Search Documents

By Christopher Mark

Colombia is 11th largest coal producing nation in the world, and the world?s fifth largest coal exporter. But while most of Colombia?s coal is mined at large modern surface mines located near the Caribbean coast, there are also underground mines that produce high-grade metallurgical coal. These mines employ traditional hand-loading techniques in a variety of geologic environments, and they have some of the highest accident rates of any Colombian industry. The National Institute for Occupational Safety and Health (NIOSH) has been collaborating with POSITIVA, the primary provider of worker?s compensation insurance to the Colombian underground coal industry, to reduce the economic and social cost of rock falls in these mines. The specific goals of the collaboration are to 1) document practices and conditions in Colombian underground coal mines, 2) identify relevant international best practices, and 3) provide recommendations for developing a national campaign to reduce fatalities and injuries associated with roof falls. NIOSH conducted a survey of seven underground coal mines in four separate coalfields. Five of the mines were characterized by steep dips and weak roof and floor rock. The coal was loaded by hand at all seven mines, though two employed partially mechanized longwall techniques. Wood posts were by far the most common ground support. Roof bolts were not observed in use at any of the mines, and they are unlikely to replace timbers any time soon. While long-term entries generally appeared to be adequately supported, the survey found that less attention was paid to the temporary support that is installed right after the coal is removed. This temporary support is critical for protecting the workers from rock falls, however, because with hand-loading mining methods most of the activity takes place between the permanent supports and face. The study concluded that improving the temporary support in the working faces would be the most effective way to reduce the number of rock fall injuries. The key principle should be that every worker is protected by planned roof support at all times. Ground Support Management Plans, consisting of specific rules about when, where, and what roof support is to be installed, should be the focus of the campaign. Each Plan should be tailored to a specific mine based on the geologic conditions and mining methods in use. The Plan provides miners with clear, simple rules that can be easily understood, while management can easily check to see if it is being followed. Ground Support Management Plans will also provide the campaign with a concrete focus for the necessary cultural change.

Jan 1, 2014

According to the classification of water conservation mining in shallow coal seams in China, when the ratio of the impermeable layer thickness to the mining height is less than 18, the mining belongs to the category of special water conservation, and the strip backfilling mining method is employed. This study is based on the geological conditions in northern Shaanxi. By analyzing the stability of the impermeable layer, the stability criterion of the impermeable layer was developed. The study also investigated the compositions and properties of the backfilling materials. The results show that reasonable subsidence of the impermeable layer is allowed during mining under the basic precondition (upward cracks and downward cracks are not connected).

Jan 7, 2020

By Paul C. Schmall, John F. Donohoe, Arthur B. Corwin, Derek Maishman

Ground freezing was utilized to provide complete stability of the excavation face and complete groundwater cut-off for the jacking of the three tunnel boxes for the Interstate 90 / Interstate 93 approach to the Fort Point Channel crossing. Through a wide range of geological conditions and large buried obstructions, the freezing provided complete stability of the face so that a 11.5 m (38 ft) high free standing vertical face could be mined without the need for any additional face support. Obstructions were incorporated into the massive frozen ground matrix, and held in place so that they could be excavated with a minimum of disturbance. The freezing provided an absolute groundwater cut-off, and permitted the work to be done without disturbance to the active rail system immediately above. With the use of instrumentation such as borehole thermocouples, the effectiveness of the freezing was guaranteed and the jacking proceeded with complete confidence and assurance of the ground conditions ahead.

Jan 1, 2001

By Daniel Mageau

Ground freezing has been used for over 100 years to provide shoring and ground water cutoffs for hundreds of projects worldwide, including drilled shafts, tunnels and cofferdams. Typically, these cases involved difficult soil/water problems where ground freezing was likely the only solution. This paper discusses a recent ground freezing project where a frozen soil wall was used for a more conventional problem. A 4-foot-thick frozen soil wall was used to provide shoring and groundwater cutoff for a 20-foot-deep excavation during construction of a cast-in-place concrete storm water detention vault. The site is located along the northbound on-ramp to I405 from westbound SR522 in Woodinville, Washington. The frozen soil wall was successfully formed in soils consisting of till fill over soft organic silt and loose saturated sand in about 3 weeks. The depth to ground water varied from about 4 to 8 feet over the site. The unfrozen soil inside the frozen soil wall was excavated vertically to the frozen soil boundary. The vertical excavation remained open for approximately 2 months with no dewatering required. On one side, fully-loaded dump trucks and other construction equipment operated within 6 feet of the wall face with zero wall movement. This paper addresses the construction issues related to installation and operation of ground freezing shoring. The overall wall performance of the frozen soil wall as well as basic geotechnical design issues are also discussed.

Jan 1, 1998

By Gregory T. Ziegler

A complex soil profile and high water table, together with a below-grade active subway tunnel, an above-ground elevated railway line, and the heavily travelled Northern Boulevard all passing above the tunnel alignment, combined to make mining of New York?s Northern Boulevard Crossing what is widely considered to be the most challenging portion of the multi-billion-dollar East Side Access project. The Northern Boulevard Crossing is a vital link in this project which, when completed, will connect the Long Island Railroad to Grand Central Terminal in Manhattan. How the sequential excavation method (SEM) tunneling was successfully accomplished, despite the obstacles, was a textbook exercise in practical innovation coupled with close cooperation between the owner, the construction manager, Hatch Mott MacDonald, the designer, Parsons Brinckerhoff, the contractor, Schiavone-Kiewit, and spe-cialty geotechnical contractor, Moretrench.

Sep 1, 2013

By Paul C. Schmall, Lucian P. Spiteri, Arthur B. Corwin

Moving groundwater is generally recognized as the most adversarial condition for ground freezing. Moving groundwater can occur due to natural or man-induced groundwater flow, but either way may result in freeze formation difficulties. History has shown that if the condition goes undetected, catastrophic failure of the frozen shaft or excavation can occur. The success of ground freezing under potentially flowing groundwater conditions depends on an evaluation of the likelihood for this condition; an accurate and early diagnosis, with a careful evaluation of freeze pipe temperatures and piezometer water levels; and timely reaction to mitigate the possible delays. Successful remedial measures have included the reduction of ground permeability by modifying the soil properties between the freeze pipes with various kinds of grouting, or increasing the freezing effect by adding freeze pipes and/or the use of liquid nitrogen as the freezing agent.

Jan 1, 2007

By E. Douglas, V. M. Malhotra

"This report presents the results of a laboratory study undertaken to evaluate ground granulated blast-furnace slag from Algoma Steel Corporation, as a replacement for Portland cement in cemented mine backfill. The evaluation was based on the results of compressive strength tests performed on cylinders cast from mixtures made with a granulated blast-furnace slag and tailings from four different mines in the Sudbury basin. Various percent¬ages of slags and various binder to tailings ratios were used.Tests results show that, in terms of compressive strength, the slag performs as well or better than Portland cement as the binding agent in cemented mine backfill. Lime was found to be a poten¬tially good activator for ground granulated slag in mine backfill applications.A field test was conducted at one of the mines, consisting of placing a mixture of 95.5% ground granulated slag and 0.5% lime into a stope, and inspecting the floor slab as it hardened. The slag performed as expected, considering the backfill mixture proportions used and the preparation of the test site."

Jan 1, 1989

By Peter White

A bridge reconstruction project involved driving pipe piles for the new foundations. Disturbances within soil layers at depth caused sinkholes to open up within the construction site. After a near fatal accident, the pile driving installations were suspended. The solution involved ground im­provement through cement grouting with sleeve pipes and special grout additives to minimize migration of cement grout.

Jan 1, 1997

By M. Kumaran, A. Vetriselvan, A. Purantharan

"This paper presents a case history of evaluating the stability of a distressed earth bund and rectification measures carried out. A 5.45 km long, 7m high earth bund for drinking water storage was constructed in Andhra Pradesh. During construction of the bund following were observed – (a) a longitudinal crack at the downstream side (b) Bund on the downstream side along the crack settled to a max of 700 mm and (c) downstream rock toe level area raised by heave up to 175 mm. Investigation of the events made important contributions to the fundamental understanding of the behaviour of large earthworks of this type. It was found that the variation in subsoil strata was not addressed during the execution.After careful evaluation, stone columns were recommended as a suitable ground improvement technique. Stone columns were used as a reinforcement to improve the shearing resistance of foundation and in turn ensure stability. By using and applying advanced geotechnical engineering analysis tools and modelling techniques, earth bund and its foundation was analysed and examined against failure by slope instability. Stone column design was carried out using in-house computer program GEOSTONECOL and stability of earth bund was analysed using TALREN software. Earth bund construction was completed after ground improvement and is performing satisfactorily.INTRODUCTIONIn order to supply water during summer season, Government of Andhra Pradesh decided to construct a 7m high and 5.45km long earth bund summer storage tank. It was one of the largest earth bund summer storage tanks in whole of South India at the time of its construction. During construction, the earth bund has undergone sudden distresses. Investigation of the series of events occurred during construction has made important contributions to the fundamental understanding of the behaviour of large earthworks of this type. This paper presents the reasons for earth bund failure, slope stability assessment of the distressed earth bund and recommendation of stone column as a suitable ground improvement remediation technique.DESCRIPTION OF STUDY SITEThe characteristics of the original construction are briefly described as follows. A shallow cut-off trench was excavated below existing ground level at the centreline of bund as shown in Fig. 1. Below the base of the trench a cut-off grout curtain was installed. Upstream and downstream shell earth filling was carried out using Clayey Sand ‘SC’ type soil. At some locations, bottom of cut-off trench has reached as deep as 12m from the existing ground level."

Jan 1, 2017

By Narendra N. Khatri, Michael Deutscher, Jozef F. Zurawski

Five sewer connections were required to divert Combined Sewer Overflow (CSO)from existing outfalls to an old underutilized large diameter brick sewer (the Easterly Interceptor). The connections were part of an on-going CSO control program by the Northeast Ohio Regional Sewer District (NEORSD) in the City of Cleveland, Ohio. Each connection was made by pipejacking and hand-mining a fiberglass-reinforced polymer (FRP) pipe through soft glaciolacustrine clays and silts. Jet grouting was utilized to stabilize the soils and fill the voids surrounding the interceptor prior to making the underground connection. Reinforced concrete liners were constructed inside the aging brick sewer to provide structural stability during ground improvements and connection work. The project also involved micro tunneling two approximately400 foot lengths of FRP pipe through soft ground using a slurry pressure balanced machine.

Jan 1, 2005

Coal bursts are one of the least understood yet the most critical hazards in underground coal mines. The ground motions induced by seismic events can trigger unstable failure of coal and rock mass and degrade the surroundings of an excavation. Therefore, the characteristics of ground motions should be fully investigated for an improved burst risk management. This paper analyzes ground motion features of a longwall panel from a typical underground burst-prone coal mine in China. The results showed that most of the ground motions on roadways were hardly initiate coal bursts due to insignificant energy input to the damage. The intensity of ground motions in near-field zone were nearly 20 times higher than those in far-field zone. The strongest vibration on roadway was induced by a coal burst with energy of 28,600 kJ, which can cause ground motion of 0.77 m/s and equivalent dynamic stress of 14.69 MPa. The findings of this paper can improve the assessment of seismic risks and its management.

Jan 7, 2020

By Professor of Civil and Environmental Engineering Northwestern University, Mike Wladron, Gordon Revey

A unique judicial opportunity allowed measurement of the response of three cracks in residential structure to blasting for underground aggregate mining. Instrumented cracks were located in the interior basement CMU mortar and upstairs dry wall as well as exterior brickwork. The dynamic environment was unusual. Even though the blasting occurred some 490 m (1600 ft) away, excitation frequencies were unusually high and there were no apparent surface waves. In addition there was no air overpressure wave to produce secondary crack response. As is typical, long term environmental effects produced greater crack response than did the blast induced ground motions.

Jan 1, 2007

By Harry G. Poulos

Ground movements can arise from a large number of sources and can have a significant effect on nearby piles and deep foundations. The loading of the piles by ground movements is a different mechanism to that arising from direct applied loading to the pile head, and consequently it is not generally possible to adequately analyze the effects of ground movements simply by applying some type of equivalent loading to the pile head. The main effects of ground movements are the development of additional movements, axial forces and bending moments in the piles, and thus the key design aspects are related to movements and to the structural integrity of the pile. However, the ultimate geotechnical load carrying capacity is generally not affected by the ground movements themselves. This paper will describe an approach to the analysis of ground movement effects on piles, considering axial and lateral movements separately. Some of the main features of pile response will be discussed for three specific problems involving ground movements: piles near and within embankments, piles near an excavation for a pile cap, and piles subjected to seismic ground motions.

Jan 1, 2006

By Harry G. Poulos

Ground movements can arise from a large number of sources and can have a significant effect on nearby piles and deep foundations. The loading of the piles by ground movements is a different mechanism to that arising from direct applied loading to the pile head, and consequently it is not generally possible to adequately analyze the effects of ground movements simply by applying some type of equivalent loading to the pile head. The main effects of ground movements are the development of additional movements, axial forces and bending moments in the piles, and thus the key design aspects are related to movements and to the structural integrity of the pile. However, the ultimate geotechnical load carrying capacity is generally not affected by the ground movements themselves. This paper will describe an approach to the analysis of ground movement effects on piles, considering axial and lateral movements separately. Some of the main features of pile response will be discussed for three specific problems involving ground movements: 1. Piles near and within embankments; 2. Piles near an excavation for a pile cap; 3. Piles subjected to seismic ground motions.

Jan 1, 2007

By Robert W. Bruhn

An investigation was male of ground response to pillar retreat mining in a 1.7 meter thick seam at 108 meter depth at a site in northern West Virginia. This paper describes mining-related stress changes and movements at nine level, displacements within the overburden, ground surface subsidence and groundwater level variations. Subsidence approached 40 per cent of the nine height ad continued more than a year after mining. Water levels declined la certain deep-lying strata.

Jan 1, 1984

Open cut mining of the Black Rock chalcocite ore started in 1963. A ground movement monitoring programme was commencing in the early stages of mining when signs of instabilityof the western wall became apparent. Eventually 100.000 cu vd, of overburden Were removed beyond the rim of the western wall in an attempt to stabilize the slope. Subsequent decpenlug and mining till the final batter angle of 45 resulted in deterioration and mining was stopped 38 ft short in the ulltimte design deplh of 520 ft.Investigations showed that the geology of the western wall , was a major factor in the instability of this wall. A block jointed model was made 10 illustrate some of the pehomena observed. Quallatative agreement was found between the model deformation and the field measurements obtained.The results of the monitoring programme clearly show the value of this work In respect to the conlrol of the mining operatIon...

Jan 1, 1968

By G. Sauer

"More Skill is needed to avoid rather than to handle heavy ground loads." This finding, from a tunneling engineer of the nineteenth century, is still relevant today with all advanced sequential excavation and support methods available whether they are applied in the vertical or horizontal direction. Balanced contractual agreements and documents are important since they provide the spirit and climate at the site. This article aims to describe the means and measures for 'hand mined' shaft and tunnel support as they are available today. Some special construction elements and methods with a perspective in recent developments in order to avoid getting stuck in conservatism are presented as well. If we don't allow new methods, means and measures we may end up with the famous quote "Only women who have already proven they are able to give birth to a healthy baby are allowed to become pregnant!"

Jan 1, 2003

Ground support audits are sometimes necessary in ageing underground mines. Usually, the purpose of such audits is to assess the state of the ground support in various parts of the mine, identify areas that require attention and establish rehabilitation requirements. In 2005, Brunswick Mine, located in Bathurst, New Brunswick, Canada, completed a comprehensive mine-wide ground support audit. The areas examined included excavations in several mining blocks, as well as ramps, shaft stations, garages, shops, etc., throughout the mine. A vast amount of data was collected over a period of two weeks by multiple auditing teams. The audit was followed by a data digitisation exercise, and the creation of a data management system to store audit results and keep track of subsequent rehabilitation activities as they occur. One aspect of the data management system was the incorporation of a function for reporting on ground rehabilitation progress, along with the capability of updating mine level plans for easy visual presentation of this progress. This article describes the approach implemented at the mine to carry-out the audit, as well as the database constructed to manage the results.

May 1, 2009

By Helmut Hass, Marco Ziller

"Abstract: 1 Sophia Spoortunnel Marco Ziller, Trevi S.p.A.:For the construction of 14 cross passages connecting the twin tunnels of the Sophiaspoortunnel the Artificial Ground Freezing technique was applied as temporary soil improvement. AGF by Brine and Liquid Nitrogen was implemented. Automatic data acquisition and recording systems were installed to monitor the variation of the temperatures in the soil during the freezing intervention in order to control the behaviour and the efficacy of the treatment.IntroductionThe Sophia rail tunnel is a bored tunnel with a length of 4.24 km, comprising two separate parallel tubes with an outside diameter of 9.45 m. The twin tunnels were excavated by a TBM equipped with hydroshield. Seven service shafts, approximately 30 m deep, were constructed in between the tunnels. From each shaft two cross passages were constructed connecting the shaft with both tubes, for a total of 14 cross passages.The Artificial Ground Freezing technique utilizing both the Brine and Liquid Nitrogen methods was used for temporary waterproofing and soil support to allow the excavation of the cross passages. The natural soil to be frozen was consisting in loose sand and clay under a hydrostatic pressure up to 250 kPa.For the measurement of the ground temperature. Automatic data acquisition and recording systems were installed to monitor the variation of the temperatures in the soil and at the contact with the tunnel lining. Furthermore, a comprehensive computerized system of sensors and cryogenic valves was designed and implemented in order to manage the whole Nitrogen process.Soil Main CharacteristicsThe soil stratigraphy is generally consisting in Clay (Holocene) from ground level to -15 m depth, followed by Pleistocenic Sand, from -15 to -25 m, and Clay below -25 m."

Jan 1, 2014

Tunnelling under squeezing ground conditions poses significant challenges. There are fundamental differences in the choice of support for mining as opposed to civil engineering. This paper reviews ground support strategies that have been used to control large deformations in mining excavations based on field data from five different mines in Australia and Canada. Recommendations are made for improved ground control strategies in squeezing rock conditions.

Jan 1, 2008