Search Documents

By Joe Pezo

Desde 1999 se desarrollaron pruebas de lixiviación de concentrados en la planta LESDE de Toquepala con el propósito de evaluar las recuperaciones y los tiempos de procesamiento. Las recuperaciones a nivel laboratorio indican que la promoción de la actividad bacteriana es uno de los factores para acelerar el proceso de solubilización del cobre calcopiritico del concentrado. La actividad bacteriana se define como la capacidad de adaptación que tienen las bacterias en medios lixiviantes para elevar la velocidad de oxidación del ión ferroso y convertirlo en férrico y es el mecanismo para la lixiviación del sulfuro primario o calcopirita, el resultado de la interacción de las bacterias ferrooxidantes, el oxígeno y el control de ácido que mantienen un pH por debajo de 2.1. En ese sentido, el presente texto señala las pruebas de lixiviación de concentrados que incluyen estos últimos conceptos, con el objetivo de evaluar la factibilidad técnica y económica de obtener licores de cobre que puedan ser aprovechados utilizando la capacidad existente de extracción por solventes y electrodepositación de la planta LESDE Toquepala.

Sep 12, 2005

By C. Thiart

Kriging is an interpolation technique for predicting unobserved responses at target locations from observed responses at specified locations. Kriging predictors are best linear unbiased predictors (BLUPs) and the precision of the BLUP is assessed by the mean square prediction error (MSPE), commonly known as the kriging variance. Both the BLUP and the MSPE depend on the covariance function describing the spatial correlation between locations and on specific parameters. The parameters are usually treated as known, whereas in practice they invariably have to be estimated and the empirical BLUP (that is, the EBLUP) so obtained. The empirical or estimated mean square prediction error (EMSPE), or the so called ?plug-in? kriging variance estimator, underestimates the true kriging variance of the EBLUP, at least in general. In this paper five estimators for the kriging variance of the EBLUP are considered and compared by means of a simulation study in which a Gaussian distribution for the responses, an exponential structure for the covariance function, and three levels of spatial correlation ? weak, moderate, and strong ? are adopted. The Prasad-Rao estimator obtained using restricted or residual maximum likelihood (REML) is recommended for moderate and strong spatial correlation and the Kacker-Harville estimator for weak correlation in the random fields.

Jan 1, 2014

By Ihsan Berk Tulu

In the Analysis of Retreat Mining Pillar Stability (ARMPS) program, the magnitude of the abutment loading adjacent to a gob area is calculated using an ?abutment angle? concept. The extent of the abutment loading is determined solely as a function of depth from an empirically derived equation. In the recommended calibration method for LaModel, it was believed that the empirical equations for calculating the magnitude and extent of the abutment load, as used in ARMPS, were the best available methods for determining these critical overburden loading values. Therefore, similar calculations were implemented in the LaModel calibration method. However, the latest in situ stress measurements of abutment loading performed in the United States and Australia have shown that there can be significant deviations in the measured abutment magnitude and extent as compared to the predicted values from the empirical formulas used in ARMPS and LaModel. It seems reasonable that the overburden geology, depth, extraction panel width, and mining height should have a significant effect on the extent and magnitude of the abutment load. However, the current empirical formulas do not incorporate many of these significant parameters into determining the abutment load on the pillars. In this paper, stress measurements from US and Australian mines were back-analyzed by using analytical and numerical methods to investigate the measured abutment extent and loading. Ultimately, it was determined that the original empirical abutment extent formula in conjunction with the original ALPS square-decay stress distribution function was supported by the case histories in this paper. Also, for depths less than 900 ft, the average 21° abutment angle was supported by the case histories; however, at depths greater than 900 ft, the abutment angle was found to be significantly less than 21° and should be calculated with a new proposed equation.

Jan 1, 2012

Current mine production planning, scheduling, and allocation of resources are based on mathematical programming models. In practice, the optimized solution cannot be attained without examining all possible combinations and permutations of the extraction sequence. Operations research methods have limited applications in large-scale surface mining operations because the number of variables becomes too large. The primary objective of this study is to develop and implement a hybrid simulation framework for the open pit scheduling problem. The paper investigates the dynamics of open pit geometry and the subsequent material movement as a continuous system described by time-dependent differential equations. The continuous open pit simulator (COPS) implemented in MATLAB, based on modified elliptical frustum is used to model the evolution of open pit geometry in time and space. Discrete open pit simulator (DOPS) mimics the periodic expansion of the open pit layouts. Function approximation of the discrete simulated push-backs provides the means to convert the set of partial differential equations (PDEs), capturing the dynamics of open pit layouts, to a system of ordinary differential equations (ODEs). Numerical integration with the Runge-Kutta scheme yields the trajectory of the pit geometry over time with the respective volume of materials and the net present value (NPV) of the mining operation. A case study of an iron ore mine with 114 000 blocks was carried out to verify and validate the model. The optimized pit limit was designed using Lerchs-Grossman?s algorithm. The best-case annual schedule, generated by the shells node in Whittle Four-X yielded an NPV of $449 million over a 21-year mine life at a discount rate of 10% per annum. DOPS best scenario out of 2 500 simulation iterations resulted in an NPV of $443 million and COPS yielded an NPV of $440 million over the same time span. The hybrid simulation model is the basis for future research using reinforcement learning based on goal-directed intelligent agents.

Jan 1, 2008

Accurately estimating load distributions and ground responses around underground openings play a significant role in the safety of the operations in underground mines. Adequately designing pillars and other support measures relies highly on the accurate assessment of the loads that will be carried by them, as well as the load-bearing capacities of the supports. There are various methods that can be used to approximate mining-induced loads in stratified rock masses to be used in pillar design. The empirical methods are based on equations derived from large databases of various case studies. They are implemented in government-approved design tools and are widely used. There are also analytical and numerical techniques used for more detailed analysis of the induced loads. In this study, two different longwall mines with different panel width-to-depth ratios are analyzed using different methods. The empirical method used in the analysis is the square decay stress function that uses the abutment angle concept, implemented in pillar design software developed by the National Institute for Occupational Safety and Health (NIOSH). The first numerical method used in the analysis is a displacement-discontinuity (DD) variation of the boundaryelement method, LaModel, which utilizes the laminated overburden model (Heasley, 1998).

Jan 7, 2020

By P. J. Mehrfert

"Recovery of mineralized coarse particles is notoriously low in conventional concentrators that treat copper porphyry ores. The application of coarse particle flotation techniques has the potential to achieve comparable metallurgical performance at significantly coarser primary grind sizings. ALS Metallurgy has been conducting both internal research and commercial test programs to investigate the potential of Eriez HydroFloatTM technology on copper sulphide ores. Test data indicates that significant improvements in the recovery of copper sulphide bearing particles between 200µm to 850µm can be achieved using Hydrofloat technology compared to conventional flotation techniques. This paper summarizes the results from a selection of test programs that includes recovery by size data from both conventional flotation and HydroFloatTM tests. An explanation of the apparatus and test procedure will be given. Mineralogical analyses of the test products and characteristics that limit metallurgical performance will be discussed.Description of Apparatus and Test ProtocolThe HydroFloatTM laboratory cell is a clear plastic column with an internal diameter of 14 cm. Water and air are introduced to the cell through a circular manifold located in the lower portion of the cell. The cell has a conical bottom which directs slurry to a pinch valve that controls the discharge of tailings. Feed solids are introduced to the upper portion of the cell in slurry form. The cell is operated in a manner such that the manifold water creates a teeter bed zone of suspended solids in the middle portion of the cell. Tailings exit the bottom of the cell at a high pulp density, and most of the introduced water overflows the top of the column and is collected in a launder. Particles with a hydrophobic surface may attach to air bubbles that percolate through the teeter bed, rendering them sufficiently buoyant to be transported to the overflow launder.Three significant features of this arrangement enhance the potential to recover coarse, low grade particles by flotation techniques. Firstly, the hindered settling conditions created by the rising column of water allow coarse particles to become buoyant once attached to a modest sized air bubble. Secondly, the flow conditions within the cell are relatively quiescent compared to a conventional flotation cell that utilizes an agitator. This allows particles that have limited hydrophobic portions of their surface, due to a low content of exposed sulphide mineral, to maintain a somewhat fragile attachment to air bubbles long enough for successful recovery to the overflow. Finally, the absence of a froth phase at the top of the cell allows particles attached to air bubbles to immediately exit the vessel, reducing the potential to drop back into the pulp phase as bubbles burst or coalesce."

Jan 1, 2017

It cannot be said that accurate and reliable ore reserve estimation is the fundamental of any mining operation success. Estimation techniques which are used to estimate the grade distribution of an orebody together with the assessment of uncertainty and risk have a vital influence on the success of any optimisation algorithm. Traditional estimation techniques such as kriging or inverse distance weighting are frequently used for assigning grade values to blocks. Various attempts have been made in order to compare geostatistical estimated methods for ore reserve estimation. This paper aims to evaluate the sensitivity of different estimation methods over changing the block dimension. For this reason, several block models with different dimensions were derived in Chador Malu iron ore mine which is located in 180 km northeast of Yazd in the centre of Iran. Each block model was estimated by different estimation methods such as nearest neighbours (NN), inverse distance (ID) and ordinary kriging (OK). The results of each estimation methods were compared against a control block file created by using the assay results of all blastholes drilled in the ore over four benches of the pit. The results signify that by estimating the large block size, no significant improvement occurred due to the employment of different estimation techniques. Furthermore, the grades estimated based on ID method is more reliable, but OK methods estimated more accurate tonnage.

Dec 6, 2010

By Manoj Khandelwal, Minghui Liu, Jian Zhou, Kun Du

The waste rock and tailings backfill into the mined-out areas are the most effective method for solving the environmental pollution and surface disasters for nonferrous metals mines. In practice, the success and availability of backfill operations are dependent on the slurry fluidity and the strength properties of cement backfill. The transport of the slurry through the pipeline to the designated backfilling area relies on its eximious flow properties, while the appropriate strength of the filling body ensures the safe operation of the stope. In this paper, the effects of cement and aggregate types on the slurry fluidity and strength characteristics of cemented backfill are studied in detail, which are often ignored in other pieces of literature. Diffusivity is used as an indicator to evaluate the slurry fluidity. Various slurries whose concentrations ranging from 70%, 73%, 75%, 78%, and 80% are made with different aggregate ratios and cement-sand ratios are tested. It has been shown that slurry fluidity is inversely related to its concentration, but 78% is the “stopping point” for the deterioration of fluidity. The addition of rod-milled sand improves or worsens the cemented backfill (CB) strength depending on the amount of rob-milled sand. The uniaxial compression experiment results on 216 CB specimens produced by different combinations of influencing variables showed that CB specimens made from cement with superior mechanical properties have a higher uniaxial compressive strength (σucs). It has been also found that the effect of aggregate ratio on the CB strength is not singular, but works in conjunction with the curing time and the cement-sand ratio. The longer the curing time and the higher the cement content, the higher the CB’s σucs. To avoid the time-consuming and costly problem of obtaining the strength of the CB from indoor experiments, an SVR model capable of predicting the uniaxial compression strength of CB specimens is proposed, which is optimized by genetic algorithm (GA) and particle swarm optimization (PSO) algorithm. The results of the three performance indexes (MAPE, MSE, and R2) show the superior performance of the GA-SVR and PSO-SVR models and the agreement of the predicted results with the experimental results, which indicate that these two models can accurately predict the σucs of CB.

Feb 3, 2022

By Peter Radziszewski

"Comminition process costs, which typically represent an important contribution to mining operating costs, can themselves be divided roughly between energy and liner /charge wear. As such, developing the ability of predicting mill wear will allow a more accurate estimation of wear costs and therefore their control. In this paper and based on the possibility of estimating energy dissipated in impact and abrasion by using a discrete element charge motion model for mill charge motion simulation, media wear will be investigated principally as a function of three wear mechanisms : impact, abrasion and corrosion. Experimental results will be used to identify a total media wear model. Model results will be compared with real mill data from three operating Australian mines. These preliminary results show for the cases tested that the overall average error, as compared with the observed cases, is 0 % with a standard deviation of 66.1 %. Results from the Bond abrasion index tests, for the same cases investigated, give an overall error of 73 % and a standard deviation of 192.5 %. Further work is in progress to improve test procedure, validity and confidence.INTRODUCTIONComminition process costs, which typically represent an important contribution to mining operating costs, can themselves be divided roughly between energy and line / charge wear. In Greenfield situations where the estimation of operating costs is critical in determining project feasibility, the level of confidence in such estimates becomes quite important. With regards to media wear, the Bond abrasion test currently serves as the standard media wear prediction device. However, as shown [l, 21 test results once compared with actual wear rates can vary greatly. Figure 1 shows test results as compared with 15 cases. Average error over this data is 73 % with a standard deviation of 192.5 %. As such, developing the ability of more accurately predicting mill wear will allow greater confidence in wear cost estimation and therefore their control."

Jan 1, 2001

By Robert A. Cummings, Madan M. Singh

In April 1984 a subsidence depression formed directly beneath a two-story frame residence, near Linton, IN, causing 2 ft of separation between the floor and walls, and damaging both the foundation and interior of the building. The Office of Surface Mining undertook the rehabilitation of the area under its emergency response program. This paper describes the investigation performed to determine the cause, severity, and extent of the problem. Abandoned mine workings were found approximately 55 to 60 ft below the house. Based on the findings, remedial measures were prescribed. An abatement program consisting of grouting the mine voids was recommended, and specifications prepared. These were implemented, and the area has been successfully stabilized.

Jan 1, 1986

By Douglas E. Pollock

Recent NIOSH published information has shown an increase of rapidly progressive coal workers? pneumoconiosis (CWP) in the southern Appalachian coal region (SAR) of the U.S., despite the fact that compliance data indicates that most coal miners have been exposed to coal mine dust concentrations below the statutory limit of 2 mg/m³. While the exact cause of these elevated CWP levels in the SAR has not been established, several factors may be contributing to the increase in occupational lung disease among coal miners. The mining of high rank coal is known to lead to higher CWP rates, and this type of coal is mined in a portion of this region. Also, a high percentage of the mines in the region are on reduced dust standards because of the high silica content of the airborne dust resulting in miners possibly being exposed to excessive amounts of respirable silica dust. Exposure to excessive amounts of respirable silica dust can lead to silicosis, a disabling and potentially fatal lung disease. NIOSH?s Respiratory Hazards Control Branch has been investigating the possible causes that would account for the observed higher trends in disease progression through literature review, data analysis and in-mine surveying. The investigation to date has revealed that underground mines are faced with cutting large amounts of rock in order to maintain haulage clearances. Cutting rock not only increases the potential for silica exposure, it increases the requirement for machine maintenance, which was a concern observed during dust surveys conducted by NIOSH. Over half of the mines operating in the SAR are on reduced standards due to high silica content. Adequate face ventilation of the continuous miner and roof bolter and limited down-wind operations from the miner are also issues of concern and items that require the constant attention of miners operating in these conditions.

Jan 2, 2010

By D. E. Pollock

Recent NIOSH published information has shown an increase of rapidly progressive coal workers? pneumoconiosis (CWP) in the southern Appalachian coal region (SAR) of the U.S., despite the fact that compliance data indicates that most coal miners have been exposed to coal mine dust concentrations below the statutory limit of 2.0 mg/m³. While the exact cause of these elevated CWP levels in the SAR has not been established, several factors may be contributing to the increase in occupational lung disease among coal miners. The mining of high rank coal is known to lead to higher CWP rates, and this type of coal is mined in a portion of this region. Also, a high percentage of the mines in the region are on reduced dust standards because of the high silica content of the airborne dust resulting in miners possibly being exposed to excessive amounts of respirable silica dust. Exposure to excessive amounts of respirable silica dust can lead to silicosis, a disabling and potentially fatal lung disease. NIOSH's Respiratory Hazards Control Branch has been investigating the possible causes that would account for the observed higher trends in disease progression through literature review, data analysis, and in-mine surveying. The investigation to date has revealed that underground mines are faced with cutting large amounts of rock in order to maintain haulage clearances. Cutting rock not only increases the potential for silica exposure, it increases the requirement for machine maintenance which was a concern observed during dust surveys conducted by NIOSH. Over half of the mines operating in the SAR are on reduced standards due to high silica content. Adequate face ventilation of the continuous miner and roof bolter and limited down-wind operations from the miner are also issues of concern and items which require the constant attention of miners operating in these conditions. Disclaimer: Mention of any company or product does not constitute endorsement by the National Institute for Occupational Safety and Health.

Jan 1, 2009

The influence of varying amounts of magnesia, silica, and alumina in iron ore sinter on its mineralogy, reducibility index (RI), reduction disintegration index (RDI), physical breakdown (AI and TI), and production properties (coke breeze rate) were examined. It was found that the mineralogy of iron sinter can more easily be predicted from its chemical composition than from the RI, RDI, AI or TI. Anticipating the consequence that varying amounts of MgO and SiO2would have on sinter properties is complex, and not necessarily predictable. High concentrations of Al2O3in the sinter result in high concentrations of the SFCA phase, but with drastically deteriorated properties. This study also confirmed that the form in which fluxes are added to the raw material sinter mixture affects the mineralogy and properties of the produced sinter.

Jan 1, 2010

By T. Holmes, D. C. Russell, G. Jolly

"The AMEC Oakville office is involved in the design and construction of an iron ore concentrator located in Liberia. Currently, the site ships Direct Shipped Ore (DSO) to overseas customers. The DSO mine-site and port can experience heavy annual rainfalls. The IMSBC Code requires that cargoes are only accepted for loading when the moisture content of the cargo is less than its Transportable Moisture Limit (TML). The moisture content of the DSO has, on occasions, risen to near or above its TML. AMEC was asked to advise whether the concentrate produced from the new concentrator would or would not have the same problems with moisture content and ship loading as the DSO.INTRODUCTION Liberia was, at one time, the world’s sixth largest exporter of iron ore and used some of the most modern mining operations of their time. However, the country has not produced iron ore over the past seventeen years because of civil unrest. The return of stability to the country has allowed the redevelopment of the iron ore industry. ArcelorMittal Liberia (AML) obtained a concession for mining in the Nimba County area of Liberia (Figure 1) in December, 2004 and has studied the known iron ore deposits and former mining operations in this area. It began phase 1 operations in June 2011 with the direct shipping of high grade ore at a rate of up to 4Mtpa. The processing of the lower grade ore in phase 2 of the project requires additional processing capability to produce at the design rate of 15Mtpa. DSO and Concentrate The DSO in the first phase is selectively mined at an average grade of 60% Fe, and then crushed and screened to -10 mm with no washing or concentration. Testing of samples has indicated a size distribution that is finer than typical sinter feed material, although critical material below 0.10 mm is low in most cases, and overall the ore is coarser than typical concentrates or ultrafine products (Feasibility study report, 2011). The phase 1 DSO facility will cease operation after the phase 2 concentrator comes into operation."

Jan 1, 2014

By Charles Deacon

The mining industry is constantly taking greater cognisance of their operating costs as a strategy to counter the effects of falling commodity prices. As a result, optimal operating efficiency is more important than ever. One such operation is that of blasting. Considering the relative increasing costs of explosives and accessories it is desirable to optimise the number of blast-holes fired by maximising their individual output. This achievement may now only be possible following the advent of higher technologies in the form of modified explosives and electronic detonators. This paper reviews and introduces some techniques of blast monitoring, types of operations where each is most suited, resulting modifications to blast designs, and identifies some pitfalls to watch out for when analysing the results.

Jan 1, 2000

By O. Dojcar

The results of a laboratory investigation of rock fragmentation conducted with a model material were partially verified under field conditions. The object of the investigation was to study the qualitative and quantitative relations between the parameters of the primary blast and fragmentation to enable the planning of an economically efficient degree of disintegration with optimum utilisation of the blast energy. The three blast parameters that were considered were burden, specific charge and the ratio of spacing to burden

Jan 1, 1991

By N. Coli

The exhausted Santa Barbara open pit mine (Tuscany, Italy), owned by the main electric power company in Italy (ENEL S.p.A,) extracted lignite as a fuel for the Santa Barbara thermoelectric power plant. The mining activity led to the excavation of a wide slope (with maximum height of 200 m and a planar extension of about 1300 m x 500 m) in the Shale Limestone Chaotic Complex (SLCC) (Figure 1). Since the beginning of its excavation the slope underwent rotational landslides and diffuse instability phenomena. From a geotechnical point of view the SLCC represents a typical bimrock (block-in-matrix rock) (Medley 1994, Medley 2002, Medley 2007) characterized by a mixture of a highly sheared, scaly-fabric, clayey matrix and calcareous blocks ranging from a few millimetres to tens of metres in size. Since the geometrical properties of blocks (grain-size distribution, shape, orientation and volumetric proportion) have been proved to influence the mechanical behaviour of bimrocks (Lindquist & Goodman 1994, Goodman & Ahlgren 2000, Kim et al. 2004, Sonmez et al. 2006), the aim of the present study is to investigate the geometrical properties of calcareous blocks in order to properly characterize the mechanical behaviour of the SLCC bimrock and to further assess the stability of the slope. Block size-distribution and shape were investigated by means of advanced image analysis techniques of SLCC pictures taken in the field. Geostatistical semivariograms and variographic maps were also used in order to investigate the anisotropy of block spatial distribution. Finally, in-situ large sized sieving tests were carried out to investigate the volumetric block proportion within the clayey matrix.

May 1, 2009

By İbrahim Çınar, Hakan Özşen

Mine workers in heavy and dangerous work are under several physical risk factors, for example temperature, humidity, noise, vibration, lighting and air velocity. Thermal comfort includes parameters such as air temperature, air humidity, air flow rate, radiant heat, metabolic rate and garment insulation. In this study, thermal comfort conditions were evaluated using thermal comfort indices defined as predicted mean vote (PMV) and predicted percentage dissatisfied (PPD) which were determined by measurements taken from an underground coal mine for approximately 100 days. Although the metabolic rate (light work) was kept at 2 met, it was found that predicted mean vote ranged between − 2.58 and 1.68. The predicted percentage dissatisfied index was found to reach 95%. According to the results, it can be seen that thermal comfort may have negative effects on occupational health and safety. The change in thermal comfort index values in the Soma Underground Coal Mine was investigated in detail and the reasons for the changes were determined. Furthermore, determining the optimal working environment for the mine workers was also an aim of this study.

By Wendy M. Brunner

A 70% excess of mesothelioma, an asbestos-related cancer, has been reported among men in northeastern Minnesota, where iron mining has been the major industry. The Minnesota Department of Health has studied iron miners who developed mesothelioma to identify possible sources of asbestos exposure. A database of all Minnesota residents diagnosed with mesothelioma between 1988 and 1996 was linked to a database of approximately 72,000 current and former Minnesota iron-mining employees to identify cases who had ever worked in the mining industry. The job histories of the cases were examined to determine if any of their jobs could have involved exposure to commercial asbestos. Seventeen individuals diagnosed with mesothelioma in Minnesota between 1988 and 1996 were found to have worked in the iron mining industry. Of the 15 for whom adequate work histories were available, 14 had identifiable sources of exposure to commercial asbestos in jobs held both inside and outside of the mining industry. The time between employment in these asbestosexposed occupations and the diagnosis of mesothelioma is consistent with the 20 or more year latency period that has been observed in other studies of this cancer. © 2007 Elsevier Inc. All rights reserved. Keywords: Mesothelioma; Asbestos; Iron miners; Taconite; Epidemiology; Case series

Jan 1, 2007

By David Oyler, Craig Compton

The The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL) is continuing to investigate the behavior of fully grouted roof bolts in the weak roof rock of the Safety Research Coal Mine (SRCM). This paper describes the results of three studies: • A series of 24 pull tests of bolts installed fully grouted and overcored to leave 12 inches of grouted bolt. The tests compared the pull-out performance of offset-head roof bolts with that of standard 5/8-inch bolts; • A second series of 24 tests that compared the pull-out loads obtained by bolts installed with 1 ft of resin (a Short Encapsulation Pull Test or SEPT) to that of fully grouted bolts overcored to leave only 12 inches of grouted bolt, and; • An investigation into the pressures generated during the installation of fully grouted resin bolts. All of the bolts installed and pulled were overcored and removed from the roof after the pull tests to allow inspection of the resin. The first study found that there was no significant difference in pullout load between the offset-head bolts and the standard bolts. The second study, comparing the SEPT bolts and the partially-overcored fully grouted bolts, indicated that SEPT can significantly underestimate bolt anchorage grip factor, suggesting that the SEPT is a conservative measure of actual bolt performance. Significant loss of resin to cracks in the roof was observed in the bolts overcored in the SRCM. The third study explored one possible explanation for the resin loss, high pressures generated during bolt installation. These tests employed bolts installed in strain gauged steel tubes. The results confirmed that significant pressures (greater than 4,000 psi) can be generated during bolt installation. The results of the pressure tests, combined with the observations of resin loss in bolts installed in the SRCM, suggest that under some circumstances resin loss and under-encapsulation could take place and lead to degraded bolt performance. Glove fingering was observed in all recovered bolts to various degrees. The limited comparative data suggested that the effect of glove fingering ranged from slight to moderate. Complete mixing of the resin was observed on all of the 40 bolts recovered (28 fully grouted and 12 SEPT). Australian and U.S. resins were compared and the Australian resins were observed to have much smaller catalyst compartment areas and lower resin viscosities. These differences are suggested as potential explanations for occasional resin mixing problems noted in Australian resin bolt installations.