumbersome expensive and time consuming. The Osterberg (O-cell) test method does not require any reaction load. It has become the only cost effective method for static load testing of high capacity shafts. Over 650 load tests have been performed with this method, 86 of which were over 3,000 tons (27 MN) and 40 over 5,000 tons (44 MN), and the largest test load was 17,000 tons (150 MN). Tests have been made on sands below the water table, shafts ending in rock sockets, and cemented sands and gravels. Test results and details for selected load tests are discussed.

Jan 1, 2002

By David E. Thompson

This paper describes the full-scale field load testing of three deep foundation units using the Osterberg Load Cell. The load tests were completed on three separate projects, two in Massachusetts and one in New York. The Massachusetts projects involved the load testing of two 18-inch O.D. concrete-filled steel pipe piles over water for railroad bridge reconstruction projects in Revere and Saugus/Lynn. The New York project involved the load testing of a 24-inch diameter drilled shaft socketed into sandstone on land for a building foundation in Rochester. The 18-inch O.D. piles were loaded to failure at jack pressures of 142 to 215 tons. The drilled shaft was loaded to failure at jack pressures of approximately 450 tons. The loading testing procedure is described and the results of the three tests are presented. The advantages and disadvantages of the Osterberg load cell for load testing of deep foundations are discussed.

Jan 1, 1989

By Drew Floyd

Five full-scale pile load tests were performed on pairs of PZ-22 sheet piles installed with a vibratory pile driving hammer. The sheet piling was installed in several locations in soil generally consisting of miscellaneous granular fills overlying soft organic silts, inorganic silt interbedded with sands and gravels, very dense glacial till and shale bedrock. The test program also included the use of tip tell tales to determine what capacity could be attributed to tip resistance and skin friction. During the design phase of the project, it was assumed that the capacity of the sheet piles driven with the vibratory hammer could be correlated with the rate of penetration. The correlation between vertical capacity and rate of penetration would be used as a basis for determination of a driving criteria from driving the production sheet piling. The sheet piling load tests demonstrated that it was not possible to correlate the capacity of sheet piling driven with a vibratory hammer and the rate of penetration. It was also demonstrated that the capacity of the sheet piles was directly related to the density of the soil at or just below the tip. The results also tend to agree with empirical equations provided by Meyerhof (1976).

Jan 1, 1989

By Rolf Katzenbach

Construction of drilled shaft foundations with the use of hydraulic oscillators and rotators to install temporary casing over the full depth of the shaft is described. The equipment and techniques were developed in the 1960?s in Germany and full-depth casing is now the predominant method of construction in Europe. Its use in North America is increasing. This paper presents an overview of full-depth casing methods and a summary of available load test data evaluated by the authors to compare the load transfer and capacity performance of shafts installed by various construction methods. Results demonstrate that load transfer and capacity of full-depth casing shafts are equal to or exceed that of shafts constructed by dry or slurry methods and that measured capacities are consistent with generally accepted design equations. The principal advantage of full-depth casing methods over other installation techniques is that the risk of defects in the shaft is minimized. Casing is able to penetrate into the ground under any geologic or groundwater condition when this technique is applied. Potential delays and cost overruns can thus be avoided and a safe, economical foundation element is created.

Jan 1, 2007

By Mark K. Larson

Calibration of LaModel for deep coal mines begins with adjustment of overburden stiffness for load transfer distance. This calibration determines whether mining induced stresses are concentrated in the immediate abutment of the gob, or spread over a wider area. In the absence of site information, an empirically-based estimate is often used. Where data is available, a recommended calibration procedure can be followed, as is done in this case study at a deep western longwall mine, with minor modifications and extensions. In this case, data sources included borehole pressure cells, flatjacks installed in series with support Cans, and observed changes in ground conditions. Calibration was based on the first detection of mining-induced stress from the advancing longwall. Detection was found to depend on the type and sensitivity of measurement. Borehole pressure cell data with a 20-psi-increase detection threshold were chosen as the standard, in accord with data used in deriving empirical relationships. Application of this standard produced a load transfer distance estimate roughly four times the empirical relationship developed by Peng and Chiang (1984). This is a significant deviation with important implications for panel design at this site. Data from flatjacks, ground condition observations, and borehole pressure cells with higher threshold values, were tightly clustered and show load transfer distances from two to four times empirical guidance. Ratios between various measurements can be used to adjust measurements to the standard (although they may depend on mine geology). Once established, ratios can be used to adjust estimates, say from support flatjacks or ground observations, to the standard, where borehole pressure cell data is not available.`

Jan 1, 2012

By M. M. D. S. Vemba

Paper written on project work carried out in partial fulfilment of B.Sc. Eng (Mining Engineering) degree Engineering refers to the application of mathematics and other sciences to logically develop solutions to problems. However, in opencast mining, due to the randomness of operations, the use of mathematics is often neglected. Instead, practices that have proven successful elsewhere tend to apply. At the other end of the scale, mathematical models have been developed to identify and quantify all the operational parameters involved in the loading and haulage of ore. These are then used to optimize the operation. Optimization in this context, refers to the reduction of cost through effective utilization of the available time and resources. Considering these mathematical models, the loading and transport system at SMC (Catoca Mining Society) will be assessed with a view to its optimization. The discussion will be introduced by considering the mine background and other general information, which will highlight the main operational variables.

Jan 1, 2004

By Emil Szaks

[A great number of papers have been presented at various Engineering Society meetings on the Unit Train subject. Moat are descriptions of facilities that have been constructed or are abort to be built. Many describe the facility as being the World's fastest, newest, largest, incorporating the latest technology and so forth, Many are duplications of installations that have been recently constructed, sort of carbon copies but perhaps arranged differently. The trend has been to incorporate loop tracks, rotary dumpers, indexers and, of course, the snivel coupler equipped unit train. How that the energy crisis has increased the use of coal, there has been a tremendous Increase in applications for permits to construct rail to river coal loading facilities. This paper is different. It does not describe any single existing facility, but is given to alert prospective terminal owners and engineers that there are items that require considerable study and evaluation beside merely selecting an indexer, car dumper, stacker, ship or berg loader and so on. An important item is the selection of the railway car which in turn can affect the selection of the method of loading and unloading. Let us list a few of the items that should be considered and discuss the areas that require examination:]

Jan 1, 1979

By A. M. Esteves

This paper offers an overview of local content policies and practice in the mining sector. Specifically, the paper aims to answer the question of how national and regional governments, industry and civil society can work together to seek an optimal outcome while pursuing their diverse objectives. The paper begins by defining local content and its scope at the subnational level. Specific recommendations for the design of local content policies to mitigate social, economic and governance risks are developed. The document then offers some recommendations regarding the role of partners in design, implementation, monitoring, and enforcement of local content policies.

Aug 1, 2013

By A. Atta-Quayson

Since 2012, Ghana has been implementing local procurement regulations in the mining sector to broaden and deepen linkages between mining and other sectors of the economy. The regulations have been implemented in collaboration with the mining industry. This paper offers an in-depth analysis of how the local procurement regulations and related initiatives have been implemented so far. Primary data gathered with semi-structured interviews and secondary sources of data indicate a steady improvement in both in-country procurement and local manufacturing of inputs for the mining industry. There are, however, some challenges relating to tariff structure and support (financial and technical) for local suppliers and manufacturers to meet high standards and demands of the mining industry. This calls for a well-thought-out strategy and programme of activities to sustain and improve on progress made.

Feb 2, 2022