Search Documents

By S. H. Ash, E. M. Brooks

"Many of the hoisting slopes at the mines in the State of Washington are driven on extra steep dips. To facilitate hoisting they are driven wide enough to provide two tracks. The cars are handled by high-speed, first-motion electric hoists and the trips run in balance.The State mining laws a provide that special man-cars be provided on slopes of 20° or more and that no one be allowed to ride while any loaded car is being hoisted in any slope in a mine. Obviously, in addition to the fact that it is more or less hazardous to ride while an empty trip is being hoisted, considerable hoisting time is lost during the day if some one has to ride the trips in the slope.Owing to the locations of pumps and various types of equipment, more or less travel is required up and down the slope. Not only to provide a proper safety factor but also to comply with the law, some other means of transportation in an¬other passageway is desirable. This is sometimes recognized in large mines by pro viding separate hoisting shafts, or slopes, and necessary equipment, which are use for transporting men and material. The handling of material in itself would justify the system in most large mines.The following description of an automatic electric man-hoist was prepared from data furnished through the courtesy of Mr. Thomas Murphy, superintendent of the Northwestern Improvement Company's mines in the Roslyn-Cle Elum coal field.The special features of this hoist are that no hoistman is required and its operation is always under the control of the person or persons riding the trip.The hoist was installed at mine No. 5, Roslyn, Washington, to provide a means of entering and leaving the mine on idle days or at night when no hoistman was on duty and to make it unnecessary to use the main hoist for a man trip during working hours. It has been in operation for about two years and has given very satisfactory service.The hoist, with all accessories, is housed in a concrete building 200 feet back from and in direct line with one of the main airways. One car with a capacity of six men operates over a distance of 1,200 feet on a 38° pitch.The wiring details of the electric circuits which control the operation of the hoist are shown in Figure 1-a.The hoist is driven through a worm gear by a 500-volt shunt-wound direct-current motor at a car speed of 120 feet per' minute. A gravity friction brake with magnetic release is mounted on the- motor shaft and is wired in multiple with the motor field coils. The hoist drum is also equipped with emergency friction brakes, which operate by gravity and are released, in case of overspeed, by the governor geared direct to the drum shaft. When these brakes set the control circuit is opened at contact 2E-2C and the motor stops.If the descending car meets some obstruction and is stopped, the hoist continues to run and unwind the rope. To guard against this occurrence, a weighted sheave wheel rides the rope 4 feet from the drum, and if the rope becomes slack the rider drops downward and opens the contact 2C-2E which stops the hoist.Limit switches, S1 and S2, are located on the hoist indicator, which is connected to the drum shaft through sprockets and chain. The pointer P indicates the position of the hoist at all times."

Jul 1, 1930

By Lloyd Williams

1. The investigation shows that the Poplar Creek and Big Mary beds contain the largest known recoverable reserves of coal in Morgan County, Tenn. The Poplar Creek bed has been the most productive. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 96 million tons, as of January 1, 1954. Of this total, 59 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By A. R. Kiani-Rashid

In this paper, the effect of aluminum content on the formation mechanism, volume fraction, morphology and particle size distribution of graphite has been investigated. Addition of aluminum on ductile iron causes some fundamental changes in iron-carbon phase-diagram and as a result, improves the graphite formation during eutectic transformation. The results reveals that aluminum compounds have been formed in the core of graphite nodules, thus aluminum plays an important role in the formation of graphite nodules. Furthermore, it is indicated that an increase in the aluminum content also leads to an increase in the number of graphite nodules and a decrease in the nodules size. By using EPMA, the segregation of aluminum and silicon between graphite nodules has been studied

Jan 1, 2010

By Michael W. Oakland

Deer Island is the site of the Massachusetts Water Resources Authority (MWRA) wastewater treatment plant which, when completed in 1999, will serve 43 cities and towns in central eastern Massachusetts. Deer Island is located in the Boston Harbor, as shown on Figure 1. The existing wastewater treatment plant on Deer Island is being upgraded to include secondary treatment to comply with Federal require­ments. The new treatment facilities will process an average of 455 million gallons of sewage per day; total capacity will be about one billion gallons per day. The new treatment facilities will cover virtually the entire island. [ ]

Jan 1, 1994

By Lonie W. M

The rapid development of the Australian steel industry over the past twenty years has greatly increased the demand for coking coal from the collieries owned by the Broken Hill Proprietary Co. Ltd. and Australian Iron & Steel Ltd. This in turn has called for an intensive and continuous programme of colliery expansion and new colliery development, along with the reorganization and modernization of existing collieries.This paper presents a general description of the factors involved and the techniques used in planning modern colliery development for the steel industry.PRELIMINARY GEOLOGICAL INVESTIGATIONSIn any colliery development, preliminary geological investigations require a detailed and practical knowledge of the geology and characteristics of the coal-field as a whole. In the early stages of the investigations, probably the most valuable information is obtained from outside the particular area under review, rather than within it, and unless the geology of the coal-field is understood, the projection of the known information into the unknown area cannot be carried out with certainty.Because development of the coal seams from the outcrops has been an apparently simple matter and not subject to the risks involved in deep mine development, the geology of the New South Wales. coal-fields has not received the attention that major mineral resources warrant.Only the most accessible regions of the coal measures have been generally prospected, while the potential areas remain...

Jan 1, 1957

By Clarence Karr

AN EXTENSIVE characterization was conducted on the neutral oil components in a low-temperature bituminous coal tar. A total of tai individual compounds identified with respect to individual isomers, and at least 55 other compounds were indicated to be present. The amounts were determined in all instances. A comparison of isomeric distribution in the tar with thermo-dynamic equilibrium distribution, and kinetic distributions indicated that the composition of the tar largely reflected the structure of the coal from which it was formed. Detailed descriptions are presented for the separatory and qualitative and quantitative procedures for the characterization of the neutral oil component. These include micro fractional vacuum distillation, displacement liquid chromatography, gas-liquid chromatography, countercurrent distribution, and infrared and ultraviolet spectrophotometry. Descriptions are given for the synthesis of authentic specimens of alkylindenes, The ultraviolet and infrared spectra of 134 polycyclic compounds, ranging from alkylindenes to alkylphenanthrenes, either found in the distillable neutral oil, or thought likely to be present, are also given.

Jan 1, 1967

By J. P. F. Charpin

The transport of large boulders in a furrow from a mining area to a nearby pond was considered. The furrow is filled with a mixture of water and soil particles flowing down to the pond at high velocity. Due to operating constraints, the slope of the furrow is reduced progressively. A relationship is derived, relating the slope of the furrow and the composition of the fluid to the maximum size and shape of the transported boulders. The characteristics of the boulders carried all the way down to the pond may then be determined.

Jan 1, 2007

By Zhang Chuanfu

Keywords: modified coprecipitation method, Ni-Co alloy powders, solid-solution oxalate, growth mechanism Homogeneous solid-solution oxalates of Ni2+ and Co2+ ions were synthesized by modified coprecipitation method and the composition and morphology of the fibrous solid-solution oxalates precursor were characterized by XRD, IR, DTA/TG and SEM analysis. The effects of feeding methods, pH values, precipitation temperature, reactant concentration, addition surfactant, alcohol washing and drying process on the morphology and dispersion of the precursor were investigated in detail. The experimental results showed that the coprecipitated powders have characteristics that are different from those of the mechanical mixtures with the same stoichiometry. Based on the observations of precursors growth and SEM morphology of the precursor, the oriented attachment was proposed for the well-aligned growth of the fibrous Ni-Co alloy precursor particles.

Jan 1, 2005

There has been a substantial increase in the use of rubber-tired front-end loaders in the mining industry in recent years. Concurrent with this increased usage, in the period of 1966 to 1970, there were at least 74 mining industry fatalities involving front-end loaders, or (on the average) in excess of one fatality per month. When the usage of front-end loaders by the construction industry and other industries, organizations, and agencies, such as the Government (i.e., Department of Defense), along with the uncounted numbers of serious, but non-fatal accidents, are included in the picture, the safety record for front-end loaders, of necessity, becomes a serious subject for study. There is an urgent need for attempts to be made to eliminate or reduce the number of safety hazards; to decrease the confusing diversity of controls designs found on present front-end loaders; to improve the maintenance and operating procedures; to formulate better personnel policies; to increase management and official awareness of the extent of the problem, in both industry and the Government; etc.; in order to decrease the number of accidents. Part of the problem may be traced to the fact that the operator of a front-end loader is frequently designated a "heavy equipment operator." This implies that he is automatically qualified to operate any model, of any manufacturer's, wheeled or tracked, front-end loader as well as many other types and classes of heavy equipment. Contrary to automotive practice, the complement of primary operating and emergency controls varies widely from model to model, as well as from manufacturer to manufacturer. Not only are certain controls present on one front-end loader model and absent on others, but there are significant differences in the modes of control operation, in the functions performed by superficially similar controls, in the location of the various controls, etc.

Jan 1, 1973

By N T. Moxon, L W. Armstrong

Explosive manufacturers have for many years provided a service to the mining industry which has,until recently, been unchallenged by mine operators. Today mine operators are more aware of the properties of explosives required to perform particular tasks within their operations. These properties can be reliably quantified using the test procedures described in this paper for emulsion adn ANFO based explosives. Details of an end-user sampling programme desgined to provide quality checks on explosives supplied to a mine site are also discussed.

Jan 1, 1991

By W. E. Lee

Penetration and dissolution mechanisms are reviewed for predominantly single-phase oxide, two phase oxide and oxide-carbon composite refractories by liquid silicate slags. Theoretical models of these processes, as well as static (sessile drop, dipping and crucible) and dynamic (rotating finger and rotary slag) experimental tests, along with their practical limitations are considered. Direct (congruent or homogeneous) attack is controlled by the reaction rate at the slag-refractory interface or the rate of diffusive transport of species to it through the slag leading to active corrosion. Indirect (incongruent or heterogeneous) attack is controlled by diffusive transport through the slag or through a new solid phase, which forms at the original slag-refractory interface. This may lead to passive corrosion. Examples of direct and indirect attack in a range of refractory/slag systems are described highlighting the critical influence of the composition and hence viscosity of the local liquid slag adjacent the solid refractory. Penetration and corrosion can be controlled either through the local slag composition via the refractory or the bulk slag or by microstructural control of the refractory by e.g. internal generation of dense layers or external deposition/generation of passive coatings, so-called in situ refractories.

Jan 1, 2004

By D. Imeson, T. Grammatikopoulos, M. Aghamirian, M. Oliazadeh

"More than 70% of potash is produced worldwide by froth flotation. Flotation of potash was developed in the early 1930s. Amines are widely used for flotation of sylvite (KCl) from halite (NaCl) and insoluble materials such as clays. Amine collector is also absorbed by clays. Therefore, clays are usually separated by scrubbing and de-sliming prior to flotation. Alternatively, slimes can be floated ahead of potash flotation. Flotation recoveries of sylvite are commonly in the range of 85%, while losses can occur in slimes, flotation tailings and make-up of process brine. Ores containing free coarse-grained sylvite are generally screened, whereas both fine and coarse fractions are conditioned and floated separately. The unique features of potash flotation include solubility of sylvite in water, the size of particles floated and fast kinetics. Particles up to 2.3 mm can be floated and about 50% of flotation feed can be removed in the rougher stage in few minutes. The main challenges in potash flotation are the recovery of potash from slimes, flotation efficiency in the presence of carnallite and recovery of coarse potash grains. A review of potash flotation shows that there is still room for improvement in both coarse and fine potash flotation. The present paper reviews the most significant flotation parameters including reagent type and dosage, flotation circuits, flotation equipment size and new developments in potash flotation. The latter include new reagents, flotation technologies (Hydrofloat, Jameson and column cells) larger flotation cells and slimes flotation.INTRODUCTION Potash is the common industrial term for potassium in various chemical combinations and minerals soluble in water. About 90% of potash produced worldwide is used as agricultural fertilizers. Flotation is the main treatment process of sylvinite (KCl-NaCl) ores for recovery of sylvite (KCl). Potash concentrate should contain a minimum of 95% KCl and be relatively free from 0.2 mm KCl fines. The flotation process for beneficiation of potash ores was developed in United States and Russia concurrently in the early 1930s. In 1934, Potash Corporation of America applied flotation process in a commercial scale (Tippin R.B. and Huiatt J.L). In the initial application, halite (NaCl) was selectively floated by employing lead chloride as an activator and soap as collector. The sylvite concentrate was reported in the cell underflow."

Jan 1, 2012

By W. Burger

Mechanical excavation methods can significantly improve excavation performance and labor safety compared to drill and blast operations. Herrenknecht has developed a mechanized shaft sinking method for soft and medium strength rock. This system combines innovative technologies which allow simultaneous excavation, removal of cut material and the installation of rock support. This Shaft Boring Roadheader ?SBR? is flexible in diameter and can be used in shafts with changing diameters and different shaft support requirements for depth up to 2,000 m. During regular excavation personnel are not required to access or work on the shaft bench. The boom used to cut the shaft profile is based on roadheader technology.

Jan 1, 2012

By C. B. Manula

Bituminous coal mining in the United States is currently experiencing a period of rapid growth which began in the early 1960's. Future demands are conservatively predicted to rise to 700 million tons by 1980 and to anywhere between 1 to 3 billion tons by the turn of the century. This means a continuous expansion of coal production by a factor of at least two can be expected before the end of the century. Over the last few years, production from underground mining has decreased; yet it is about 50% of the total coal output. In the absence of any discovery of near surface coal deposits, and even after conceding that some deeper deposits can be surface mined with changes in technology it can be reasonably assumed that coal production from underground will continue to play an important part in solving the energy crisis.

Jan 1, 1975

By P. Dhar, H. R. Kota, M. Thornhill

Precipitated calcium carbonate is used as a filler and coating material in the manufacturing of paper because of its high brightness and light scattering characteristics. However, beneficiated calcite has similar potential, given the fact that the industrial specifications are already achieved. For paper industries, the requirement is that the desired product should be pure and have a brightness of 93 to 95 percent. A very-high-grade calcite deposit of around 92 percent is located in the north of Norway, which is used as the raw material for ground calcium carbonate (GCC) feed for the paper industries. There is a substantial amount of calcite resource, which has pyrite and pyrrhotite as major impurities. These sulfides, even when present in minor concentrations, impart color to the end product (paper). Removing these minerals is estimated to increase utilization of the deposit by 10  percent, which represents several million tonnes of calcite marble. Due to the requirement for environmentally friendly reagents and chemicals by the mineral industry, fatty di-amines are being tested for pyrite and pyrrhotite flotation. The interaction mechanism of diamine with the main components of the ore were studied and optimum conditions for removal of sulfide impurities are outlined.

By H A. Myburgh

The beneficiation of heavy metal oxides, such as iron ore, is usually performed with heavy medium separation in cyclones, static baths and lately with Larcodems. Atomized ferrosilicon is most suitable as a heavy medium at densities above 3600 kg/m3 whereas a mixture of milled and atomized ferrosilicon is suitable at densities below 3600 kg/m3. When operating a beneficiation plant at densities higher than 3600 kg/m3 the quality of the ferrosilicon particles is an important factor that influences the control of the beneficiation process. Therefore, it is important to know how the rheology would be affected by the ferrosilicon quality as it also influences the control of the process at these elevated densities. Background The Kumba Resources Sishen Iron Ore Mine in South Africa produces 26.5 Mt iron ore per annum from its beneficiation plant. The ore body consists mainly of laminated and massive type hematite ore that is crushed down to ?90mm before being beneficiated by means of a combination of Wemco drums, Larcodem and dense medium cyclone separators. The need for higher densities When the percentage of high-density gangue2 is higher than normal in the run-of-mine (ROM), a higher separation density is necessary to produce a product to specification. Certain ore types of this quality in the Sishen reserves require a separating density higher than 4000 kg/m3, whereas densities would normally average 3600 kg/m3 when beneficiating ores of normal high-density gangue content. Sink and float tests conducted on the ROM material at Sishen revealed some interesting characteristics. In the waste fraction, (density < 3600 kg/m3) it was found that the %Fe was <21% (Fig. 1). Similarly, for the product fraction (density >3000 kg/m3), the percentage Fe varied between 35% and 67.2%. The bulk of the material (88%) actually had a density greater than 4000 kg/m3 and a Fe content that varied between 63% and 67.2%. At a density interval of 3600 to 4000 kg/m3, the Fe content varied from 37% to 60% with an average of 45%.

Jan 1, 2006

By Lukasz Maciag, Ryszard Andrzej Kotlinski, Ryszard Krzysztof Borówka, Dominik Zawadzki

Concentration and composition of rare earth elements (REE) and major elements in the sediment samples from the IOM H11 Fe-Mn nodule deposit, eastern part of the Clarion-Clipperton nodule field (located between the Clarion-Clipperton Fracture Zone - CCFZ; tropical Pacific), have been studied. We show the controls on REE concentrations and described vertical/horizontal variability of selected metals in pelagic sediments from the CCFZ. According to Kato et al. (2011), who analyzed 2000 seafloor sediment samples at 78 sites of the Pacific Ocean, deep-sea mud shows high concentrations (2230 ppm maximum) of ?REY and could be potential resource of these elements in the future. However, our work does not fully confirm that sediments in the IOM H11 are significantly enriched in REE.

Sep 1, 2014

By Esher Hsu

In Taiwan, around 8,000 tons of batteries are consumed per year but only 17% of which were collected and transported to oversea for recovery. The dumping used batteries have become a potential environment problem. How to increase the collection efficiency of used batteries is an important issue for EPA in Taiwan. Besides, some treatment plants are on process to get permission for recovering used batteries. The objective of this study is to estimate the recycling cost of spent consumer battery and explore the feasibility of recovering used consumer batteries in Taiwan based upon the principle of cost-efficiency. The recycling cost including collection cost and recovery is estimated based on a survey. Results would provide some suggestions to Taiwan EPA regarding feasibility of recovering used batteries in Taiwan.

Jan 1, 2006

By Carlos G. C

Geological mapping in various parts of Australia is revealing a number of regional associations of mineralizations with particular persistent stratigraphic horizons. Such associations have been found in the Broken Hill district of New South Wales, in the Nairne district of South Australia, in the Mount Isa district of Queensland, and in the Cloncurry district of Queensland. The question has arisen as to whether such mineralizations are of sedimentary origin, syngenetic with the enclosing formation, or whether they are of epigenetic origin, and reflect the selective hydrothermal mineralization of favourable beds on a regional scale.The purpose of this investigation is to test the use of sulphur-selenium ratios as an objective method of distinguishing between suphide deposits or sedimentary or supergene origin, and sulphide deposits of hydrothermal origin, with particular application to the districts mentioned. At the same time much data has been accumulated as to the selenium content of Australian sulphide ores. The possible use of sulphur-selenium ratios for this purpose was first demonstrated by Goldschmidt and his coworkers (1933; 1935), and later by Carstens (1941). Goldschmidt and Strock (1935) found that pyrite of sedimentary origin had a sulphur : selenium ratio of the order of 200,000 or more, whereas pyrite of hydrothermal origin had a sulphur: selenium ratio of 10,000 to 20,000. Carstensfound that sedimentary pyrite deposits in Norway contained less than 1 g. Se per ton, whereas hydrothermal pyrite deposits contained 20 to 30 g. per ton.

Jan 1, 1954

By Don C. Warrington

This paper is a survey of the various methods and research efforts by which the drivability of piles is determined. First, a brief outline of the basic theory and the important parameters for driving by vibration are presented. Then, a wide variety of methods by which the drivability of piles is determined are presented and discussed, with special emphasis on methods developed in the USSR. Each of these methods are examined as to how they take into account the various parameters of vibratory pile driving, such as eccentric moment, frequency, dynamic force, motor torque and power, vibrating and static weight, and other variables. Some relation of these methods of field data is presented as well.

Jan 1, 1989