Search Documents

Thermodynamics and kinetics? of the removal of Va elements (As,Sb,Bi) from copper were investigated 1n the fire relining by alkaline carbonate fluxes such as Li 2co3 , Na 2CO3 and K2CO3. The distribution coefficients of As, Sb and Bl between alkaline carbonate fluxes and mo) ten copper were ?obtained at 1200°C under the different oxygen potentials. As and Sb were easily removed from copper to fluxes as pentavalent oxide form. On the other hand, Bi was hardly removed except by a Ll2CO3 flux. The removal rates of Va elements from copper were also measured In the temperature range of 1150°C.- 1250°C. The removal rates of As and Sb were much higher than that of Bi. The removal rates of Va elements showed the same order of the distribution coefficients. The removal rate could be expressed by following equation. (1).

Jan 1, 1987

By Jian Li, Guo Chen, Bingguo Liu, Hongying Xia, Jinhui Peng, Libo Zhang

"Decomposition of ammonium tetramolybdate to prepare Mo03 using silicon carbide crucible in microwave fields was investigated. The results were analyzed Using TG-DTG and X-ray diffraction. Meanwhile, the effects of heating rat, material thickness, socking time, socking temperature on the structure of preparing Mo03 were studied. TG-DTG curves show that the decomposition process of ammonium tetramolybdate is only one stage, in the temperature range 300-350°C, whose begin to decompose when temperature increases beyond 300°C. The molybdenum trioxide was prepared by thermal decomposition. The quality ofMo03 was not affected under the heating rat is 12°C/min. It was beneficial for decomposition ratio with the lower material thickness, longer soaking time, and higher soaking temperature. XRD curves showed that it is viable method for preparation of Mo03 by decomposition from ammonium tetramolybdate in microwave fields.IntroductionMolybdenum is widely used in national defense, aviation, industrial and agricultural production as rare refractory metal. Molybdenum trioxide is vital raw materials for the process of preparation of molybdenum. The traditional production technology of molybdenum oxide is that ammonium tetramolybdate is calcined in rotary kiln or 4-tube furnace [J,2J. But the longer production time, the higher production cost, the lower furnace thermal efficiency, and bigger the energy consumption, especially the powder is easy to leak, the working environment is poor by using rotary kiln [ 3 l _ The particle of molybdenum oxide is non-uniform by using 4-tube furnace because of the uneven temperature of every tube and the poor exhaust of boat bottom [4l _ However microwave heating is quick and uniformity, it is a meaningful research that the microwave is used in the process of calcining ammonium tetramolybdate."

Jan 1, 2013

By Matthew Jeffrey

Due to the increasing environmental and public concerns over cyanidation, there has been a large amount of research into viable alternative lixiviants. Despite these studies, there is little published data directly comparing the kinetics of gold leaching for each of these alternatives: most of the literature is concerned with gold extraction from ores. This paper presents a detailed kinetic study of gold leaching in cyanide, armmonia/thiosulfate and chloride/hypochlorite solutions. The gold leach rates were measured using a rotating electrochemical quartz crystal microbalance (REQCM). This instrument allows the mass of a gold sample to measured in?situ, with a sensitivity of less than 10 ng. From the results of these studies, it is possible to select experimental conditions where the leach rates of the alternative lixiviants are similar to that for the traditional cyanide system.

Jan 1, 1998

MODELLING FOR DESIGN AND CONTROL AT KALGOORLIE NICKEL SMELTER Modelling at KNS has been driven by a need to have better tools to answer questions about control, design and optimisation of the plant. This paper describes a number of modelling tools developed for use at KNS and how the development of modelling tools fits with a design and control strategy. In the area of control, a thermodynamic model has been developed to allow process parameters to be calculated. The model allows for the automatic selection of data from a laboratory data base, desired operating set points are input and the operating parameters are calculated. The model has the ability to adjust the burner efficiency and the furnace heat loss depending upon conditions. To assist with the testing of proposed furnace design changes, various mathematical models of the burner and shaft have been created using PHOENICS. These models are particularly well suited to combustion heat transfer and flow aspects of both the burners and shaft. Validation of these models have been based on novel sampling and measuring techniques in the shaft and also by using scale and cold models. Overall plant energy and cost structures can be analysed using a flowsheet simulation, developed to evaluate potential alterations to the plant flowsheet. This model system allows the global evaluation of process changes.

Jan 1, 1993

By Donna L. Bodine

The ability of oxidized Upper Freeport bituminous coal to adsorb Cu2+, Cd2+ and Mn(VII) from very dilute aqueous solutions has been studied. Low-rank coal is known to adsorb heavy metal ions from dilute, aqueous solutions, probably by ion exchange and/or chelation by acidic functional groups on the coal surface. However, it would be advantageous to use higher rank coals for water treatment. Coal samples were oxidized thermally or by 30% H202 to increase the surface concentration of phenolic and carboxylic groups, then portions were shaken with Cu2+ and Cd2+ solutions. Acidic KMnO4 was also used to oxidize coal, with concurrent sorption of the resulting Mn(IV) and Mn(ll). The effect of oxidation treatment, metal ion concentration, and solution pH on metal uptake kinetics was investigated. Potential applications for treating effluents, especially those containing oxidizing ions, are discussed, along with possible flowsheet options.

Jan 1, 1995

By M. Neises, M. Roeb, C. Sattler, S. Stenger

"A two-step thermo-chemical cycle process has been developed and investigated. It is based on metal oxide redox pair systems, which can split carbon dioxide as well as water molecules by extracting oxygen atoms and reversibly incorporating them into their lattice. If concentrated solar radiation is used as the heat source, a promising method exists to produce synthesis gas from water and CO2. An easy way of operation is gained by the combination of a ceramic substrate as the absorber structure, which can be heated to high temperatures with concentrated solar radiation, and of a metal oxide coating which is capable to carry out the redox reactions. The performance and kinetics of a ferrite based redox material coated on ceramic substrates were investigated in a laboratory set-up. CO2 could be reduced with significant conversions. In addition, several side reactions were observed like the formation of carbon and like the Boudouard reaction.IntroductionThe search for alternative energy carriers and for processes able to reuse carbon dioxide stimulates the research for sustainable routes of alternative fuel production. In the scope of this search thermo-chemical processes combined with sources of concentrated solar energy have become more and more attractive. Ideally, the only raw materials for such processes are water (H2O) and carbon dioxide (CO2) enabling not only a process free of emissions, but also allow to reduce emissions of other processes by reusing CO2 to provide synthesis gas, which itself can be applied to produce chemical commodities or even better synthetic fuels like methanol or petrol.In contrast to the direct splitting of those raw materials, thermochemical cycles split water and CO2 in several steps and enable hydrogen (H2) and carbon monoxide (CO) generation at temperatures controllable by today’s technical equipment. One of the most interesting thermochemical cycles is a two-step process using metal oxide based redox systems. During the first step of this cycle (the regeneration step) the metal oxide is reduced setting some of its lattice oxygen free according to reaction (1). In the next step (the splitting) the reduced and activated material is oxidised by withdrawing oxygen from water and CO2 and at the same time hydrogen and CO is set free according to reactions (2a) and (2b) respectively."

Jan 1, 2011

By J. J. Rush

Neutron scattering and analysis techniques are extremely powerful, often unique, probes for the characterization of the amount, location, bonding states, and dynamics of hydrogen in all classes of materials. Developments over the past decade at the NIST Center for Neutron Research and elsewhere have greatly increased the sensitivity and dynamic range of neutron methods. In this paper, we provide a flavor of the capabilities of modem neutron instrumentation for the study of hydrogen in a number of technologically interesting systems, including metal hydrides, fuel-cell materials, fullerenes, and disordered carbons.

Jan 1, 2002

By Antti Roine

HSC Chemistry is a widely-used therniochemical tool in the chemical and metallurgical industries and in universities. The main reasons for it's popularity is the easy user interface and the large integrated thermochemical database. This paper summarizes the main properties of the new HSC Chemistry version 3.0, and gives a short review of the new features: Some metallurgical applications with the new features are also presented. HSC Chemistry 3:0 contains seven calculation modules and a thermochemical database with more than 11 ,000 chemical compounds. The new spreadsheet type table editor gives more control to the user, the new graphics routines have fewer limitations and more formatting properties. The capability and speed of calculation routines have also been improved.

Jan 1, 1998

By Jose M. Gomez-Vega, Osamu Takai, Atsushi Hozumi, Hiroyuki Sugimura

"Ongoing research is reported aimed at improving the properties of mesoporous silica-based coatings on various substrates for optoelectronic or medical applications. Tetraethylorthosilicate (TEOS) was selected as the silica precursor, and amphiphilic triblock copolymers poly( ethylene oxide)- poly(propylene oxide)poly( ethylene oxide) as the surfactant micellar template or structure-directing agents. Cetyltrimethylammonium chloride (CTAC) was also used as a control agent. The effect of the templating agent and type of substrate (glass, Si, and Ti) on the mesoporosity, particularly on the alignment of the mesochannels, has been investigated. Three · different treatments (thermocalcination, photocalcination, and solvent extraction) have been also studied to remove the organic templates.IntroductionThe fabrication of mesoporous silicate-based materials through the utilization of a sol-gel process, where cooperative organization of organic and inorganic species takes place, provides a versatile approach to nanoscaled structures with potential applications in fields such as catalysts, optoelectronics, biomaterials, etc. Compared to conventional low molecular weight surfactants, self assembly of amphiphilic·block copolymers can result in mesostructured materials with larger pore sizes (up to 30 nm).1 Most of the synthetic strategies use silicon alkoxides as the silica precursor, although non-silicate metal alkoxides, e.g; Ti, Zr, Al, and B, have been also used to obtain different mesoporous materials, or even mixed metallic oxide systems. 2 Recently, Yang et al. 3 • 4 were able to synthesii:e a great variety of mesoporous metal oxides ID nonaqueous media using inorganic precursors (metal chlorides) and block copolymers as structure-directing agents."

Jan 1, 2000

By Zhang Duomo

A novel homogenous precipitation method, including microwave heating, solution conductivity controlling and freeze drying, was developed for the preparation of US nanoparticles. The effects of the precipitation conditions on the structure and morphology of CdS particles were discussed individually. It was found that under the experimental conditions the particle sizes were controllable in the range of 14nm to 100nm. Blend-type CdS was obtained from nitrate or sulphate solution and the more stable wurtzite-type US was obtained from chloride solution, which was ascribed to the coordination of C1 and Cd2+ altering the supersaturation of the solution as well as the different growth units and their connecting patterns, In the precipitation process the surface of US nanoparticles were surface modified with CH3CHSCOOH. The results demonstrate that the bifunctional thiols of thioglycolic acid modified the surface through Cd-S coordination bonding and the induced counter ion AOT-SO3 as the balance charge further increased the stability and dispersity of US nanoparticles. This surface-modified US nanoparticles had been used to prepare nonlinear optics and self-assemble catalysts.

Jan 1, 2003

By C. Zografidis, K. Karalis, E. Devlin, S. Tabouris

"The main parameters affecting energy and electrode consumption in smelting reduction of Greek nickeliferous laterites in submerged arc electric furnaces (E/F) were investigated. Within this framework, the operational data of E/Fs, such as energy consumption indicators, electrode consumption indicators and chemical characteristics of Fe-Ni and slag, were correlated with the physicochemical characteristics of the calcine, produced by roasting reduction of laterite in rotary kilns (R/Ks), such as reduction degree, temperature, chemical composition and granulometry. The results obtained provide a significant input for further research on the modelling of the roasting reduction – smelting reduction process, which is a critical tool for energy optimization.IntroductionThe two main steps of pyrometallurgical treatment of greek nickeliferous laterites for ferronickel production include: i) drying, pre-heating and controlled pre–reduction of laterite ores with solid fuel reducing agents and fuel oil in rotary kilns (R/Ks) for the production of a calcine, and ii) smelting reduction of the calcine in open-bath submerged-arc electric furnaces (E/Fs) for the production of Fe-Ni alloy with 12-16% Ni [1].The energy absorbed from the endothermic reductive reactions of iron, nickel and cobalt oxides (Fe2O3, FeO, NiO and CoO) of the calcine with the remaining carbon in the E/Fs, corresponds to about 16% of the total energy output in the smelting reduction step [1]. This is indicative of the significance of the calcine’s reduction degree for the electric energy requirements in the E/Fs. Moreover, the chemical characteristics and the granulometry of the calcine constitute critical parameters for the energy requirements as well as the smooth operation of the E/Fs."

Jan 1, 2012

By P. J. Uggowitzer, K. Steinhoff, A. Wolf

"With the increasing acceptance of the Thixoforging process in the last few years, also the technical and commercial requirements for this forming technology and its components increased. So far, a great deal of work has been done in the development of an efficient process and control design. However, less attention has been paid to the development of new specifically tailored aluminum wrought alloys for this specific manufacturing process. · In this paper a new AlMgSi-alloy (A6082), optimized for the Thixoforging process, is presented. In the first part, the technical potential of the new alloy is specified by its microstructural evolution and flow characteristics in the semi-solid state. In the second part, the mechanical properties of thixoforged components of different conventional AlMgSi-alloys a (e illustrated · and compared to the new alloy.IntroductionSemi-solid metalworking, also known as semi-solid forming, is a hybrid manufacturing method that incorporates elements of both casting and forging. The key to the process relies on the peculiar flow behavior of slurries containing non-dendritic solid, which was first studied at the MIT by Flemings et al. [i], in the early 1970s. It was discovered, that if an alloy is uniformly stirred during freezing, discrete rounded particles of solid are formed rather than the normal dendrites, and the slurry is highly fluid (-5 Pas) up at least 50% solid. In addition, these slurries posses thixotropic flow characteristics: the viscosity is dependent on sheare rate and time. The more vigorously they are stirred, the more fluid they become. However, on standing the viscosity recovers and the material stiffens (-106 Pas).The semi-solid forming process exploits this phenomenon. In a first step, the required non-dentritical- microstructure is obtained by mechanical or electromagnetic stirring during primary solidification of the alloy. The stirred slurry is generally fully solidified as a feedstock billet and - in a second process step - reheated above the solidus temperature into the semi-solid state. In this condition, the thixotropic properties permit the material to be handled by robotic devices and transferred to a die (Thixocasting) or subjected to- a forming process by means of forging (Thixoforging). Owing to the shear stress which acts on the semisolid material during forming operation, the viscosity of the material is reduced attaining so the desired fluid-like flow characteristics."

Jan 1, 2000

By Xiang Sun

Microwave processing has been under continuous development as an advanced heating method in modern industries. However, problems with uneven heating still remain. Although heating uniformity is highly dependant on the properties of the materials being heated, proper furnace design to prevent uneven field distribution is another important factor. As an alternative to experimental measurements and adjustments to find appropriate furnace parameters, computer simulation is a convenient method for modeling, understanding, and improving the uniformity of microwave heating. This paper discusses current modeling technologies as well as applicable techniques for improving microwave heating uniformity. The purpose is to give a basic understanding on how to find, analyze, and minimize the problems associated with uneven heating in microwave processing.

Jan 1, 2006

By Liyuan Chai, Bing Peng, Ji Peng, Di Yu

"Electric arc furnace (EAF) stainless steel dust has been classified as a hazardous waste by various government regulatory agencies as it releases heavy metals to environment. The solidification of EAF dust is to stabilize the hazardous components to the amorphous silica-alumina-based clays. The process of solidification is investigated and the softening temperatures of dust and additive clay mixtures are measured for economical thermal treatment. The results indicate that the mixture of dust and local clay with the ratio of 1:1 has the lowest softening temperature 1100 °C and it could pass the toxicity characteristics leaching procedure (TCLP) test for the environmental regulatory limits after thermally treated at softening temperature for 15 min. Major phases of thermal solidification product clinker are CaAl2Si2O8, (Fe, Cr)2O3, (Fe, Mg)(Cr, Al)2O4 and Al6Si2O13.IntroductionThe yield of stainless steels in China arrived to 10 million tons in 2006 and more than 0.2 million tons of stainless steel dust are produced annually. Approximately 1-2 wt.% of scrap charged to an electric arc furnace (EAF) enters the off-gases and then is converted into the dust and reported to the bag-house. The disposal or landfill of the dust becomes a serious environmental problem in China due to the increased production of stainless steels in recent years. The dust contains elements such as chromium (Cr), nickel (Ni), lead (Pb), zinc (Zn), cadmium (Cd) and their solubility in leaching media exceeds the environmental regulatory limits [1]. Even though easily feasible for low-grade MgO, it is not appropriate to stabilize the heavy metals from the heavily contaminated soils after the dust landfill [2]. Several dust treatment technologies have been developed and they can be divided into two types. One is to recover the metals from the dust [3, 4] and another is to stabilize hazardous components present in the dust [5, 6]. Recycling of the dust generated in EAF is a remediation option for cleaner production. Direct recycling of EAF stainless steel dust was developed to recover the metal value from the dust and protect the environment [7], but it was only suitable for the dust with high contents of Ni, Cr and Fe. As for the dust with low valuable metal content, thermal solidification is an appropriate choice for the dust treatment."

Jan 1, 2012

By Qian Xu, Guangshi Li, Xionggang Lu, Xingli Zou, Hongwei Cheng, Cong Xu, Changyuan Lu

The roasting of nickel-bearing sulfides is a complex but important process which has not been adequately characterized. Combination of X-ray diffraction and scanning electron microscopy has been proved to be useful for such experiments. The leaching results of nickel, copper, iron and cobalt was analyzed by ICP methods. Process possibility of polymetallic sulfide concentrates through a three-step procedure (oxidation roasting - chlorination - water leaching) was suggested. Ammonium chloride could react with nickel/copper oxides to produce intermediate complexes. At the temperature range of 280~340 oC, these complexes further decomposed to the corresponding simple chlorides. Roasting sulfide concentrate using NH4Cl is effective for complex ores.

Jan 1, 2016

By Kazuyoshi Shimakage, Shinji Hirai, Kenji Wada

"An amorphous zirconium oxide coating was prepared by the sol-gel process using zirconium tetra-n-butoxide on the surface of aluminum to improve the corrosion resistance to salt, acid and alkaline attacks. The coating films formed on the smooth aluminum substrates under UV-irradiation indicated an excellent corrosion resistance for salt, acid and alkaline attack tests. For example, the corroded area of coating film in salt attack test for 3600ks in the order of sol-gel coating· film< chromate film <boehmite film, and the sol-gel coating film had the best corrosion resistance. The coating film prepared on the coarse aluminum substrate by a boiling treatment after heat treatment at 573K also had greater corrosion resistance, and a water-avid surface appeared a contact angle of approximately 3°.IntroductionAs given in a previous paper1; a composite film consisting of a porous layer of anodically grown aluminum oxide filled with amorphous zirconium oxide and an amorphous zirconium oxide coating layer deposited thereon via the sol-gel process utilizing the dip-coating technique, was prepared to improve the alkaline corrosion resistance of aluminum. The alkaline corrosion resistance of these composite films was increased in the range of 24 to 50 times those of conventional anodic oxide films anodized in sulfuric acid. As a result, it was proved that heat treatment at 573K after dip-coating was an important process to .remove organic component from gel film and to accelerate the densification of coating layer. Furthermore, the effect of ultraviolet (UV) irradiation at ambient temperature on the densification of coating layer was also examined to lower the heat-treatment temperature2.Then, a sol-gel film prepared by UV irradiation at ambient temperature indicated that alkaline corrosion resistance of aluminum was superior in the range of 2.4 times to 2. 6 times that of the conventional composite film heated at 573K."

Jan 1, 2000

By Kenneth P. Michalek, James E. Kelly, Jonathan A. Dantzig

"Many investigations have been reported regarding the simulation of continuous casting with emphasis on in-mold heat transfer. These analyses have been limited, however, because they require either estimation or measurement of the characteristic heat transfer between the ingot and the mold. In this paper, a self-consistent model 'is presented for calculating the heat transfer between a solidifying continuous casting and the mold, in the context of the continuous casting of steel. Using both thermal and stress analyses, the air gap formed during continuous casting is calculated and used to compute the heat transfer coefficients. Iteration between the thermal and stress analyses is used to determine a self-consistent solution. IntroductionThe continuous casting process for steel is illustrated schematically in Fig. 1. Molten steel is tapped into a tundish from which it flows at a controlled rate into the continuous casting mold. The initial shell of the casting forms in the mold by transfer of heat from the metal through the mold wall to the cooling water. The remainder of the casting is solidified by application of water sprays, and/or radiation cooling below the mold.Heat transfer in the mold portion of the process is important because it controls the formation of various defects which are deleterious to subsequent processing. Examples of defects formed in this region are surface irregularities, such as cold folding and oscillation marks, and more serious defects, such as longitudinal or transverse cracks. A more catastrophic problem which may occur is a breakout, in which the shell ruptures and molten steel is discharged in an uncontrolled way."

Jan 1, 1986

By J. F. White

An experimental study was undertaken to evaluate the feasibility of a selective chloridizing roasting pre?treatment process for the elimination of impurities from zinc feed?stocks prior to recovering zinc by conventional unit operations. In this investigation, a number of chemistries that might serve as a basis for such a pre? treatment process were examined. A variety of chloridizing agents were admixed with EAF dust to promote the selective removal of lead and cadmium by the formation of volatile metal chlorides, he results of the experimentation firmly establish that selective chloridizing roasting is a technically feasible means of eliminating lead and cadmium from EAF dust. Excellent extraction efficiencies were accomplished with a number of chloride additives; as high as 98 percent lead extraction and 88 percent cadmium extraction were attained with minimal zinc losses, Continuous pilot?scale tests reinforced the trends established by laboratory?scale experimentation, Attempts of chlorine elimination using pyrohydrolysis were less successful. The extent of chlorine elimination was found to be highly dependent upon EAF dust sample type and treatment temperature.

Jan 1, 1996

By Ravi Vancheeswaran

The consolidation of ceramic fiber reinforced metal matrix composites is a key process step in the synthesis of high performance composite systems. A simulation tool has recently been developed for predicting the evolution of the composites internal state microstructural variables (eg. relative density, fiber microbendinglfracture, and chemical reaction layer thickness at the fiber-matrix interface) during the consolidation processing of spray deposited composite mono-tapes. A Generalized Predictive Control (GPC) scheme is used in conjunction with the simula-tion tool to design near optimal process paths that minimize fiber damage and reaction product thickness while simultaneously maximizing the composites relative density. The microstruc-tural evolution depends nonlinearly on the process conditions and therefore the scheme uses a constantly updated linearization of the model to optimize the input process variable vector. A control simulation is presented to illustrate the performance of the design scheme and to assess the feasibility of its use for the achievement of goal state microstructures at the completion of consolidation cycles.

Jan 1, 1996

The standard procedure of fire refining consists of sulphur removal via air injected through tuyeres, arsenic slagging via soda-lime flux and oxygen reduction by air or oxygen deficient air or a steam fuel mixtures. The use of porous plugs to stir with an inert gas has been mainly considered as a surface renewing agent that increases the product quality and shorten the refining cycle. In the present study the effect of the bottom stirring by nitrogen gas injection through porous plugs for the treatment of the crude copper in the range of 400-150 ppm sulphur, 3,000-2,000 ppm arsenic and 14,000-7,000 ppm oxygen content was investigated. The combined effect stirring-reducing, by the use of air or a steam fuel mixtures through tuyeres for oxygen removal, follows a kinetics of first order where the constant, K, can be represented by the following polynomial expression: K = A * R2 + B * R + C Where A, Band C are constants that depend on the nitrogen flow rate and R is the air-fuel ratio or the steam-fuel used in the reducing step. Depending on the optimization of the flow of nitrogen and the air-fuel or steam-fuel mixture and only if just the oxidation, complexing and reducing steps are considered, the process cycle might be shortened by 45%.

Jan 1, 2003