Search Documents

By D. J. Dollhopf

An overburden handling dragline operation was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to determine the degree a dragline could mix overburden inhibitory zones during the spoiling process. In order to quantify the mixing process the overburden was: 1) scatter spoiled; 2) dump spoiled; and 3) spoiled in a normal manner. This demonstration was part of an effort to investigate means of reestablishing non-polluted hydrological systems in areas where surface mining directly impacts shallow ground-water resources. When inhibitory material constituted < 5% of the total overburden volume, such material was essentially not detectable in the resultant spoil pile. When inhibitory material exceeded 15% of the overburden volume it was always found in the resultant spoil pile, generally with a smaller extent, indicating partial dilution. Inhibitory overburden zones often reappeared at the base or top of spoil piles in the potential aquifer and root zones suggesting the need for selective placement procedures. Scatter spoiling did not appear to be significantly more effective than normal spoiling, however clump spoiling seemed to produce less mixing of inimical zones. Mining activity has reduced ground-water levels within 1600 m of the active pit. The aquifer which is developing in spoils appears to have similar confinement characteristics as those that existed in the premined aquifer. To date no definite trends have been observed concerning changes in surface or ground-water chemistry associated with mining.

Jan 1, 1978

By W. W. Cutler

An oil-field drilling campaign is used in this paper to signify the spacing of the wells to be drilled as well as the drilling program, which is interpreted as the number of wells drilled in a unit of time, This has an important bearing upon the time of receiving income, as well as upon the amount of revenue obtained In periods of low prices for oil, such as the present, the margin of profit is at the best very small, and the correct determination of the drilling campaign may be the deciding factor between incurring financial loss or gain during the depressed period. General policy of the operator. Drilling should be planned by the field engineer to conform with the general policy of the operator. This policy may be one of conservation daring the early life of the property, but as mentioned later, this may result in a smaller ultimate recovery it often occurs that the market price of oil does not warrant rapid development, or it may be desirable to hold in reserve a supply of oil for a refinery. The policy may be to recover all of the oil as quickly as possible, or it may be to maintain a constant and sustained production. In any case, the operator should, outline as far as possible a definite policy, and should understand the principles underlying the recovery of oil, the influence of rapidity of drilling and effects of spacing, in order that he may obtain the oil as required with the least expenditure.

Jan 1, 1921

By Frank K. Cameron

"The DepositsThere are two large deposits or groups of deposits of potash salts which, at the breaking cut of the great world war in 1913 and for several decades preceding, were practically the only commercial sources of supply for the entire world. In both cases the origin of the deposits was sea water, the potassium salts being deposited by desiccation, but there were modifying factors which were not entirely the same in both cases so that well defined and important differences exist in these deposits. The larger and better known group, called the Stassfurt Deposits, are in Germany in the region about or adjacent to Magdeburg and Halberstadt. The general character of these deposits and the methods for recovering potash from them have been frequently described, not only in technical publi¬cations, but in the non-technical propaganda long maintained by the Kali Syndikat, an organization founded on a ""cartel"" with the supervision and support of the late Imperial German Government.Less well known are the smaller though nevertheless extensive deposits in the neighborhood of Mulhouse in Upper Alsatia, which were also under the control of the Kali Syndikat at the breaking out of the war but have now passed to French control, with the reentrance of Alsace into the French Republic.The Alsatiaa deposits, while less extensive than the German deposits, are, nevertheless of great magnitude. They occupy a large part of the area between the Vosges Mountains and the River Rhine, from Col¬mar on the North to Mulhouse on the South. Indeed a few borings on the East bank of the Rhine indicate that the deposits may extend under the river and to some distance beyond Buggingen Linken, Baden, though it has not been Shown as yet that this extension is of commercial significance.As is well known, the Stassfurt potash occurs as potassium chloride or potassium sulphate or both salts, intimately mixed with salts of sodium, magnesium eau& calcium (lime) and contaminated with substances. insoluble in water such as ferric oxide, clay etc. The potash salts are segregated in more or less extensive 'pockets' throughout the salt mass, these segregations departing usually from the horizontal. But the main ""potash region"" is a stratum varying from 30 to 150 feet in thickness and at a depth requiring shafts 5000 feet."

Jul 1, 1919

By Gerald G. Johnson

The use of the Scanning Electron Microscope to characterize Coal Mine Dust has been possible because of two circumstances. First, the imaging process of the SEM allows multiple signals (secondary electrons, back scattered electrons, x-ray emission, etc.) to be viewed. Second, the use of a computer to analyze the signals and perform statistical tests on the results. The parameters described are size, shape, chemical composition, mass distributions, and particle thickness. Although the system is intended for particular systems, those of agglomerates (whether tile same or not) are handled by special aspects of the computer programs. The work on fibers is not completed at the time of this report. This work discusses the hardware (developed especially for this process) and software (both on an IBM 360/370 and a PDP 11/20). The latter system allows direct interaction between the operator of the SEM and computer for maximum information at the least time.

Jan 1, 1979

The evident need to improve the reliability of fluid power systems in underground coal mining equipment prompted the U.S. Bureau of Mines, and later the Department of Energy, to contract with the Fluid Power Research Center at Oklahoma State University for a research project to develop methods for achieving this end. Since the work of the contract was completed at about the time DOE was relinquishing its underground coal mining projects to BOM it was decided to issue the final report under 80M cover. The contract revealed that the major causes of poor reliability were: (1) poor overall system design, (2) poor component contamination toleranace, (3) poor system filtration, and 4) poor maintenance practices stemming from a lack of defined maintenance procedures and enforcement of same. This report demonstrates the variability of the reliabilities of components of similar performance description when subjected to standard tests. Improved design procedures are recommended and the information needed to specify and select components whose reliability is predictable and optimum without sacrifice in performance or significant increase in envelope size.

Jan 1, 1983

By John E. Conley

Of the three chemical elements most vitally essential for plant growth the United States, before World War I, had developed ample domestic supplies of but one-phosphorus. During and shortly after the war period, the fixation of nitrogen was greatly expanded in this country, as in many others, insuring a supply adequate for agriculture as well as for munitions. However, in spite of a search for sources of the third element, potassium, which began years before the war, attained almost frantic intensity between 1914 and 1919, and continued for 10 years thereafter, it was not until 1921 that the American Trona Corporation put its Searles Lake operations into continuous production. This company in 1926 became The American Potash & Chemical Co. but has never supplied much more than 15 percent of the potash consumed in the American market. Likewise, though discovered in 1921 in drill cuttings from oil wells, it was not until 1926 that domestic deposits of potassium salts adequate to render the United States independent of foreign sources of supply were proved to occur in the Permian Basin of Texas and New Mexico.

Jan 1, 1944

By G. W. Luxbacher

This volume describes the use of the Penn State Mine Ventilation Simulator (PSU/MVS) to model existing mine ventilation systems and, in addition, to evaluate the effect of system modifications. Ventilation survey methods designed to insure computer input data of sufficient accuracy for simulation purposes are covered in comprehensive detail, including quantity and pressure measurement and fan performance testing. The development of input data from ventilation survey results is discussed and illustrated by the use of an actual field survey. Two programs, written in FORTRAN IV with WATFIV, are presented to calculate airway head losses from altimeter pressure measurements. An existing coal mine ventilation system is analyzed and modifications to the system are simulated and evaluated. In addition the application of the PSU/MVS to non-coal mines is briefly discussed. An extensive bibliography on ventilation surveying and simulation is included.

Jan 1, 1977

By Ann G. Kim

The U.S. Bureau of Mines mine fIre diagnostic methodology to locate and monitor fIres in abandoned mines and waste banks is based on the controlled sampling of the mine atmosphere to determine changes in the concentration of hydrocarbons desorbed from heated coal. To provide background data for this methodology, a laboratory study was conducted in which samples of coal and coal waste were heated under controlled conditions. Gas samples from the combustion furnace were analyzed for standard gases CO2 and CO and for the C1 to Cs hydrocarbons. In all tests, the concentration of desorbed hydrocarbons increased during heating and decreased during cooling. A dimensionless hydrocarbon ratio, Rl, was developed as the signature for heated coal. For bituminous coals, the value of Rl increases during heating of coal samples and decreases during cooling of the same samples. Generally, Rl values of 100 or more indicate coal sample temperatures of at least 100° C. The emission of higher molecular weight hydrocarbons from anthracite samples was very low, resulting in relatively low Rl values at all temperatures. Data from fIeld projects confIrmed these results.

Jan 1, 1991

By John P. Capp

Information is summarized on the major uses of fly ash and prospects for utilization in agriculture and in brick and mineral-wool manufacture. Technological aspects of utilization are discussed and references are given to the work of many of the leaders in the fields of fly ash production, processing, and utilization.

Jan 1, 1970

By W. G. Diamond

Lightweight aggregates have become increasingly important to the construction industry. From 1953 to 1960, the quantity of the aggregates used in concrete block, precast and prestressed concrete, and monolithic structures increased about 92 percent. The present study was conducted in Bureau of Mines Area IV which encompasses the South-Central States of Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas. This is an administrative area and does not delimit a market area or imply an economic unit. Because of the increasing importance of metropolitan areas in evaluating economic growth, significant data showing relationships between growth of the metropolitan areas and the lightweight aggregate industry are included.

Jan 1, 1964

By George H. Holmes

This paper is one of a series on mining methods and practices published by the Bureau of Mines. It describes quarrying methods and crushing practices of the U. S. Lime. Products Corp. at its Sloan and Apex quarries. Calcining and milling processes. at the Sloan and Henderson plants also are outlined. The Sloan dolomite and limestone quarries and plant are in secs. 12 and 13, T. 23 5., R. 60 E., and sec. 18, T. 23 S., R. 61 E., M.D.B. &M., Clark County, Nev., about. 17 miles by paved highway southwest of Las Vegas (fig. 1). The Apox limestone quarry, and crushing plant are in sec. 26, T. 18 S., R. 63 E., M.D.B.&M., Clark County, Nov., approximately 18 milos northeast of Las Vegas, adjacent to U. S. Highway 91 (fig. 1). The Henderson calcining plant is Inc., in sec. 13, T. 22 S., R. 62 E., 14 miles southeast of Las Vegas on U. in a reduction unit of Basic Magnesium, M.D.B. &M., Clark County, Nev., about S. Highway 93 (fig. 1).

Sep 1, 1949

By Herbert H. Einstein

Appendices A through M contain information that is the basis for many developments reported in the main text (Parts I through V); this information is, however, not needed in applying the research results. Specifically the appendices contain: A: Geology of Sampled Sites B: Comparison of Distribution Forms with Observed Trace Length Frequencies C: Joint Attitude Pole Diagrams D: Resistance and Deformability of Rock Discontinuities E: Resistance and Deformability of Joints - Details of Data Recording Procedure F: Documentation and Details for Simplified 2-Joint Wedge Analysis G: Generalization of the Stiffness Approach H: Inadequacy Due to Simplifying Assumptions in Wedge Analysis I: Rock Slope Reliability Analysis: State of the Art J: Resistance Derivations for Mechanical Model K: Supporting Derivations for Analysis Method DAYLITE L: Supporting Derivations for Simplified 2-Plane Reliability Analysis M: Plots of SLOPESIM Runs

Jan 1, 1979

This Bureau of Mines publication summarizes the industrial minerals industry of Idaho. It contains information on 119 principal deposits of 21 commodities in the State and describes the institutional and infrastructural factors affecting mineral development.

Jan 1, 1991

By Nirander M. Safaya

Revegetation success on surface mined lands is dependent upon the nature of the plant growth media. Soil physical and chemical properties dictate the needs for specific reclamation and subsequent management practices. Field experiments were conducted at six coal mine sites in Oliver and Mercer Counties, North Dakota to determine the subsequent effects of a single application of selected amendments on spoil and topsoils over the five year period, 1974-1978. Considerable variations in the physical and chemical properties were found in mine spoils from site to site. The texture of spoils ranged from sandy clay loamy at North Beulah I to loamy at Glenharold, and from sandy loamy at North Beulah 3 and South Beulah sites to loamy sands at the Center site. The pH of the sites ranged from 6.5 at South Beulah to 8.2 at North Beulah 3. In many cases, the pH values of mine spoils were not significantly different from the topsoils. The electrical conductivity (ECe) did not exceed 6 mmhos cm-1 at the test sites even though in other studies much higher values were recorded in the same vicinity. The spoils from Glenharold and North Beulah test sites can be classed as moderately saline, and those from Center and South Beulah as non-saline. The sodium adsorption ratios (SAR) varied from less than 1 to 32, with highest values in the spoils of North Beulah 3 followed by Glenharold; all other sites were nonsodic. Lowest SAR values (less than 1) were found in the topsoiled sites at South Beulah and Center. Spoils of North Beulah 3 test site were highly calcareous, followed by North Beulah 2 and Glenharold. Center mine spoils which were the least calcareous of the test sites, showed the calcium carbonate equivalent three times higher than that of the topsoil. The average calcium concentrations in the spoils of North Beulah 3 and South Beulah test sites were -13 and 14 me 100g -l while at North Beulah 2 and Glenharold test sites 25 and 22 me 100-1-1 were recorded, respectively. The overall magnesium concentrations ranged from an average of 4 to 16 me 100g 1. Sodium concentrations in all sites never exceeded 10 me 100g-1. Phosphorus concentrations on the average at North Beulah 1, North Beulah 2, and Center were 10.2, 4.6, and 22.2 µg g -1 spoil, respectively. Concentrations of potassium ranged from 200 ppm at South Beulah site to more than 375 pp in at the Glenharold site. High concentrations of sulfates (239-2778 µg g-1) seem to contribute to the salinity in these spoils. Chloride concentrations of spoils were low and never exceeded 40 µg g-1 spoil. Based on established critical levels of deficiency for micronutrients in agricultural soils, it seems that none of these were deficient. However, controlled environment experiments did reveal increased plant growth responses when some micronutrients were added to the mine spoils. Treatment effects were highly site specific depending on the nature of the soil/spoil characteristics and, of course, the properties of the various treatments. While slack coal amendment to the spoils at North Beulah 2 site affected significant increases in a large number of variables (both major and trace elements), amendment of the topsoils at the South Beulah test site with leonardite resulted in significant decreases in a number of variables, particularly trace elements. Spoils at Glenharold and North Beulah 3 demonstrated the fewest significant changes due to amendments. Calcium, magnesium, strontium, organic matter and nitrogen were consistently increased from site to site with the addition of lignitic materials. Other spoil/topsoil physical and chemical properties (30 variables) as affected by amendments and time are discussed.

Jan 1, 1982

By James R. Dunn

Samples were taken of industrial mineral waste materials which are potentially capable of being used for filling underground coal mines for subsidence control in the Pittsburgh and the Scranton-Wilkes Barre areas of Pennsylvania. The samples were subjected to potentially relevant standard tests which are commonly used 1n the evaluation of soil materials and mineral "aggregate materials. Measurements of plasticity, liquid limit, and gradations, particularly in the -200 mesh size range, indicated a comparative lack of clay minerals. Cementitious reactions between sources of alkali, such as calcium hydroxide or portland cement stack dust, and of silica, such as clay or fly ash, were found to occur in various mixes of high-bulk materials. Strengths of up to about 400 psi at 84 days were observed. The possibility of emplacement of high-bulk material by both turbid flow (or density currents) below water and by mud flows above water were considered and both appear to be reasonable and possibly simpler than the current mechanisms of emplacement.

Jan 1, 1977

By J. W. Thompson

That the governor is hereby authorized to appoint a commission of seven persons, to be known as the industrial accidents commission-two of whom shall be employers of labor, two of whom shall be employees in either mines or industrial establishments of this Commonwealth, or duly accredited representatives thereof, two of whom shall be learned in the law, and one of whom shall be a person skilled and experienced in making investigations-to inquire into the causes and results of industrial accidents in the mines, mills, factories, stores, and upon the railroads, street railways, ships, wharves, and in all industrial establishments, and in all other places where men, women, and children are employed in manual labor in this Commonwealth; to study the most advanced methods for safe-guarding against these accidents; to inquire into the subject of fair compensation for those who are injured in these accidents, and for the families of those who shall be killed as a result thereof; and to study the operation and effect of the Workmen's Compensation Law of 1913. SEC. 2. The chairman of said co~mission shall be designated by the governor, and the person named on said commission as a skilled and experienced investigator shall be the secretary of the commission, The commission shall have power to employ such legal counsel and other officers and employees as it may deem necessary to properly perform its duties. SEC. 3. The secretary of said commission shall receive an annual salary of $2,400 and his actual necessary expenses; and the other members of the commission shall receive no compensation for their services, but shall be allowed their actual traveling and other necessary expenses. The salaries of any other persons employed by the commission shall be fixed by it.

Jan 1, 1920

By Joseph B. Cummings

"INTRODUCTION The property was first examined by an engineer 3/ of the Bureau of lanes in December 1942 and was later investigated by the sane engineer in January and February 1943. Prominent outcrops and underground exposures of high-grade iron ore, together with mention of sizable intersections of hematite in logs of four widely scattered churn—drill holes, indicated the possible occurrence of a substantial tonnage of iron ore at this old copper producer.From March to May 1943, detailed topographic and geologic mapping of the property was done by the Federal Bureau of Mines, the Federal Geological Survey, and the Arizona Bureau of Mines.Funds were allotted for exploration of the property by churn and diamond drilling. This work was started in December 1943 and completed in June 1944.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Nines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts, developed by each exploratory project as soon as practicable after its conclusion. The Mining Drench, Lowell B. Moon, Chief, conducts preliminary exmination, performs the actual exploratory work, and prepares the final report, The Metallurgical Branch, P. G. Knickerbocker, Chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision Dr. R. S. Dean, Assistant Director."

Dec 1, 1946

By E. O. Wagner, A. W. Koth, V. F. Parry, J. B. Goodman, D. C. Gernies

"INTRODUCTION A commercial-scale pilot plant for gasification of lignite was completed by the Bureau of Mines at Grand Forks, N. Dak., early in 1945 as an extension of work on, gasification of low-rank coals initiated in a smaller pilot plant at Golden, Colo., during 1943. The development work on this plant was part of a program to make reducing gases from lignite for beneficiation of low-grade iron ores. The background of this project has been described in a previous report. 6/ The present report describes the major features of the large pilot plant, a record of experimental operating data during five runs totaling about 1,800 hours, .and results of experimental work on the small pilot plant at Golden during 1945.This project has created considerable interest because heretofore there has been little success in several attempts to gasify American lignites.Furthermore, the methed employed is a departure from conventional processes. Natural lignite is fed continuously into an externally heated annular retort and is converted into water gas by heat conducted through alloy metal walls. Because of the high thermal conductivity of metal, the rate of gasification is several times greater than can be obtained when employing refractory walls. The process has been developed to a part that leaves one major question unanswered. - ""How long will the alloy last under practical operating conditions?"" - and this question has aroussed the interest of the Coal Division of the Bureau of Mines in this new development.Owing to the high reactivity of the lower-rank fuels, the water-gas reactions proceed rapidly at medium temperatures of 1,650°F. to 1,800°F. These temperatures can be attained in a reaction zone heated by external means when the temperature of the retort does not exceed 1,900°F. while transferring from 6,000 to 7,000 B.t.u. per hour per square foot. Such rates are several times greater than can be attained through refractory walls as employed in the Didier-Bubaig 7/ and the Ahrens processes. 7/ Therefore, the investment cost of the gas generator per unit of capacity will be considerably lower for the higher-capacity process. However, the maintenance cost of metal vessels will be higher than that of refractory retorts, and this emphasizes the importance of large-scale operation to determine the life of an alloy retort under practical operating. conditions."

Sep 1, 1947

By Harlan A. Walker

This paper on the mines of El Potosi Mining Co. is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of North America. Grateful acknowledgment is made of the helpful suggestions and criticisms offered by the management, together with the assistance of the mining staff in preparing maps and drawings and of C. L. Thornburg, mine geologist, in preparing the section on geology.

Jan 1, 1934

By Dennis McLaughin

This report contains a description of the contract activities performed by ENSCO, Inc. under contract No. H0178069. The purpose of this project was to enhance the Bureau of Mine?s Cableless Electronic Survey System use to aid in the drilling of long (approx. 2000 feet) boreholes in coal. This drilling is performed as part of the methane drainage program. The system that was ultimately developed was field tested 2nd demonstrated in actual in-mine drilling activities. The significance of this system as compared to previous drill survey systems is the fact that it surveys without having to be inserted and removed for each survey point. It is so designed that it can withstand the shock and vibration experience by the drill string during drilling. This means an increased productivity is now possible in that drill operators can determine drill bit positioning in a near real-time environment.

Jan 1, 1981