Search Documents

By Robert Merritt

Approximately 2,500 tons of low-grade uranium ore were used to conduct a field-scale heap leaching test as well as throe column leach tests. The ore used to construct the field-scale heap leaching test had a grade 0.023% U308 while the ore used fur column leach tests had a grade of 0.027% U308. The ore was crushed to minus 4 in. The field-scale heap was constructed on a clay base with parallel effluent lines running under the heap spaced 7.5 ft apart. The heap was leached for 45 days, drained, washed, and dismantled. Based on residue analysis, approximately 205 tons of ore were leached with a final U308 extraction of 96%. The heap was 17.9 ft in height and leached in a near-vertical pattern down to approximately 1 ft, at which point the leached zone become bell-shaped. Two 8-ft column charges and one 18-ft column charge were leached for 36 and 45 days, respectively. Based on residue analyses, all U308 extractions were greater than 96%. The conclusions generated by the studies showed that (1) flow rates were similar for column leaching and field-scale leaching, (2) final U308 extractions were the same for both types of leaching; however, the deeper ore beds tended to require longer leaching times, and (3) the reagent requirements were reduced with increased bed depth.

Jan 1, 1980

By K. K. Kelley

The first bulletin (269) 3 in this series, which appeared in 1932, compiled the entropy values then available for the elements and in-organic compounds, results being listed for some 150 substances. Elaborations and revisions followed in 1936 (272) and 1941 (280), when over 500 usable entropy values were tabulated. The present bulletin constitutes a further elaboration and revision. The accumulation of data since 1940 has been marked, and 800 entropy values now are available. The present bulletin also contains all the pertinent explanatory matter that appeared in its predecessors. Thus, it retains the same dual purpose of assembling the available values of the entropies at 298.16° K. of the elements and inorganic compounds and giving enough explanation of methods of calculating entropies to make the results comprehensible.

Jan 1, 1950

By Robert Stefanko

The following tables contain the average, maximum and minimum power parameter levels for several mining machines. Power factor is listed only for defined transducer output regions. The reasons for the undefined areas are provided in the Instrumentation Chapter. Several maximum voltage drops are included, and are computed from the no load line-to-line voltage: Again, the drops are from measurements at the low side of the load center. The machines are: Continuous Miners; F6A Alpine 76AM Jeffrey (d-c) 8CM Joy 8CM (10CM) Joy 9CM-2AH Joy loam Joy CU-43-2H Joy 2 each CM26H Lee-Norse CM28E Lee-Norse Shuttle Cars; 18SC Joy 48S Torkar (a-c) 2 - 10SC Joys input to rectifier 2 - 16SC Joys input to rectifier

Jan 1, 1973

By William R. Archibald

This report presents the results of a program demonstrating the technical and economic feasibility of hydraulic borehole mining of uraniferous sandstone. This mining technique involves the drilling of a borehole from the surface down into the ore body. A borehole mining tool consisting of a high-pressure cutting jet and a slurry jet pump is lowered down the borehole. Water from the high-pressure cutting jet cuts into the sandstone formation generating a water-sand slurry which flows to the slurry jet pump and is pumped to the surface. The cutting jet is rotated and moved up and down from the surface, thereby generating a cavity in the formation. When the cavity size reaches a point beyond the effective radius of the cutting jet, the mining tool is moved to an adjacent borehole and the process is started again. This program was carried out in four phases. Phase I included modifications to the borehole mining system (built and tested under a previous contract, No. H0252007, for the mining of coal) and factory tests of the jetting system. Phase II covered the field tests and a public demonstration. Phase III involved nozzle and equipment modifications and factory tests. Field testing continued under Phase IV along with an evaluation of this method. The field tests were conducted successfully on Rocky Mountain Energy Company's Nine Mile Lake property near Casper, Wyoming. Results indicate that; hydraulic borehole mining of uranium is technically feasible (300 tons of uraniferous sandstone were mined from a depth of 90 ft) and the hydraulic borehole method is economically attractive. However, additional testing is required to clearly define the economic feasibility.

Jan 1, 1978

By John J. Henn

An evaluation is presented of the Bureau of Mines process for the recovery of metal and mineral values from municipal incinerator residues. This process employs standard mineral beneficiation techniques and is operating on a pilot-plant scale of 1,000 pounds of incinerator residue feed per hour. Products from this separation process include ferrous, aluminum, and copper-zinc scrap, and colorless and colored glass. Cost estimates were prepared for four plant sizes. The estimated capital and operating costs For the four plants follow: [ ] It is assumed that the separation plant is located adjacent to a municipal incinerator. Provision is made, however, for part of the residue feed to be delivered by truck so that one large separation plant can be used for residue from more than one incinerator.

Jan 1, 1971

By Don M. Coulter

"INTRODUCTION The Margerum bauxite district, in Colbert County, Ala. was investigated in December 1940 and in February 1943 by R. W. Smith of the Bureau of Mines .3/ A geologist of the Federal Geological Survey investigated and mapped the district in the fall of 1942.These preliminary investigations indicated bauxite showings over an area about a mile long by 2,000 feet wide. It was felt that the chances were good for finding one or more large deposits of low- to medium-grade bauxite. The location - within 35 miles of the alumina plant of the Reynolds Metals Co. atLister Hill, Ala. – made it especially attractive. A field office was established in Iuka, Miss., on May 19, 190,, and mineral agreements were executed with four landowners covering 1,146.6 cores.The drilling on the project was done under contract. The power drilling was supplemented by a labor crew that drilled hand-auger holes, where there was little or no gravel overburden, and sampled the old test pits.The Federal Geological Survey, after thorough study of the district, recommended 54 drill holes 4/ to delimit the known deposits and to search for possible extensions. After the drilling started, many of these locations eliminated, and others were changed upon the basis of information gathered from the holes as they were drilled."

Mar 1, 1948

By E. G. Davis

This report summarizes an investigation to determine the occurrence and recoverability of heavy minerals in sand and gravel operations in the Southeastern United States. A total of 61 samples from 34 sand and gravel operations in Alabama, Georgia, South Carolina, and North Carolina were studied. Heavy minerals, in amounts ranging from 3 to 400 pounds per ton, were found in all of the samples. Eighty percent of the samples contained 20 to 40 pounds per ton of heavy min¬eral. Valuable heavy minerals, in order of decreasing amounts, were ilmenite, kyanite, zircon, rutile, and monazite. Large-scale concentration tests were made on five samples from four major producers. Gravity concentration by Humphreys spirals and tables resulted in bulk heavy mineral concentrates that graded from 82 to 98 percent total heavy minerals. Mineral recoveries ranged, in percent, as follows: Ilmenite 60 to 95; zircon 96 to 100; kyanite 37 to 77; rutile 89 to 100; and monazite 96 to 100. Separation studies on the gravity concentrates showed they would respond to high-tension and high-intensity magnetic separation techniques to produce individual mineral concentrates. The recovery of each individual mineral from fractionation of the heavy mineral gravity concentrates, in percent, was: Ilmenite 77 to 94; rutile 41 to 68; kyanite 62 to 79; zircon 49 to 83; and rare-earth products, monazite and xenotime, 42 to 96. The grade of each mineral concentrate was: Ilmenite 51.1 to 68.7 percent Ti02; rutile 93.7 to 94.3 percent Ti02; kyanite 55 percent A1203; zircon 58 to 61 percent Zr02; and rare-earth products containing 73.8 to 90.8 percent monazite and 4.8 to 12.7 percent xenotime.

Jan 1, 1971

By Thys B. Johnson

The mine system analysis and evaluation study presented in this report was part of the U. S. Bureau of Nines' Tertiary channel project conducted under the Heavy Metals program. The Badger Hill pit, located on the west end of the San Juan Ridge area, near Nevada City, California, was the site of the Bureau's field work. The objectives of this study were: (1) Determine potential alternative mining systems for some of the large tertiary channel gold-bearing gravel deposits, and (2) Identify areas of technology where further investigation would be merited because of their potential inclusion in a mining system for such deposits, The study involved the development of a mineralized block inventory, an economic block inventory, determination of optimum ultimate mining limits and a preliminary economic mining system evaluation. Computer programs were developed and utilized for each of the study phases stated above. The sampling program conducted at Badger Hill by the Bureau Delineation Group together with confidential drill hole data provided by the San Juan Gold Co. formed the basic gold values and distribution information from which a deposit model was developed. The deposit was divided into minable block units and net economic values were assigned to each block for various configurations of both open-pit and underground mining methods based on cost and performance data provided by the various Bureau of Mines Research Centers. A number of controllable variables such as: (1) Mining method (open-pit and underground), (2) depth of mining cut, (3) production rate and (4) equipment type and capacity were evaluated. The prime measures of effectiveness on which the mining systems where judged were discounted cash flow rate of return and maximum utilization of natural resources. The analysis showed that underground mining of the Six-Mile Tertiary channel gold-bearing gravel deposit under consideration was uneconomical and did not permit maximum recovery of the resources within the channel. It was also apparent that mining the Six-Mile Deposit for gold alone is uneconomical or at best marginal at a gold price less than $80 per ounce. The analysis showed that the potential for an economic mining operation within the Six-Mile Deposit exists when the gravel resources of the channel are considered together with the gold. It was determined that the highest rate of return would be realized with a 20-year open-pit mining operation yielding 745,000 ounces of -gold and 55 million cubic yards of usable gravel.

Jan 1, 2012

By Michael Rieber

An analysis of coal slurry pipelines was presented in our May 1976 study, Route Specific Cost Comparisons: Unit Trains, Coal Slurry Pipelines and Extra High Voltage Transmission (4]. The present study extends that analysis. The earlier work included technical and economic cost descriptions of the black Mesa and ETSI pipelines as well as some hypothetical pipeline routes. Water problems, safety and environment, required resources, and labor impacts were discussed at some length. Additionally, pipeline impacts on competing railroads, slurry-rail comparisons, and cost escalation. were analyzed. The difference in pipeline profitability to an owner-operator versus a promoter-builder was suggested. These aspects are not redone in this study. Here, we present a synopsis of the previous results and a general statement of coal slurry pipelines. Extensions of the arguments are presented where they appear warranted. New material is developed in the area of pipeline branching and tapping. This would appear necessary if slurry pipelines are to function as more than private lines; if they are, for example, to be responsive to common carrier requirements.

Jan 1, 1977

By Ad. Breyre

[Internal-combustion engines have been used in Belgian mines for a long tine. As early as 1899, the use of these engines underground was considered, but the general policy was to prohibit such an application unless ministorial permission was granted' in special instances. At that time only gasoline engines were available, and a few of these were installed as stationary engines, although in general they were replaced later by electric or compressed-air motors. However, the number of gasoline locomotives continued to increase. Regulations governing the use of these locomotives soon were formulated and as early as 1920, when a now set of regulations was promulgated, the use of gasoline locomotives in mines could be authorized by the Provincial Inspection Department and no longer depended on obtaining a ministerial decision. Since 1931 this authorization may be given by the Chief Inspector of Mines, Director of the Mining District. Since 1920, safe practices have boon incorporated in the regulations.]

Jan 1, 1940

By Ad. Breyre

Internal-combustion engines have been used in Belgian mines for a long time. As early as 1899, the use of these engines underground was considered, but the general policy was to prohibit such an application unless ministorial permission was granted in special instances. At that time only gasoline engines were available, and a few of these were installed as stationary engines, although in general they wore replaced later by electric or compressed air motors. However, the number of gasoline locomotives continued to increase. Regulations governing; the use of these locomotives seen were formulated and as early as 1920, when a new set of regulations was promulgated, these of gasoline locomotives in mines could be authorized by the Provincial Inspection Department and no longer depended on obtaining a ministerial decision. Since 1931 this authorization may be given by the Chief Inspector of Mines, Director of the Mining District. Since 1920, safe practices have been incorporated in the regulations.

Jan 1, 1940

By R. H. Hiltz

One of the major hazards in underground coal mining is fire. The inherent hazard of fire is exaggerated by the nature of coal mining restricted areas, the highly combustible nature of coal itself, and a potential for explosive concentrations or dust and gas in the air it becomes imperative therefore to make every effort to eliminate the causes of fires, while providing the most effective means possible to control and extinguish those fires which may occur it has been demonstrated by prior work that the problem of control increases in proportion to the time necessary to institute control procedures. There are several areas of underground coal mining with obvious fire potential. Some of these, like belt heads, have reliantly undergone improvements in standby fire control devices Others, although having fire suppression systems available to them, have not received as complete a systematic study of their problems. Face machinery, particularly those without a water supply, falls in this latter category.

Jan 1, 1973

By H. J. Sloman

Mining laws of the several coal-producing Stat e with respect to safety catches on mine cages and their testing are extremely variable and generally indefinite in scope. The most specific requirements are contained in the Coal Mining Laws of Washington,3/ as follows:

Jan 1, 1944

By Eric Nordhausen

This report and associated deliverables is the culmination of a comprehensive literature survey, data collection and identification of over 500 metal/nonmetal active mines/mills/smelters (over 50,000 tons per year, TPY, production) in the contiguous 48 states. The main purpose was to compile an inventory of the mine/ mill/smelter waste tonnages, thus forming a data base for future research and development in improving waste management and waste disposal techniques in the metal/nonmetal mining industry. The study specifically excluded sand and gravel, sulfur, granite and any commodity that leaves basically no waste when mined and/or milled. The coal waste inventory is the subject of another report. The study provided for locating, mapping. encodating and digitizing all the mine/mill/smelter information made available throughout the nation as well as the climatological, land use, topographical, ecological and vegetative data. Mine/mill/smelter information also included (where possible) acreage and/or volume, mining methods, primary ore and gangue minerals, waste composition and haulage methods and distance hauled. Finally, a discussion is provided concerning present and potential uses of various types of tailings, as well 8S recommending possible R&D in addressing problem areas in waste disposal techniques and management.

Jan 1, 1981

By Richard A. Winters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 49,875 acres of the 54,833-acre Big Jacks Creek Wilderness Study Area (ID-111-7C) in order to evaluate the mineral resources. The study area is located in Owyhee County, ID, about 15 miles southwest from Bruneau, ID. No mining districts are in the study area, but part of one placer claim, located in 1924, extended into it. The northern portion of the area was covered by oil and gas lease applications; all were cancelled prior to 1985. No economic concentrations of minerals were found in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Big Jacks Creek study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By Parry. V. F., John B. Goodman

"INTRODUCTION The Denver region coal field, covering an area of approximately 7,640 square miles, extends from the Wyoming State line to the middle of El Paso County, Colo. The coal in this region is subbituminous in rank. Much of it is used as domestic fuel. During the last decade the production of coal in this field has remained fairly constant at an average of 2,600,000 tons per year. This production has come from 50 to 60 mines, 88 to 90 percent of the production being from the section of the field north of Denver.According to the Standard Specifications for Classification of Coal by Bank of the American Society for Testing Materials 4/ the coals in this region are classified in the Subbituminous B and C group. On the as—mined basis, they contain about 22 percent moisture and average 9,600 B.t.u. per pound. They are noncoking and slack to a variable extent when exposed to the weather. This is characteristic of subbituminous coals."

Aug 1, 1939

By Eric E. Unger

Results are presented of a census of the machines used in surface coal mines in the United States. The numbers of each machine type and model reported to be in use are tabulated for large and small mines in the Eastern, Central, and Western regions. Also tabulated are the average daily usage times of the major machine categories and the numbers of machines that have acoustical and other cabs. Projections of the total numbers of primary production machines are given. It is found that heavy tracked dozers and wheeled front end loaders constitute the most prevalent machine types, and that generally a very few models of machines made by one or two manufacturers constitute a major fraction of the population in each machine category. About 70 percent of all machines are reported to have some kind of cab, and about half of these are reported to be acoustical gabs; it is noted that acoustical cabs generally came into significant use since about the early 1970's. It is observed that the percentage-wise mixes of equipment types used in the various categories of mines differ significantly for only a few types of machines, notably for heavy dozers and loaders, and for haulers, highway trucks, and internal-combustion engine-powered shovels and draglines.

Jan 1, 1977

By Walter Frank

The purpose of the work covered by this contract is to develop a ground and pilot conductor connector which will significantly improve mine trailing cable splice performance. This work compliments the work completed under Contract 00357100 on the development of crimp connectors for the phase conductors of trailing cables. A brief discussion on splice problems is presented as an introductory means and substantiates the need for the development and test programs outlined in this report. As with the phase development work, the ground and pilot connector work is essentially of an empirical nature. As a result time is devoted to explaining the derivations of the test procedures used. In order to familiarize the reader with connector terminology a section is devoted to a glossary of pertinent terms. The connector design effort includes connectors for splicing ground and pilot conductors. A distinction is made between connectors suitable for splicing round and flat ground configurations. The same also applies to the pilot conductors. During the course of this work, much time has been devoted to the question of suitability of round cable configurations for trailing cable applications. This is discussed in detail along with resulting conclusions and recommendations. A field test program was conducted in order to confirm ground and pilot connector laboratory data. This testing also determined the viability of the connector designs and recommended installation techniques in a mine environment.

Jan 1, 1979

By J. L. Thompson

The U.S. Bureau of Mines conducted a water-jet-studies program using a single-bit, in-seam test unit to determine effects of a moderately high-pressure (up to 10,000 psi) water-jet-assisted cutting system on rock weakening. The in-seam test unit was used to obtain cutting force data in tangential, normal, and side force directions. Conical continuous miner and radial longwall miner bits were used to penetrate test samples of coalcrete, Berea sandstone, and Indiana limestone with unconfined compressive strengths of 4,600, 8,000 and 10,000 psi, respectively. Depth of cut in the coalcrete tests was 1 in, with 2-in cut spacing (2:1 ratio). Because of cutting equipment and instrumentation limitations, the Berea sandstone and Indiana lime-stone were cut using a 0.5-in depth of cut and 2-in spacing (4;1 ratio). Bit velocity was maintained at 25 ft/min for both bits. Each specimen and bit type was tested using 0.3-, 0.6-, 0.8-, and 1.0-mm-diam nozzles and water-jet pressures of 2,500, 5,000, 7,500, and 10,000 psig. Water-jet-assisted cutting decreased average resultant conical and radiallongwall bit cutting forces 6.4 and 8.4 pct in coalcrete, 5.5 and 1.4 pct in Berea sandstone, and 2.0 and 5.5 pct in Indiana limestone. Slight reductions of power requirements resulting from water-jet assist were ascertained during these experiments.

Jan 1, 1989

By Eugene A. Dolecki

This final report describes the work accomplished under U.S. Bureau of Mines Contract #H0242011 - "Feasibility of Automated Rail Haulage Systems in Underground Coal Mines." The report outlines the base for the development and evaluation of automated rail haulage systems in terms of the service requirements for haulage systems in underground coal mines, and of the performance of existing haulage systems. A generalized automated rail haulage system concept is defined. A safety impact analysis of automating the mainline portion of the underground system indicates a 50% reduction in injuries and fatalities. A cost effectiveness (over the total life cycle) study for the system indicates a cost benefit can be obtained from implementing an automated rail system. The design specifications for the total automated rail haulage system - including subsystems and components -are developed, and the equipment types and general design approaches evaluated, with selections outlined. A detailed conceptual design for a prototype automated system is described. Conclusions and recommendations are presented, and a program plan devised for implementing a proto-type automated rail haulage system demonstration in an operating underground coal mine by 1980.

Jan 1, 1976