Search Documents

By David C. Oyler, Dennis R. Dolinar, Christopher Mark, Craig S. Compton

Fully-grouted roof bolts comprise more than 80% of the primary roof supports used in U.S. coal mines. However, nearly 1,500 MSHA reportable, non-injury roof falls occur each year, and most of these are attributable to failure of the roof bolt system. Anchorage failure is one failure mechanism for fully-grouted bolts. As roof deformation works its way upward, the bolts can become heavily loaded near their upper ends. If the applied load exceeds the anchorage, the bolts will simply pull out. Research dating back 30 yrs indicates that this type of anchorage failure is most likely when the roof rock is weak, just where roof support is most critical. In soft shale or coal roof, the small amount of data available in the literature indicates that 20-30 in of resin anchorage may be required to achieve the full capacity of the bolt. In other words, the “full resistance zone” of a 60 in bolt may actually be just 30-40 in. Despite its potential importance, there is no widely accepted anchorage test for fully grouted bolts. Standard pull tests have sometimes been employed, but they provide no information on the anchorage near the top of the bolt. An alternative, first described more than 25 yrs ago in the U.S., is the short-encapsulation pull test (SEPT). With this test, the bolt is installed with only a short (1 ft or less) tube of resin. In recent years variations of this test have become international standards. v

By Irving Hartmann

Falls of roof in coal mines and means of preventing them have been subjects of study for many years, and ran extensive literature has resulted, Usually each individual paper has placed 'emphasis on one phase of the subject, such as fatalities, nature and extent of nonfatal injuries, methods of tembering (particularly in rooms or other wide places), safety along retreating rib lines, and methods of causing falls in abandoned areas. It is only in recent years that there has been persistent question as to why

Jan 1, 1941

By Thomas M. Barczak

The initial Support Technology Optimization Program (STOP),Version 1.0, was released at the 19th Ground Control Conference. This original program has since been updated to Version 2.3 which was released in May, 2001. This paper describes the additional features of Version 2.3, focusing primarily on the following three aspects: (1) including uncontrolled convergence into the design requirements for standing roof supports, (2) the addition of design procedures for cable bolts as an alternative secondary roof support, and (3) the addition of new standing roof support technologies. Another new feature which should facilitate the development of design criteria for standing roof support is the capability to define ground reaction curves through convergence measurements alone without having to make support loading measurements. There are several other new features provided in Version 2.3 which are only briefly addressed in the paper. These include: (1) additional graphics capabilities to facilitate rapid assessment of support comparisons, (2)an East-West designation for support selection to more accurately provide cost and support availability data, (3) additional safety measures including a safety factor to identify support design near the peak support capacity, checks to see if the support dimensions comply with aspect ratio requirements, and a measure of roof coverage for the design layout of the support system. These new features of STOP provide more capabilities to design and analyze secondary roof support systems for conditions which could not be fully analyzed in the original version of the program.

During the period 1979 thru 1982. Multi Mineral Corporation conducted a mining research program at the United StAtes Department of the Interior's Bureau vi Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and. the results are described in this report.

Jan 1, 1983

To improve the air quality in large-opening stone mines by developing better ventilation techniques, including appropriate fan selection in conjunction with air-coursing methods. Background Stone mines are the most common underground large-entry mines in the United States. Data from the Mine Safety and Health Administration (MSHA) for the year 2000 indicate that there were 162 active nonmetal underground mines in the United States, of which 117 were stone mines. Many underground stone mines are drift mines developed from previous quarry operations. Typically, these room-and-pillar mines have entries that are 20 ft or higher and at least 40 ft wide. These large dimensions lead to a very small ventilating pressure loss, even when significant air quantities move through the mine. This is especially true of drift mine operations where ventilating pressure losses of <0.25 in w.g. are common. Underground stone mines with shafts that are<200 ft deep typically have ventilating pressure losses that are <2 in w.g. The pressure losses through these mines are much lower than those of a typical coal mine or deep metal/nonmetal mine. Therefore, the ventilation techniques and principles are quite different. In addition, because of new MSHA regulations that limit the concentration of diesel particulate matter, these mines may need to greatly increase their ventilation airflow. Therefore, large-opening mines need a fan that can move large air quantities and operate at low static pressures. There are three fan types for mine ventilation: centrifugal, axial vane, and propeller. Centrifugal fans are uncommon in underground stone mines as they are often associated with mines requiring the highest of ventilation pressures. Axial vane fans are widely used in all types of mining operations. They are the most common fan type currently found in underground large-opening stone mines. However, they typically do not operate at low static pressures with high efficiency. Propeller fans are currently uncommon in underground stone mines. They are designed for low static pressures and large air quantities at higher efficiency. This fan type best suits the ventilation needs in large-opening stone mines?they produce large air quantities at low pressure losses. Mines with air shafts<100 ft long and at least 12 ft in diameter have fairly low mine static pressures and may also benefit from propeller fans.

Dec 1, 2002

By Elaine T. Cullen

Miners, like many skilled blue-collar workers, are not traditional learners. They have not always been successful in classroom-type settings, preferring to learn on the job in a hands-on environment. U.S. law requires that miners have a minimum of 8 hours of safety training annually, plus 40 hours for underground miners and 24 hours for surface miners when they enter the industry. However, miners rarely view this training time positively. In fact, it has been called “safety jail” by many, who regard it as a time to get a little extra sleep While mining has become far safer in the past 100 years, it is still a dangerous occupation. The Office for Mine Safety and Health Research, a part of the National Institute for Occupational Safety and Health (NIOSH), has funded a project for the past 4 years to address this challenge. The purpose of the research was to find a way to develop effective safety training for these people. Miners are born story tellers. They share “near miss” stories, stories about master miners they have known, and stories about how things used to be. These stories not only pass along information about what will happen if a miner fails to respect the mining environment, they also instruct listeners in the culture of mining and the values that it embraces. Stories, it seems, are a way to get safety messages across to miners, especially inexperienced ones, and using older, wiser miners in these stories is an obvious choice. This paper will discuss how a series of training videos was developed, how “master miners” and story lines were chosen, and how the resulting videos have been received in the mining industry.

By R. Mark, R. Richards

The Washington National Cathedral is one of the largest masonry structures in the USA, and like many of its European Gothic counterparts, it required nearly a century to construct. The design was altered during this period, resulting in greater loadings than were originally anticipated on the soil beneath the foundation. When signs of continuing differential settlement were observed in the early 1990&apos;s, the Cathedral approached the US Bureau of Mines (now the National Institute for Occupational Safety and Health (NIOSH)) for assistance in monitoring the movements of the massive towers and walls. An array of dual-axis tiltmeters was installed about 40m above ground level to measure wall and tower inclination, with the data sent over a dedicated phone line to the NIOSH Pittsburgh Research Laboratory for processing. Mechanical gages and string-potentiometers are also being used to measure motion across cracks and joints, and differential pier settlement is being monitored with optical-level surveying. Data have now been collected for almost 7 years, and they show a long-term settlement trend masked by dramatic diurnal and seasonal thermal movements. The paper discusses the major findings of the study, implications for the future of the Cathedral, and conclusions regarding the use of geotechnical monitoring at major national monuments.

By Peter Swanson, Collin Stewart, Wendell Koontz

A seismic monitoring network has recently been installed in the North Fork Valley coal mining region of western Colorado as part of a NIOSH mine safety technology transfer project with two longwall coal mine operators. Data recorded with this network will be used to characterize mining related and natural seismic activity in the vicinity of the mines and examine potential hazards due to ground shaking near critical structures such as impoundment dams, reservoirs, and steep slopes. Ten triaxial strong-motion accelerometers have been installed on the surface to form the core of a network that covers approximately 250 square kilometers (100 sq. miles) of rugged canyon-mesa terrain. Spread-spectrum radio networks are used to telemeter continuous streams of seismic waveform data to a central location where they are converted to IP data streams and ported to the Internet for processing, archiving, and analysis.

By Irving Hartmann

Falls of roof in coal mines and means of preventing them have been subjects of study for many years, and an extensive literature has resulted. Usually each individual paper has placed emphasis on one phase of the subject, such as fatalities, nature and extent of nonfatal injuries, methods of tembering (particularly in rooms or other wide places), safety along retreating rib lines, and methods of causing falls in abandoned areas. It is only in recent years that there has been persistent question as to why

Jan 1, 1941

By Frank E. Chase, Deno M. Pappas, Christopher Mark

Multiple seam interactions are a major ground control hazard in many U.S. underground coal mines. The two most common types are: • Undermining, where stress concentrations caused by previous full extraction in an overlying seam is the primary concern, and; • Overmining, where previous full extraction in an underlying seam can result in stress concentrations and rock damage from subsidence. The National Institute for Occupational Safety and Health (NIOSH) has completed a major study aimed at helping to identify the location and likely severity of these interactions. In the course of field visits to mines throughout the U.S., more than 300 multiple seam case histories were assembled into the largest data base of multiple seam case histories ever collected. These data were analyzed with the multivariate statistical technique of logistic regression. The study also employed LaM2D to estimate the multiple seam stresses, ALPS and ARMPS to determine pillar stability factors, and the CMRR to measure roof quality. The study resulted in the development of a computer program, called Analysis of Multiple Seam Stability (AMSS), which can help mine planners to evaluate each potential interaction and take steps to reduce the risk of ground control failure. AMSS first evaluates pillar design by calculating the single seam Stability Factor (SFSS) using ALPS or ARMPS. It also automatically generates a LaM2D analysis that provides the additional multiple seam stress so that the final, multiple seam SFMS can be determined. The second part of the AMSS procedure builds upon the statistical findings that overmining is much more difficult than undermining, isolated remnant pillars cause more problems than gob-solid boundaries, and weaker roof significantly increases the risk of multiple seam interactions. AMSS quantifies these effects and predicts the outcome in terms of three levels of risk: GREEN (where a major multiple seam interaction is considered unlikely), YELLOW (where adding a pattern of cable bolts or other equivalent supplemental support could greatly reduce the probability of a major interaction.), or RED (a major interaction should be considered likely, and it may be desirable to avoid the area entirely).

By Alex C. Smith

The National Institute for Occupational Safety and Health (NIOSH) and Northwest Barricade LLC (NWB) conducted a study to evaluate the effectiveness of a novel fire blocking gel for use in underground coal mines to extinguish or to retard the growth of a coal fire. The gel agent was subjected to controlled laboratory testing to assess its ability to delay coal ignition. It was then evaluated to determine if manual fire hose application could be used to apply the agent to mine roofs and ribs to provide a safe egress for mine rescue teams from a fire area. The gel agent was also evaluated in a water sprinkler system to determine its potential for use in conveyor belt fire suppression systems. The agent was then tested in live-fire exercises to examine its effectiveness in retarding and extinguishing a deep-seated coal fire and wood fire. Lastly, the ability of a Mine Rescue Team to quickly and safely apply the gel agent to a mine entry during a simulated mine fire exercise was determined.

Jan 1, 2010

By Leonard J. Prosser, Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

The room-and-pillar mining method is used extensively in underground limestone mines in the Eastern and Midwestern U.S. The rock mass is typically a near-horizontal, bedded deposit at relatively shallow depth. A survey of 34 mines was conducted in which data on roof spans, rock mass properties and support practices were collected as part of a National Institute for Occupational Safety and Health research project into ground control in limestone mines. The average room width is 13.5 m (44 ft), accommodating large mechanized equipment. The results show that the immediate roof beam can consist of many individual layers and can contain several near-vertical joints. In spite of the room widths, the roof is naturally stable in many mines. Observed roof instabilities can generally be related to excessive horizontal stresses or unfavorable geological structures that cause block fallout or beam failure of the bedded roof rocks. The survey showed that the rock mass quality of the limestone does not vary significantly throughout the Eastern and Midwestern U.S. Roof conditions and the need for support were found to be closely related to the thickness and competence of the first layer of limestone in the roof. The findings highlight the need to identify local geological structures and the roof beam characteristics so that support alternatives can be evaluated. Monitoring and observational technologies that are available for identifying potentially unstable roof are presented, which include: roof characterization using the Rock Fall Risk Index, automated logging of roofbolt hole drilling, microseismic monitoring and displacement monitoring.

By Haskiel R. Shell

Methods of chemical analysis of clays for the following constituents are presented: moisture, ignition loss Fe2O3, TiO2, P2O5, CaO, MgO, Na2O, K2O, total. carbon, carbonate carbon total sulfur, soluble salts, and soluble sulfate. In these procedures the attainment of accuracy has been the primary consideration sample was taken to insure accuracy, with ordinary precautions. The procedures may therefore be somewhat somewhat and will not be suited for routine work on samples for which the approximate analysis is already known and in which the need for accuracy is not very exacting. However, the method shod be as a set of detailed directions, that have been tested and shown to yield accurate results with clays and other aluminum silicate minerals. Among these minerals are clays of all types, bentonite bauxite, shale, brick; soil, calcined refractory, and sand. Although some of the methods are Unusual, no particular claim is laid to originality. The material was drawn frail many sources, put together and tested.

Jan 1, 1949

By Andrew M. Leszcykowski

A 1981 U.S. Bureau of Mines investigation indicates the Panamint Dunes Wilderness Study Area (WSA) has one active (intermittent) mine,--borrow pit MS 242 owned by the California Department of Transportation (Cal Trans). This mine produces cinders for road base and traction grit. It contains about 900,000 tons of inferred reserves. Examination and sample analyses indicate the Panamint Dunes deposit, covering about 480 acres of the WSA, may have silica resources and the Green Quartz Claim may have copper resources. Carbonate rocks occur in the WSA, but stone resources have not been identified. Adjacent to the WSA, the Big Four Mine contains 35,000 tons of inferred subeconomic zinc-lead-silver resources, and may have additional resources. Sample analyses indicate the Apple 1 Claim, also adjacent to the WSA, may have silver-lead-zinc resources.

Jan 1, 1985

By Edwin B. Cook

Studies of flame and combustion phenomena at the Bureau of Mines have been facilitated by computer evaluation of the thermodynamic properties of gases formed by constant-pressure burning.4 5 This report is the sixth of a series6-10 presenting results of such calculations; it deals also with constant-volume deuterium-air flames.

Jan 1, 1961

By Fredrick L. Johnson

Tungsten is the principal mineral commodity in the Laurel-McGee RARE II area; copper and molybdenum would be recovered as by-products with the tungsten. Indicated and inferred tungsten marginal reserves at the Hard Point Mine (fig. l, no. 10) are 16,000 tons (14,000 t) averaging 1.0 percent tungsten trioxide (W03). The mine is outside the RARE II area, but the geologic structure that it is on extends into the area. Indicated subeconomic zinc, silver, copper, and lead resources at the Lucky Strike Prospect (fig. 1, no. 7) are nearly 6,200 tons (5,600 t) averaging 5.45 percent zinc, 0.5 oz silver per ton (19 g/t), 0.40 percent copper, and 0.32 percent lead. Although tungsten has been produced at the Tiptop Mine (fig. 1, no. 12), resources were not calculated because of the spotty nature of the tungsten mineralization. Additional exploration at the Tiptop and Hard Point Mines could reveal significant resources. The potential for tungsten resources at the Payday Prospect, Tungsten Prospect, and Morhardt Mine is also high. The Pine Creek Mine custom mill, located about 35 mi (56 km) southeast, could process tungsten concentrates from the area. Tungsten production has been recorded from three properties, the Hard Point, Morhardt, ant Tiptop Mines. Output was about 405,000 lb (184,000 kg) of W03, nearly all from the Hard Point.

Jan 1, 1983

By John K. Owens, Wayne L. Howie

Mobile roof support (MRS) machines are used as roof support during pillar recovery in retreat operations in lieu of wooden posts, cribs, or hydraulic props. A Mine Safety and Health Administration-permissible load rate monitoring system was developed for the MRS by researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. The system uses a dedicated embedded processor to monitor changes in pressure inside the hydraulic cylinders of the MRS through multiplexed data acquisition channels and converts these pressure changes to load rates that sequentially activate three load-rate-indicator lights mounted on the machine. Each light represents a different loading rate to alert mine personnel to dangerous conditions during pillar extraction.

By Stephen C. Tadolini, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A Major Hazard Risk Assessment (MHRA) was developed in Australia after a series of mine disasters in the 1990’s. A MHRA is used to help prevent major hazards, i.e. fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, from injuring miners. A MHRA is a structured process that identifies the characteristics of major hazards, assesses and ranks the risk they present, and evaluates engineering and administrative controls to mitigate them. These controls typically consists of a broad spectrum of prevention, monitoring, first response, and emergency response techniques and helps to move an operation from a reactive to a proactive approach towards safety. This paper documents a MHRA performed at an underground mine where strata instabilities and fire hazards may threaten the condition of its escapeways. The objective of this MHRA is to 1) identify what hazards could affect the egress through the mine’s escapeways, 2) determine what unwanted events pose the greatest threat for the mine, and 3) recommend a plan to prevent or recover from the potential disruption of egress through the escapeway. The plan provides information on the key existing controls that should be monitored and audited, and makes recommendation of new potential controls to further reduce related risks. By documenting the use of MHRA to this specific ground control issue, this paper provides a framework for others to judge the merits of this approach and to help design and perform these activities.

By Eric S. Weiss, Deno M. Pappas, Timothy M. Barton

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has been evaluating developments with surface support liners which includes shotcrete and thin spray-on liners (also referred to as sealants, coatings and membranes) from a ground control perspective. The proper selection and use of a surface support material can significantly enhance ground control which may result in a decrease in worker related injuries due to ground falls. The purpose of this paper is to evaluate the preliminary findings of a long-term underground study of various types of surface support liners, and to examine installation practices that are critical for an effective liner material application. The underground study utilizes NIOSH’s Lake Lynn Laboratory Experimental Mine to evaluate the long-term performance of several types of shotcrete and thin spray-on liner materials. Liner material performance to date was evaluated on a regular basis over a three year period. Although the study is still ongoing, critical mining practices were identified that may seriously affect the bond of the liner material to the mine roof and rib.

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook (volume III) contains overall injury experience and employment data at bituminous-coal, lignite, and anthracite mines, coking plants, metal and nonmetal mines, metallurgical plants, and stone quarries in the United States for the calendar year 1956. Volume I of the Yearbook includes injury experiences and related employment data in the metal, nonmetal, and quarrying industries, and in the milling operations connected with the mining of those commodities. Volume II contains the injury and related employment experience of the coal mining, coking, and oil and gas industries. Reporting is voluntary on the surveys conducted by the Bureau of Mines to collect injury and employment data in the mineral industries, except in the coal-mining industry, where operators are required by Federal law to furnish the information requested.

Jan 1, 1958