Search Documents

By K. L. Whitehead

An examination of 60 mines, 11 illumination hardware manufacturers, and Q mobile face-equipment manufacturers was conducted to determine the state of the art of mine-illumination hardware, define lighting system installation and maintenance problems, and assess personnel acceptance of lighting. Longwall and mobile face-machine illumination were studied. Major problems on room and pillar installations include damage of exposed components, electrical failures, and reduced lamp life, with extreme variability in the degree of these problems. Most longwall systems had low or moderate maintenance requirements, cable damage being the most significant problem. Most mobile face-equipment operators liked their machines' lighting systems, but many complained of glare and other problems. Longwall lighting was unanimously accepted by face personnel, and most complaints were minor. Based on the survey, general installation and maintenance guidelines have been established, addressing hardware design aspects, approaches proved effective to minimize problems, and improper practices noted which are detrimental to effective lighting.

Jan 1, 1981

By George S. Rice

"The emission of hydrocarbon gases from coal beds and contiguous strata causes many accidents in coal—mine workings, the number of fatalities so caused being second only to those due to falls of roof. Gases tend to increase in amount with depth of coal mining, hence the danger of explosion is increased with depth. The pressure of the gas in virgin—coal areas at a distance from mine workings likewise tends to increase with depth from the surface, probably due to corresponding increase in hydraulic head and possibly, when the gas is held in nonporous formations, to greater ground pressure. The rise in gas pressure with depth under usual conditions is shown in wells drilled from the surface and in some coal fields in drill holes into the face of workings; however, under normal conditions of coal formation gas does not issue into workings under high pressure because the coal and adjacent strata have many bedding and joint planes which allow the gas to escape freely at the face of the workings. The rare occurrence of instantaneous outbursts of gas, with violent effects referred to later, constitute the exception.Variations of volume and pressure of fire-damp or methane found in different coal beds by wells at a distance from mine workings, are analogous to variations in volume and pressure of natural gas found in different gas and oil sands, although in general the pressure tends to increase with the depth. Sometimes, however, in tight sands higher in the formation the pressure of gas therein is abnormally high, and on drilling the well deeper gas in the lower strata may be found at lower pressure."

Jun 1, 1934

By K. Thirumalai

This study forms a part of Bureau of Mines continuing research on thermal fragmentation of rocks. The potential of internal heating techniques for rock fragmentation is discussed. A concept of rock fragmentation with rapid inter¬nal heating of a localized inner volume of rock is advanced The energy required for rock fragmentation is made available by creating a required vol¬ume of localized heating. The fragmentation of rock using the proposed method is analyzed and qualitatively compared with the results of experiments with Charcoal granite, Dresser basalt, and Sioux Quartzite. High frequency dielec¬tric heating below 100 MHz is used in the study as an example to examine the working of the concept. The selection of operating conditions for the experi¬mental heating is explained. Fragmentation of Charcoal granite and Dresser basalt test rock blocks is achieved for localized heating below 550° C. The heated volume required for fragmentation is observed to be less than 2 percent of the test block volume and the electrical energy consumption is in the order of 3.5 to 6 5 kwhr/m3 The method offers a possibility for in situ fragmenta¬tion of rocks, favorable for internal heating. The method is highly dependent on rock properties governing internal heat generation The efficiency of dielectric heating in the experimental study is observed to increase with increasing dielectric loss of the rock material, ranging from about 10 percent in Sioux. Quartzite to about 50 percent in Dresses basalt

Jan 1, 1970

Geological discontinues in the coalbed, such as faults, sandstone channels, permeability facies, lithotype changes, and large scale partings in the coal seam, can cause intermittent production problems or produce unexpected amounts of water or gas from degasification boreholes. These discontinuities not only can impact methane emissions into the mine workings, especially if they hinder proper and effective degasification of the coalbed but may act as conduits for methane flow from gassy strata into advancing mine workings. The effects of these discontinuities are still under debate by mining and gas production experts. This study presents a numerical investigation using reservoir simulations of the effects of partings and permeability facies and lithotype changes on the production performances of vertical and horizontal degasification boreholes, as well as the emissions during longwall operations. In this work, the grid block was designed in a multi-layer 3-D structure which enabled spatial descriptions of the geometries and properties of the discontinuities within the coal seam. The studied coal seam discontinuities and their properties were distributed arbitrarily within the model. Production was simulated by vertical and horizontal boreholes. Degasification boreholes operated two years prior to start of the mining. The results of this numerical study show that in coal seams with major heterogeneities and discontinuties, the geometry and location of the boreholes are important for improved gas production. These considerations are also important for controlling methane and water inflow into the working environment during longwall mining.

Jan 1, 2008

By G. L. Oldright, Virgil Miller

"This paper is the tenth 4 of a series on smelting in the lead blast furnace, and the fifth 5 on modifications brought about by the introduction of richer charges.ACKNOWLEDGMENTSAll of the data on handling rich charges in lead smelting given in this recent set of five articles describing the results of a cooperative study by the United States Bureau of Mines and the University of Utah were obtained through the courtesy and with the cooperation of the staff of the Bunker Hill & Sullivan Mining & Concentrating Co. at Kellogg, Idaho. The authors acknowledge with appreciation the assistance given by Stanly A. Easton, vice.-president and general manager, F. M. Smith, smelter director, and A. F. Beasley, smelter superintendent, whose generosity, sympathy, and assistance made it possible to obtain this information for the mining industry.GENERAL DISCUSSIONWhen the charge has been dropped into the lead blast furnace, it is out of control of the operator to the extent that, whatever the material is, it must practically all be melted and run out of the blast furnace. The necessary uniformity of mixture to produce slags of regular composition and the choice of the slag—forming ingredients and products to be formed can be made only before the charge to dropped.It was found (R.I. 3096) at Kellogg, where the charge is mostly sinter, that the ratio of the slag—forming ingredients taken from each tuyere was nearly constant, in contrast to the irregular composition of slags taken similarly from a furnace whose charge consisted of ingredients differing greatly in chemical and physical nature, including size. If the charge consists almost entirely of sinter, the blast furnace should then operate more uniformly."

Aug 1, 1932

By D. Bienstock

As part of the development of the hot-carbonate scrubbing process by the Bureau of Mines, the corrosion rates of steel in boiling solutions of potassium carbonate saturated with carbon dioxide and hydrogen sulfide were determined, and the effectiveness of various inhibitors was evaluated by Bureau researchers. The highly corrosive solution of carbonate saturated with carbon dioxide can be inhibited with a 0.2-percent concentration of either potassium chromate or sodium metavanadate. Solutions of carbonate saturated with carbon dioxide and hydrogen sulfide are mildly corrosive, 0.01 inch per year. Complete absence of corrosion is obtained with 0.2 percent sodium metavanadate or 0.15 percent vanadium pentoxide. Oxidizing inhibitors such as potassium chromate are destroyed in the alkaline sulfide mixture, N-alkyl trimethylene diamines, at a concentration of 0.1 percent, lower the corrosion rate to about 0.005. Sodium metasilicate, at a concentration of 0.6 percent, completely inhibits the corrosion but may deposit free silica in the system. Commercial cladding materials such as the epoxy coatings also prevent corrosion.

Jan 1, 1962

By John C. Edwards

A computer program, developed for the Bureau of Mines under contract, predicts in a quasi-steady-state approximation the ventilation and contaminant concentrations and temperatures when a fire occurs in a multi-level mine. For periods of time in which there is no significant change in the ventilation, yet a fire is producing fumes, a real-time fume concentration throughout the mine is calculated. Multiple and time-variable contaminant sources can be simulated. Recirculation paths that can develop provide a mechanism for increasing the fume concentration in the mine network and are identified by the computer program. This report contains a listing of the Fortran computer program as well as the required format of the input data. Two examples are provided of the real-time spread of smoke from a fuel-rich fire throughout a multilevel mine. The first example considers an operational exhaust fan as well as a booster fan. The second example evaluates the real-time smoke spread following a failure in the exhaust fan; recirculation occurs in this latter case.

Jan 1, 1982

By K. L. Cashdollar, C. K. Man, J. R. Gibbins

Oxyfuel combustion is currently one of the principal technological options being considered for capturing carbon dioxide from pulverised coal power plants. In oxyfuel combustion, coal is burnt in a mixture of recycled flue gases and added oxygen instead of in air. In principle this yields a flue gas containing only carbon dioxide, water vapour and small amounts other impurities. Oxyfuel combustion is superficially similar to combustion in air, but there are inevitable differences. This paper describes ignition tests on pulverised coal suspensions using a suite of coals of different rank and from different countries of origin and over a range of oxygen and coal concentrations of interest for oxyfuel combustion. The ignition tests were carried out using the National Institute for Occupational Safety and Health (NIOSH) 20-litre explosion chamber. The purpose was to determine how easily the various coals ignite and burn in mixtures of O2 and CO2 compared to their combustion in air. The residual char volatile and ash contents for the ignition residues were measured using a thermogravimetric analyser (TGA), allowing Q factors (i.e., enhancement in apparent volatile yield due to higher heating rates and/or heterogeneous reactions) to be determined and compared. An ignition index has been derived from the explosion and char data. This index has been used to rank low volatile coals for ignition propensity in air. The results show that to obtain ignition and combustion comparable to that in air, the oxyfuel O2-CO2 gas mixture must contain over 30% O2. Keywords: CO2 capture, combustion, pyrolysis, oxyfuel.

This Bureau of Mines report reviews the information presented at the Sixth Mineral Waste Utilization Symposium cosponsored by the Bureau of Mines, U.S. Department of the Interior, and the IIT Research Institute. Environmental scientists and engineers from nine countries participated in the symposium, which was held May 2-3, 1978, at the Chicago campus of IIT Research Institute. The 56 papers presented on the reclamation and recycling of mining and mineral wastes, municipal solid waste, industrial wastes, and scrap metal are summarized herein.

Jan 1, 1980

By Harold W. Lipper

BUREAU OF MINES helium plants produced a. record-breaking 477 million cubic feet of this essential element in 1959. The supply of helium was less than the demand before operations were resumed at the Navajo plant in July and begun Sit a. new plant at Keyes, Okla., in August. Helium was in abundant supply after August, and the informal allocation system which had been in use intermittently since 1955 was discontinued Delivery of 26 new tank cars in August and September increased the total in the tank-car pool to 163. Defense and space agencies and the Atomic Energy Commission continued to use more helium in their operations and research.

Jan 1, 1960

By William H. Pomroy

Fire on surface mining equipment is a serious hazard to life and property. The Bureau of Mines, through a program of contract and in-house research, has developed and in-mine demonstrated reasonably priced, reliable automatic fire protection systems to deal with this problem. This report reviews the development and subsequent testing of systems for haulage trucks, front end loaders, coal augers, dozers, drills, and shovels. A variety of fire sensors, extinguishing agents, and control systems arc discussed in the context of mine equipment designs and operating environments

Jan 1, 1980

By W. M. Bangert, F. S. Boericke

"INTRODUCTION Determination of the thermodynamic properties of metallurgically important compounds of chromium has been one of the activities of the Pacific Experiment Station of the Bureau of Mines. Earlier reports have dealt with the entropies 4/ 5/ of chromium, chromic oxide, and chromous and chromic chlorides, with the thermodynamic properties of the chlorides of chromium, 6/ and wits the thermodynamic properties of the carbides and oxide of chromium. 7/ Evaluation of the thermodynamic properties of chromite, FeO.Cr2O3, is desirable, as this material in impure form constitutes the only natural source of chromium of any consequence.Two general methods are available for directly determining heats of formation - (1) measurement of heats of combustion and (2) measurement of heats of solution. Neither of these methods is directly applicable at present to ferrous chromite, which accounts for the lack of previous data. Combustion of a stoichiometrical mixture of iron and chromium under conditions prevailing in a calorimetric bomb yields a mixture of iron and chromium oxides rather than chromite. None of the usual calorimetric solution media dissolve chromite at temperatures low enough for solution calorimetry. Sulfuric acid and an oxidizing agent, such as MnO2 or CrO3, are known to dissolve chromite, but the possible calorimetric use of t is medium would require long preliminary investigation. Consequently, recourse must be taken to some indirect method. At the start of the present work, the most promising method appeared to be the determination of equilibria in the selective, reduction of the iron in chromite by hydrogen;"

Jun 1, 1945

By R. L. King

This report describes a method for designing and constructing ground beds that has been developed under the sponsorship of the Bureau of Mines. The procedures for designing and constructing a driven-rod ground bed with a resistance of 5 ohms or less are given. Some of the theory of soil resistivity and fall-of-potential resistance measurements is included. Results of a bed constructed at the Bureau of Mines mine car roadway are presented.

Jan 1, 1978

By Christopher Mark, Gregory M. Molinda, Timothy M. Barton

The Coal Mine Roof Rating (CMRR) was first presented at this Conference nine years ago. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, and extended cut evaluation. It has also become truly international, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. The purpose of this paper is to bring the mining community up to date with recent improvements and applications of the CMRR. The most important new development is a streamlined process for determining the CMRR from exploratory drill core. Just three types of information are now required: •Fracture spacing (or RQD) •Uniaxial compressive strength (or axial Point Load Testing) •Diametral Point Load Testing The moisture sensitivity adjustment has also been changed, and new research has related the immersion test to slake durability. Most recently, the CMRR has been implemented in a computer program, which can be obtained from NIOSH free of charge. The program facilitates calculation of the CMRR from either underground or drill core data. Values from many locations can be saved in a single file, and an interface with Autocad allows CMRR contour plots to be integrated into mine planning.

By Jeffery L. Kohler

This final report on Bureau of Mines Contract J0338028 presents the results of a research effort to predict incipient failure in electric-power-system components. The development of continuous monitoring techniques to detect an incipient failure would represent a significant improvement in system maintainability, availability and safety, This report describes the analytical and experimental aspects of the project. Mathematical models have been developed to study the behavior of cables and motors which are undergoing a deterioration process. These models allow a detailed study of the effect of deterioration on the component's terminal characteristics and performance. The efficacy of using negative-sequence monitoring is a reliable indication of deterioration has been established. Techniques for assessing the sensitivity of the prediction algorithm to component deterioration have been presented. An approach for modelling electrically-excited vibrations, and including these in the algorithm, has been presented.

Jan 1, 1987

By Rudolf E. Greuer

The existing computer programs for the simulation of ventilation systems under normal ventilation conditions are reviewed and a suitable program for including the influence of mine fires is selected. New program parts are written for the consideration of methane productions in coal mines, heat and gas productions of mine fires, temperature and air composition changes in ventilation systems, and the ventilation forces resulting from the latter. Other program parts are provided for the detection of danger zones and reversed air currents and for the inclusion of recirculated air currents in the network analysis. Existing program and new program parts are combined. The resulting new program can be used for a multitude of assignments. It is designed for the practical ventilation engineer and should be applicable to all types of ventilation emergency plans, in particular mine fire plans. The organization of the program and its mathematical basis are described. A FORTRAN IV listing and several flow diagrams are included. Eight executed examples are discussed, input and output for these examples explained. Storage requirements and execution times are estimated.

Jan 1, 2011

By Dennis R. Dolinar, Gabriel S. Esterhuizen

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

By H. R. Babitzke

As part of a continuing project to develop refractory metal alloys for high-temperature structural applications, the Bureau of Mines applied solid solution and precipitation strengthening techniques to improve the properties of columbium alloys. The purpose was to investigate the effects of hafnium, tungsten, and boron on the formability, strength, and oxidation resistance of columbium. The experiment was of factorial design with two replications which called for 72 ingots of 36 basic compositions, weighing 150 grams each. Hafnium, tungsten, and boron were evaluated at 3, 3, and 4 levels, respectively. Values of alloy content are all in atomic percent. The highest strength observed was 29,000 psi at 1,200° C for alloys Cb-15Hf (No. 3), Cb-7.5Hf-5W-2B (No. 14), and Cb-15Hf-5W-2B (No. 15). At 1,200° C, the ternary alloy Cb-15Hf-5W (No. 6) which has shown good properties in previous Bureau of Mines investigations was the most resistant to oxidation For boron additions, the alloys oxidized more readily with increasing amounts of this element. The fabricability of the alloys high in boron became increasingly difficult, resulting in an inadequate number of alloys required for a complete statistical analysis for all the tests. As a result of the decrease in ductility, an insufficient quantity of tensile samples were available for a proper analysis for the high-temperature strength data.

Jan 1, 1970

By K. K. Kelley

"INTRODUCTION The Bureau of Mines nitrogen peroxide process (2) 3/ for extracting manganese from low-grade ores is essentially a two-stage process involving the reversible reactionMnO2 + 2NO2 + 6H2O = Mn (NO3)2 . 6H2O (1).At lower temperatures this reaction proceeds to the rigth and affords a means of dissolving manganece and separating it from unreacted ore. At higher temperatures the reaction proceeds to the left and manganese dioxide is recovered and nitrogen peroxide regenerated for recycling. Evidently, therefore, the energy required for decomposition of manganous nitrate is a matter of practical importance. Similar information for certain other nitrates also is desirable beceuse the nitration step of the process produces appreciable amounts of nitrates of other metals, such as iron, aluminum, magnesium, calcium, and barium, some of which are not broken down in the evaporation and decomposition steps. Thus, a portion of the nitrogen peroxide is not directly available for recycling. Whether or not it is feasible to recover nitrogen peroxide locked in the more-stable nitrates depends partly on the energy required and the conditions necessary for their decomposition.To supply information bearing directly on these subjects, several researches were undertaken at the Pacific Experiment Station: (a) Heats of formation (24, 25, 26) of nitrates of manganese, magnesium, calcium, barium, and aluminum were measured at 298.2° K:; (b) low-temperature specific heats (23), in the range 51° to 298.2° K,, and entropies of nitrates of magnesium, calcium, barium, and aluminumm were determined; and (c) heat contents (21) above 298.2° K. of the nitrates of manganese, magnesium, calcium., and barium were measured. The results of these studies, when correlated by thermodymamic methods, permit evaluation, at any temperature of interest, of the energies required to decomposethe nitrates and furnish information concerning the equilibrium pressure temperature relationships."

Sep 1, 1944

By H. B. Hill

The West Red River oil field, in Tillman County, Okla. (fig. 1), is approximately 8 miles northwest of the town of Burkburnett, Wichita County, Tex. The wells are in the river bed between the medial line and the south bank of the Red Diver. In the following discussion of the geology, development, and exploita-tion of the field, the authors have, by means of structure maps, crews sections through various parts of the reservoir and tabulated development data and production statistics, recorded salient information on a field whose development was unique and in some respects unusual for fields discovered and initially developed more than a quarter of a century ago. The total oil production from Government-operated leases; considered in the report was 6,900,440 barrels to January 1, 1947, from 3 proved acres developed by H1 oil-producing wells, 10 gas-injection wells, and 5 nonproductive wells. A calculated past recovery of 60P, barrels of oil per acre-foot and an estimated ultimate recovery of 6.S0 barrels of oil per acre-foot under present gas-injection methods begun in 1929 in shown.

Jan 1, 1949