Search Documents

By Fred N. Kissell

In This Chapter [The explosibility of methane gas mixtures Effect of pressure and temperature on explosibility Less common sources of methane ignitions The amount of methane stored in coal Forecasting the methane emission rate Layering of methane at the mine roof When the recirculation of mine air is hazardous The importance of higher air velocity in preventing methane explosions and Mine explosions, barometric pressure, and the seasonal trend in explosions] Dealing with methane in mines and tunnels requires knowledge of the circumstances under which dangerous accumulations of methane are likely to occur. This knowledge involves the properties of the gas itself, an awareness of where these accumulations are likely to occur, and facts on how methane mixes safely into the mine air. The other chapters in this handbook address the handling of methane under a variety of specific circumstances, such as at continuous miner faces or coal storage silos. This chapter addresses some broad concepts that serve as a foundation for the suggestions provided in other chapters. THE EXPLOSIBILITY OF METHANE GAS MIXTURES Methane entering a mine or tunnel often enters as a localized source at high concentration. Figure 1–1 depicts a cloud of methane being diluted into a moving air stream. In this illustration, methane enters the mine from a crack in the roof. As the methane emerges from the crack, it progressively mixes with the ventilation air and is diluted. In the event that this progressive dilution reduces the concentration from 100% to 1%,2 as shown in Figure 1–1, the methane passes through a concentration range of 15% to 5%, known as the explosive range. In the explosive range, the mixture may be ignited. Above 15%, called the upper explosive limit (UEL), methane-air mixtures are not explosive, but will become explosive when mixed with more air.

Jan 6, 2006

By J. Paraszczak

High productivity of the equipment employed is one of the key factors in reducing production cost in mining. One of the best ways to achieve it is an increase in availability. In order to identify the most adverse factors affecting it, reliability and maintainability analysis ought to be done. If its results are to be conclusive, a sufficient amount of credible and consistent data is indispensable. Following the experience from field studies done in underground mines, this paper discusses the current status of failure and maintenance reporting, as well as problems encountered. It exposes the importance of adequate data collection on failures and downtime as well as it reviews the benefits of analysis based on such material. The question of benchmarking with regards to mining equipment performance is also addressed. The paper concludes with some recommendations on data collection and processing, as well as stresses the need to standardize the most important reliability/ maintenance notions throughout the mining industry and to conceive appropriate performance measures.

Jan 1, 2000

By Yingxin Zhou

Virtually every coal seam in Appalachia will at some time be subject to multi-seam interaction (Wu et al, 1987). Many such problems result from seams which lie in close proximity or have split and lie within thirty feet vertically of one another. Existing techniques for multi- seam design have concentrated on conditions where the entire inner burden is not the failing member and are unsuitable for ultra-close multi-seam design. Structural integrity of the inner burden must be maintained if two superimposed seams are to be mined separately and under- standing possible failure mechanisms of the inner burden is an essential first step in the design process.

Jan 1, 1989

By King E. J

Department of Pathology, British Post-graduate Medical School, London:The experiments here recorded were devised and carried -out during the last two years in an attempt to corroborate the important work of Denny, Robson and Irwin (1939) in which they found that experimental silicosis could be prevented by means of metallic aluminum. By causing rabbits to inhale powdered quartz for several months they induced experimental silicosis. These animals then served as controls for comparison with another group which were dusted with a mixture of quartz and aluminum. In the second group silicosis failed to develop.Our experimental procedure was somewhat different. We resorted to intratracheal insufflation instead of simple inhalation, and we used rats instead of rabbits: otherwise the essential features of the original experiments were carefully duplicated.EXPERIMENTAL PROCEDURES.A single dose of dust was delivered into the lungs of each animal. The dust was suspended in a fluid medium and injected by means of a syringe directly into the trachea in known quantity (technique of Kettle and Hilton, 1932). The suspensions were autoclaved before use and were injected with aseptic precautions. Having had a long experience of this technique we employed it with confidence and usually secured a fairly uniform dispersal of dust throughout both lungs. To carry out injections successfully one requires, above all, an even suspension of dust which will flow smoothly and quickly from the syringe. This is not difficult in the case of quartz, for, though it tends to settle out rather quickly, this can be avoided by constantly agitating the suspension. The syringe containing the inoculum may be shaken gently right up to the moment of injection and then emptied quickly to prevent sedimentation. Powdered aluminum is more difficult to handle, for the particles tend to flocculate and are not readily made to disperse evenly in saline, even by violent shaking. For this reason an emulsifying agent may be used to advantage, provided it does not complicate the experiment, a point to be mentioned again presently.THE EXPERIMENTSExperiments with quartz alone: Extensive silicotic lesions were produced in 23 out of 26 rats by the administration of pure quartz dust in doses of from 50 to 200 mg. per rat. The dust was so finely pulverised that the particles averaged about 1-p. in size: none was larger than 5 p. and 99 per cent. were under 2.5 p.Eight of these animals survived for seven months and were then killed...

Jan 1, 1945

Abstract : The computation of reliability index or failure probability of slopes can be transformed into an optimisation problem. In high rock slope engineering, it is usually a multimodal optimization problem. The traditional optimization techniques are difficulty to find out the global optimal solution because of their easily falling into local optimal value. Recently, a new kind of bionic algorithm - ant colony algorithm (ACA) - has been used to solve this problem. In this paper, the structure of ant colony algorithm and the transfer probability of ants are modified to evaluate the failure probability of complicated slopes. A new adaptive ant colony algorithm (AACA) is proposed to determine critical slip surface and its corresponding failure probability of complicated slopes. A case study is given to verify the proposed approach. The results show that the presented method has obvious advantages compared with traditional methods. ZUSAMMENFASSUNG: Die Rechnung des Zuverlaessigkeitindexes oder der Zerstoerungswahrscheinlichkeit kann sich in einer Optimierungsfrage umwandeln, im Bauprojekt an hoehe Gebirgehang, handelt es sich meistens um eine Optimierungsfrage ueber Multi- Spitzenwert. Mit der traditionelle Optimierungsmethode ist es schwer eine umfassende Loesung fuer die Optimierung zu finden wegen des leichte Verfallens in Beschraenkung der Teiloptimierungsloesung. Mit dem neue Bionik- Algorithmus —— Ameisen - Kolonie- Algorithmus wird dieses Problem geloest. In diesem Text hat man eine Strukturverbesserungsloesung fuer das Ameisen- Kolonie -system und die Wahrscheinlichkeit der Ameisenkolonie erwaehnt, und damit wird man die Zerstoerungswahrscheinlichkeit des komplizierte Hangs feststellen. Mit dem neuen Ameisen- Kolonie- Algorithmus kann man die gefaehrlichste Gleitflaeche und die entsprechende Zerstoerungswahrscheinlichkeit herausfinden. Die in diesem Text beschriebene Methode wurde durch Praxis geprueft. Durch die Pruefergebnisse wurde es gezeigt und bestaetigt, dass der neue Bionik- Algorithmus vorteilhafter als der traditionelle Algorithmus ist. Résumé : Le calcul de l’indice la fiabilité ou de la probabilité de ruptures peut être transformé en un problème de l’optimisation. Pour le cas du génie des pentes de haut rocher , le problème se pose en général en l’optimisation de multi-crêtes. Les techniques traditionnelles conduisent facilement à la solution optimal partielle au lieu de celle globale. Récemment un nouveau type de bionique algorithmique a été appliqué pour la solution de ce genre de problèmes, c’est l’Algorithme Colonie de Fourmis. Dans l’article il est proposé de modifier la structure du système de la colonie de fourmis et la probabilité de transfert des fourmis en vue d’évaluer la probabilité de ruptures des pentes de haut rocher complexes, par ailleurs un nouveau algorithme adapté de colonie de fourmis est formulé pour déterminer la surface glissante critique et la probabilité de ruptures correspondante. Les techniques proposées dans l’article sont vérifiées à travers des expérimentations dont les résultats ont prouvé que les techniques présentées dans l’article sont évidemment meilleures que celles traditionnelles.

Jan 1, 2003

By Walter F. Atkins

Fair market value, in the legal sense , is the price which a prudent and knowledgeable buyer and a prudent and knowledgeable seller, acting without constraint or compulsion , will agree upon to exchange an asset. In the ordinary commercial or engineering usage, the term may imply simply the market value or a reasonable and equitable price. The engineer evaluator who is called upon to express an opinion about the fair market value of an asset may be able to base his estimate on the sale price of similar assets or on the market values of stock. Frequently such indicators of value are not available and the evaluator must devise other means of appraisal. Mineral resource properties may be thought of as having value by virtue of the existing or potential ability to produce at a profit. Conventional procedures permit the computation of the present value of future revenues having due regard for the time value of money and the risks attendant upon the realization of the venture. Such computations have gained wide acceptance as a basis for the estimation of fair market value.

Jan 1, 1977

By N. L. ALISON

MUCH has been published on the general subject of metal mine ventilation but, so far as I can discover, few specific data on selection of fan equipment to meet the requirements of a given mine ventilation problem are available. This article is intended to point out some of the more important considerations which influence the selection of such equipment. It will be assumed that the mine operator is able to determine the quantity of air which is necessary in the various parts of his mine to produce the required results and the pressure in inches water gage needed to circulate this quantity of air through the mine. There may be instances in which this assumption is not justified, but the fact remains that, with proper engineering talent, these data can be approximated sufficiently close for practical purposes.

Jan 1, 1930

By B. G. Tarasov

This paper proposes the further development of a recently identified shear rupture mechanism (fan mechanism) that elucidates a paradoxical feature of hard rocks ? the possibility of shear rupture propagation through a highly confined intact rock mass at shear stresses that can be significantly less than frictional strength. In the fan mechanism, failure is associated with consecutive creation of small slabs (known as ?domino blocks?) from the intact rock in the rupture tip, driven by a fan-shaped domino structure representing the rupture head. The fan head combines such unique features as extremely low shear resistance, self-sustaining stress intensification, and self-unbalancing conditions. Consequently, the failure process caused by the mechanism is inevitably spontaneous and violent. Physical and mathematical models explain unique and paradoxical features of the mechanism, which can be generated in primary ruptures and segmented faults. The fan mechanism provides a novel point of view for understanding the nature of spontaneous failure processes, including shear rupture rockbursts. The process explains, in particular, features of shear rupture rockbursts such as activation at great depths, generation of new shear ruptures in intact rock mass, nucleation of hypocentres at significant distances from the excavation, shear rupture development at low shear stresses, and abnormal rupture violence.

Jan 1, 2014

The spatial and temporal evolution from the porphyry to high-sulphidation epithermal environment can be assessed by integrating new results on such deposits (Arribas et al, 1995; Hedenquist et al, 1998) with past studies of plutonic and porphyry systems (Dilles and Proffett, 1995; Cline, 1995; Shinohara and Hedenquist, 1997; Hedenquist and Richards, 1998). Some time ago, Sillitoe (1973) argued for the nature of the tops and bottoms of porphyry deposits. He concluded that epithermal deposits may form over the tops of some porphyry systems. We can now conclude more confidently what the tops and bottoms of many high-sulphidation ore deposits appeared like while active (Arribas, 1995; Hedenquist, 1995). In addition, we better understand the nature of the zonation of high-sulphidation epithermal systems from the intrusive to surficial environment (Sillitoe, 1999), and how these two styles of ore deposit are related. Geological and geochemical evidence clearly indicates a continuum between these two ore environments. This improved understanding of genesis allows more efficient exploration for these deposits. There are many examples of spatially associated porphyry and epithermal ore deposits. A genetic connection has been suggested by some, and argued against by others. Nowhere is this spatial association better seen than in northern Luzon, Philippines, where the Lepanto high-sulphidation epithermal Cu-Au deposit overlies the Far Southeast (FSE) porphyry Cu-Au resource (Figure 1). Together these mineralised bodies contain a resource of >3.8 M tonnes Cu and >550 tonnes Au. Lepanto was largely mined out in early-1997. Post-war production until 1995 was 0.73 Mt Cu, 115 t Au and 393 t Ag at an average grade of 2.2 per cent Cu, 3.5 g/t Au and 11 g/t Ag. The recent discovery of the adjacent Victoria low-sulphidation quartz-Au-base metal vein deposit, with a resource of >68 tonnes Au (Cuison et al, 1998), illustrates the variety and abundance of mineralisation in the Mankayan district. This district also hosts the Guinaoang porphyry Cu-Au deposit (Sillitoe and Angeles, 1985) and other epithermal vein occurrences (Figure 1). This brief summary reviews the results recently published on the Lepanto-FSE deposits (Arribas et al, 1995; Mancano and Campbell, 1995; Claveria, 1998; Hedenquist et al, 1998), and stresses the evidence for coupling of mineralisation between the porphyry and high-sulphidation epithermal environments.

Jan 1, 1999

By Robert Hopler

In issuing this pamphlet on stump and boulder blasting for the use of farmers, we wish to call attention to the fact that Du Pont High Explosives have been used with universal satisfaction for many years under diverse conditions, and have never failed to give satisfaction in mining, quarrying, roadmaking, blasting stumps and boulders, or for any other work where regard to economy and safety in use is the object.

Jan 1, 2008

Fast Adsorption Phenomena at Air/Liquid Interfaces

Sep 13, 2010

Mine Evaluation Engineering , Operational and Social evaluation. Focus is on what opportunities are available. Social ??History ??Past Management Practices ??Community / Available labor force Mining Method / Equipment ??Competent rock ?little support required, no backfill ??Shallow mining ?ramp mining, no shafts or hoisting ??Large scale mining potential ??Simple rock breaking and crushing on surfaceMill Process ??Straightforward gold liberation process Create a Plan / Create a Team Following the feasibility 44-101. Key people were hired and a full operational Business Plan was developed. Focus is on how to get the job done. ??Scoping Study / Pre-Feasibility / Feasibility ??Operational Business Plan ??Hire key people ??Purchase key equipment

May 1, 2006

By B. Schoevaerts

The ever-increasing depth of mineral extraction presents a challenging environment for hard-rock underground mines. High in situ stresses and associated seismicity with potential rockburst hazards are the major decisive factors contributing to the choice of a ground support regime. Conventional ground support systems, designed primarily for static loads, are not always capable of providing safe working conditions for underground personnel in seismically active mines. Systems specifically developed to resist dynamic loading and allowing for larger deformations are therefore preferred alternatives. High-tensile chain-link mesh has a proven record of successful use in open cut operations in various rockfall barrier installations due to its high energy absorption capacity. It has also been used in underground operations in various parts of the world. Its application in South African underground mining, however, is limited due to the high labour intensity. This paper describes a method of mechanized installation of a chain-link mesh as evaluation at Gold Fields' South Deep Gold mine situated some 45 km south-west of Johannesburg. A purpose-built mechanized roll mesh handler, developed in Australia, was used in this trial. The handler is compatible with all standard multi-boom underground drill rigs and is operated utilizing the hydraulic circuit normally used for the feed arrangement. A number of key performance indicators have been specified as success criteria by Gold Fields: ? A 30% faster installation compared to the conventional methodology ? The mesh should sustain any blast damage when applied to the blasting face ? No unravelling of the mesh when cut ? No failure of mesh under normal conditions ? Reliability of the MESHA® installation handler (availability >90% ? Compatibility of the MESHA® installation handler with AC 282 boomers. Although the energy-absorbing mesh combined with yielding rockbolts is a ground support system of choice for rockburst-prone conditions, the operational upsides recognized during the trial imply that this product can also be competitively used in less demanding ground conditions where weld mesh or shotcrete are customarily used as a primary surface support.

Jan 1, 2012

This chapter presents an overview of fatal and nonfatal injuries reported to MSHA during 1986-1995. Reportable injuries follow the criteria for reporting specified in 30 CFR 50. These criteria are listed in appendix A. The data used for these analyses came from the MSHA accident, injury, and illness data closeout files for the years 1986-1995. The MSHA data are described in appendix A and methods used in data analysis in appendix B. There may be slight discrepancies between the figures presented here and other presentations of MSHA data for the following reasons: (1) injuries to nonemployees have been excluded from analysis; and (2) injuries identified by MSHA after the files were closed out are not included. Within the MSHA data, there are differences in reporting requirements for operators and contractors. Contractors are required to report only those injuries that occur during certain categories of work (described in appendix A). For this reason, data on injuries among employees of operators and contractors in the MSHA database should not be considered directly comparable. As discussed in the "Introduction," the MSHA data on fatal injuries differ from the CFOI data (chapter 1) because of varying definitions used for the mining industry. As compared to the CFOI data, MSHA data exclude injuries that occurred off of mine property and include injuries occurring at mills and processing plants on mine property. Tables 4-1 through 4-9 and figure 4-1 provide comparisons of injury frequencies and rates among the commodities. These comparisons are followed by sections 4A through 4E, which provide more detailed tables and figures for each commodity separately. The method used to calculate injury rates is described in appendix B. Since denominator data for occupations (lob titles) were available for 1986 only, estimates of rates by occupation for the entire 10 year period are based on extrapolation from 1986 data. For this reason, estimates of injury by occupation should be interpreted with caution. Fatal Injuries A total of 1,078 fatal on-the-job injuries were reported to MSHA during the 10-year period 1986- 1995. The average annual fatal injury rate for all commodities combined during this period was 30.9 per 100,000 full-time equivalent workers. Mine operators accounted for 908 (84%) of the fatalities and had an average annual fatal injury rate of 28.2 per 100,000. While mine contractors comprised only 16% (n = 170) of the total number of fatalities, their average annual fatal injury rate was 2.3 times higher than that of mine operators (65.0 per 100,000). Table 4-1 presents the number and rates of fatal injuries by commodity for operators and contractors. Contractors in metal, nonmetal, stone, and sand and gravel are grouped together, since MSHA data on employment were not available for rate calculations for these commodities separately. The highest average annual fatality rate for the period, 66.5 per 100,000, occurred among metal and nonmetallic mineral mining contractors, followed closely by coal contractors (63.1 per 100,000). Among mine operators, the highest average annual fatal injury rate was in coal (38.9 per 100,000); the lowest was in nonmetal (14.3 per 100,000). Table 4-2 shows the average annual fatal injury rate by type of operation for each commodity for mine operators only. Of commodities with underground mines, all except stone had higher fatality rates at underground than at surface operations of these mines. The highest fatality rate for any operation occurred in surface operations at underground stone mines (124.5 fatal injuries per 100,000 workers). Stone had the second highest fatality rate for underground operations at underground mines (77.9 per 100,000). The highest rate for underground operations at underground mines occurred in metal (87.6 per 100,000). Table 4-3 shows the number and rate of fatal injuries by U.S. Bureau of the Census occupational groups (described in appendix D) for the 10 occupation-commodity groups with the highest fatal injury rates. These data should be interpreted with caution because the denominator used in calculating the rates was based on an extrapolation from data for the year 1986 only, as described in appendix B. Extractive occupations are represented in this group for three commodities: coal, metal, and sand and gravel. Construction trades are included for coal, sand and gravel, and nonmetal. The distribution of fatal injuries by commodity and work activity for mine operators is presented in table 4-4. A description of the work activity categories is in appendix C. Overall, the leading work activity at the time of injury was using or operating tools and machinery (26.4%) followed by constructing, repairing, and cleaning (24.0%), vehicular operations (18.8%), and materials handling (12.6%). The distribution varied by commodity. The largest percentage of fatal injuries occurred while operating tools and machinery in both coal and stone; during vehicular operations in metal; and during constructing, repairing, and cleaning activities in nonmetal and sand and gravel. Table 4-5 shows the distribution of fatal injuries by commodity and MSHA accident classification for mine operators. A description of the MSHA accident classifications appears in appendix E. The largest proportion of injuries overall occurred during powered haulage (28.5%). The

Jan 5, 2000

By W. J. Theron

The purpose of the paper is to give an introduction to the concept of fatigue and its causes in the mining industry. By knowing the fundamental role it plays, together with its dynamics, can positively contribute to a mine?s safety management system. The difference between physical and psychological fatigue will be addressed with a possible range of causes that could trigger fatigue. There are two main sources of fatigue: firstly, work-related fatigue which is associated with activities at the workplace; and secondly non-work-related fatigue. The shared responsibility between the employer and employee is also discussed as it involves factors that occur both in and outside the workplace. Employers have the responsibility to manage fatigue through using a risk management approach. Employees have the responsibility to ensure they get enough sleep, take sufficient and regular nutrition, are healthy and physically fit and come to work fresh and alert. The impact of the implementation of a fatigue management plan and procedures has the potential to eliminate employee fatigue or its causes, reduce the likelihood of fatigue occurring in the workplace, and counteract the effects of fatigue when it occurs. Factors considered when implementing a fatigue management system include: extended hours of work, shift work, time of day and work design. Fatigue is one of the major role players (either causal or contributory) when it comes to causes of fatalities in the mining industry. Our main challenge in identifying whether fatigue played a role is the fact that it cannot be tested in post-mortems like drug or alcohol abuse. It is an aspect worth understanding and getting an organization sensitive to managing it properly to benefit both organizational as well as employee needs. Keywords Signs of fatigue: Causes of fatigue, circadian rhythms, the fatigue equation, fatigue management, fatigue affecting safety, fatigue fighting tips, lifestyle suggestions.

Jan 1, 2011

By M. Matema

Paper written on project work carried out in partial fulfilment of BSc (Eng.) Metallurgy and Materials Engineering Small and large welded aluminium specimens were tested in fatigue and the results compared with design curves for aluminium in specification BS8118. Metallurgical tests were also performed on the specimens in order to correlate microscopic and macroscopic phenomena. The small-scale fatigue test results were in reasonable agreement with results in BS8118, whereas the large-scale fatigue tests showed that BS8118 is conservative.

Jan 1, 2005

By P. C. Schutte

There have been several high-profile accidents in the South African mining industry where fatigue was identified as either causal or contributory. The risk of fatigue is inherent in any work-time arrangement involving shift work and work that is physically or mentally demanding, repetitive, or requires high vigilance. The management of fatigue is not simply a matter of correct shift scheduling. Amore comprehensive approach is needed. In order to be successful, a fatigue management programme should address the unique needs of the operation in which it will be implemented and should be integrated into normal operations. Fatigue management is a shared responsibility between the organization and its employees, and all stakeholders should participate in order to provide the safest and healthiest working environment possible.

Jan 1, 2010

By M Eggers, H Baxter

This paper discusses the geotechnical condition of bedding shears and small- and large-scale faults and shears in Archean banded iron formation (BIF) bedrock, based on observations of core and televiewer images. Information that can be collected includes the orientation of defects, infill thickness, strength and material type, defect shape and surface roughness.The spacing and continuity of bedding shears may be critical to slope design where performance is structurally controlled with bedding dipping out of a wall. The intensity of development of the bedding shear is a useful indicator of the amount of shearing a bedding surface has been subjected to. This can allow for engineering judgement to be used in adopting peak or residual shear strengths along defect surfaces when developing the design.The spacing and continuity of bedding shears may also contribute to the blockiness and degradation of a rock mass where the structural orientation is otherwise favourable. Additionally the condition, thickness and strength of infill of major fault structures can affect slope design and performance, depending on orientation.Comparison of the condition of structures observed in core with the corresponding in situ televiewer image has been made to assess what characteristics are most accurately captured by each technique and whether the additional information gathered from using the televiewer technique is justified by the cost. The question of whether the data collected by a televiewer is sufficient to ultimately replace the need for core is considered.CITATION:Baxter, H and Eggers, M, 2013. Fault and shear characterisation in archean banded iron formation bedrock - a comparison between core and televiewer data collection techniques, in Proceedings Iron Ore 2013 , pp 47-56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

Data recently released indicate substantial improvement in mineral industry performance for 1984. Business plans to increase plant and equipment spending in 1984 by 14.8 percent, according to a recent survey conducted by the Commerce Department's Bureau of Economic Analysis (table 1). In contrast, capital spending by all industries declined 4.8 percent in 1983 and 2.3 percent in 1982. The latest estimate of planned expenditures for 1984 is $2.2 billion higher than the comparable estimate based on the survey conducted in late January and February 1984.1/ [ ] Of particular significance to the U.S. mineral industries are the 15.5-percent increase in capital spending planned by manufacturing in 1984 and the planned 18.6-percent increase in spending by durable goods manufacturing, where the largest increases are planned in the transportation equipment (26.4 percent) and electrical machinery sectors (23.5 percent). Capital expenditures in manufacturing declined in both 1982 and 1983.

Jan 1, 1984

By Sastry Putcha, Vamshi Vemula, Aneesh Goly, Kumar Allady

Current dynamic testing practice to obtain pile total capacity will not yield optimum capacity due to the strain incompatibility between the side and tip resistances during driving. Superposition of end of initial drive- static tip capacity and the peak static skin capacity during beginning of restrike and adding them is the preferred method. The FDOT method determines independent pile static tip and skin capacities in real time analyzing appropriate blows from the embedded tip and top data of the Embedded Data Collectors (EDC). This data is collected through a wireless radio transmitter, receiver, and laptop software. The approach utilizes EDC tip and top data and nonlinear single degree of freedom system to satisfy force and energy equilibrium with a global genetic inversion analysis. Top impacted energy equals at pile tip as sum of Static, Damping and Inertial energy providing independent tip resistance. With EDC sensors as boundary conditions, pile is divided into desired segments and using global inversion techniques one dimensional equation is solved for independent skin friction for every blow. EDC data compared close static load test results. The EDC - FDOT method has enabled cost effective 100% testing of driven piles cost effective. INTRODUCTION Historical documentation has shown that not only driven piles have a long history of usage but also continues to advance unceasingly till today. Historians placed the first pile driving using timber piles in the 4th century BC. While modern pile driving systematically started around nineteenth century, the credit for conceiving the idea of the applicability of wave equation to driven piles goes to David Victor Isaccs of Australia. His 1931publication “Concrete Pile Driving Formulae” provides the basis for modern pile driving using stress wave theory. He felt that the dynamic formulae then in use lacked the capability of detecting integrity and hence developed stress wave theory. This work was further developed starting in 1938 by W.H. Glanville and colleagues of British Building Research Board as they developed the first solution to the wave equation. But these early efforts have really taken off only with the advent of computers. E.A.L. Smith (1960) published ‘Pile Driving Analysis with the Wave Equation’ and provided first numerical solution to the wave equation. Within few years, the FHWA funded research and in due course this effort ushered the era of externally instrumented pile driving.

Jan 1, 2018