Search Documents

The estimation of the shear stress distribution around an excavation is important to the design of the excavation since shear stresses can generate cracks, loosen grain boundaries or otherwise degrade the mechanical and physical properties of the rock and lead to stability problems. In this study, the distribution of shear stresses in a pillar were back-calculated from the deformation measurements made from the SPDV (Site and Preliminary Design Validation) area at the Waste Isolation Pilot Plant (WIPP) site. A plausible pattern of shear stress around an excavation has been suggested based on the Zero Strain Boundary (ZSB) calculation, computer simulation using FLAC, and back-calculation using measured deformation rates in the pillars.

Jan 1, 1998

By T Baumgartl, D R. Mulligan, D Doley, A Schneider

In arid and semi-arid areas evapotranspiration (ET) cover systems are often used to mitigate contaminated seepage from hazardous mine waste into the adjacent environment. The theory of ET covers is based on the water balance equation with the aim of minimising seepage. While cover systems are commonly trialled, the influences of variability in climate and cover structure on water balance equation parameters are seldom investigated.Water balance equation parameters and their variability were analysed for two ET cover trials constructed from benign waste rock in semi-arid Australia. Seasonal and inter-annual variations in rainfall critically influence cover performance. For successful cover system operation, the average return periods for higher than average rainfall should be taken into account. In addition, failure of ET covers has a higher probability in areas with marked rainfall seasonality. Water holding capacity and plant available water content are low in covers constructed from waste rock. Changes in water holding capacity due to variation in particle size distribution are likely and critically influence cover performance. The application of topsoil can be beneficial for water ingress control through run-off, but a balance has to be struck between run-off, erosion and plant available water. Changes in vegetation composition only influence evapotranspiration water losses at plant coverage exceeding 50 per cent, which is unrealistic in semi-arid areas. This study showed that the capacity of ET cover systems to hold and dispose of received rainfall is often lower than assumed by industry practitioners. Furthermore, in order to improve reliability of long term cover performance, the variability of rainfall and water holding capacity of the cover has to be included in water balance models.CITATION:Schneider, A, Baumgartl, T, Doley, D and Mulligan, D R, 2012. Variability in parameters of the water balance equation and their influence on evapotranspiration cover performance, in Proceedings Life-of-Mine 2012 , pp 293-300 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By James J. Cahill

Contractor's working in an urban environment face a multitude of working conditions. There is no typical "Downtown" job site. From afar we just see the skyline, or up close a specific building. This, of course, does not give us a clue as to the site conditions the foundation contractor faced in doing his work. The open, downtown building site is still available on some projects, but they are becoming rare as our cities are becoming more developed. A typical site today might include any one or several of the following problems: A. Deep pit with no ramp access B. Multi-type known or unknown obstructions C. Height limitations D. Load restrictions E. Existing adjacent building founded on shallow foundation F. Existing foundations G. Existing tunnels, utilities or subways

Jan 1, 1991

By G. C. Price

This study traces the development of the bucket-wheel excavator, points out the differences in the German- and American-type wheels, and gives the major design criteria and the advantages and disadvantages of bucket-wheel operations. A computer program, written in FORTRAN IV for use with an IBM 360 computer, simulates the operation of the digging components of a bucket-wheel excavator. By supplying certain mining dimensions, soil characteristics, and machine design specifications, this program will print out a time study of the various components of an operation, power calculations for the operation, and production data. This program, when combined with a truck, belt, or rail program, should be helpful in planning a complete mining system In material suitable for a bucket-wheel excavator operation.

Jan 1, 1973

This paper discusses how elemental analysis of conveyed bulk flows in real time using PGNAA (Prompt Gamma Neutron Activation Analysis) technology has resulted in significant improvements in advancing plant control in mineral processing operations. Basis of operation of the PGNAA through belt, full stream, continuous, multi-elemental, real time analysis technology is explained. Capabilities and limitations in plant operating environments are discussed including comparison with other real time, online technologies through review of published information available for on-conveyor minerals applications. Case studies demonstrate benefits provided by this technology in two operating mines. An iron ore company had prior experience with the PGNAA analyser technology, implementing an early model in a minerals application in 2003 to develop confidence in its measurement performance and usefulness of the data. A number of analysers were subsequently included throughout the new plant design for extensive measurement and control of conveyed bulk flows, from conveying after mining through to rail load-out. A copper-gold company installed an analyser to address copper ore blending issues where an on-belt system was the only viable option for the degree of control required. Analyser suitability was evaluated through test work on site samples to determine customised multi-element precision guarantees for each application. Analyser results from normal operation are compared against laboratory analyses of multiple cross stream samples collected from conveyed flows to assess performance. Both projects discussed were able to realise benefits previously unattainable for plant quality control, surpassing capabilities of traditional technologies which were either unsuitable for measuring conveyed flows with adequate accuracy or in real time. Equipment payback within a few months was achieved for both sites. Through proven performance in these applications, the companies consider the technology an essential component in advanced plant control necessary in new process flow sheet designs, rather than an optimisation tool.

Jan 1, 2014

? The economic health and national security of the U.S. depends on the continued availability of, and access to, reliable and affordable energy and mineral resources. However, America is hindered by a costly, inefficient and often redundant regulatory structure that thwarts domestic investment, expansion and job creation. The annual cost of federal regulations in the U.S. increased to more than $1.75 trillion in 2008; averaging $8000 per employee.(The Impact of Regulatory Costs on Small Finns, SBA, 2010) ? The complexity, uncertainty and delays within the current permitting system places the U.S. at a competitive disadvantage with many other countries that have both abundant mineral resources and a more welcoming business and regulatory climate. As a result, American and international mining companies often move overseas or across borders to invest capital, create local employment, and produce the critical minerals America must then import at higher cost, while sacrificing employment and economic stimulus. ? According to Behre Dolbear, the U.S. is ranked lowest globally due to the lengthy permitting period required before mine development can commence. (Where not to Invest, 2010).

Jan 1, 2011

By G. F. Kuncir

The analysis described herein evaluates the Bureau of Mines Program for Advancing Mining Technology - Oil Shale in terms of the economic benefits which may be derived for the Nation as a result of its successful research and development efforts. On the basis of postulated oil shale production scenarios, benefit-cost ratio indicators are computed for the program elements as they apply to surface, underground, and modified in situ oil shale mining systems. Eight value indicators are used to measure the Program's beneficial impact on the future oil shale industry in relation to planned research and development costs. These are: capital cost savings, operating cost savings, labor savings environmental quality maintenance cost reduction, reduction in production costs, byproduct production benefits, total production benefits, and additions to recoverable reserves. Program costs are aggregated from 1974 through 1987 and major benefits are accrued from 1982 through 2040. Both cost and benefit streams are discounted to mid-1975 present value.

Jan 1, 1977

By Michael L. Clar

The U.S. Bureau of Mines contracted a study to determine the feasibility of water diversion and overburden dewatering for underground coal mines in the Appalachian Region. All relevant published literature pertaining to the occurrence and control of surface and groundwater in underground coal mines was reviewed and organized into a bibliography. The impacts of mine water with respect to health and safety, production, environment, and costs were assessed. Sources of water inflow into underground mines were described. A summary description and evaluation of techniques that can be used to reduce the amount of water entering underground coal mines was prepared. A review of engineering practices currently used by operating coal mines in the Appalachian region to prevent the movement of ground and surface water into active coal workings was conducted. Major emphasis was placed on the identification of the geologic and hydrologic con¬dition of the site, onsite inspection of the methods used and an evaluation of their technical and cost effectiveness.

Jan 1, 1981

By Mandius C. Lundal

This report describes the work done to develop a coal mining machine to increase productivity and recovery from thin seams beyond the highwall, in addition to decreasing the miner's susceptibility to to highwall hazards First, radar transducers were adapted to measure coal thinkness and detect rock and coal interfaces; Then, the radar was incorporated into a cutterhead with steering controls. Next, visual displays were designed to show cutter position in the coal seam, and anticipated change in coal seam inclination, Finally, development of a telemetry system made remote control of the cutterhead possible. Simultaneously, a high-performance extended depth (HPxD) auger machine was designed with an automatic system to handle 600 ft of 36-in, diameter dual spiral flight conveyor sections. A two man crew controls all operations from a weather conditioned cab outside the VDZ, either at night or day time. As a primary mining tool, working 4000 hr/yr (2 shifts/day) recovering 60% of the coal 600 ft beyond the highwall, productlon to 500,000 ton/yr can be achieved. Volume I provides an overview of machine, systems and productivity.

Jan 1, 1977

By Brad Thrall

"Viceroy Resource Corporation of Vancouver, B.C. has recently developed the Brewery Creek Mine, an open pit heap leach gold mine 55km East of Dawson City in Yukon, Canada. Mineable reserves are 17.1 million tonnes of ore grading 1.45 grams/tonne, containing 24.8 tonnes (797000oz) of gold. Ore processing employs the heap leach technology using run of mine ore. 1996 highlights included construction of 158,000 m2 of leach pad, placing 1.9 million tonnes of ore at a grade of 1.46 gpt on to the leach pad, construction and successful commissioning of the ADR plant, and pouring of the first gold bar on November 15th.Permitting this mine has drawn significant attention because the heap leach technology, while proven in other jurisdictions, has not been used in Yukon where winter site temperatures routinely reach -45 C for extended periods.IntroductionFollowing a comprehensive governmental and public review of the proposed project, a Class A Yukon Water license was issued in August, 1995. Construction started in 1995 and leaching commenced in October 1996. The Brewery Creek Mine is in Yukon, the home of the Klondike Gold Rush nearly 100 years ago. This is the only part of Canada not glaciated in the Wisconsin advance so there is oxide ore resulting from about 80,000 years of weathering -unique in Canada. Discontinuous permafrost is present on site and has required special consideration in the design. Winter temperatures dip below minus 50 C, demanding an approach to mining and leaching that is different than in more temperate climates.Project DescriptionThe mine comprises 8 shallow, largely oxidized gold deposits along a 7km corridor. An 8 year mining program will extract 17.1 million tonnes of ore grading 1.45 grams/tonne, containing 24.8 tonnes (797,000 oz) of gold. The strip ratio will be 1.35: 1. Overall gold recovery is projected at 78%. There will be 2.3 million tonnes of ore placed on the pad annually, with an average of 2.57 tonnes (83, 000 oz) of gold recovered per year. Because of the cold winters, the mine will operate approximately 210 days per year, while the leaching process will operate on a year round basis. Run of mine ore is placed on the heap 150 days per year. The recovery process utilizes conventional sodium cyanide leaching , carbon adsorption, caustic desorption, and on-site smelting. Peak employment during mining is 145 and winter staff is reduced to 45."

Jan 1, 1997

By M. D. Lackey

The "Art" of Big Hole Drilling has been in a continual state of evolution at the Nevada Test Site since the start of underground testing in 1961. Emplacement holes for nuclear devices are still being drilled by the rotary drilling process, but almost all the hardware and systems have undergone many changes during the intervening years. The current design of bits, cutters, and other big hole drilling hardware results from contributions of manufacturers and Test Site personnel. The dual string, air lift, reverse circulation system was developed at the Test Site. Necessity was really the Mother of this invention, but this circulation system is worthy of consideration under almost any condition. Drill rigs for Big Hole drilling are usually adaptations of large Oil Well drill rigs with minor modifications required to handle the big bits and drilling assemblies. Steel remains the favorite shaft lining material, but a lot of thought is being given to concrete linings, especially precast concrete.

Jan 1, 1983

By C. J. Roos

Ground-engaging tools are used to prevent damage to the main components of earth-moving equipment. These tools consist of everything from shovel teeth to replaceable drill bits to dozer wear plates. The costs of these "consumable" items are increasing with the costs of raw materials. This project developed a tool to be used by Newmont Mining Corp. to predict the consumption of excavator teeth at a particular mine site. This paper presents the results of the Montana Tech research project in which an equation was developed to predict excavator teeth consumption based on production rates and rock properties.

Jan 1, 2010

By Robert A. Siokler

Approximately 75 percentage of the earth's land surface is comprised of shale or shale-like materials. Shale itself is composed of the residue from an almost infinite variety of weathered parent materials which have undergone deformations ranging from intense to negligible. Under standard test procedures, shales exhibit a very wide range of physical properties particularly if the test specimen is subjected to a change in moisture content, when the original test values may vary from 0 to 100 percentage. It is this wide variation in physical property values compounded by its ubiquitous presence that makes shale such a problem material to engineers. In reviewing the literature relating to shale, it is evident that the "problem" has been approached from many directions. In order to understand why shales behave as they do, investigators have sought mineralogical, geological, chemical, electrical, and physical answers. Each study yields valuable academic information, but few contribute much of value to the engineer in the field. Many valid relationships between shale strength or competency and clay type, clay content, organic content, water content, grain size, cementation, density, porosity, etc, have been established. Yet it is very difficult to extend these understandings to the in situ condition with results that can be used by the field engineer. One major reason earlier work has not produced better information lies in the ambiguity of the definition of shale. It is apparent that no one laboratory parameter can be successfully used to provide sufficient engineering information to properly describe in situ conditions. For example; shale with swelling clays will produce low strength values provided: the swelling clay is in sufficient quantity, the clay is dispersed throughout the medium involved, and there is a low value of cementation. Shales with high unconfined compressive strengths have been found with very low shear strengths. Sandy shales often provide as many ground control problems as clay shales. Shales of similar nature may provide good roof conditions in one part of a mine yet in another part of the same mine the apparently identical shale may cause substantial problems. A clear need exists to classify shale in a manner which will enable the engineer to better predict the strength and durability of shale-like materials. Studies at the University of Missouri-Rolla (UMR) have focused on finding parameters which influence durability and competency, while being discretely discernible through uncomplicated testing. Initial research concentrated on distinguishing shale8 on the basis of standard physical tests such as: unconfirmed compression, triaxial shear, and slake durability. As results accumulated, however, it became evident that moisture content played a much greater role in determining competency than had been recognized previously. As a result the focus of the research turned to developing tests which would evaluate the influence of moisture on shale behavior. The above work then became a foundation for a second phase of investigation in which a suite of standardized tests were developed to provide a classification procedure. From this study five tests were identified as being critical: Moisture Activity, Atterberg Limits, Submersion, Unconfined Compression, and Shore Hardness.

Jan 1, 1986

By Enver Alan, MerkeziYapı

People are migrating because of economic, social, natural and political reasons. These natural and humane factors effects the distribution of populations. The need for tunnels has grown in order to provide a comfortable life and reduce losses such as waste of time, labor, energy, efficiency and so on. It is inevitable to carry out excavations in rock tunnels (shears, platforms, lines, connections, wastewater, distribution, energy, transportation etc.), that will be built by excavating with conventional method, by controlled blasting regarding with constrains. In this study of applied explosives engineering the blasting applications are evaluated, which were carried out for research and development purposes at Yenisahra Station tunnels in Kartal Formation which was built with the aim of solving İstanbul's transportation problem within the framework of the Kadıköy-Kartal Metro Project. Twenty-four shots were made by using explosives in 60 blastholes that were drilled in the tunnel faces, which were located between and outside of two different faults. Six microphones were used to measure the air shock and eight geophones were used to measure the parameter values of the vibrations (particle velocity, frequency, displacement, acceleration, amplitude, wavelength etc.), which were placed at predetermined points of the surface, occurred during the blasting applications. Data from the geophone and microphones were recorded on six seismographs. The coordinates and the distances between the shot points and the measurement stations are determined by an electronic theodolite. The total number of seismic records, recorded in seismographs, is 118. The number of records of vibrations that crossed the faults is 42 and the number of records of vibrations that did not cross the fault is 76. The particle velocity, frequency, amplitude, acceleration, displacement and wavelength were measured in transverse, longitudinal and vertical directions. The total number of measurements is 354. By evaluating all seismic records, the effect of delay intervals, faults and scaled distances on the particle velocity, frequency, amplitude, displacement, acceleration, wavelength and air shock were investigated. When the vibrations formed during the Research & Development (R&D) blasts were examined, it was determined that the parameter values of vibrations that crossed the faults are lower than the ones that did not cross the faults. In addition, when the particle velocity values of all vibrations are examined according to the present circumstances, it is determined that the waves did not cross the fault in all delay intervals are superposed in all directions, and that the least superposing occurred in the 50 ms delay range.

By Lawrence Addicks

T HIS has been a most momentous year in the annals of the Institute. We have been in the midst of a situation which, were it not for the convulsions of social unrest with which life is surrounded on every side, would have attracted the attention of the world at large. I do not refer to the desperate campaign for new members. That has gone on much as usual except that, this being leap year, the annual proposal to the M. & M. Society has been omitted. Nor do I refer to the desperate situation which we found in other directions, the spread of Bolshevism, the burning of the Engineers' Club, the fact that the selling of copper appears to have become one of the lost arts. No, I speak of the great question which has to be. settled once and for all, as to whether this great Institute should adopt simplified spelling. The whole trouble started in the ranks of the California Hysterical Society. It appears, while most of the San Francisco members can read and write, several of them cannot spell. It also appears that the Secretary, in editing the Transactions, has perhaps made just a little bit too much of a point of employing the correct Stoughton idiom. At any rate, the rebels filed an amendment to the constitution, and the stage was set for civil war, with perhaps more stress on war than on civil.

Jan 1, 1920

By Fred Leonard

This report is principally concerned with the engineering and economic feasibility of area surface coal mining systems other than draglines. This analysis evaluates shovel/ trucks, shovel/crusher/conveyors, and shovel/rail excavation and haulage systems for an assortment of geologic environments and production rates in the Powder River Basin (PRB) Shovel/trucks, front-end loaders/ trucks, and shovel/crusher/conveyors were studied in a multi-seam, dipping geologic area of the Four Corners Region. The Texas lignite engineering and economic research involved bucket-wheel excavators (BWE), BWE/backhoes, and scraper/backhoe combinations for overburden and coal excavation. The PRE truck/shovel study utilized the most recent computer simulation available in both the design and cost analyses. Detailed engineering analysis, followed by in-depth operating costs (operating and depreciation) result in a complete evaluation of each mining system. Cost comparisons of the different mining systems under similar geologic and production constraints are presented in the report to illustrate the estimated capital investment and production costs per ton of coal and bank cubic yard of overburden.

Jan 1, 1980

By R. P. D. Graham

It is almost exactly two hundred years since the foundations of the mining and metallurgical industries in Canada were laid. There '."'as nothing spectacular about this early start. It had to do with the most basic phases of these industries-the mining of coal and iron ore, and the manufacture of cast and wrought iron. At several points along the coast of Cape Breton island, coal seams may be seen outcropping quite conspicuously, and it is probable that they had been observed, and possibly worked in a small way, in very early times. However that may be, these coal seams have the distinction of being the first in North America of which there is any printed record, reference to them appearing in a volume by Nicolas Denys which was published in Paris in 1672. Regular coal mining in the district did not commence until about fifty years later, however. The metallurgists started their operations along the north shore of the St. Lawrence river. Here, at many points between Montreal and Quebec, are to be found deposits of bog iron ore, and in 1 730 a furnace for smelting such ore was established on the St. Maurice river. The St. Maurice forges continued in operation until 1880, and throughout that long period they were famed for the fine quality of castings produced, and also for a-superior wrought iron.

Jan 1, 1924

By R. J. Latino

Because of the lack of a universally accepted definition or standard for RCA, we are left to our own conventions in the marketplace as to what is most ?effective? or a ?Best Practice? for our own facilities or organization. This lack of uniformity in the application of RCA produces an equal lack of uniformity in the measureable outcomes of RCA on the bottom-line from site to site and industry to industry. What is the definition of success for an RCA? Is it regulatory compliance? Is it some quantifiable measure of bottom-line performance? Is compliance and bottom-line performance the same thing? Can we measure the ROI we receive by doing compliant RCA? These questions must be adequately addressed if any definition of RCA is to be effective on the bottom-line. Like our various Corporate Vision and Mission Statements, what would be our Vision and Mission for RCA? When pondering the answer to this question, we should consider: ? What Key Performance Indicators will the Success of RCA be Linked to? This provides a direct correlation to the corporate dashboard and therefore garners support for the RCA effort when implemented at the sharp end. Not until we know what KPI?s will effectively measure our maintenance and reliability objectives can we begin to establish which opportunities will afford the greatest returns1. ? What Bottom-Line Metrics will be Tracked to Measure the Effectiveness of Our RCA Effort? Will it be increased production, profitability, regulatory compliance, etc.? Will it be decreased injuries/fatalities, claims, customer complaints, risks, etc.? We should be specific about these metrics and their correlation to the metrics on our corporate dashboard. ? What Will Trigger an RCA Investigation? Normally companies will establish quantifiable thresholds to be surpassed before an RCA will be conducted. Examples may be an OSHA recordable injury, a failure event in which production losses exceed $250,000, an equipment failure in excess of $50,000 or a regulatory violation. This is the norm. However, we should realize this is using our RCA skills totally on a reactive basis. High Reliability Organizations (HRO) strive for proaction and they also use RCA proactively. Why can?t we use RCA to analyze why unacceptable risks from an FMEA are so high? It is perfectly applicable yet rarely implemented in this fashion.

Feb 27, 2013

TowerMill - Advantages in Wet Grinding Applications The TowerMill, which has now been in existence for no less than 50 years, is one alternative to the horizontal ball mill and offers several advantages. The TowerMill is widely used in (coal-fired) electric power plants for the grinding of raw material for the FGD (Flue Gas Desulphurisation) process involving very high throughputs, very fine product sizes and high availability. Some companies in the mining industry also looked at the use of such optimised grinding machines several years ago and found that many of the advantages offered in other industries are transferable to new applications. Much development work has been undertaken to improve the TowerMill for new applications and, as part of that work, tests have also been conducted to make direct comparisons of their performance with that of ball mills. Grinding tests were performed using the same raw materials and comparable machine sizes. Some of the results are discussed in this paper, along with a comparison of the advantages and disadvantages. The conclusion provides an outlook for some worthwhile future applications. The test results, which are described and analysed, show that the TowerMill offers significant advantages in relation to operating costs and operational safety. An example based on the wet grinding of limestone is presented.

Sep 13, 2010

By R. C. Earlougher

Jan 1, 1970