Search Documents

By E. V. Redin

"The Bakal (South Ural, Russia) deposit of iron ore bearing iron carbonate (siderite) with the capacity of more than 1 billion tones belongs to the MMK. This ore cannot be fully processed via blast furnace technology because of high content of MgO. According to the investigations carried out in the USA and Japan in 1999-2004 the ITmk3 (Ironmaking Technology mark three) RHF technology is a breakthrough in Ironmaking. Four iron ore types (hematite, magnetite, high and low Al2O3/SiO2) were tested. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from iron carbonate bearing ore via the ITmk3 by means of the lab scale testing. Green pellets were processed via a lab tube (chamber) furnace to simulate RHF conditions. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.IntroductionThe ITmk3 process upon which this paper focuses was developed by Kobe Steel in its research facilities in 1996 [1]. After pilot testing at Kobe Steel’s Kakogava Works in 1999-2004 the pilot demonstration plant was built and operations were successfully carried out by Mesabi Nugget joint venture in 2002-2004. Steel Dynamics has committed to building the commercial plant at the Mesabi Nugget site in Hoyt Lakes (Minnesota). Only 4 iron ore types (hematite, magnetite, high Al2O3/SiO2 and low Al2O3/SiO2), as well as 4 coal types with range of volatility, ash and fixed carbon were tested. Results were consistent with nugget characteristics confirming ITmk3’s flexibility with respect to raw material inputs. At the same time, no research in the field of nugget from iron carbonate bearing ore with high content of MgO has been done. Such kind of iron ore is restricted for charging into the blast furnace due to contamination of MgO. The reason for restriction is the limitation of load of MgO in the blast furnace. If a lot of MgO enters the blast furnace, slag becomes viscous. The viscous slag is obstacle for stable operation of the blast furnace."

Jan 1, 2012

By Bryce Clark

An outline of the current world's known sources and resources of cobalt, looking at both land and possible undersea deposits, is given as a prelude to an examination of current and historical actual world production on geographic/company basis. These production figures will be compared to apparent consumption by segments, both geopraghically and end-use based. Consumption of cobalt has been regarded as price sensitive and a historical look at prices against all other figures will be considered. Included in this scenario will be a brief overview of cobalt's uses and a comment on future trends. Tables will include: Resources, Production, Consumption, Prices, Markets.

Jan 1, 1993

By Riqing Ye

Laser Engineered Net-shaping (LENS TM) is an emerging manufacturing technique that ensures significant reduction of process time between initial design and final components. The fabrication of fully dense parts with appropriate properties using LENS TM process requires an in-depth understanding of the entire thermal behavior of process. In this paper, the thermal behavior during LENSTM processing of 316 stainless steel was studied both numerically and experimentally. Temperature distribution and gradient in the fabricated 316 stainless steel part were obtained by Finite Element Method (FEM) simulation. The numerical results are in good agreement with the experimental observations. The numerical method may be used to optirnize process parameters and predict the thermal response of LENSTM fabricated components. Key words: Laser Engineered Net-shaping, Thermal Behavior, Finite Element Analysis

Jan 1, 2003

By Kazuki Morita

A new route to produce solar grade silicon (SOG-Si 6N) from metallurgical grade (MG-Si 98%) has been developed in Japan, which may satisfy the increasing demand for solar cells in the near future. Since some elements such as P and B have very large segregation coefficients, solidification refining is not effective for their removal and costly processes, such as electron beam vacuum melting and oxidation plasma refining, are required. According to our previous results which showed the effectiveness of leaching procedure with Ca addition for Fe and Ti removal, possibility of P and B removal by acid leaching was focused expecting that their affinities for Ca in molten silicon might be considerable. Hence, the effects of Ca addition on the thennodynamic properties of P and B in molten silicon alloys have been investigated for overall control and optimization of the SOG-Si production process in the present study. The interaction parameters between Ca and P, and Ca and B were determined by chemical equilibration techniques at 1723 K. Although the interaction parameter between Ca and B was slightly negative, that between Ca and P showed a large negative value. Also, the results for the leaching test with various amount of Ca addition revealed that the removal fractions of both elements, especially P, drastically increased with increase in the Ca content, which showed very good agreement with the prediction from the interaction parameters derived in the present work. The present results suggest that the preliminary leaching procedure can reduce the processing time and energy for SOG-Si refining. Keywords: Silicon, Solar Cell, Refining, Acid Leaching, Thennodynamics. Interaction, Phosphorus, Boron, Calcium

Jan 1, 2003

By Sadegh Safarzadeh, Anne-Marie Suriano, Stanley Howard

The electrodeposition of metal ions from aqueous electrolyte solutions has been a well-known process for the last half century. With numerous industrial applications such as electroplating, electrowinning and electrorefining, the kinetics of electrochemical reactions involved in the process has been extensively researched. Arrhenius-type rate equations, the Butler-Volmer equation, and the empirical Tafel equation are among the most important models to explain the rate of electrochemical reactions. The study of the kinetics of metal deposition is critical to understanding the underlying mechanisms through which a certain morphology of metal deposit is formed on the cathode. The purpose of this paper is to elucidate the influence of experimental parameters such as pH and additives on the rate and the reaction mechanism determining the rate limiting step of the electrodeposition reactions.

Jan 1, 2015

By Vadym Drozd, Yongzhou Sun, Shah Najiba, Jiuhua Chen, Andriy Durygin

"Phase transitions of the potential hydrogen storage compound, ammonia borane (NH3.BH3), was investigated using Raman spectroscopy and a diamond anvil cell at high pressures up to 9.5 GPa and low temperatures down to 90K. At room temperature, ammonia borane has three phase transitions in this pressure range. Upon cooling, four new phases were discovered through changes in characteristic Raman spectra. This result provides information about the stability of new bonding characteristics of this potential hydrogen storage material at low temperature and high pressure region.IntroductionDevelopment of hydrogen technology requires the safe, efficient and environmental friendly materials for hydrogen storage and hydrides have attracted much attention as hydrogen storage media. Among chemical hydrides, ammonia borane (BH3NH3) stands out due to its high gravimetric and volumetric hydrogen density ' "". Despite high hydrogen content, this compound is very stable. It releases hydrogen in several steps by thermal decomposition in the temperature range of 100°C to 500°C. Direct thermal decomposition also causes toxic borazine emission. Recent research interests on ammonia borane include destabilizing this compound to lower the dehydrogenation temperature with an enhanced hydrogen release rate using different techniques, e.g. the nanoscaffolds'', ionic liquids"" and acid'"" or transition metal catalysts' ""'. As a molecule of ammonia borane consists of protonic (NH) and hydritic (BH) hydrogens bonded by the polarized dative bond, thermal or catalyzed decomposition requires breaking of N-H and B-H bonding. Still now, the detailed information about the bonding characteristics of ammonia borane is not sufficient to understand details about its phases and structures. The development of methods to enhance hydrogen discharge rate from ammonia borane requires a detailed study about the structural and dynamical properties that control the stability and the intermolecular interactions of this material. This study is motivated to investigate the stability of the existing phases and also to explore the existence of any new phases at different temperatures and pressures which may have enhanced hydrogen release and uptake properties."

Jan 1, 2012

By Lei Wang, Jianjun Wang, Lingen Luo, Zhengbang Li

Dearsenication in molten steel was studied by adding Ca-Fe Alloy-based arsenic removal agent. In order to improve the utilization rate of Calcium Iron Alloy and improve arsenic removal ratio, [O] is less than 0.0005% and [S] is less than 0.0035%, Al is added into the molten steel. In the processes of adding CaO-Al2O3 based alkalinity slag for arsenic removing in molten steel (initial arsenic content is 0.0080%), arsenic removal ratio reaches 50% when Ca-Fe Alloy addition amount is 18%. During the arsenic removal experiment, adding Rare Earth promotes the arsenic removal reaction and makes the arsenic removal more effectively.

Jan 1, 2015

By Geoffrey A. Brooks, M Akbar Rhamdhani, Md Saiful Islam

A novel electrically-enhanced metal purification using slag has been developed. This was achieved by applying DC potential between liquid metal and slag phases. The concept was demonstrated through small-scale experiments at temperatures of 1500-1600oC for the removal of boron from Si-B melt using CaO-SiO2-16wt%Al2O3. Silicon (containing B) and slag were reacted in an alumina crucible in a resistance tube furnace. A circuit was produced by immersing graphite rods into the silicon bath and the slag layer. Electrical potential differences of up to 3.5 V were applied during the reactions. The reaction rates, the opencircuit voltages and short-circuit currents (in the case when the potential was applied) were then measured and determined for various slag to silicon ratio. It has been shown from this study that both the apparent rate and the boron partition ratio were increased by a factor of approximately 1.6.

Jan 1, 2014

By D. Lambert

Process modeling for large deformation metal forming processes has been developed into a very successful tool in commercial applications during the last two decades. DEFOR.MTM is a well-known metal forming process simulation program used by many industrial and research institutions. Recent developments include the ability to model multiple deforming body behavior during multi-pass pack rolling and microstructure prediction during multi-pass shape rolling. This paper summarizes how DEFOR.MTM can be applied to a number of rolling processes and briefly describes preliminary work carried out using the ALE technique. Keywords: Simulation, Rolling, Pack, Shape, Microstructure, FEM, ALE, Tantalum

Jan 1, 2003

By Masao Miyake, Eiichiro Matsubara, Tetsuji Hirato, Yasuhiro Awakura

"Zn-Cr alloy coating with around 15 wt% Cr has been found to have much higher chemical corrosion-resistance to steel than conventional zinc plating, while· its structure has not been clarified. The Zn-Cr alloy plating is performed at high current densities around 1 A cm-2 and for 10 to 20 sec using acidic aqueous sulfate solutions with some additives in the iron-steel industry. Due to the high current densities, it seems reasonable to consider that the Zn-Cr alloy plating proceeds under an unsteady-state condition and that the resulting coatings have a non-equilibrium phase and have a structure change in the .direction of thickness. In this research, the crystal structure of the Zn-Cr alloy coating electrodeposited at high current densities and change of the structure in the direction of thickness were examined by X-ray diffraction. The coatings containing under 20 and 35-40 wt% Cr had hcp and bee structure, respectively, while the coatings containing 20-35 wt% Cr comprised two phases with the hcp and the bee structure. The structure of the coating varied in the direction of thickness; both the hcp and bcc phases coexisted in the vicinity of the substrate, while the hcp phase became predominant with increasing distance from the substrate.IntroductionRecently it has been reported that Zn-Cr alloy coating containing around 15 wt% Cr has much higher corrosion-resistance to steel than conventional zinc plating.1-3) The corrosion-resistanc·e of Zn-Cr alloy plated steel sheet with a plating amount of 20 g m·2 is, for example, superior to that of Zn plated steel with a plating amount in the range 60 to 90 g m·2 , which is widely used for automotive bodies today.4l The Zn-Cr alloy plating is obtained by electrodeposition at current densities over 0.5 A cm·2 from a sulfate solution containing zinc and trivalent chromium ions and some additives.5•6) The deposition current densities mentioned above are much higher than those for usual electroplating processes, e.g., Zn, Cu and Ni plating, carried out about 0.05 A cm·2 • Therefore, the time required for plating is very short; around 10-20 sec. Due to the high current densities, it seems reasonable to consider that the· Zn-Cr alloy plating proceeds under an unsteady-state condition and that the resulting coatings do not have a phase expected from equilibrium diagrams; no phase diagram of the Zn-Cr system with a full composition range has been available. 7). In other words, the alloy phase plated would be a non-equilibrium phase with unknown structures."

Jan 1, 2000

By C. M. Davidson

Contamination of by-product: sulfuric acid, by dissolved oxides of nitrogen ('nitrates') occurs under some operating conditions encountered in sulfide roasting and smelting,, notably when oxygen-enriched air is used. This 'nitrate' lowers the value of the acid and increases the effective cost of smelter gas desulfurization. The present paper describes measures taken at one smelter acid plant to remove this 'nitrate'; it discusses the mechanism by which 'nitrates' in some cases concentrate in one part of the plant and can be purged for more efficient treatment; and it describes a process developed by C-I-L Inc. for removal of 'nitrates' from such a purge stream. Advantages of the process include very low reagent cost, recovery of all sulfuric acid values and safe handling of nitrous fumes.

Jan 1, 1983

By B. S. Terry

Experiments have been conducted to assess the feasibility of capturing bearing emissions arsenic with CaO during the roasting of enargite (Cu3AsS4). Enargite/CaO mixtures have been heat treated in air, nitrogen or oxygen for various times and the products of reaction analysed by X-ray diffraction and cleaned analysis. The results show that substantial capture of arsenic can be achieved via the formation of calcium arsenates and/or calcium arsenides. In addition significant capture of sulphur is achieved by the formation of calcium sulphate andlor sulphide. Complete conversion to copper sulphide with total removal of arsenic can be achieved within 30 minutes at 700°C. Further heat treatment in air or oxygen leads to the formation of copper oxide and copper oxysulphate. Without optimisation of reaction conditions, it has proved possible to achieve retention of in excess of 85% of the arsenic content of enargite in the form of calcium arsenates.

Jan 1, 1994

By C. A. Summers

The U.S. Bureau of Mines applied process mineralogy to investigate a lead and zinc deposit located near Story Creek, Colville Mining District, Alaska. Mineralization is hosted by the Kayak Shale in veins, veinlets, and breccia. Sphalerite and galena, with supergene anglesite, occur in symmetrical quartz veins and between breccia clasts. The study sample analyzed 2.11 percent Pb, 5.37 percent Zn, 0.014 percent Cu, and 1.2 oz/ton Ag. Analyses of crushed products showed that 33 percent of the sample weight, and more than 50 percent of the Pb and 65 percent of the Zn, are in the minus 850 um fraction. Liberated grains of sphalerite and galena were found in crushed products finer than 300 um. Beneficiation tests indicate the material is amenable to processing by traditional gravity and flotation techniques.

Jan 1, 1991

By Hee Dong Jang

Crystalline metal oxide nanoparticles such as lithium cobalt oxide (LiCoO2) and indium tin oxide (ITO) were synthesized from sprayed droplets of aqueous precursor solution by flame spray pyrolysis. Complete thermal decomposition of the aerosol precursors was obtained at high flame temperature. Molar concentrations of the precursor solution, and the flow rate of combustion gas such as hydrogen, oxygen and air were varied to control particle size, size distribution and crystal structure. The crystalline nanoparticles synthesized were nearly spherical, and their average primary particle diameters ranged from 11 to 35 nm for LiCoO2 and from 8 to 15 nm for ITO.

Jan 1, 2006

By Junji Shibata

Zeolite synthesized from coal fly ash has many intelligent properties such as cation exchange, adsorption, catalyst and so on. The suitable use of the zeolite, however, is not established in an actual commercial scale yet. From the viewpoints of an effective usage of coal fly ash and the zeolite obtained from coal fly ash, we propose the new concept for environmentally friendly usage of zeolite, in which coal fly ash safely returns to the soil with growing plants and purifying wastewater. This method can make great contribution to recycle of coal fly ash, to purification of high nutritious water and to tree planting.

Jan 1, 2002

By M. B. Mesina

Mechanical separation systems are widely used nowadays for scrap metal processing, but they have natural limitations in product quality. The quality of the final product is considerably improved when sensors are used in the separation process. This paper describes new methods using sensors for scrap metal sorting and quality control. An example is the electromagnetic sensor, which uses the electrical and magnetic properties of materials to distinguish between different non-ferrous metals. The measurement results of two prototypes are reported. The benefits and the possibility to integrate such systems into practical applications regarding the processing of secondary raw materials are also described.

Jan 1, 2003

By C. F. Feng, L. Froyen

"In-situ processes have emerged as new and promising techniques for metal matrix composite fabrication. They offer significant technical and economic advantages over conventional processing. One of the in-situ processing routes that have been used is reactive free sintering of a mixture of powder reactants. However, materials synthesised via this route are always porous because of density differences between reactants and products. An example are the porous Al/(TiB2+Ah03) MMCs obtained by heating powder mixtures of Al+ Ti02+B with Ti02 and B in stoichiometric ratios for forming TiB2• In this study, porous Al/(TiB2+Ah03) composites were further processed by hot-pressing at temperatures above 600°C. This processing cycle was designed so that the composites could be densified. Furthermore, the reaction kinetics of the in-situ processing are studied by means of DSC analysis measured at different heating rates. The activation energies of the three intermediate steps that are involved in the reactive processing for preparing AV(TiB2+Alz03) MMCs are determined to be 923 kJ/mole, 241 kJ/mole and 235 kJ/mole respectively.XRD proved that the hot-pressed products consist of Al, TiB2 and Al203- Properties of the products are assessed by microstructural characterisation (LOM, SEM and EDS), microhardness, Young's modulus and bending tests. The results show that good microstructures, elastic properties and strengths, as well as acceptable ductilities were achieved. For the composition 79.74wt% Al-15.95wt% Ti0z-4.31wt% B, after the reactive free-sintering and hot-pressing cycles, Young's modulus is 105 GPa, bending strength is 509 MPa and maximum strain is 5.0%; for composition 88.73wt% Al-8.87wt% Ti0z-2.40wt% B, they are 89 GPa, 311 MPa and 8.2% respectively. It can be seen that the properties of products can be tailored by adjusting the relative amounts of reactants in green samples. Furthermore, for comparison reasons, Al and a binary system Al-Ti02 were identically processed as the ternary systems. Their microstructures and properties were studied."

Jan 1, 1998

By P. Koskinen

Outokumpu Oy has 30 years' experience in nickel production. It is mainly based on the technology developed within the company. The production chain starts from the mines reaching to the high-grade cathode nickel and the stainless steel manufacturing. As a multi-metal producer Outokumpu has the advantage to exploit from nickel raw materials also other valuable metals and intermediate products which can be processed at the company's various plants. The main source of nickel concentrate is nowadays the Enonkoski Mine started up in early 1986. It is the most modern mine in Finland being provided with the latest Finnish high-tech systems. Nickel concentrates are smelted at the Harjavalta Works using Outokumpu's internationally well-known flash smelting method. Also nickel containing residues and secondaries' are used as raw materials. The high-grade nickel matte from the smelter is then refined at the nickel refinery in a hydrometallurgical process, which was also developed by the company's own research staff. These processes have been continually improved and capacities gradually enlarged to 18 000 mtpy of cathode nickel. Besides plating, melting and superalloying purposes part of the nickel ends in stainless steel at the Tornio Works. The production was started in 1976 and has reached an established position on the European market.

Jan 1, 1988

By K. J. Richards

The converting of copper mattes to blister copper has seen few technical advances since the introduction of batch furnaces using submerged tuyeres over a hundred years ago. The first side-blown converting vessel, operated by P. Manhes in 1882, was an offshoot of the 'Bessemer steelmaking process, and subsequent improvements in the conversion of molten mattes resulted In the Peirce-Smith converter, still the Industry standard today. While Peirce-Smith' converting has served the industry well since the early 1900!s, increasingly stringent environmental regulations, burgeoning energy costs, and a trend toward continuous processing have set the stage for a major improvement in this area of copper production. In contrast to a growing number of approaches for continuous converting using molten copper mattes, Kennecott is developing a process for treatment of solidified matte which allows improved' control, higher oxygen enrichment and a separation or decoupling of smelting and converting operations not possible with the other converting technologies. The new process known as Solid Matte Oxygen Converting, or SMOC, eliminates the need for molten matte transfers, minimizes fugitive emissions, and produces high strength SO2 off gases which substantially reduce offgas handling requirements. The SMOC process, despite additional matte solidification and size reduction steps, offers both capital and operating cost advantages for new smelters and the upgrading of existing plants, when compared with conventional converting technologies. Capital cost reductions of up to 35% in converting, gas handling, and sulfur fixation are indicated. Kennecott has successfully tested the new process concept and continued' development work is now under way to commercialize the technology. This paper reviews the limitations of batch copper converting with emphasis on the need for a continuous process, previous industry approaches to continuous converting of molten mattes, and the new Kennecott development.

Jan 1, 1983

By Desmond Cook, Cynthia P. Dogan, Dale Govier, Gary Korth, James C. Rawers

"The microstructural and mechanical properties of iron powders processed in an attrition mill are highly dependent upon the processing environment. Extended high-energy ball milling in argon resulted in nanocrystalline bcc-Fe microstructure, while processing in nitrogen or alloying with carbon resulted in both nanocrystalline bcc-Fe and bct-Fe microstructures. In this U.S. Bureau of Mines study, both X-ray diffraction and Mössbauer analysis were used to show that the infused carbon and nitrogen concentrations were predominantly on the grain boundaries. Explosive consolidation resulted in a fully dense product with microstructure similar to the microstructure of the mechanically processed powder. Hardness values of the compacts correlated highly with grain size, independent of the processing conditions.IntroductionNanocrystalline materials have been theorized and shown to have unique properties that make them interesting for material scientists and promising for material engineering applications. Several conferences have been devoted solely to the techniques of preparing nanostructured materials have been held(l,2,3.). To date, most techniques used to generate nanocrystalline materials produce only a few grams of particles(1). High-energy ball-milling, however, is an efficient and effective technique that can produce substantial quantities of nanocrystalline materials with homogenous chemical composition that cannot be produced by conventional processing techniques(3).Applications and material evaluations of nanocrystalline materials require several grams of solid samples. Because nanocrystalline microstructures' are thermodynamically unstable, producing consolidated macro structures of nanocrystalline material has proved to be very difficult(2,3). In particular, retention of the nanocrystalline microstructure during consolidation of nanocrystalline particles has proven to be a problem. In contrast to many consolidation techniques that require elevated temperatures, explosive compaction uses a shock wave for consolidation( 4,5)."

Jan 1, 1994